MOVED: [Athlon64] Clear PnP Data Pool in K8N Neo4 running xp64

This topic has been moved to AMD64 nVidia Based board.
[Athlon64] Clear PnP Data Pool in K8N Neo4 running xp64

Hello !
Strange Problem..... 
You mentioned Problems with your boot-sequence and your Raid Setup. I don´t know exactly but it think this is connected with your SLI Problems. Which Bios Version are you using ? Did you try to make a CmosClear for reinitialising PNP and DMI stuff ? You should also check your Cmos onboard Battery, perhaps its empty.
I have heard about a Problems with this some revisions of this Board, Onboard Battery is emptying very fast sometimes.
Good Luck
Greetz MurdoK   

Similar Messages

  • [Athlon64] Clear PnP Data Pool in K8N Neo4 running xp64

    I recently purchased a MSI mobo, K8N Neo4, running pheonix bios.  I am getting two unknown devices when booting...there are no devices loaded without drivers....so I was thinking, if I 'Clear PnP Data Pool' this should rectify the error...
    Question is....how to on this mobo?  I really don't want to press the reset bios button on the mobo unless there is no other way...
    I've checked out Bios and can't seem to find a way to clear PnP Data...is there another way? Ie. a CMD value I can enter on the windows side?
    Apart from that I'm very happy with the performance of this mobo
    - An EX GIGABYTE Customer

    Hello !
    Strange Problem..... 
    You mentioned Problems with your boot-sequence and your Raid Setup. I don´t know exactly but it think this is connected with your SLI Problems. Which Bios Version are you using ? Did you try to make a CmosClear for reinitialising PNP and DMI stuff ? You should also check your Cmos onboard Battery, perhaps its empty.
    I have heard about a Problems with this some revisions of this Board, Onboard Battery is emptying very fast sometimes.
    Good Luck
    Greetz MurdoK   

  • PROBLEM : BUILDING DMI POOL -WITH- K8N NEO4 PLATINIUM, Ultra nForce 7125

    Hello   
    Problem with motherboard K8N NEO4 Platinum!!!   
    Description - BUILDING DMI POOL 
    Configuration: 
    MOTHERBOARD K8N NEO4 PLATINIUM, Ultra nForce 7125 
    AMD Athlon 64, 3700, Socket 939 
    Video: ASUS Carries to an extreme N6200TC, 256 RAM 
    2 JIG RAM Kingston PC3200 CL3 184-PIN DIMM KIT(2 PSC) model: KVR400X64C3AK2/2G 
    Power Supply RAIDMAX +24 PIN +4 PIN CPU+SATA 450W 
    I want to initialize the PC from the CD to install WIN XP, I can change the beginning sequence FROM the BIOS configuring the CD like first device, but from the menu boot with F11 I cannot change the boot order, this fixed one in the +HHD 
    Already change for several HHD, CD and Power Supply but the continuous problem!!!!!!!!!! 
    I believe that it is a problem with the CMOS it already cleans it from the reset button and it doesn't pass anything!!!!!!! 
    Thank You, for your help…

    Borger_Montr,
    The think you problem maybe the +12V@22A on your Power Supply, I highly recommend a Minimum of 28-30A and I repeat minimum.
    If I am right you can prove it this way, you say you cannot even boot from Floppy drive or CD.
    Leaving you case sides off unplug all of your case fans, power supply, CPU and motherboard Chipset fans are all you need if your turning it on for a short test.
    In addition, Unplug all drives except for the floppy drive.
    Then, insert a bootable disk into the floppy drive.
    Boot the system, it should boot from the floppy with no problems.
    If it boots from the floppy, you need a new power supply and when buy your new PS total power is a useless number.  The +12V output current rating the one to look for on a single rail supply like you have now again 30A Minimum 35-40A would be better, on multiple +12V power supply each rail should be rated at 20A Minimum.  I do not care how many rails you has each must have 20A or more.  Another thing to make sure of make sure the power supply has all the correct cables and connect you motherboard and Graphics cards.  Each graphics card and all of the power connectors on the motherboard should have there own cable with correct plugs that connect directly to the Power Supply.  For no reason should you need any power cable adapters, all that means is that power supply was not meant for your system.
    If you need any more details of instruction or I did not explain something well enough that you understood completely, please reply and ask pacific questions.   
    Roger
    When submitting a problem, include a complete list of your system components; include part numbers, all Power Supply Voltages, and their output ratings.  It is almost impossible to estimate what your problem is without knowing something about it. 

  • How to clear all data when the form loading at the first time

    hi
    I am using JDevloper 10g and I have adfForm page, I want to clear all data when I load the page for the first time.
    When I did it using RefreshCondition on the pageDef in the executables like(
    <executables>
    <iterator id="FinCompaniesInformaton1ViewIterator" RangeSize="10"
    Binds="FinCompaniesInformaton1View"
    DataControl="AppModuleDataControl" *RefreshCondition="#{adfFacesContext.postback==true}"* />
    </executables>
    the form didn't bring any data but the problem is the field in the form at the run time changed to read only. So how to make it inputText and clear the data inside it at the run time
    best regards
    Tarek Al Soudani

    thank you for your help,my spec is I have ADF Form and I have creat and Edit CommandButton I made it befor also Commite to save.
    so when I run the form the Field should be disabled and there are no data inside it,and when I chose the creat button the fields should be enabled and I have to insert data inside it then I save.
    So I have FinCompaniesInformatonView as view object based on entity object name FinCompaniesInformaton and applicationMoudul.
    I tolde you befor that I made refreshcondition to solve the data clearence problem but the field changed to read only so please if you now any way to leave the fields as inputText whitout make the form as creation form
    beast regards

  • MOVED: K8N Neo4-F - i think i have a problem

    This topic has been moved to AMD64 nVidia Based board.
    K8N Neo4-F - i think i have a problem

    Quote from: lparker on 03-December-05, 10:40:24
    The fan will spin at a certian speed depending on the temperature of the chip.  Example: at 20degrees the fan spins at 2000rpm and at 30 degrees the fan will spin at 4000rpm.  This is normal.
    k thx i appreicate the help that took a load off my back. at first i thought id have to go get another MOBO.

  • MOVED: [Athlon64] K8N Neo4 Bios ver 1.50 eats batteries

    This topic has been moved to AMD64 nVidia Based board.
    [Athlon64] K8N Neo4 Bios ver 1.50 eats batteries

    Hi, Takesix.
    Unfortunately, you are not the only person with this problem.  I purchased a non-SLI version of this board about 6 weeks ago and am on my third battery, all from different manufacturers.  The board was originally flashed with V1.50 but I flashed it to v1.30 because I had read that it was a better version.  This has not stopped the draining battery problem.  Have e-mailed MSI and Monarch Computer tech support hoping to get an answer but haven't received any replys yet.  To read others strories go to the following link.     https://forum-en.msi.com/index.php?topic=84120.0  Incidentally, how old is your board?  Wonder if it was a specific lot?

  • MOVED: [Athlon64] AGP problem with my new MSI K8N NEO4-F

    This topic has been moved to AMD64 nVidia Based board.
    [Athlon64] AGP problem with my new MSI K8N NEO4-F

    Yes I managed exactly that. I've been out of the computer building business for a while so I didn't know the graphics ports had changed.
    I will invest in a graphic card as well, thanks for putting me on track 
    (The manual sais something about the port supporting 8x agp though? )

  • Verifying DMI Data Pool

    I have a ms-6533 motherboard (barebone system) and when i try to boot up the system using windows/me & maxtor harddrive, the systems hangs at  "verifying dmi data pool ".
    Please help :]

    jan71942
    New Member
    Registration Date: 01-03-2003
    Posts: 1
     Verifying DMI Data Pool
    I have a ms-6533 motherboard (barebone system) and when i try to boot up the system using windows/me & maxtor harddrive, the systems hangs at "verifying dmi data pool ".
    Please help :]  
    There's not a lot of info to work with here. But here goes;
     First I would recomend opening the case and checking that all cables are where they belong (check the Manual) and that they are well seated. You might want to remove then replace each end of each cable (one at a time) while you're there.
    You might also turn on the power and check if all the fans are running and if the hard drive spins up.
     Try booting up.
     Secondly, try reseating the Memory and CPU. (again, check the manual)
     Try booting up.
     Third, clear the CMOS (manual)
     Try booting up.
     Fourth, turn on the power, hold down the 'Delete' key to enter the BIOS, go to 'Load Fail Safe Defaults'. At this point your system should ask you  if you are shure you want to do this. Click 'yes'. Hit 'F10' to save your change then eigther the 'y' or 'Enter' key depending on your bios.
     System should reboot on its own at this point.
     You can download your manual at: http://download.msi.com.tw/support/mnu_exe/mbd_mnu/E6533v1.0.exe
     Hope this helps.

  • How Long will it take to reset the 16gb ipad with clear all data in it.

    How Long will it take to reset the 16gb ipad with clear all data in it.

    I have the same problem. I try to reset my ipad / iphone 3g using the reset and delete all content on general. It is almost 2 days now but my ipad / iphone 3g are not yet finish. Only apple logo / looping circle appears on the screen. What will i do? thanks... iOS 5.0.1

  • May I clear all data in my cloud and start over

    I have had a joint Apple account with my wife. I want to get a separate Apple account for her and then clear my data on the could and use the current account as only mine. How may I do that?

    Click here and follow the instructions. If the computer originally shipped with Mac OS X 10.6.8 or earlier, when you reach step 5, insert its original disk, restart with the C or Option key held down, use the Disk Utility to erase the internal drive, and install a fresh OS.
    (120133)

  • Some music files do not show up in google play music app library.  I did clear cache/data and restarted phone.  The music is stored on the SD card.  Most of the music in the library is in the same folder on the sd card.  I can play the song from file mana

    some music files do not show up in google play music app library.  I did clear cache/data and restarted phone.  The music is stored on the SD card.  Most of the music in the library is in the same folder on the sd card.  I can play the song from file manager, but it still is not in the music library in play music.

    Cyndi6858, help is here! We'd be happy to help figure this out. Just to be sure though, the Droid Maxx should not have an SD card. Is this the Droid Razr Maxx? How did you add the music to the device? Are you able to see the files and folders located on the SD card or device when plugged in?
    Thanks,
    MichelleH_VZW
    Follow us on Twitter @VZWSupport

  • How to clear the data in my page after user enter submit button

    hi......
    how to clear the data's in my page after user enter submit button. Actually while pressing first time itself the data is uploaded in database.

    Hi Nazeer,
    Instead of doing it on the same button better create a separate button for this functionality, As per my understanding you want to clear these fields to create new record so that you can enter a new record so for this you just need to insert a new row in VO.
    Still if you want to do it on the same button then you need to put the check that particular record is not dirty if it is not then create new record else create new record.
    One more thing if you will clear on the second click of a button how will you update your record??
    Regards,
    Reetesh Sharma

  • HT1751 when i have moved all of my data to an external hard drive should i delete all of the library files on my laptop/PC

    i have moved all of my data to an external hard drive should i then delete the copies on my laptop

    What are you actually trying to accomplish? Backing up the library, or moving it?
    If backing up don't delete anything.
    If moving did you move the library files as well? Ideally you would copy the entire iTunes folder out to the external drive then shift-start iTunes to connect to the relocated library. This method makes it easier to move the library to a new drive or computer later and keeps everything together for backing up. Rather than delete everything rename the iTunes or iTunes Media folder first (depending on which approach you took) and make sure the library still works before deleting.
    tt2

  • Clearing Document Date do not follow the define clearing date in F-03.

    Hi,
    Clearing Document Date do not follow the define clearing date  BKPF-BUDAT in F-03.
    My user received the unpresented check statement from the bank on 31 Dec 2010. As 1 Jan 2011 is holiday and he came back to the office on 5 jan 2011. He post manual upload (Debit : Bank Outgoing and Credit : Unpresented Cheque) posting date 31.12.2010 (period 12/2010 and 01/2011 still open) . Hence the next step (same date on 5 Jan 2011) is to clear the Bank outgoing using F-03. He put 31.12.2010 as his Clearing date BKPF-BUDAT but when the system post the clearing date is 04/01/2011.
    Please help

    Hello,
    Hope it helps.
    But i can recall for the EBS bank statement upload into a previous fiscal year, ie, 31.12.2010.  I had to close the current fiscal year temporarily.
    See what happens in your system when it tries to clear with F-03.  Though as mentioned re-check as F-03 will default to the system date --- today.
    Regards
    Waza

  • Clearing the data buffer from the input fields

    Hi,
    I am using an user exit CONFPP02 for the Tcode: co11n. I have written a program such that the confirmation numbers having the status CNF will not be allowed to be processed. The whole confirmation is terminated when the system checks the confirmation number and its status as CNF. If the status of the confirmation number is PCNF, the program allows the further processing of the Tcode Co11n.
    The problem starts when the user enters the PCNF status confirmation number and enters, the system stores the values in the various input fields. Now without exiting the initial confirmation screen, if the user replaces the Confirmation number of the PCNF status to the Confirmation number of the CNF status , the system issues a warning message:"  Confirmation no. or order/sequence/operation has been changed
    However, the input fields still contain default values from thepreceding confirmation". if the user says yes, the program written is bypassed , thus allowing the reconfirmation of the CNF confirmation number  into PCNF confirmation number .
    Can anybody suggest a suitable method to clear the data stored defultly in the input fields so that the program can be made to work.
    With regards,
    Avinash.S
    Mobile no:09996192456

    Hi Gilad,
    I never use Preview and did not use Preview at all before sending the document over to my most recent client either.
    I only opened Preview up this morning after I discovered that all of the form data had disappeared on his end! And the only reason I opened up Preview was because I already knew it looked fine in Acrobat so wanted so wanted to view the form in a different application.
    My client would not even have notified me about it had he not sent the signed form back to me and I saw there was no data there! I then called him and asked him about the missing data and he said that he thought I had simply sent over the form purposely with blank fields:(
    I have just emailed him to ask him what application he opened it up in. My understanding is that he is on Windows because ne mentioned to me his company was using Windows when we last spoke. Perhaps he has a personal Macbook where he opened it? I just don't know and can hopefully soon find out:)
    But THANK YOU for letting me know about that script! I appreciate it:) I have now downloaded and installed it and will just have to use it on ALL of my forms before sending them out:)

Maybe you are looking for