MOVED: Can't detect second piece IDE hardware

This topic has been moved to AMD64 nVidia Based board.
Can't detect second piece IDE hardware

Quote from: LauritsT on 15-September-05, 14:30:15
Thank you for your replies. I have used the same config om my last MB, so I assume the jumpersettings are ok. I have my HDDs on different cables. Each IDE cable is attatched to a HDD and a CD-burner or DVD device. One HDD is a master and one is a slave. Same goes for the CD/DVD devices.
I'll try setting them to cable select and see if that will solve the problem.
If all of the above suggestions do not pan out try using a different IDE cable. I had an identical problem to yours and after much consternation I decided that it might be the cable. Sure enough after trying several extra cables I had lying around one worked. The MSI one didn't work, other's that worked, (and still work) perfectly fine in my other systems didn't work on my MSI board. For some unknown reason that one special cable did. Lest people think it was a simple configuration problem or that the connectors were not snug or properly set up this was not the case. The IDE system on this MB is , (or at least can be) very sensitive.

Similar Messages

[SOLVED] Z77 Mpower can't detect second graphic card

Hi everyone
I'm experiencing a problem with my Z77 Mpower.
It's not able to detect the second graphic card.
The complete configuration includes:
Z77 Mpower
i5 2500k
2*4Go G.skill 1866MHz
GTX680
8800GT
Crucial M4 256Go
Corsair AX750
The idea was recycling my old 8800GT as a dedicated physx card
Due to massive cooling the GTX680 will be installed on the second port
Both graphic cards works perfectly when installed alone and I also tested with a GTX570 and results are the same
When I install only one card, it works on 1st port at 16x or 2nd port at 8x,
but if there is 2 cards installed only the first works and bus-width is 8x according to CPU-Z, the second one is invisible in windows, GPU-Z or driver
I didn't tested the 3rd port because my sandy bridge has limited pcie lane
I tested it with bios 17.4 and beta H53, results are the same, I also tried with and without 6 pins power supply on the mainboard and the problem is still the same.
I tried this graphic cards configuration on a gigabyte z68 ud4 and same cpu, ram, vga and psu and it works perfectly.
Is there a bios setting to enable multi gpu ? (tried to enable igp multi screen without result)
Is it possible to have defective pcie port for multi gpu when all pcie ports works alone ?
I have another question about this motherboard
is it possible to have a dynamic vcore related to eist while overclocking ?
on the gigabyte z68 ud4 it's possible by setting vcore on normal and playing with load line calibration and offset
on the mpower this settings appears in bios but are not graduated the same way and I don't understand how they works.
Thanks for your help

Thanks for your help flobelix
I already tried and benched this physx configuration on my old gigabyte motherboard
in non physx games the 8x limitation barely don't affect the gtx680
in physx games the 8800gt isn't fully loaded and framerate is near the gtx680 alone with physx disabled.
this configuration gives physx graphical bonus without affecting framerate
the 120W limit of the MK13 may be for fanless use, I have 2 90mm fans attached directly on the heatsink and under furmark the card runs 20°C lower than stock cooling and is very silent
I also kept the stock molded metal plate that cool the power supply and ram under the MK13
But due to this cooling this card can't be installed on the first slot
on the gigabyte until you set the dedicated physx card in the driver both cards and all outputs on cards sends the same signal to screen (bios screen is also sent to all cards)
on my mpower only the first sends signal to screen, but i should be able to set (only for testing purpose) the 8800gt as main device and the gts680 as physx card
unfortunately it don't work because it looks like when a card is plugged on 1st port the mainboard disables the 2nd

HP Phoenix computer can't detect second monitor

HI,
I have used this for a while (18 months) on one monitor and wanted to extend the desktop to a second monitor - but the system fails to detect a second monitor when it is plugged in.
It has an AMD Radeon 6850 with two DVi slots - both monitors work as I can swap them over. But neither the auto detect (HP Catalyst) or the manual detectoption show up a second monitor.
I have updated the ADM driver, restarted etc etc........ not sure what else to try. Any suggestions?
thanks
Mike

Hi MikeJeffries,
I'm sorry to hear about your problem in connecting a second monitor. Here is an article, (assuming you have Windows 8), that may be of help to you: Using Two or More Monitors with One Computer (Windows 8). Let me know if this helps at all. Best of luck to you.
Ryan1216
I work on behalf of HP
The advice and opinions given here are my own and not those of HP

Can't detect second display

I adore this shiny new iMac, but oy, is the learning curve (from 10.4) steep...
The current issue has to do with setting up a second monitor, in this case an old but serviceable 15" NEC MultiSync LCD. I bought the correct adapter to attach to the venerable VGA cable on the NEC, but I'm not getting a signal to it and Displays shows only the main monitor.
My suspicion is that the NEC is just 'too old,' but I'd be happy if it actually could be used. Back in the day I was used to a LOT of real estate (20" Apple and 19" e-Machines) and it'd be nice to have that kind of space again...
Anyone have any suggestions? If I have to I can swipe my girlfriend's newer LCD display to try a different monitor, but it'd have to be returned before she wakes up.

I just tested with my Sony 3D display. The moment the HDMI cable was plugged in, "clone" mode was activated.
The HDMI port is quite deep, so make sure the HDMI cable is all the way in. The last centimeter or so is really stiff, so it may not be all the way in. The plastic shell of the HDMI connector should be flush with the case.
←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗
Tap that kudos button if I helped ^^
←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗←↑→↓↘↙↖↗

Can't detect second screen on macbook pro

I have a macbook pro and when i plug in the vga adapter to my computer it doesnt work, but it does work with other computers.

Sorry i was frusterated and just said that.
I have a 15 inch macbook pro from late 2009
I have the mini display port VGA adapter going to a VGA cord going to the tv. I know the cords work just fine because they worked on another computer. The problem is when I go to system preferences<displays and click detect displays, nothing happens. My computer wont even recognize an outside display.

After working fine for several months, my iPhone 5 has started dropping bluetooth connectivity for 2 to 5 seconds at a time with my Sony MDR-1RBT headphones. The headphones work fine with other devices. I haven't moved to ios7 yet. Any ideas?

After working fine for several months, my iPhone 5 has started dropping bluetooth connectivity for 2 to 5 seconds at a time with my Sony MDR-1RBT headphones. The headphones work fine with other bluetooth devices. I haven't moved to iOS7 yet. Any ideas?

What user troubleshooting have you done on the phone? The steps are restart, reset, restore from backup, restore as new. Understand that a restore will put the latest iOS on your device. It is also possible there is a hardware fault on the device and the Bluetooth is failing. Anything is possible given the scenario you describe.
And as far as iOS 7.x is concerned, we have 5 different iPhones here at home, all with the latest iOS, a 4, 4s, 5c, and 2-5s and all are working just fine. So, a blanket statement such as the one provided by the other poster is not completely true. Others are not having any issues at all either.

Camera can not be detected! any ideas?

i am programming a microsoft which just likes NetMeeting,and i have a problem now.this question might seem silly to you ,but i am a new jmf_er,so i need your help!
to detect camera ,i wrote the code as follows:
Vector list = CaptureDeviceManager.getDeviceList ( null );
if ( list != null )
for ( int i=0; i<list.size(); i++ )
devInfo = (CaptureDeviceInfo)list.elementAt ( i );
name = devInfo.getName();
System.out.println(name);
if ( name.startsWith ("vfw:") )
System.out.println ("DeviceManager List : " + name );
capDevices.addElement ( new MyCaptureDeviceInfo ( devInfo ) );
but i discovered that there is no name starts with ("vfw:")!and the camera can be detected when i use another microsoft !
i do not know what is wrong ,
any ideas are welcome,thank you!
Regards
Adigan

The ist thing is that ur code is incorrect
the last statment (addElement)is not meant to be here
use the following code..
CaptureDeviceInfo devInfo=null;
Vector list = CaptureDeviceManager.getDeviceList ( null );
if ( list != null ){
        for ( int i=0; i<list.size(); i++ ){
                          devInfo = (CaptureDeviceInfo)list.elementAt ( i );
                      String name = devInfo.getName();
                      if(name.startsWith ("vfw:")){
                           dExist=true;
                                                                         break;
     if(dExist==true){
               MediaLocator m = devInfo.getLocator();
                DataSource ds = null;
     try {
          ds=Manager.createDataSource(m);                                Player player = Manager.createRealizedPlayer (ds);
                   player.start();
                    Component videoScreen= player.getVisualComponent();
          Frame frm=new Frame();
          frm.setBound(100,100,300,300);
          frm.add(videoScreen);
                                          frm.setVisible(true);
     } catch (Exception e) {
else{System.out.println("no device exist");}

BlackBerry Z10 Second can't detect Sim card

Hi All
I just bought a Blackberry Z10, secondhand from people I met from Internet
The Blackberry is still kinda new, used only for a month. And I got it pretty much cheaper
But the problem is, this Z10 can't detect sim card (yes the previous owner been telling about this before. She said its happened after she's upgrading the software)
So, I bought it, and re-installed the software (10,2 - 10,3 - even back to 10,1) still not working.
I'm trying to search the similar issues on Google, and found that it possibly because the simcard reader is broken
I check the simcard reader, I'm not really sure, but yes, seems there one pins missing on there. I saw only 3 pins on my Z10 simcard reader. Haven't seen any other Z10. Would you mind to check your Z10? How many pins on there?
And also, does the warranty will cover this issues if I claim it? I mean, it seems because human-error (previous owner might put the sim card not really carefully).
If not, how much it cost to fix it and change the simcard reader part? Well think I'm not gonna gambling anymore to buy a cheap gadget in the hope I can't fix it by myself
Thank you for help!

Hi Aliarroughi
Z10 I have a 3 sim card reader. there seems to be damage to your z10 sim card reader. try to correct the sim card reader price only $ 25
Ades Ganteng

Vista can not detect my graphic card ATI HD2600 on Satellite A210-128

Hallo,
Can someone help me with this issue?
I have a Toshiba Satellite A210-128 laptop with vista separately on DVD, but it seems that the dvd is damaged and I can not use it any more.
I have installed on my laptop a brand new Vista from the original DVD that Im using it on my desktop, but the problem is that vista can not detect my graphic card hd2600.
So Im stuck...... I tried to install the ati driver from the Toshiba update site but I get a error because ccc can not detect a graphic card ?????/
What to do????
It is something special with the DVD that i have from Toshiba ?????
Thank you very much.

Hi
> I have installed on my laptop a brand new Vista from the original DVD that Im using it on my desktop, but the problem is that vista can not detect my graphic card hd2600.
So Im stuck...... I tried to install the ati driver from the Toshiba update site but I get a error because ccc can not detect a graphic card ?????/
The whole issue is really mysterious. In my opinion there are two options;
Either your have used and tried to install a wrong graphic driver or there is something wrong with your GPU chip.
Are you 100% that you tired an right graphic driver from the Toshiba European driver page?
If yes, then I recommend contacting the ASP in your country because this could be really an hardware issue.
Furthermore I found you second posting in other thread
http://forums.computers.toshiba-europe.com/forums/message.jspa?messageID=142621#142621
and I think more and more that this must be an graphic card issue.

Can anyone guide me to ideas on basics of parallel processing in SQL

Hi all,
Can anyone guide me to ideas on basics of parallel processing in SQL and its usage in the the performance tuning of the query. If so what's the syntax to be followed and how to arrive at the optimized query after tuning

My 2'c on the subject.
Don't break your head over parallel query (PQ) processing. It should be something that is of concern to the DBA/Oracle architect - not the developer.
Yes, it is good to be aware of how it works. But you should not write hints in your code that forces PQ processing.
Simple example. You use hints to force a PQ of degrees 5 (meaning 5 PQ processes will be used). It works great on development. In production, 10 users are running that query round about the same time. The PQ ceiling is 20 PQ processes. The 1st 4 users each gets 5 PQs processes and the remaining 6 get none. Or another developer did the same thing, only he was very greedy and coded a PQ of degrees 20 into his SQL. So his SQL is now consuming all available PQ processes. So how did forcing PQ in your code addressed performance? It did just for a couple of users with the majority of users now facing even worse performance.
The DBA is the one that should be tuning this. He/she can set the degree of PQ per table. Control the size of the PQ etc.
And it does not stop there. The primary reason for PQ in Oracle is to lower the latency of I/O. Let's say Oracle needs to reads 100MB worth of data (full table scan or fast full index scan for example). It uses multi block (sequential) reads to read bigger chunks at a time. Still, a single process can only read I/O so fast - the speed of which is entirely dependant on the I/O subsystem and hardware.
Using a second process to assist with the I/O can reduce the overall time. Instead of 1 process reading 100MB data, there are now 2 processes only having to read 50MB each.
But as I mentioned, the actual I/O thruput is a lower level function. Let's say you start a 100 processes. Great - each only have to read 1MB worth of data. Response should be fast.
Wrong. Those 100 processes seriously overload the I/O subsystem and throttle it so badly that the complete platform's performance is degraded severely. So instead of these 100 process speeding up I/O performance, they trash the performance of the entire platform.
Sure, this is an extreme example. But the basic concepts are usually illustrated much better using such an example.
So, you as developer deciding on just whether to use PQ and just how many PQ processes to use...? Wrong. It is not your decision, not your area of responsibility and usually not your area of expertise.
Know what PQ is. Know how PQ works. But think long and hard before forcing PQ via your code (using hints) on a production platform.

Z1 - can't detect the SD card

Hello,
I just received a Z1 (6903) with the latest Android OS update (5.0.2) Update 14.5.A.0.270 and It doesn't detect any SD card when I insert them.
I tried 3 different card - 2GB, 8GB and 16GB (micro SD and micro SDHC) - Fat32 and even exFat format but the phone can't detect any of them in Settings - Storage or with a File browser.
In other phones or PC they all work fine, just this phone has the problem.
Any ideas would be highly appreciated.
Thanks!

@razvanst
Try again, if it doesn't work, contact your local Xperia care as it could be a hardware issue.
http://support.sonymobile.com/global-en/contactUs/
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Can not detect wireless card

WRE54G / Win XP SR2
My laptop and PDA can connect to the network wirelessly with no problems.
Trying to connect my WRE54G to my network. On every attempt at AutoConfigure nothing happens. Have disabled router security and 'SPI Firewall' (whatever that is). Still nothing. Have disabled router security and 'SPI Firewall' (whatever that is), and McAfee Firewall. Still nothing. I have moved the WRE54G to within ~4 feet of the router and tried everything again. Still nothing.
I have tried Setup but when I hit 'Next' I get the popup "Can not detect wireless card."
Have tried a reset and have unplugged/replugged the WRE54G. FWIW, the WRE54G 'Link' light blinks blue once for about a second and turns a constant red. The 'Activity' light blinks blue twice quickly about every 5 seconds. Nothing on my PC shows any response.
What is the wireless card that can't be found? The WRE54G?
How do I resolve this?
33#44

this worked for me too. Although I was never able to use the cisco install wizard successfully. I am using WEP security on my access point. I took the following steps.
1. From laptop, connect to network wirelessly with WEP security settings in place
2. From laptop, open browser, go to: 192.168.1.1, select wireless security, disable wireless security
3. From Range Extender, hold auto-configure button. It took me multiple attempts (~5) and it connected so the 'Link' light changed from red to a consistent blue.
4. From laptop, disable security for the access point (via control panel, wireless network connection settings)
5. From laptop, connect to wireless access point (via control panel, wireless network connection settings). test internet connection. Internet should work.
6. From laptop, access range extender web utility. open browser, got to 192.168.1.240, enable security, input desired WEP security settings/passphrase.
7. From laptop, enable wireless security for the access point. from browser, go to 192.168.1.1, select wireless security and enable it. use the same settings from step 6 (from the range extender).
8. From laptop, update wireless adapter settings to connect using the same security settings (eg. passphrase) from step 6/7.
range extender, access point and wireless adapter/laptop should all be connected.

Win7 on dv6t can't detect Toshiba projector

I have a Pavilion dv6t-2100 (WH770AV) running Win7 Pro 64-bit, trying to detect a Toshiba TDP-T9 projector. When I first connected it, it worked perfectly as I previewed a presentation. Then I moved the laptop and projector to another room, and now the laptop "can't detect projector" no matter what I do.
When I connect the VGA cable between the laptop and the projector, I hear the tones of connection from the laptop, but the laptop screen goes black (no matter which setting laptop is on -- (computer only, duplicate, extend, projector only) -- and eventually I get the message "can't detect projector". The projector continues to cycle looking for input, and cannot find anything.
I am considering getting a new driver for the NVIDIA GeForce GT 320 on the dv6t, but won't until I hear if others have had this problem and have resolved it.
Thanks!

You should post your issue on the laptop forum.
Does the NVIDIA Control Panel should see the second device? Look under setting up for dual monitors. The keyboard also has a video display rotate key function (LCD, LCD off and both).
You can also try a video driver update from the NVIDIA web site.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Why is the BIOS can't detect the HDs installed on IDE3 or IDE4 automat

Why is the BIOS can't detect the HDs installed on IDE3 or IDE4 automatically?
Theoretically, BIOS is supposed to be able to automaticaly detect all HDs on the IDE interface, including RAID, isn't it?
From Windows, I can find my SCSI interface is enabled indeed, but not finding my HD on it.
Besides, if I need to make RAID0-1 by software, then I prefer to install them by Windows 2000.
Why bother to install another software?
I think the performance of RAID installed by the software is quite inferior than the one installed by the hardware.
Therefore, I don't think MSI will design some function like that.
What's more, While rebooting process, I press the CTRL+F, trying to get into the RAID BIOS, but nothing happened.
Is it possible that the BIOS is crashed? ?(

The chip for the raid controller supplies its own bios for IDE3 and IDE4. The only thing the main bios has to do with that part is enabling raid controller. During boot does the screen ask you to press CTRL+F.

DVD-Audio and "can not detect sound blaster card" with Audigy2 Va

I recently purchased an "Audigy2 Value" card from an eBay user, because I recently purchased some DVD-Audio discs. I downloaded the Audigy2 drivers from the website, and the Creative MediaSource player. 5. Surround sound worked fine for me, though sometimes the driver would reset to the default 2/2. sound and I would have to re-select 5. sound, which was annoying.
Then I was completely unable to get the MediaSource player to recognise my DVD-Audio discs, and the EAX functionality of the player would never work. The EAX logo never appeared in the player. When I tried installing the MediaSource player from an install disc, I got the message "can not detect sound blaster card". Then I discovered the world of EEPROM problems.
I followed advice from some other threads, including using ScanPCI to get information on the card, which yielded the following result.
When installed on my machine (Asus A7A266 motherboard) the ScanPCI reads:
Vendor 02h Creative Labs
Device 0008h Unknown
Command 0005h (I/O Access, BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 00h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 0002h Unknown
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 0000A800h
System IRQ 5, INT# A
New Capabilities List Information :
Power Management Capabilities
Supports power state D2
Supports power state D
Current Power State : D0 (Device fully-operational, no power saving)
On another machine (specs unknown, it's a "house pc") I got this (with 3 entries!):
Vendor 02h Creative Labs
Device 0002h EMU0K Audio Chipset (SB Li've!)
Command 0004h (BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 04h, Header Type 80h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 002002h CT4850 SBLi've! Value
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 00009000h
New Capabilities List Information :
Power Management Capabilities
Current Power State : D0 (Device fully-operational, no power saving)
Vendor 02h Creative Labs
Device 7002h PCI Gameport Joystick
Command 0004h (BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 0h, Header Type 80h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Input, type Other
Subsystem ID 002002h PCI Gameport Joystick
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 00008800h
New Capabilities List Information :
Power Management Capabilities
Current Power State : D0 (Device fully-operational, no power saving)
Vendor 02h Creative Labs
Device 0008h Unknown
Command 0004h (BusMaster)
Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
Revision 00h, Header Type 00h, Bus Latency 20h
Self test 00h (Self test not supported)
PCI Class Multimedia, type Audio
Subsystem ID 0002h PCI Gameport Joystick (Guess Only!)
Subsystem Vendor 02h Creative Labs
Address 0 is an I/O Port : 00008400h
New Capabilities List Information :
Power Management Capabilities
Supports power state D2
Supports power state D
Current Power State : D0 (Device fully-operational, no power saving)
(Just a note: above you can clearly see that it does not say I have an Audigy, it thinks it is a SBLi've. Is this normal? The card IS an Audigy 2, it says so on the card.)
So, I put the card back on my own PC, thinking this has fixed my EEPROM, but I get the same as before. Subsystem ID 0002h. And of course the install software will not detect the card.
I realise that I could go back to using the web drivers, but this still leaves me with MediaSource not recognising the card and not enabling DVD-Audio or EAX, which is why I bought the card in the first place!
I have heard that the VIA chipset is possibly to blame for the EEPROM problems on the Audigy cards, and certainly it seems like it is not permanent, since it gave different information on the other PC. So now I am seriously considering getting a new motherboard.
Do other motherboards cause this same problem? I don't want to buy another board and get the same trouble. All I want is to be able to install my MediaSource and have it recognise my card so I can listen to my DVD-Audio discs.
Cheers,
Russ.

Figured out my problem. Installing the drivers from the web to begin with was a bad idea. They just did not work properly with the card.
The "card not found" problem has gone as well, after installing it in another PC. I am also using the proper install disc now, as the other one I was using turned out to not be for the Audigy 2 value after all, but was an Audigy 2 install disc. That easily explains the "Card not found" error. The differing results from the ScanPCI program are still bizarre, though.
Thanks to all of the people on the forum who posted information in other threads to help me deal with this issue. For now I am sticking with the original drivers from the disc and I am not upgrading.

MOVED: Can't detect second piece IDE hardware

Similar Messages

Maybe you are looking for