MOVED: HELP! My 2011 MSI P67A-GD65 (B3) build suddenly refuses to boot

This topic has been moved to Intel Core-iX boards.
https://forum-en.msi.com/index.php?topic=171555.0

Quote
On a slightly different topic...would it work (I have never done this!) to take my OS HDD and boot it on another PC? I am thinking this would not work because of system files and etc., but I have always wondered this and now would be the best time for me to know
It mostly works if the components used aren't too special. As you have no RAID setup it should work. However you will need to reactivate Windows once it made it. Of course you will also need all drivers for the new machine. Be aware that you might not be able to connect to the internet before you installed the proper driver for the ethernet adapter.

Similar Messages

HELP! My 2011 MSI P67A-GD65 (B3) build suddenly refuses to boot

Hello, I am new to this forum because I hadn't had any troubles yet.
I built my system in July/August 2011. Here's what it has:
MSI P67A-GD65 (B3)
Intel Core i7-2600K Sandy Bridge CPU
16GB Corsair Vengeance 240-pin DDR3 1600
650w Corsair Enthusiast PSU
MSI N460GTX Cyclone 1GD5/OC GeForce Graphics Card
1x 2TB Hitachi 7K3000 7200RPM SATA 6 GB/s (With Windows 7 64-bit installed)
2x 3TB Seagate 7200RPM SATA 6 GB/s (For storage)
I have used this computer for graphics and video editing...it has served me faithfully. Yesterday evening while editing a Word document, I got "do you want to save your changes before exiting?" and of course I said yes. Then to my surprise my computer proceeded to shut down and reboot. At first I thought maybe I missed a Windows Update message telling me it would reboot in xxx minutes so I was not alarmed. But then as I watched it reboot, it gave me the POST message that there was no disc drive recognized. I thought that was weird since I never noticed it before. But then after the BIOS screen with the MSI graphics thing I was faced with a blank screen except for a flashing cursor two inches from the top of the screen. When I realized that this wasn't going to leave, I got a bit worried so I did a reset through my tower's button and same thing happened...I unplugged everything and let it sit for a few minutes... restarted 10 minutes later....same thing. Did it again and then went into my BIOS to look around. It showed no HDD's connected and I had 3 hooked up. I was concerned my HDD went bad so I connected it to another pc and accessed it with no trouble as another storage...I was happy my files are all there. So then I reconnected to my original build and got the same POST message, but this time the drives were visible in BIOS....but still no boot.
I have another blank SATA HDD so I removed all my HDD's and connected it by itself along with my SATA DVD drive and I tried to do a clean Win7 install on it. But at the point in the install process where it asks WHERE you want to install Windows, no drives showed up. So that door was closed. I tried the same thing again after swapping SATA port locations, thinking 1 was defective, but I got the same treatment from all of them...nothing recognized during the install process, although the drives are showing up in BIOS....
I think I know why the POST message is saying 'no drives detected,' though...I read it is saying that based on the SATA ports being used...I have 8 SATA's on my MOBO...4 6gb/s; 4 3gb/s. 7-8 are 6gb/s and ONLY when I have a HDD plugged into one of them does it show on the POST screen...which I still think is weird, and seems to have just started happening last night with the rest of the problems...but I could live with that since I could disable the message in BIOS I think.
But I have tried to clear the CMOS...all three ways...jumper, button, battery. I reset BIOS thru BIOS.... Nothing changes. BTW, in BIOS I ran a RAM memory check and it passed. Besides, I am not hearing any weird beeps...related to that....
I don't know why this would happen after working perfectly for 2 years... And why would it politely shut down in the beginning of the process anyways? I mean...I appreciated being asked to save my changes...but I don't know what else to do...PLEASE OFFER SUGGESTIONS...any help is appreciated.
Thank you in advance...I hope someone can help me! I am still covered by warranty...but I want to do this right.
Thanks!
Marie
EDIT: BTW, I have also tried unplugging everything from the pc except for the DVI and power plug in case that was interferring....

Quote
On a slightly different topic...would it work (I have never done this!) to take my OS HDD and boot it on another PC? I am thinking this would not work because of system files and etc., but I have always wondered this and now would be the best time for me to know
It mostly works if the components used aren't too special. As you have no RAID setup it should work. However you will need to reactivate Windows once it made it. Of course you will also need all drivers for the new machine. Be aware that you might not be able to connect to the internet before you installed the proper driver for the ethernet adapter.

MOVED: Overclocking on the MSI P67A-GD65 (B3)

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=147494.0

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=147494.0

Random lock ups with MSI P67A-GD65 (B3). Please help!

Hello all,
I just built a new system with the following components:
MSI P67A-GD65 (B3)
Intel Core i7-2600K Sandy Bridge 3.4GHz
EVGA 012-P3-1570-AR GeForce GTX 570
G.SKILL Ripjaws X Series 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)
Thermaltake Black Widow W0319RU 850W ATX 12V PSU
Antec Lanboy air case
2X Western Digital VelociRaptor WD1500HLFS 150GB in RAID0 running Windows 7 Pro 64 bit
This was supposed to be my dream computer, but it has turned into a nightmare! It locks up constantly. Usually the mouse pointer will disappear and the computer will just freeze up. This normally seems to occur after the computer has been idle for a while. I have read that there might be compatibility issues with the MSI P67A-GD65 and the GTX 570 video cards. Can anyone confirm this? Any suggestions on how to troubleshoot this? The only thing event viewer is showing is the unexpected shutdown when I have to power cycle it. Thanks in advance!

Quote from: HU16E on 12-April-11, 11:26:00
That can happen, & it can really mess things up if two kits are attempted to be run together. The platform is DDR3 1333 as to native support by the CPU IMC. If the system can't run on 1333 RAM speed at CR 1, 9 9 9 24 @ 1.50v's, then something is wrong. No system should ever have to use an OC (or X.M.P.) as a workaround to make it work. That's why I recommended the Crucial 1333. Plug one stick in the blue primary dimm slot to get everything loaded & checked out, & go from there.
Exactly which SATA ports are you using for the HDD's & RAID? White Marvell or Intel SATA III, or the black SATA II?
Unfortunately, my local shop didn't have the Crucial, so I grabbed the Corsair instead. The Velociraptors are running from SATA 1 and 2 (the top white connectors). I also have 2X HITACHI Deskstar 2TB 7200 RPM 64MB Cache SATA 6.0Gb/s running in RAID0 from SATA 3 and 4 for storage (this computer is intended for HD video editing, compositing in After Effects, etc.). Sorry I forgot to mention that in the original post!

Problem with downgrading bios. MSI P67A-GD65 (B3).

Hi!
I'm having problems with downgrading my bios from version 4.3 to 1.19. I want to downgrade, because 4.3 doesn't want to boot when I use xmp settings for my RAM ( that might be related to my CPU since I have i5 2500k which is 32nm and 4.3 version of BIOS is recommended for 22nm processors ). When I try to flash with the MSI Forum HQ USB Flashing Tool I'm getting an error: "Rom file ROMID is not compatible with existing BIOS ROMID". I've ran out of ideas how to downgrade my bios so I'm asking you for help. My specs:
MOBO: MSI P67A-GD65 (B3)
CPU: INTEL CORE i5 2500K
RAM: G.SKILL RIPJAWS X 4GB (2x2GB) DDR3 1600MHZ CL6 (F3-12800CL6D-4GBXH)

Here you go. GD65 and GD55 usde the same BIOS files;
https://forum-en.msi.com/index.php?topic=179837.msg1295420#msg1295420

MSI P67A-GD65 Turning on and off

Hi ppl,
Well, the thing is like this, I bought a new gaming rig (specs after this chit chat XD) and everytime I start the system it goes on and off (just 1 Power Phase led on when this happens), even when I plug the power cable off the cpu the system will try to start again for the last time. The system turned on just 1 time and let me flashed the BIOS to v.1.7, after that I could start windows 7 without problems then rebooted to make sure everything was ok and everything went crazy again as stated before.
My specs are:
Intel 2600K @stock setting (how couldnt be at stock settings if cant ( ) start my system)
MSI P67A-GD65
Kingwin LZ 1000W (already tested on my cousin PC)
2x4Gb G-SKILL @ Stock Settings (already tried using a single module on all off the slots)
CoolerMaster V6GT Cooler
2x320GB Western Digital 6 Gb/s
CoolerMaster Cosmos S Case (already tried to turn the system on outside of the case)
Well this is it, hope I can get some help.
Thanks.
Edit: Removed foul language
Henry

djmx,
Stop the use of foul language disguised or not.
>> Please read and comply with the Forum Rules <<
Edit: How did you flash BIOS, did you use the forum tool or some other method?

Msi p67a gd65 with p67a gd80 beta bios

hi to everyone here,
i have purchased a pc and have a msi p67a gd65 mobo
i noticed that on the actual mobo it clearly states its a p67a gd65 i have verified this , its defnately a gd65
how ever, cpu z detects it as a p67a gd80, also command centre detects a p67a gd80, bios version is : P67A GD80 10.3b2
so my mobo has a gd80 beta bios...
i do not know how it came about as im not owner from new
question 1 : all i need help with is flashing back to gd65 bios (bios 1.19 ] , do i need to do a blind flash to force update ? and how do i do it ? because its gd65 not gd80
question 2 : and also how do i check if both bios chips were flashed to this beta bios ?
question 3 : do i flash both bios chips when i do the bios flash ?
question 4 : how do i switch between the 2 bios chips ?
sorry for all the questions, the main question is question 1
thnx guys

Quote from: PirateDog on 17-November-13, 03:50:12
In my experience, for a 2700k, UEFI/BIOS v1.H proved to be the very best one.
I would go ahead and use what P D says there, he did a lot of testing on his many builds the past few years and knows more about it that most other people.
What I had in my last reply was just the basic required info you needed to answer question about 2700K support after going through 1/2 dozen lists needed to find my info.

MSI P67A-GD65 VDrop Mod

Now I came across this modification for the MSI P67A-GD65 but I have no idea what this will do. Perhaps an adjustment for the VDrop (Vdroop?) voltage setting?
It's this mod posted on hwbot.org: http://hwbot.org/forum/showthread.php?t=22294
I'm not saying I want to apply this and perhaps ruin my motherboard or encourage anyone to do this, I'm just curious and wanted to share/discuss this with the people here on MSI HQ. Feel free to speculate and do any of the moderators/tech people have any idea what this does?
Happy modding

It doesn't state the origin, nor the real outcome (except a claim about VDrop ???), nor does it have any comparitive values, i.e. before and after. Not a very scientific way of approaching things. It just happens to appear in someones inbox. This post is March 2011 and no further comments since then ? I would be very careful.
Anyone attempting this, you are on your own. Let us know how daring you are and what your results are.

MSI P67A-GD65(B3) Configure 7.1 Channel

Hello Friends
So finally i bought MSI P67A-GD65(B3)
Its awsome board i always love MSI.
Can any one help me to configure my Creative 7.1 Channel Sound Speakers?
HOPE YOU GUIDE ME WELL AS BEFORE
Regards

From the manual:
Audio Ports
These audio connectors are used for audio devices. It is easy to differentiate between
audio effects according to the color of audio jacks.
- Line-In: Blue - Line In, is used for external CD player, tape-player or other audio
devices.
- Line-Out: Green - Line Out, is a connector for speakers or headphones.
- Mic: Pink - Mic, is a connector for microphones.
- RS-Out: Black (optional) - Rear-Surround Out in 4/ 5.1/ 7.1 channel mode.
- CS-Out: Orange (optional)- Center/ Subwoofer Out in 5.1/ 7.1 channel mode.
- SS-Out: Gray (optional)- Side-Surround Out 7.1 channel mode.
Obviously make sure 7.1 is configured in your sound options in Windows too.

Msi P67A-GD65 keep restarting after bios update

Hello
I have a Msi P67A-GD65 B2 motherboard, I tried today to upgrade bios to version 4.2,after update pc start up showing marvel controller then MSI logo and then computer restart over and over,if I try to enter BIOS will show 'entering setup', and restart again.Dual BIOS led does not light up and is not blinking.What can I do in this situation? How to switch the motherboard BIOS to boot from the other one?

Quote
Can you verify that, I don't think they make a B2.
Not sure why the hijack in this thread with different hardware involved, but a B2 is a defective mainboard from the beginning, and should have been replaced at the time of the replacement offers over a year or so ago.
Quote
I understood that there was a backup BIOS so I felt confident to be able to fall back in some way. Can you help me using that backup?
The Ivy udpate flashes the secondary chip as well on the GD65, so it would do no good to have access to it unless you could get into the UEFI/BIOS somehow to 'enable' the Dual BIOS Auto Update setting to restore the corrupted primary.

MSI P67A GD65 System Freezes while Gaming

hey
i m facing system hangs/freezes while gaming. it is all along working fine but suddenly problem arrises outta nowhere. mostly happens in Metro Last Light Game. i did change multiple things like 2 different rams stick, Bios are 4.1v (at default), i tried 2 different GPUs like 290 and 580 but stilll facing same issue. dont know why.
if you can help on it this, it would be alot appreciated.
m PC
MSI p67a GD65
I5 2500K
8GB RAM
800w PSU

What is the actual power supply?
Follow this >>Posting Guide<<
Make sure you run latest BIOS.
PS: Intel ME driver is crucial, without it system won't work properly, and that's why it didn't freeze anymore. Same applies to GPUs: if you have 400W power supply and want to run 2-way SLI, it will be fine until you install drivers, which make the computer and graphic cards recognise how much power they have and so on

MSI P67A-GD65 hard drive light always lit

I built a new pc with this motherboard a few weeks ago and everything is great except for the hard drive light. It stays dim 100% of the time and does show hard drive activity so i know it's working. I switched the connector on the motherboard to see if it was a polarity issue, but then it doesn't work at all. I even used a different LED that wasn't connected to my case and removed all the other connectors (power, reset, etc) and it still stayed dim. Lastly, i removed all the SATA cables from the motherboard, all fan connectors with no luck. I would appreciate any information on this, and if it's normal or if something is wrong and i should RMA the board.
PS - Bios version is 1.9. I never updated it cause everything has been working as it should.

Quote from: NovJoe on 30-May-11, 15:38:56
You should try the board out of the chassis. You may also want to try it in barebone conditions.
I tried that yesterday. Took it completely out of the case and left everything else off the board except for the ram and it still does it. Also used a separate LED to test that wasn't part of the case. In all the years i've worked on pc's, i've never seen this before. I guess at this point i'll have to live with it or buy another one and send this one back for RMA. I contacted MSI and they replied back with a suggestion to update the bios. This is going nowhere. While it probably won't actually hurt anything, i didn't spend $1500 on a new system to have problems with the motherboard.
Can someone help me test by using their MSI P67A-GD65 (B3) board? Disconnect JUST your power light from the motherboard to make sure no other light is interfering with the hard drive light, and see if it's still dimly lit at around 25% to 30% regardless if you're in the bios, or in windows.
Any help would be greatly appreciated at this point.

Serious gaming Question about MSI P67A-GD65

I really need to know for a fact, I mean really need to know. I play on getting 2 6990's and put them in CrossfireX. The thing is I see this board is 2 PCI E 16x but I see PCI E (16x, 8x). Does that mean the 2nd PCI E slot is running only at 8x? The sole purpose of having 2 6990s is to max out performance for the whole year. I see the 5970x2 lasted a whole year and is still faster than the 580GTX. I want to have 2 6990s to have superior FPS status for the whole year of 2011. Now if it's only 16x lanes for the top slot but 8x lanes for the last slot then will I see a performance loss of potential than if it was 16x on the bottom too?
MSI P67A-GD65 for 2 ATI 6990's in CrossfireX
If it's only 8x on the bottom then I cannot upgrade to a 2nd card. I see bench performance differences of 8x vs 16x with the latest cards of the day were massive. I can see how the cards of today would be even more massive.

Quote from: bobkn on 25-January-11, 11:04:00
The Maximus IV includes an nVidia NF200 PCI-E controller. Regular P67 boards only have 16 total lanes for graphics.
One thing I'm not clear on: the data rate with PCI-E on the P67 is supposed to be double that of the older chipsets. Naively, the data rate on a P67's X8 graphics bus ought to be the same as for one of the older X16s.
A pair of 6990s? Maybe you should have waited for Socket 2011. 40 PCI-E lanes, quad channel memory, 8 core CPUs, etc.
Perhaps the reason why they only have dual 8x and triple 8x not dual 16x or triple 16x. I think the NF200 chip is just a to make it look more expensive.
The last post in this forum the guy says it decreases performance.
http://forums.anandtech.com/showthread.php?t=237334
It adds more latency. I had an EVGA Killer Xeno Pro which is a hardware NIC for the PC. When I do head to head headshots on my screen in TF2 against another sniper it shows fire on my barrel but no kill or damage on the shooter after I die. Even with a ping of 20ms and the other guy had like equal or more. When I removed and sold it, everytime I see a flash on my screen and I'm lined up properly for the headshot with someone with equal or a bit more ping than me I always get the kill or at least damage before I die. I honestly thing adding more things was like the P4 architecture having long pipelines. The longer it takes data to travel the slower it will be and could be significant in performance loss. I'm going to have 2 ATI 6990's on my MSI board and see what will happen.

MSI P67A-GD65 infinite boot/loop problem

installed everything into my case and go to boot into the UEFI and nothing !
i press the power switch, everything starts fine and the fans spin up and the LED's on the board are fine, waits 5 secs then it shuts itself off and tries the exact same process again. it keeps doing this until i cut the power !
i've checked the 24pin etc, KB & mouse r fine, 2 different sets off RAM in every slot, cleared CMOS (i think).
seems like a very common problem with this board after a bit of googling !!
also tried
Quote
this is the 1st time ive used it !
tried the OC genie button on and off.
been sitting in the box unused for about 1.5 months. doubt that means anything tho.
put the stock cooler on securely, and still the same problem !
now tho, it wont start for about 3 secs after i press the power button
and
Quote
disconnected all the SATA's bar 1, and still the problem :/!
all the standoffs etc r fitted correctly and iv re-connected the 8 pin cpu and 24 pin. 1 stick off RAM in the 1st slot also :/!
checked no molex connectors r touching the case metal either
any suggestions?

motherboard: MSI P67A-GD65 (B3) bought on march 31st and used today for 1st time
CPU: intel core i7 2600K
CPU Cooler: tried an alpenfohn matterhorn with Scythe 1850RPM gentle typhoon Push/pull also tried the stock cooler
RAM Corsair CMD4GX3M2A1600C9 (2X2GB kit of 1600Mhz CL9 corsair dominator DDR3) and tried Patriot PSD34G1600KH (2X2GB kit of Patriot signature DDR3)
PSU Corsair TX650 650w psu
GPU XFX radeon 4870 1GB
Case NZXT M59 + mainly scythe fans and a noctua and coolermaster
DVDRW liteon DVDRW
Storage 128GB kinsgton SSDnow V100, 1TB Samsung F3 7200RPM, 1TB Hitachi 7K100 7200RPM all sata 3gb/s
Generic 5.25" fan controller
2 x 12" blue CCFL's
OS windows 7 x64 professional (installed on the SSD, but havent booted it yet as the board doesnt even get to BIOS :()
peripherals Microsoft reclusa keyboard and gigabyte GM-6990 (i think) mouse
monitor Benq g2222hdl connected via DVI
the only things i have changed today are, put the new notcua fan in my case, changed the Motherboard and CPU from and Asus M4A78LT-M & Athlon II X4 640 to MSI P67A-GD65 (b3) & intel core i7 2600k. Also, put the alpenfohn matterhorn on today.
everything is confirmed working apart from the CPU & Motherboard. everything worked yesterday, but i didnt have the necessary equipment to test the motherboard or cpu before using them together (today)
hope this will help

MSI P67A-GD65 and other 1155's whine

Hello MSI and community.
Recently I decided to build a PC especally for minimun noise.
I waited a long time for the B3 boards so I wouldn't have to go through the trouble of returns. Sadly this didn't work out.
First of all I ordered the cheapest and first mobo(gigabyte ph67-ud-b3) that was relesed. Soon as I plugged it in and Windows 7 got to boot screen (from the DVD) it started giving off a high pitched whine.
After alot of research I RMA it and ordered a Asus P8H67-M LX. Loaded it up and thought woohoo no whine, then as soon as windows finishes installing the drivers (first time on windows) of goes the whine again.
I RMA that 1 too and bought the MSI P67A-GD65 advertized as "whistle free" as well as people on another forum saying they didn't hear anything from theirs. This one does the same but I can't keep sending back boards for RMA and want to keep this one so I'm here hoping to try and resolve the issue with MSI.
I have tested these boards with Casecom 500w, ozc gamextream 700w, antec true power 650w and coolermaster pro m 600w with them behind a door to eliminate any fan noise.
MSI GPUS: 8800GS, 8800GTX and 560TI as well as onboard from the h67 board.
I've tried many differant BIOS settings, nothing but disabling C-STATE (fully disabled) effected it. (I havn't manually played with volts)
On the other 2 boards I noticed it seemed to dim when I unplugged all USB devices and in their BIOS it was c3/c6 I had to disable, MSI board doesn't whine as loud as the other 2 but it's more constant but with a morse code type theme to it which seems to be coming from CPU socket whenever the PC is idle, it's equally noisy from either side of the board. It's very annoying and accually gives me a headache as maxium distance.
Alot of people have said their 1155 board don't make a sound but 3/3 for me have so I'm not sure what to think.
I'm currently running with c-state disabled but Turbobooster only seems to go to 25% and slower clock speed on my i5-2500k and I assume for power usage, all things I don't want.
Can you give any information at all? Might it be possible to correct with a BIOS update? I'm open to any suggestions and will keep checking back here.
Hope you will be able to work with me on this issue.
Thank you in advance, I've prefered to go with MSI all my computering life.
Paul

Quote from: HU16E on 22-March-11, 04:18:14
Used the same CPU cooler on all three? That would be my wild guess.
I test it fanless of course but no I have used mutiple heat sinks aswell.
Quote
What's wrong with throttling down at idle or low usage? Who sits at a stop light with the engine at full throttle?
I'm not too sure what disabling C-state accually does but when running Orthos I saw speed was at 3.6ghz instead of the 3.3 while disabled.
Quote
Contact MSI Tech Support by opening a ticket & ask them. This is a user to user forum, being as such, MSI will most likely never read your thread.
Thanks, I didn't realize that.

MOVED: HELP! My 2011 MSI P67A-GD65 (B3) build suddenly refuses to boot

Similar Messages

Maybe you are looking for