MOVED: K7D Master does not recognize 1GB Reg ECC modules

This topic has been moved to Server/workstation.
https://forum-en.msi.com/index.php?topic=96220.0

How many modules are you talking about? If you try to use 4 of them, I can imagine it won't work.
Also, are they trouble free?
Try Memtest86 on each of the sticks.
I see this on the MSI product page:
Quote
• Supports eight memory banks using four184-pin DDR DIMM
• Supports DDR SDRAM DIMM
• Supports a maximum memory size of 4GB (registered DDR only)
Note: Because of limitations imposed by the personal computer architecture and BIOS, the user-accessible memory is less than 4 Gbytes even if 4 Gbytes of physical memory is installed.

Similar Messages

K7D Master does not recognize 1GB Reg ECC modules

I have an older K7D Master (2 CPU) which runs fine with 256 MB and/or 512 MB modules (all Kingston REG Ecc). The board also runs fine with 2 x 512 MB non ECC.
But when I use Kingston 1GB modules Reg ECC (KVR266X72RC25/1024) I get an error:
"AWARD Bootblock BIOS V1.0
BIOS ROM Checksum Error
INSERT System Disk ....
The modules don't work when only one is installed, nor when both of them installed, nor in any combination with de 256/512 MB modules.
I already use BIOS v1.91, I cleaned CMOS, installed another PSU (500W). All to no avail.
Doesn't the K7D master support the 1 GB modules? Or do I need other modules (brand/specs)? ???
Thanx.

How many modules are you talking about? If you try to use 4 of them, I can imagine it won't work.
Also, are they trouble free?
Try Memtest86 on each of the sticks.
I see this on the MSI product page:
Quote
• Supports eight memory banks using four184-pin DDR DIMM
• Supports DDR SDRAM DIMM
• Supports a maximum memory size of 4GB (registered DDR only)
Note: Because of limitations imposed by the personal computer architecture and BIOS, the user-accessible memory is less than 4 Gbytes even if 4 Gbytes of physical memory is installed.

DAQmx does not recognize NI 9213 TC module

Hello,
I am quite new to LabView and just tried to set up the system.
We are using a cRIO 9022 Real Time Controller with a cRio 9114.
DAQmx does recognize the Real Time controller but not the TC module (NI 9213) neither any other modules
(NI 9205, 9421, 9472).
Neither can I simulate these devices in DAQmx (V 9.0).
By the way, what exactly is meant by Real Time target?
Thanks for your Help
Patrick
Solved!
Go to Solution.

Hi Patrick,
The cRIO chassis is programmed with LabVIEW FPGA and the RIO driver and is actually not supported in DAQmx.
For some more information, I suggest following through Getting Started with CompactRIO and LabVIEW.
Best Regards,
John Passiak

MAX does not recognize PXI-4056 DMM module with PXI-1033 chassis

New to NI PXI chassis. Using the PXI-1033 chassis with several installed modules. I am able to see the chassis and two of the modules in MAX, but my PIX-4065(DMM) module is not listed/found. Any advice?

I have to ask the stupid questions first. Do you have NI-DMM installed in your computer? Is the DMM card fully inserted (I have seen people not lock the card in and expect it to work)?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

HT201302 I am trying to copy photos from an iPad to a Mac Air, but iPhoto does not recognize them Do you have to use PhotoStream to do this. Please forgive the ignorance, but we have just started moving to apple products and I know nothing about them. Tha

I am trying to copy photos from an iPad to a Mac Air, but iPhoto does not recognize them. Please forgive the ignorance, but we have just started moving to apple products and I know nothing about them. Do you have to use PhotoStream to do this?

How did the photos that you want to copy off get on the iPad ? To copy photos to your computer that were taken with the iPad, copied to it via the camera connection kit, or saved from emails/websites then see this page - on a Mac you should be able to use iPhoto, Aperture or Image Capture
To copy photos that were originally synced from a computer you will need a third-party app on your iPad such as Simple Transfer which can copy them off via your wifi network. But as photos are 'optimised' when they are synced to the iPad, any that you then copy back to a computer may not be exactly the same as they originally were on your computer.

I recently moved and had to disconnect my WD My Pro Edition II 2TB external drive I had been using for backup. Its been several months and now when i try to reconnect the external dire (Use a firewire cable) it does not recognize the drive is there. I a

I recently moved and had to disconnect my WD My Pro Edition II 2TB external drive I had been using for backup.
Its been several months (many upgrades to the iMac software during this time), and now when I try to reconnect the external dire (Use a firewire cable) it does not recognize the drive is there. I also tried "reloading" software from the Western Digital site, but after following all the instructions, it looks like my iMac doesn't support this software (I can't even locate it after I follow all the instructions.
Thnaks, for anyones ideas on how I can get this working again.....

First of all, you do not really want to use their software; if you want a bootable clone, use either Carbon Copy Cloner or SuperDuper. If you simply want to drag and drop some files, you don't need software to do that. The important thing on any external drive is that you format/partition it correctly (Mac OS Extended (Journaled) and using GUID partition scheme).
Unfortunately, I don't know anything about WD drives or their software, so I don't have any idea what kind of backup you did. Having said that, it should still recognize the external even if it's outdated. Have you tried mounting it manually in Disk Utility? If you can get it to mount, you could (worst case scenario) just drag your stuff off onto your internal and then reformat the external.

MSI x48c platinum does not recognize 2 PCIe boards

Hello,
I had the same recycling boot problem as others have noted.
It occured with the Antec Phantom 500 power supply and the Antec Signature 850.
Swtiched to a Cool Master Pro 650 and no more recyling boots.
However, I have 2 PCIe cards that this system board does not recognize in the POST (quick boot disabled) and no new hardware is found under win XP.
Boards are:
Black Magic Design Intensity (HDMI board)
http://www.blackmagic-design.com/products/intensity/techspecs/
United Audio UAD-2 Quad (audio DSP)
http://www.uaudio.com/products/uad/uad2neve128/index.html
Does not matter if they are together, alone or which PCIe slot.
These bpards are needed for my work.
anybody else have baords that the x48c can't see?
These same boards are fine with other motherboards.

i just remember i had once similar problem with a sata driver. the issue is this you can not adjust everything in bios in one go and expect mobo to know about it. what i mean is this for instance you disable the raid then you save it and exit and then when it reboot you go back to bios and reset another another parameter, you save and exit and on reboot you go back to bios and reset another parameter. i got round the prob that way and it worked and mobo saw the sata HDD. give this a shoot good luck and finally make sure raid is disabled
this is what i would do
1- make sure the jumper setting on your IDE Hdd is correct (Y may have to try this twice as there are two different setting on jumper setting for Master)
2- connect the sata HDD
3-click on power
4-go to bios and disable raid save exit
5-on reboot go back to bios
6--on first option click on it then you should see all devices that can be seen by mobo if you do not see sata HDD you have to click on enable for the auto to see the device once it sees the device save and exit. REMEMBER THE JUMPER SETTING ON IDE HDD CAN CAUSE PROB . SO try the other jumper setting for master, repeat this procedure once more hopefully you get it right

Windows Media Player does not recognize new downloaded songs

I have a Pavilion a4310f Prod Nr: AY014AA-ABA running Win 7 Home Premium 64 bit.
I just discovered that Windows Media Player does not recognize songs I recently downloaded from the Wal-Mart Music Download Site. The songs can be seen in the Music Library in a folder named "Downloads" and I can open each song and it will play when double clicked. The problem is that I can not create a playlist containing the new songs and burn a copy of the playlist because the songs are not listed in the Media Player library no matter hot it is sorted (Artist, Album, Genre, etc).
Any help/suggestions would be greatly appreciated.
Mitch
This question was solved.
View Solution.

You might also want to consider moving the songs to my Music or the folder you have WMP set as your Music folder. You can find/change that folder in WMP by going to File ---> Manage Libraries
Launch WMP ----> Tools ----> Options --->Privacy and be sure that the Display information from the internet box is checked.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Apple TV does not recognize my Apple account username (email) and password, but ITunes, my iPad and iPhone does. I have rest my password three times, same results. Also, ATV says my computer is not authorized, but I-Tunes says it is.

Apple TV does not recognize my Apple account username (email) and password, but iTunes, my iPad and iPhone does. I have rest my password three times, same results.
ATV says my computer is not authorized, but i-Tunes says it is.
I have i-Tunes open on my computer and have entered i-Tunes store, ATV says it can't access the store. Both on the same network!
I am so frustrated with this system! All these problems with Apple TV are not the end but the beginning.
In i-Tunes, songs are lost when they have not been moved. I lose whole albums I have ripped from CDs to iTunes
An audiobook book in two files are in the library but only one file is recognized by iTunes when I try to play it or transfer it to my iPhone

I Am having the same issue. Ie on the password issue.
I Am using a Macpro though.
i Have had no issues with the setup until recently.
However I think the hard drive is starting to fail as it keeps on losing the wireless connection and gas been stuttering a lot on playback.

Nokia 5610 does not recognize memory card

I have acquired a Nokia 1GB microSD memory card for Nokia 5610 d-1.
But the memory card is not recognized.
In Nokia 6303 the same memory card is recognized.
I have formatted them with this mobile phone.
Nevertheless, the 5610 (v10.00) does not recognize it.
I have taken out the memory card also several times and have started again.
What's wrong?

anyone?

Server does not recognize my recipients when sent as group.

I tried to send a group email and got the following message: "the gmail server does not recognize the following addresses..." followed by a list of names properly separated by commas. The list of addresses is so long, i can't see the bottom of it and i can't delete the offending addresses or delete the message i was trying to send. The message is frozen on my email screen (i.e. even if i force quit mail, when i reopen mail the message reappears). i have tried to trash it to no avail. i have also tried to delete the addresses from the bcc line and from the "does not recognize" message. i can highlight all i want, but nothing happens when i try to delete either by delete button or by "moving it to trash" This same request for support was posted in 2008 by marygh, but no answer was posted. I hope I have better luck. Thanks.

There's no commonality that I can see in the recipients' addresses...
The same thing happened with my previous ISP's SMTP (with my current setup), and since it didn't happen with my previous iBook / Panther setup (using the same previous ISP's SMTP and Mail groups), I figured it was a Leopard thing, but as I mentioned at the top, I found a thread in the Tiger-related forum with the same problem (but no resolution apart from making the groups smaller)...

Importer does not recognize already imported photos

Hello,
I have a really annoying problem with Aperture 3.0.3. The importer does not recognize already imported photos and wants to import them again and again. This is true for photos from my iPhoneand also for photos from my Nikon. If I enable "Do not import duplicates" then some photos vanish from the importer, when I the iPhone view is open. In the Nikon view not even one photo is recognized as already imported.
Also very strange is that when I have the iPhone (iOS 4.1 installed) attached to the Mac, Aperture opens the importer automatically and shows all photos correctly - but strangely, both iMac CPUs are at 100% until I click either "Cancel" or "Start import" or I disconnect the iPhone.
I tried the following without success:
- Correct permissions on media library
- Repair media library
- Rebuild media library
Imports from my iPhone last very long and seem to hang most of the time. I have to kill Aperture to make it work again all the time.
To me, it looks like there is something really messed up at the base of this program.
I have about 20000 files in my library - face recognition is not turned off - most of the preferences are at their default, I think. Did not play around very much.
Does anybody know what to do? I don't want to lose all my Projects (sorted all pictures into their own projects). But I want to work with Aperture again. When its working, it's a great tool.
Regards
Alex

I've had the same problem. For some things, like videos and photos on my iPhone, I've found as many as 5 copies of the images despite keeping the 'do not import duplicates' checked.
I've also found a bug with the import function, where if I'm importing from folders on my hard drive, sometimes it finds no images at all (even if they don't exist in my library). Simply cancelling and going back into import and the miraculously appear (including images that have already been imported despite having 'do not import duplicates' checked.).
I've been going through my library deleting all the duplicates, and managed to free about 10GB of space.
Having moved from Lightroom the 'technical side' of Aperture seems very antiquated. For example, if I remove a duplicate video - then try clicking on that video in Aperture, it literally takes about 10-15 minutes of spinning disc before Aperture becomes responsive. It also often hangs up on the 'updating previews' when I quit.
Such a shame aperture is so bad. I really like the functionality - eg. having my photos automatically sync with my Apple TV, but it seems to be absolutely full of bugs.

Adobe reader XI on xp does not recognize wireless network

upgrade to reader XI but can not connect to internet 'cause does not recognize access through wireless network

Good morning Michael and thank you,
Little introduction. Agronomist, family farming enterprise, 53 so I am not native digital. Want to put info on and about my work in the cloud, considering adobe and google, first trying to master it, later will need more services. Several laptops running on windows 7 and XP, connect via wi-fi on cable or 4GLTE; the problem arose in the xp platform in the adobe reader XI, as a stand alone, it displays message that can not connect to the internet, meanwhile the google chrome is up and running, I disable the PDF plugin of chrome, and try different ways on the matter but it was of no use. The problem is with adobe XI on xp, could be some sort of interaction with chrome, but unable to fix it, moreover, only your paid services has, as far as I could find out, have real support, but usually I go first to try and master the thing, and try it in order to see if I can manage the thing, but when I run into trouble could not find any help (besides this, that it is a help, but did not know the outcome from the start). In the other platforms operate well and I like it so far.
Best regards and a good 2015.
Roberto Tisnes
[auto-reply deleted by host]

Installed latest Adobe Flash - Incredimail does not recognize!

Installed latest Adobe Flash - Incredimail does not recognize!

Can you see the Flash animation at http://helpx.adobe.com/flash-player/kb/find-version-flash-player.html ?
If so, what version do you have installed.
Also tell us your operating system and browser.
[topic moved to Flash Player forum]

Moving Average Price does not get updated for Project Stock

Hello Experts
We have an Engineer-to-Order implementation for our client. Accordingly procurement is done per project. Each Project issues its PRs which are then converted to POs and recieved into Project Stock.
While assigning the material to the Network activity in Project (using material component) the system uses the price found in the material master (MAP or STD) as a planned cost appended to the project.
Problem:
while procuring the material, when we receive it into Project Stock (Mvt 101 Q + ) the Moving Average Price in the material master does not get updated. this way all newly created material master will never have a moving average price, thus whenever we try to assign them to the project we receive an error message (Cost for Material Component ###Mat.Num### cannot be determined.
Question:
How can I get the system to update moving average price (for all types of stock) based on procurement for project stock.???
Your help is kindly appreciated.

I'm sorry for the confusion
Case:
The T-code is CJ20N Project Builder in PS module
we are assigning material components to network activities under a certain WBS element in the project.
there is a function in the Project Builder to calculate the cost of a network. it uses the costing variant assigned to the network which is PS02 (We get the error here)
The costing variant has a valuation variant which lists a series of strategies to get the material price. Planned 1 if not then STD if not then MAP. (you can choose between many options via a drop down menu) you can choose 5 consequent options.
The MAP that the valuation variant is coded to get is the Plant Stock MAP -- Or the Project Stock MAP but only Per WBS element.
The MAP that the Actual postings update is the Project Stock MAP only Per WBS element.
This means that if you use a material component to purchase material 123 Acc.As. Q for WBS X for 10 $ then you try to assign a new material component with the same material 123 to WBS Y, the system will not get a MAP. because it's stored in QBEW per WBS element.
This way the system will never get the MAP right.
However, we don't always use project stock to procure for projects, for some requirements we can assign and use plant stock as well for Projects. that way we need the MAP from plant stock.
In the Valuation Variant you can use a User Exit Strategy. The user exit's name is COPCP005
My Suggestion is:
Use the User Exit COPCP005 to calculate the { Total value / the total quantity (MAP) from QBEW + Total value / total quantity (MAP) from MBEW } / 2
which is the MAP for both plant and project stock together, since that we are going to use both.
Q: Is this correct !?

MOVED: K7D Master does not recognize 1GB Reg ECC modules

Similar Messages

Maybe you are looking for