MOVED: [K7N2 Delta2-FSR] Unstable when DOT disabled

This topic has been moved to Overclockers & Modding Corner.
[K7N2 Delta2-FSR] Unstable when DOT disabled

Sorry! I've missed this section (overclocking&modding). So, You'll say the problem is probably RAM. I'll try to unplug one stick of mem and i'll see. I'll try flash the B30 BIOS If you say that it's most stable than b40 & b50. BTW. processor easly overclocking at FSB 200 and 1.700V - prime95; 8hour blend test; 0warnings 0errors!
About the PSU: On the beginning I have 400W Megabajt (megash#$) so I was afraid of the future of my device (mean: stuff, comp) and I was change it on ModeCom 350 (GTF). It's most, most, most, most stable than that megash#$.
PZDR [Take Care]

Similar Messages

K7n2 delta2-fsr and 2600+ Barton o/c problem!

Hi my system consist's of :
Athlon xp 2600+ Barton
k7n2 delta2-fsr ( B3 bios)
2*256 Twin Mos cl 2.5 Dual channel
GForce4 MX 440
ASUS 300w (+3.3V-> 28A, +5V -> 30A, +12V -> 18A)
The problem is that i can't go stable above 178 FSB whatever the Vcore is!
The cpu temperature seems to be low enough ( 38 idle)
With my previous mb i had reached easy 192 with the same processor.
The DOT is disabled!
Any ideas?

Quote from: BOSSKILLER on 27-January-06, 20:01:25
enable acpi.
set dot to default
set nvmm enabled
set fsb:ram 1:1
agp to 68mhz
nv/ati speedup leave auto
cpu interface set to normal
give nesesery CPU Vcore...
set DIMM Vcore at minimum 2.70
leave memory timmings to optimised if you dont know what to set.
start from memtest86 to be sure its memory probs. make sure there is no errors at test number five.
start increase DIMM Vcore if errors is detected till 3.0V its safe mobo is dimm is undervolted after 2.9V isnt give actual core what is suppose to be. let we know how its going.
make sure 1st that you dont have any memory fabric malfuction. this can be done by testing one stick then test other stick with memtest86.
at all i think that your CPU want more Vcore to be stable when you change FSB to higher. set CPU Vcore to 1.85V to be sure.(standart cooler can handle it) or best way is to lower multipler and set FSB to 200FSB to test memory if toyr CPU is unlocked.
First of all i'have already tested my cpu and the rams with my previous mobo,so unless this mb has a problem i should go up to 192fsb without any problem!
Now i can't understand why should i raise the Vdimm since the ram runs at lower frequency than the deefault?
Anyway i'll try all you say above and let's hope that everythimg will go ok!
Thanks

MSI K7N2 Delta2-FSR & Dual Memory Problems

Just recently I decided to upgrade my girlfriend's computer for her. Upgrade new PROC, MOBO, MEM. The proc is a AMD Athlon BARTON 3000+ OEM, Mobo is the MSI K7N2 Delta2-FSR and MEM is from PQI both are dual channel and in same package (identical) 512MB x 2. I thought it was an easy set up and everything and everything in terms of hook-ups was... I loaded XP and it gave me a crap load of errors, but I manage to load all of XP. Then came installing Adobe softwares, it kept saying "installing...." in an infinte loop and then froze on me. I skipped installing Adobe software and decided to install World of Warcraft Game. When I loaded the game, it popped up with errors installing, but it managed to install. WHen time to play the game; however, it kept crashing, restarting, and freezing. I noticed the system was a little bit laggy even though there was 1 gig of ram. So as a Geek Squad tech I am, I started to tweak and mess with it. I figure it was the MEMORY and I tried it and thought it was bad memory...
Yes it was memory when I tested with MEMTEST86 for dual channel ram, It came up with RED ERRORS all across the screen. So I decided to test each stick individually and each stick PASSED! I even tried each of the different slots on the motherboard and it all passed as SINGLE individual rams. I figure the first test with dual ram was just some mistake, loose RAM or something, so i decided to pop the DUALs right back in, in different combination and I kept seeing Red errors all over as well.
So my conclusion is :: Motherboard is bad. I contacted NEWEGG, but they will not refund my money as it has been over 30 days. I wish I would've known earlier... Anyways, So im stuck with exchanging for same mobo or find answers, but I think doing exchange will not do any good if this is a known problem.

Quote from: DaveR on 28-October-05, 01:38:08
Just to confirm; they are fine together in single channel, slot 1 and slot 2? Dual channel is purple + green slot, i.e slot 1 and 3 or 2 and 3. Or are you saying they can't work together in any combination of slots?
there will be a label on side of your psu stating max amps to +3.3V, +5v and +12v rails, i.e +3.3v = ?A, +5v = ?A, +12v = ?A. For example my psu is: Antec TrueBlue480: 30A/3.3V, 38A/5V, 28A/12V
Maybe your psu is not up to the job
You did load the chipset and graphics drivers didn't you?
You are correct sir... any combination of slots 1&3 or 2&3 will give error.... each as individuals 1,2,or3 will pass. The PSU amps readout are as follow:
+5v 40a Red, +12V1 16A yellow, +3.3v 35A orange, +12v2 18a yellow/black, -5v 0.5a white, -12v 0.5a blue, +5vsb 2.5a purple, pg gray.
I have loaded the chipset drivers from the CD it came with, and the graphics drivers are from ATI.com latest version. I will try and update the Nforce driver from Nvidia's site, but I don't see the chipset as the cause of this problem.
EDIT: In any combination of slots used, the read outof of MEMtest is single channel. Only slots 2&3 will have a read out of DUAL DDR channel 128bits. Slots 2&3 Will still have errors though...

K7N2 Delta2-FSR Won't Boot

Hi everyone,
I was in my bios cell settings and I believe I accidently changed my FSB setting from 166 to 200 with my multiplier set at 12.
My motherboard is a K7N2 Delta2-FSR (601-6570e-020) with a AMD Sempron 2800 and 2x512mb RAM. The system was totally fine before hand and now it won't boot at all. I can switch on the system and all the drives power up but my screen stays black with the amber light on and no post beeping. I have tried removing all my memory modules and when i boot with no memory, i get the long continuous beeps which signal "No Memory Present". When i install 1 module it doesn't post and doesn't beep at all.
I have tried unplugging my power cable from the PSU and tried resetting the clear CMOS Jumper to pins 2-3 for 15-30 seconds and then returning the jumper to pins 1-2. I have then plugged the power cable back into my PSU and then powered on the system but still i get the black screen. I have read on these forums about a "Safe Mode" jumper known as "J10" but my motherboard doesn't have this jumper. It only has the JBAT1 jumper.
Are their any other methods to reset my FSB to default or to reset the bios safely?
Will be grateful & appreciative for any help given,
Many thanks

Quote from: couttsey21 on 20-September-06, 07:43:58
All my fans are spinning, unfortauntely my motherboard didn't come with a D-Bracket so I can't test it out using that.
Any other suggestions?
well you can try without D-bracket also, just wait 5-6 seconds to ensure no boot or boot. ------> https://forum-en.msi.com/index.php?topic=96529.msg697033#msg697033

MSI K7N2 Delta2 FSR - memory issue

I've got MSI K7N2 Delta2 FSR and 512mb DDR400 Kingston Value Ram CL3. They work fine when I set them on a optimized settings and 166mhz. If I try any better timings then my pc wont be stable. I tried to set higher voltage, but nothing helps. I thought that I bought shitty memory, but when I set manually the same settins as optimized then my pc crushes. It isn't stable until I set optimized setting. Even if i set manually worse timings than optimized it will crush. I also tried with old TwinMos DDR266, witch was able to run with the best timings on my old MSI K7T266 Pro2(KT266A). I tried any other settings, but only optimized worked fine. So probably it is coused by motherboard, not memory. It has newest avalible bios and I installed newest nvidia drivers (also tried with old one, witch was on a cd bunled with mobo). Does anybody have a solution ??

I could get that RAM to work in Dual channel (even though their weren't matched pairs) at 2.5-4-4-8, synched with CPU FSB (1:1) at 200Mhz ... Like you said, pretty good bang for the buck. Although The Corsair I now have makes a difference (for 100$ more)...
System 1: MSI K7N2 Delta2-ILSR, XP2500 Barton (@2200Mhz)(11*200), Corsair TWINX 1024C2 (@2-3-3-6), XFX TI4200-128M (@300-590), Seagate 120G SATA
Western Digital 200G SATA, Antec Sonata 380W TruePower.
System 2: MSI K7N2 Delta2-LSR, XP2500 Barton (@2343Mhz)(11*213), Platinum 512M (@3-4-4-8), Powercolor 9600 Pro 256M (@550,460) Western Digital 160G SATA, Antec Sonata 380W TruePower.

K7N2 Delta2 FSR - no post

Ok....just got this board two days ago and installed windows xp pro and updates without a glitch. Then, I installed battlefield2 and played off and on for the rest of the day. Everything worked great ...until, right in the middle of battle, I got the blue screen of death but there was no text...just blue. I then restarted the computer and went into bios to check the temperature, which seemed fine. CPU was at 45c. Windows booted then i started the game again. I played for a while then BAM!!! blue screen again. Repeated checking temp and booted windows again. Started the game and as soon as it started, blue screen. So, I rebooted again. This time I got the award screen and it said "Bios Rom Checksum error. Insert system disk. Well, I do not have a system disk, so I turned it off and came to check here. I've read about all the things suggested like taking battery out, unplugging, pressing insert...blah blah blah. I also downloaded the newest bios and was prepared to flash it. But, the next time I turned it on, I got no post. CD drive spins up...hard drive crunches, fans turn on...but no floppy seek, no video, no beeps, keyboard freezes(i check by pressing caps lock and watch for the light). I am at a loss as to what would cause this, and have even submitted a help request, which says I will recieve a reply in the next couple hours...but have yet to receive such reply. I have tried ALL new hardware in this motherboard along with the originals in another motherboard....all hardware is fine...and other hardware makes no difference in this board. Help
Motherboard: K7N2 Delta2 - FSR
Revision: MS - 6570E Ver: 1.0
CPU: AMD Athlon XP 2500+ barton
Heatsink: Thermaltake Copper Plated
Fan: Silent Boost

It's hard to find out things, of course, what it is if one is not allowed to ask what the situation is. The BIOS message checksum error would suggest it returned to basic 100 MHz, which it didn't like. Why did it do that?
The processor is a 166(333) MHz. If you had not so good DDR400 RAM there might be problems, or if it was very fast. What RAM have you got? Or rather, did you have?
If you don't want questions, but something to do, I would suggest you stripped the system of all connected devices - including the power cable and power connections. Also take out the battery and the memory. Please study the memory real close. Go do something else for half a day or so.
Next with only the processor on reconnect only the PSU to the mobo, and have a test run for POST. Hopefully you'll get to BIOS, which will give you all kind of beeps.

K7N2 Delta2-LSR Unstable?

I have a K7N2 Delta2-LSR
AMD Sempron 3000+
Corsair PC3200 1GB 128x64 Value Select
SATA 80GB
On default the CPU is detected as a 1200Mhz CPU and with optimized it is corrected. I have fished through the boards and tried the following.
1. Bios flashed to 6570vB3
2. FSB 166x12
I have tried many things but the system is unstable. Most of the time when it detects the 3000+ it does not last very long and never long enough to install XP. That had to be done at 1200.
Where is B5 bios at? Acording to this I should be using W6570NMS.B50 but the best I can find is W6570NMS.B40 and the fourms suggest using W6570NMS.B30.
Any thoughts?
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=617&kind=1
My last guess is the memory, but I have none to swap out to test. Should I try something else and what?
Thanks

Could someone plz post (or PM me) the link to this new BIOS? I've been desperately waiting for this, because in all honesty the board sucks big time on previous BIOSes... only giving me problems no matter what I do.
I own a Galaxy 6600GT VGA (my PSU is 420W) and it would not run in 3D mode, or better said as soon as I run a 3D game the screen turns black althought the game goes on. Also my monitor used to randomly turn black with no image output as soon as Windows XP starts up, never to to show any video signals again. This was the case with the original B30 Bios, which is more stable than the B40.
To solve my "Monitor turns Black" problem I had to apply the unstable B40 Bios which would not allow me to OC even 1Mhz, and some times just freezes the board under 100% CPU load by some applications.
I know the "Monitor turns Black" issue was Mainboard Bios related because I had the same problem after trying the Inno3D 6600GT VGA, and only B40 solved it.
Now I need both "Monitor turns Black" and "Stability" issues resolved, before I decide to sweitch to another MB...
Working link to new B50 Bios would be highly appreciated.

K7N2 Delta2-FSR

I just brough a k7na2 delta2 fsr mobo i am having trouble with the lever i have try two socket A processors one amd duron 950mhz the other sempron 2200+ the mobo suports both processor but for some reason once i put the processors in the lever want go down it works find when ther are no chips yes i did have the gold arrow point toward the lever pivot but for some reason the lever want go back down. i am i doing something wrong or is the mobo just bad and i need to send back to mwave.com for replacement need help
thanks

you said the gold arrow was in the right direction. Iknow when i installed my AthlonXP+3200 it took alittle force to push the lever down, if i remember right it was in the begginning of the MB manual. on how to insall and precations Hope this helps DOK

MOVED: K7N2 Delta2 Conflict between AGP and Ethernet

This topic has been moved to Retired motherboards.
http://80.190.215.245/index.php?topic=103892.0

sorry, but K7N2 Delta2 series does not feature integrated VGA.
your board will actually be one of the K7N2G nForce2 IGP series
now, if you want help from us, you'd better help us by posting full details of your PC hardware (preferably in your signature, like mine) as well as all background info on this problem you can provide
(and then edit the subject of the first post to reflect the correct mobo)

MOVED: K7N2-Delta2-LSR modded bios?

This topic has been moved to Overclockers & Modding Corner.
K7N2-Delta2-LSR modded bios?

http://www.nforcershq.com/forum/bios-mods-for-k7n-and-k8-boards-vt55014.html

MOVED: K7N2 Delta2-LSR with XP-Mobile 3000+/266 FSB - settings?

This topic has been moved to Overclockers & Modding Corner.
K7N2 Delta2-LSR with XP-Mobile 3000+/266 FSB - settings?

I have the same motherboard, and from what I understand, your Athlon XP-Mobile 3000+ with 266 FSB will only run at 166. A AMD 3200+ with 400 Mhz fsb will run at 200 Mhz (with the correct memory). My board has an xp 2800 + with 333 fsb and the best I can get it is 166.
As far as overclocking, I don't know - I'm not brave enough to try (and I don't know enough about it).
Here's a link to the manual, if you look in the section about memory, it will give you the fsb possibilities.
manual link
If you can get more out of it, I would be happy to know!
Hope this helps.
jon

[nForce] has somebody MSI K7N2 Delta2-FSR + barton mobile

I wanted to know if there is a possibility of changing cpu ratio because msi kt4av did't see this cpu as mobile. on epox 8rda3+,8rda3+pro, and abit everything is ok. Has there somebody such mainboard with this cpu? Does mainboard seethis cpu correctly? And does somebody know if how to change the cpu ratio in barton mobile's bios.i wanna buy MSI K7N2 Delta2-FSR

Frequency/Voltage Control in BIOS
"CPU FSB Clock"
"CPU Ratio" (multiplier)
that is from KT4AV manual
mobile CPUs aren't properly identified on most boards, but that is merely a "cosmetic touch"

MOVED: K7N2 Delta2 OC problems

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=122072.0

Quote from: Henry on 04-December-08, 04:44:47
I would to just try it with only the A-DATA 1GB stick as I said before and see how it goes. You will never know if the problem is with the mixed memory or not unless you do this. Any way you look at it mixing 3 different brands & 2 sizes of RAM is not good! And then you OC on top of that.
Edit: If there was no problems before you started using the free sticks of RAM by the time you get done fooling with BIOS settings to get it working you probably have reduced the performance of your PC and gained nothing. How would you walk with a platform shoe on 1 foot and a regular shoe on the other foot? Not as good as with both shoes the same I bet.
when I used A-DATA 1GB the same probelm showed up.
When I do not OC , everything works fine...(games,prime95 etc)
So it is better said so: When i am walking, the both shoes feel fine, but when i try to run, there is probelm (maybe the shoes need new laces,or the heart is not strong enough and need some powerup ) so i just try to figure out where could be the problem and solve it.

Installing Windows XP Pro SP2 on K7N2 Delta2-FSR + AMD Athlon XP 2500+

I tried and tried to install the Windows XP Pro SP2, but it just doesn't work. I don't use the RAID with the WD 80GB SATA HD.
When the installation CD finished loading the required system files and "Starting the windows" in the blue screen, after than the system just hang there. Anyone who met this problem before? How to solve it?

The memory module that I am using now is Kingston PC3200 1GB DDR, I can't find the power supply details.
I just updated the newest BIOS to it and I don't configure the board to do any overclocking.
Just now I tried to configure any possible settings in the BIOS to make the system works, and I unplug the adapter for the mouse to use the USB port.
Guess what? It worked...
I hope it will keep working in the future, otherwise I don't know what I can do...

5.1 sound problems - k7n2 delta2-fsr

Hi I've got problem with my sound when starting games. when loading some games my 5.1 works fine in the intro music but when the game menu comes up it stops and goes to stereo sound. tried the new drivers from live update and still the same. Also should the settings in game need to be on software for the 5.1 to work because when I first got this board I'm sure in Battlefield2 I could have it set to hardware and it worked but now since I've been having the problems I have to have it set to software to get it in 5.1, as on hardware it just goes back to stereo.
Dont want to have to pay for a sound card when my board should support 5.1.
BTW I'm using the 3 jack plugs to connect to the board not the optical.

which audio drivers have you tried?
have you tried these yet?
http://www.nvidia.com/object/nforce_audio_4.62_win2kxp.html

MOVED: [K7N2 Delta2-FSR] Unstable when DOT disabled

Similar Messages

Maybe you are looking for