MOVED: K9N Neo V3 Won't detect video card
This topic has been moved to Linux/Unix.
https://forum-en.msi.com/index.php?topic=137985.0
Quote from: XrBob on 29-December-13, 14:23:50
1. The computer runs fine through the onboard video, I'm using it right now to type this. Is it possible that the computer runs fine even with a bent pin? Is it easy to tell if I have a bent pin?
yes it may run fine if a pin that connects to the PCI-E connector is bent! you need to remove the cooler and CPU and look in the underlying socket with a Bright light and a magnifier to see if they are all strait and in line! with each other from a few angles like from above and then at a 45 degree angle to make sure they all look exactly the same!
Quote from: XrBob on 29-December-13, 14:23:50
3. Does that mean having the motherboard just hanging outside the case?
put the board on a piece of plain cardboard or wood (to prevent shorting) on a table and plug up the power and so on and see if it posts there (most builders do that before they put it in a case or place it on the motherboard box itself)!
Similar Messages
-
Z87-g45 won't detect video card
I just got a 87-g45 and the on board graphics work fine with my dvi cable. I put in my gtx 660 but it won't detect it at all. I tried putting it in another computer and the card works fine. I saw another thread with a similar problem: https://forum-en.msi.com/index.php?topic=174991.0
I just flashed the bios to the one linked in the thread, but it didn't help. Should I plan to get a new motherboard or is there another way to solve this?Quote from: XrBob on 29-December-13, 14:23:50
1. The computer runs fine through the onboard video, I'm using it right now to type this. Is it possible that the computer runs fine even with a bent pin? Is it easy to tell if I have a bent pin?
yes it may run fine if a pin that connects to the PCI-E connector is bent! you need to remove the cooler and CPU and look in the underlying socket with a Bright light and a magnifier to see if they are all strait and in line! with each other from a few angles like from above and then at a 45 degree angle to make sure they all look exactly the same!
Quote from: XrBob on 29-December-13, 14:23:50
3. Does that mean having the motherboard just hanging outside the case?
put the board on a piece of plain cardboard or wood (to prevent shorting) on a table and plug up the power and so on and see if it posts there (most builders do that before they put it in a case or place it on the motherboard box itself)! -
Z77A-G45 will not detect video card.
I though that I was having trouble with a new gtx 760sc, so I RMA'd it. On-board video works fine. Still can't detect video card. Bought a new power as well(antec HCG-750). After i received the new video card and still had the same issues I tried out other video cards. Tried two different nvidia cards. One was a 4 series and one a 5 series. Tried in both pci-e slots, and yes the correct power cables were plugged in.
CPU looks fine.
Was finally able to breadboard the thing today. Had the same issues at first. Then I tried the third pcie slot and got post. This one is pcie2.0, so I tried the other slots again. Was able to get the 760 to boot on th second pcie slot. Put the mb back in the case and lost boot on card again. Reseated, same issue. Breadboarded and was able to get the card to post. Still no post in case. Can't see what could be causing a short. Rearranging the risers right now to see if is one of the risers causing a short, or maybe not enough clearance. Any other suggestions would be appreciated. -
H55m-e23 not detecting video card
Hello i recently upgraded my pc with new video card (asus engtx570 directcu ii gtx 570) the problem is that main board(MSI H55M-E23) is not detecting video card, so here is what happens when i turn the pc on it starts to beep 1long beep and 2 short beeps. First i thought it might be power suply so i bought new power suply with 700w and still the same thing happens, then i tryed with LC850w and same thing so i guess the power supply is not the problem. I removed rams and tryed with 1 stick, i have 4 different sticks and same thing happened with each stick. i tested the videocard on different mainboard (ASUS P5Q PRO and ASUS P8H67-M PRO REV. 3.0) and videocard worked fine. i tested my mainboard H55M-E23 with sapphire ATI HD 6950 and it worked too so the pci slot is ok, and now i dont know what to do more i tested all things possible. So what is the problem? my mainboard does not want to detect videocard (asus engtx570 directcu ii gtx 570) 3beeps ( 1long and 2 short) PLEASE HELP!
CPU: Intel® Core™ i5-760 Processor Clock Speed 2.8 GHz Max Turbo Frequency 3.33 GHz
Main Board: Msi h55m-e23 Bios: AMI BIOS Version 17.4
Video Card: Asus GeForce ENGTX 570 Direct Cu II
Memory: Kingston 1x2GB 1333MHz DDR3 CL9 DIMM 1.5V
Apacer 1x2GB 1333Mhz DDR3 CL9 1.5V
PSU: LC 850W Arkangel LC8850, 140mm FAN, V2.2
850W max., ATX V2.2, Free-Plug cable-Management, Active-PFC, 3 x PCI-Express, 4 x +12V: 60A, S-ATA,
+3,3V: 30A
+5V: 28A
+12V1: 18A
+12V2: 18A
+12V3: 18A
+12V4: 18A
HD: Seagate Baracuda 7200 - 320GB
Windows 7 x64
For the memory ( i did try with only 1 stick at the time... they go well together with my other card Sapphire ATI HD 6950) -
K9N Neo-F (non-sli) onboard sound card cant install winxp sp2
K9N Neo-F (non-sli) onboard sound card cant install winxp when ı install driver I see this device cant start (code 10)but first install working but now ıcant install sound device pls help me...
K9N Neo-F non sli nforce 550 motherboad
Asus X550HM pci-E vga card
Aopen HB600 400w power
Veritech 512 mb 800 mhz single ram
samsung 160 gb&250gb sata2 hddTried to uninstalled those driver again. ALso what NVidia driver are you using? Tried to used the latest drivers from Nvidia. What are the rails for +12V PSU in the labels? Gd luck.
-
MOVED: K9N Neo v3 nforce560 and Athlon 6000+ (Windsor 89W) voltage problem
This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=125583.0my configuration is like this:
..:: AeroCool ExtremEngine 3T ::..
..:: 2x1GB Geil 667Mhz CL3 DDR2::..
..:: Athlon X2 6000+ 3000@3135MHz (Windsor 89W 2MB CacheL2 1.35v) + Arctic Cooling Freezer Xtreme ::..
..:: MSI K9N Neo V3 ::..
..:: EVGA GTX260 Core216 55nm SC (626/2106) 35% fan speed ::..
..:: 2x250GB WD Caviar 16MB cache Nvidia Stripe Raid 0 ::..
..:: be quiet! Dark Power P7-Pro 550W ::..
..:: 22'' LG L227WT-PF 1650x1080::..
..:: Creative Inspire T7900 7.1 ::..
..:: WinXP Home Edition SP3 ::..
be quitet 550 should be enought for much stronger configuration -
My iMac won't detect any SD card's. It doesn't seem to matter the size (2GB-16GB) or brand, it is just like I haven't inserted one. I have never used one with it before so it isn't from failing to "safetly remove hardware" and I have tried cleaning the slot (with air can)
Have you checked to see if the SD card reader is listed in system profiler? (apple menu, about this mac, more info button) it should be listed under Hardware, under USB, it would be labeled some thing like "Internal Memory Card Reader".
If the card reader isn't listed:
Have you tried a NVRAM Reset?
Have you tried a SMC Reset?
If the card reader is listed, but your not seeing the inserted cards:
Have you checked to see if the cards are reconised in Disk Utility? (go to the dock, click on finder, go to the menu bar, click on the go menu, chose Utilties, double click on disk utility) Do you see the sd card listed? -
Detect video card in 32 and 64 bit.
How can I get both the 32 and 64 bit versions of CS6 to detect my graphic processor (AMD Radeon HD7700) for GPU usage in Win 7 ? Cuiurently, it is only seen in 64 bit.
Thanks again Chris.
I again completely uninstalled the AMD Catalyst and drivers and reinstalled the latest one from their site. I am still unable to select Again, the card is not detected in the 32 bit version of CS6 and is readily available in 64 bit. Also very interesting is what the System info shows. i.e. Windows XP and yet I installed the lastest version of CS after I had updated to Win 7 on a new computer.
Here's what the system info shows in CS 6 32 bitr ..
Adobe Photoshop Version: 13.0.1 (13.0.1.2 20130522.r.24 2013/05/22:21:00:00) x32
Operating System: Windows XP 32-bit
Version: 5.1 Service Pack 3
System architecture: Intel CPU Family:6, Model:10, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, HyperThreading
Physical processor count: 4
Logical processor count: 8
Processor speed: 3403 MHz
Built-in memory: 16344 MB
Free memory: 12841 MB
Memory available to Photoshop: 3255 MB
Memory used by Photoshop: 62 %
Image tile size: 128K
Image cache levels: 4
OpenGL Drawing: Disabled.
OpenGL Drawing Mode: Normal
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: False.
OpenGL Allow Old GPUs: Not Detected.
Video Card Vendor: ATI Technologies Inc.
Video Card Renderer: AMD Radeon HD 7700 Series
And here's what it shows in CS 6 64 bit version ...
Adobe Photoshop Version: 13.0.1 (13.0.1.2 20130522.r.24 2013/05/22:21:00:00) x64
Operating System: Windows 7 64-bit
Version: 6.1 Service Pack 1
System architecture: Intel CPU Family:6, Model:10, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, HyperThreading
Physical processor count: 4
Logical processor count: 8
Processor speed: 3403 MHz
Built-in memory: 16344 MB
Free memory: 13122 MB
Memory available to Photoshop: 14730 MB
Memory used by Photoshop: 71 %
Image tile size: 128K
Image cache levels: 4
OpenGL Drawing: Enabled.
OpenGL Drawing Mode: Advanced
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: True.
OpenGL Allow Old GPUs: Not Detected.
Video Card Vendor: ATI Technologies Inc.
Video Card Renderer: AMD Radeon HD 7700 Series
In my powerful mind, it appears that CS will only see the card in the 64 bit version. Not that it's a big problem with easy work-arounds but it puzzles me and I was hoping that someone else has had a similar experince and was willing to chime in.
Appreciate your time. -
Cannot Detect Video card (Radeon 6750m)
Dear sir,
I would like to know why my laptop cannot detect my video card (Radeon 6750m). It only shows the built in graphic card intel. I already try to use system restore and reset to original factory mode. It will appear but after updating my drivers and reboot my laptop. My laptop cannot detect again the video card.
Please help me resolve this problem,
for you reference
http://tinypic.com/r/2it67ex/8
This question was solved.
View Solution.You will have to enable the Radeon HD adapter by using the Catalyst Control Center.
Once you do that the adapter will appear in the Device manager.
If you are using the Intel HD graphics, only the Intel graphics will be seen in the Device Manager.
I know that may sound strange, but it is one of the pecularities of having a switchable graphics capable notebook.
The following URL goes to an overview of switchable graphics. Take a few minutes and read it. It should help make understanding it simpler.
http://support.hp.com/us-en/product/HP-Pavilion-dv4-Entertainment-Notebook-PC-series/5048648/model/5...
Do not instal the Intel graphics driver seperately!
Doing that breaks the switchable graphics feature.
Only install the HP ADM ATI graphics softpaq. It will install both drivers automatically and let you use the switchable graphics featrure og your notebook.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer -
10.4.7 won't detect EDVO Card
I purchased a Sprint Merlin S720 Mobile Broadband card. According to Sprint I had to initialize the card in a PC with Win XP then insert the card in my Powerbook.
The card worked fine in the PC, but when I inserted the card in my Powerbook it didn't detect the card. The card lit up and a card icon showed on the top bar next to my Airport icon, but when I click on it it indicates "Unknown Vendor". The only workable option there is to turn off the card.
When I go to "Internet Connect" application, or in Preferences "Network" there is no indication that the card is there. When I to "About this Mac" "More Info" the Hardware PC Card section shows vendor Unknown and the USB section of Hardware shows USB Bus, Novatel Wireless CDMA.
????????The Sprint 5740 card will work without a hack... on my powerbook g4 15", running 10.4.7, I had the same problem you had. Somewhere I read to use "#777" for the phone number in Network setup, use the actual card phone number for Phone Number, and the 6 digit NPA/NXX number from Sprint for the password. Select Sprint PCS Vision for the modem, and it's done. I couldn't believe it, after 4 hours of trying.
Powerbook G4 Mac OS X (10.4.6)
Powerbook G4 Mac OS X (10.4.6) -
Hallo i would like to post a problem when my computer boots up i get message using pcei gen 1then it says cant find device and then boots furtherinto
vga graphics mode i have a pce video card in pci 16 slot. I have in bios set as primary pce and internal video turned of .I hope someone can give me advice here are my specs taken with live update
Operating sys Windows 7 64 bit
Motherboardmodel 760ga-p43fx ms-7699
Curent Bios Ver 1.20
Graphics card standaard-vga adapter But i have msi hd 7750
Psu XFXpro 550Wat
I thank you>>Posting Guide<<
-
hello, my video iPod will not detect that a video is video and categorizes it as a music file, and when I select "get info" on the particular video, all the tabs (summary, info, options, lyrics, artwork) are all available except the video tab. I can't make my iPod detect a video if this tab is not available for selection. So how do I get the iPod to detect these videos and not play them as simply audio files with no visuals
basically my iPod puts all the videos in the audio playlist and I want to know how to get my videos out of the audio playlist and into the video playlist as none of them show up in the video playlistYou might want to try a different port on your computer. Also check with a different cable. I know I've personally run in to issues with a bad USB port, it will read a keyboard/mouse just fine, but if I try it with an external drive or iPod, nothing.
-
MOVED: K9N Neo V3 Chipset Drivers for Windows 7
This topic has been moved to Windows 7.
https://forum-en.msi.com/index.php?topic=123975.0i checked for usb legacy options. no such luck.
my next step will be to use the windows 7 sdk kit which comes with xperf, xperfview and xbootmgr. these tools should be able to assist me with doing a trace during the boot process.
however if my theory is correct.... the issue doesn't happen during the windows driver boot process but before....
so i will try to do a trace and see what it finds. but in any case, anyone have suggestions on how to do a bios memory dump? preferably while the system is still running or while it is frozen before the post screen.
i really really hate giving up on technical problems. my only other option is to either return the usb drive for warranty and hope i get a new drive with an updated firmware or buy a new usb drive... -
MOVED: K9N Neo V3: No overclocking with DualCore Center
This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=113264.0Could be board is dying check for swollen or leaking capacitors around the sound chip as those aren't solid (left upper corner above the three PCI slots).
Also try replacing battery for the time issues. -
MOVED: K9N Neo-F Flashable to Overclock
This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=101758.0This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=101758.0
Maybe you are looking for
-
Unable to start after Windows 7 Pro upgrade, am I crazy?
I'm now on my fourth try and I'm about to lose my patience. I purchased a T400 6475-B14 with Vista, 32 bit. I purchased a copy of Windows 7 Professional upgrade. I am installing the 64 bit disc. Currently the machine has 2GB of ram, but I ordered
-
Bit Locker Data retrieval forgot key and password
Hi All, I am using Windows 7 utlimate version and unfortunately i forgot my password and key as a result of which i cannot retrieve my data . Can anyone please tell how to recover data without using password and recovery key
-
JMenu Mnemonic in JApplet not working
Hi, Here is a code in my JApplet, but some how the Mnemonic is not working, why?? I m using jdk1.4.1 Ashish import javax.swing.text.*; import java.awt.event.*; import javax.swing.*; import java.text.*; import java.awt.*; import java.math.*; import ja
-
Startup Disk not recognizing Windows disk
I had a working Snow Leopard installation with Windows XP on a separate disk. Bootcamp worked correctly. I reinstalled Snow Leopard on the primary disk and now Startup Disk will not recognize the Windows disk, although holding down Option at startup
-
Hello, iam using the latest version of firefox, whenever i login into my yahoo mail account i get a stop script error, the details of the error script is mentioned below , please suggest how to stop this the website is www.mail.yahoo.com. i was getti