MOVED: Latency problem and potentialy linked Vista problem with K9VGM-V

This topic has been moved to Vista problems.
https://forum-en.msi.com/index.php?topic=107394.0

Like you already mentioned: you are using some beta-drivers which may cause some trouble.
Please verify that you installed the driversin the propper order: chipset drivers first (VIA-drivers that is, you can have a look at VIA's website to see if there are any VIA Drivers for Vista you can use. Install VGA drivers after that and the SB drivers last.
Just a tip: I recommend you have a look at your power supply unig. A 350W PSU with your hardware probably is not enough to run your system on. It even may cause your system to act strangely, like you just described.
How many amps on 12V rail?

Similar Messages

I recently moved to Australia and received a new iphone with a local AUS number. I have a backup of my US iphone in the icloud. Question: when I activate my new AUS iphone which option should I choose - new phone or restore from backup?

I recently moved to Australia and received a new iphone with a local AUS number. I have a backup of my US iphone in the icloud. Question: when I activate my new AUS iphone which option should I choose - new phone or restore from backup? I would like to have all my contacts, email, etc. however wasn't sure that option was appropriate since it is a different/new number and a new phone.

Yes, as new iPhone then restore from backup.

ITUNES HAS ENCOUNTERED A PROBLEM AND NEEDS TO CLOSE PROBLEMS

PLEASE HELP ME. I CAN NOT GET INTO ITUNES. I KEEP GETTING THE ERROR MESSAGE "ITUNES HAS ENCOUNTERED A PROBLEM AND NEEDS TO CLOSE" ERROR . WHAT MUST I DO? ITRIED TO REINSTALL THE SOFTWARE,BUT IT DID NOT WORK. HELP

First, try to check your Quicktime installation--this has been discussed over and over again on the forum. If Quicktime won't launch--that's the problem. You can uninstall and reinstall this application.
I just had this failure a few days ago. I chose to "repair" my Quicktime installation instead of re-doing the whole thing. I TURNED OFF MY VIRUS PROTECTION AND FIREWALL BEFORE I PROCEEDED! Then, I let Windows run a repair and everything worked properly afterwards!

"Itunes has encountered a problem and needs to close" problem.

Before you read anything, please understand that I am literally being driven to tears right now and that I am on the brink of insanity.
On Saturday, I tried to update my iPod with new songs and apps that I got from the iTunes stores since Friday. Itunes would open but in the next 10 seconds following it, the error window that says "Itunes has encountered a problem and needs to close" etc. came up. I let it go for like two hours, thinking it was a small bug or something, and I ran a virus scan too, just to make sure (I just switched to AVG too on Saturday). Two hours later, iTunes STILL wouldn't work and by that time, I was about to become upset. I uninstalled and then reinstalled iTunes about 5 times that day. Now today, iTunes is still giving me the same problem. I know other users have faced similiar problems but someway or another, they found a way to fix it.
I have tried EVERYTHING to fix iTunes. I even did a Quicktimes and an iTunes run to get rid of any and all files associated with the two programs. When I finally thought the nightmare would end, I downloaded iTunes again. However, not only did it NOT work but now EVERY SINGLE ONE OF MY SONGS that I had in my library were GONE. No traces, nothing. Even the movies that I had on it had vanished. Everything single thing that I bought in the iTunes store disappeared. Now, at this point, I am now both incredibly frustrated, and crying my freaking eyes out now. (Understand that I am 15 years old and I grew up with music as my only solace.)
Somebody, just please help me through this ****. All I wanted was to just update my iPod so I could listen to it in school, and now my music is gone, along with a dead iPod. -_-

I found my solution! In case you're still having trouble, here's what I did (please pardon the odd grammar, I copy-and-pasted this from another one of my questions!):
And for those of you who are still experiencing this problem, this is what I did. Although I don't know your details and your own specific problems, I hope this can be at least a helpful guide. (The solution was incredibly simple and easy that I am extremely mad at myself for deleting all of my files now...)
First, just for safety measures, run a virus scan and a malware scan (so you can get rid of those icky programs lurking in your computer). Once you're done with that, check to see if your computer has an update for you (those automatic updates you get that comes with every Windows computer). If you do, click on it and update your computer. Once it's done, restart your computer and VIOLA! Itunes is fixed, Quicktime is fixed, and Adobe Reader is fixed.
It's insane. I guess this just goes to show that even the simplest of things can fix such a mind-boggling problem! Before you take extreme and drastic measures, follow through with the simplest of solutions first!

After effects and premiere linked file problems

Premiere won't open after effects linked files, keeps crashing. (I haven't moved the files)
When premiere opens all the ae files are offline, I try to re-link them and premiere crashes everytime.
I have tried importig the ae files into pp without dynamic link, still crashing.
I am new to premiere from fcp.
Using imac, 10.7.5, 16gb, i7.

Are you getting an error message? If not, what is the last thing that the startup screen says?
It may be a problem with something in the preferences folder being corrupt. Try deleting the entire preferences folder and restarting. See this page for the location of the preferences folder.
It also may be that you have something running in your admin account that is blocking a port that is needed for internal communication for After Effects and Premiere Pro. See this page for more detail about that possibility.

I have been trying to download a free trial of Photoshop and Lightroom before deciding whether to buy. I have Mac 10.6.8 so it said my system requirements were no longer compatible. On the Community forum someone also had the same problem and two links w

[personal information removed... Mod - https://forums.adobe.com/docs/DOC-3731]
[This is an open forum, not Adobe support, please do not post personal information]

The answer is as John T Smith says - you need to meet minimums. Here lies an interesting thought for the future. When Adobe, as it surely will, decides not to support current operating systems, it will dictate when everyone has to update their computers because we no longer own the software so will in effect be forced to update at least the operating system in order to run the software. This is quite different from previous situation because we could then choose to keep an older version of PS that was indeed compatible with our existing computers. Wait for the outcry when it happens!

Problem connecting 6230 to Vista PC with Toshiba B...

Hello,
I recently got a new laptop with Vista installed. My 6230 used to connect well with my former PC (Win XP).
Initially I managed to have PC Suite (6.83) work once and downloaded my contacts to the PC. Then sync stopped working for contacts but other functions were ok. Suddenly my computer asked me to check the Bluetooth drivers (don't know what stack it used, probably Microsoft) that apparently were not recognised anymore. I upgraded (following instructions from Asus website) and got the Toshiba stacked installed.
Now PC Suite still "sees" the 6230 but cannot link with it. The 6230 doesn't prompt for a pin. Outside PC Suite, Bluetooth connection manager manages to have the 6230 prompt me for a pin, and connect, but it would disconnect after 2 seconds.
Has anybody experienced that sort problem ? Is it more likely to be Vista-related, or my driver is faulty, or the 6230 is, or is PC Suite ?
/discussions/board/post?board.id=connectivity#
Submit
THanks for your help

08-Apr-200712:09 PM
blason wrote:
Hello,
I recently got a new laptop with Vista installed. My 6230 used to connect well with my former PC (Win XP).
Initially I managed to have PC Suite (6.83) work once and downloaded my contacts to the PC. Then sync stopped working for contacts but other functions were ok. Suddenly my computer asked me to check the Bluetooth drivers (don't know what stack it used, probably Microsoft) that apparently were not recognised anymore. I upgraded (following instructions from Asus website) and got the Toshiba stacked installed.
Now PC Suite still "sees" the 6230 but cannot link with it. The 6230 doesn't prompt for a pin. Outside PC Suite, Bluetooth connection manager manages to have the 6230 prompt me for a pin, and connect, but it would disconnect after 2 seconds.
Has anybody experienced that sort problem ? Is it more likely to be Vista-related, or my driver is faulty, or the 6230 is, or is PC Suite ?
/discussions/board/post?board.id=connectivity#
Submit
THanks for your help
Hi
Did you resolve this problem as I have the same problem trying to connect using Vista via bluetooth. Prior to upgrading it all worked ok on XP.
Thanks

How to fix wifi problem and blue tooth since update with 6.1.3, how to fix wifi problem and blue tooth since update with 6.1.3

how to fix wifi problem since ios update

http://support.apple.com/kb/ts1559
After following the steps included with the link provided, if you are still unable to turn Wi-Fi on, please contact Apple for support and service options.

TS2755 I don't have an iPhone. My friend does and we have been texting for 5 months now and all of a sudden I can't revcieve her messages. I can message any other iPhone no problem and she has no problem texting other people as well. What is happening?

I don't have an iPhone. My friend does and we have been texting for 6 months and havn't had any problems. All of a sudden I cannot get her text messages. She revieces mine but i cannot recieve her's. I can also text other iPhone users with no difficulty at all.
What is happening?

I would have your friend first do a reset on her iPhone. Hold the sleep/wake and home buttons together until you see the Apple logo and then release. Also, SMS is a carrier feature and if she is having trouble, she might want to contact her carrier and have them double check her account provisioning. It might just need a reset on their end.

A665-s6094 starting from sleep problem/hibernate problem and starting form shutdown problem

hey i have a 2 day old toshiba a665-s6094 laptop and whenever i put it to sleep(as in closing the screen not from the button nor the start menu) it cant start again so i have to remove and put back the battery for it to work.
Also it on hibernate, only the display turns off and it doesnt hibernate.
and i have the same problem with shutdown, sometimes doesnt start after shutdown, and only removing the battery and putting it back in makes it start.
Any help would be appreciated.

I am 99% sure that you have the option set to require a password when waking from sleep. If that's the case, the Mac will go back to sleep after a few minutes if no password is entered on wake.
Two workarounds:
1) Turn off the password-on-wake preference, or:
2) Fast-user-switch to the login window before sleeping your Mac. When it wakes it will stay awake; and you still have the security of needing a password to get back into your user account.
Message was edited by: Király

Hello. Whenever I plug in my headphones, the music speeds up, changes, and stops by itself. And then Voice Control starts for no reason. I put back Siri to see if that was the problem and the same thing happened with Siri. How do I fix this?

When I plug in my headphones the music starts to soeed up and stop ayi g by itself. Another issue is when it does stop, Voice Control is on when I don't hold on the home button. I turned on Siri because this is what started my problem (taking off Siri) and it didn't help, instead of Voice Control, Siri started to turn on. I didn't want Siri, so I put Voice Control and disabled it. I did so, and the problem still kept on going. Any ideas on how yo fix it?

I'd guess that the problem is due to a short in your earphones. Try another set.

Problem getting DB Link to work with Warehouse Builder ...

Warehouse builder has a new Module wizard that attempts
to create a database link to a source Metadata Data Dictionary.
When I enter the DB link parameters after selecting 'New DB
Link'
I get a successful confirmation however when I try to click
on the 'Next' button on the wizard window I get 'Connection
Validation failed - the database link is incorrect'.
How is it that I success in creating a link then it fails
when I try to move to the next step in the wizard?
I tried many different ways of creating db links that I have
tested successfully but don't work within Warehouse Builder.
My environment is simple, both my Oracle 8i and Warehouse
Builder
are on the same machine and installed in the same home
directory.
Any suggestions would be appreciated.

Hi max7539! I recommend that you try setting up a new Wi-Fi connection to your phone on your camera from scratch, then see if the new app does not recognize the camera. After setting this up from scratch, does the Camera Connect app still not see the camera? If this is a time sensitive-matter, additional support options are available at Contact Us.

Weird Print problems and conversion to PDF problems...

I edited a logo in Illustrator for a hat using spot colors. 3 colors total. I saved as illustrator and then placed in InDesign for sizing. I printed it and some of the color didnt show up. So I figured it was the spot colors screwing with our printer. I printed again, but this time, in the ink manager of the print dialogue, I converted all spots to process. That substantially changed the colors in the image. I saved to PDF and then opened in Photoshop, and I get missing color plus changed color. Whats up? Looks great on screen when in Illustrator, and placed in InDesign.. but when It prints or is converted to PDF and opened in Photoshop, it goes to hell.
All Creative Suite 2 files on a Mac

Yep.. it's an overprint issue. When I open the PDF, the overprint version is all screwed up... and over print preview OFF looks fine.
Why is overprint doing anything? I dont intentionally do anything with overprint..I dont really know what overprint is, let alone want anything to do with overprint. I want whats on screen to print...
Chris

BI LSO - use of business content: problem and limitation

Hi,
we are working on BI to develop some reports from LSO data. We are using 0HR_LSO_1 and 0HR_LSO_3 for participation and resource reservation and a lot of custom datasources from infotype 1001, 1000, 1042, 5007, and so on.
We have met lot of problem in modelling a simple and flexible BI data model, because of lack of information from business content and time dependent maintenance of many information.
Just to report few of the problem we have, we notice that
1. no link between EK and D object is extracted by standard datasource, so no information is there if a D as been attemped as a single course or as a course between several from an EK object;
2. no master data is there for the 0LEARNER characteristic and no link is there with 0EMPLOYEE to better describe P object; if participant is not a P object, you don't have any information about it (!);
3.no master data is there for the 0TRAINTYPE characteristic; we needed to add lot of information to better describe the D object (!);
3. presence of 0TRAINGROUP in participation datasource may cause doubled of information (doubled count of participation) if D object is located under several L object in ovelapping time interval;
3. resource reservation datasource is not able to extract data if resource type is not defined in LSO;
4. performance is quite poor caused by lot of calculation doing by FM "read_infotype_1001" type;
5. no pre-enrolment is considered in business content;
6. no link between resource and participant is there, so you cannot provide any report of type "who partecipate to the edition with this reource type" in a simple way;
We have to develop lot of custom to handle lot of problem like those; so I would like to share experience in BI LSO data flow design and development: please let me have your observation.
thanks in advance.
L

Any experiences / contributions / documentations to share ?

Magnetic lasso problems and pixels

When using the magnetic lasso and when I create circle around figure, it goes back to lasso and does not go around whole figure for me to move. Also every time I lasso something, the little ants are around it, but I keep getting a error message that it could not complete the copy command because no pixels selected.. Need to solve the problem with lasso, then problem with the error message for no pixels selected next. Would appreciate any help you could give me. I am running PSE13 on my PC.
Trying to cut figure out of one pic and placing in another pic or background.
Would also like to know why any picture I bring out of the photo bin to work on goes immediately to the background even if I got it locked and the oirginal backgroud picture disappears.
HELP!

I have done everything you said, completed my magnetic lasso around figure, as soon as I meet and click, the lasso disappears. Yesterday when I did it and little ants moving around and let go of my mouse it changed to plain lasso inside of picture of the person but was no way to the outside and ants were still running. This morning did as you said and still problem, I tried using a brush to circle it and the ants were running just like supposed to, but when I followed your instructions edit-copy, edit-paste, I still always get the message when I click copy----Could not complete copy command because no pixels are selected every time. I have connected the loop and the little ants are still running (probably getting their little feet tired by now) and still get that error as above. Can't seem to get past that copy stage, what am I doing wrong?????
Thanks for your help in advance.
      From: hatstead <[email protected]>
To: Les Buschow <[email protected]>
Sent: Tuesday, January 20, 2015 6:24 PM
Subject: Magnetic lasso problems and pixels
Magnetic lasso problems and pixels
created by hatstead in Photoshop Elements - View the full discussion
Mr. B's pics wrote: When using the magnetic lasso and when I create circle around figure, it goes back to lasso and does not go around whole figure for me to move.
You have to navigate completely around the object that you are selecting, so that you close the loop. You can backtrack as you go along with the delete key on the keyboard, and also set additional anchor points with a left click. I find it helpful to increase the contrast, if necessary, before starting with the tool.
  .Trying to cut figure out of one pic and placing in another pic or background.
Try this
   - Open picture B, the one you wish to select something from to add to another picture.
   - Use one of the selection tools, e.g. selection brush, lasso tool, to select the object. You will see an outline ("marching ants") once the selection is complete
   - Go to Edit menu>copy to copy the selection to the clipboard
   - Open picture A, then go to Edit>paste
   - Use the move tool to position object from picture B.
   - In the layers palette you should see picture A as the background layer, and object B on a separate layer.
If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7115641#7115641 and clicking ‘Correct’ below the answer Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7115641#7115641 To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following" Start a new discussion in Photoshop Elements by email or at Adobe Community For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

MOVED: Latency problem and potentialy linked Vista problem with K9VGM-V

Similar Messages

Maybe you are looking for