MOVED: MSI P67A-GD55 (B3) uncommon / random reboots with OC Genie

This topic has been moved to Overclockers & Undervolting & Modding Corner.
https://forum-en.msi.com/index.php?topic=154614.0

Quote from: HU16E on 02-December-11, 17:09:17
If you have or can borrow a digital multimeter, please check the DRAM V. at the V-Checkpoint. It may need to be set higher. For DDR3, 1.575v's is the upper end of the 1.50v. standard. 1.65v's is considered the maximum.
I'm taking a guess that OC Genie set my DRAM V. a bit too high:
http://i.imgur.com/rpeVp.jpg
When I went to change Intel SVID to APS, I noticed that the feature was set completely to disabled. Is it safe to change to APS from Disabled?

Similar Messages

MOVED: MSI P67A GD55 not booting

This topic has been moved to Intel Core-iX boards.
https://forum-en.msi.com/index.php?topic=145238.0

Tried all ways to reset cmos, battery out and polarity swapped, jumpers to pos 2/3, cmos clear button, none of these resolved the problem so have RMA'd my board, all I can say is avoid the 1.8a (b10) bios like the plague

MOVED: msi p67a-gd55 ethernet problem

This topic has been moved to Intel Core-iX boards.
https://forum-en.msi.com/index.php?topic=147475.0

Quote from: joggesan on 10-April-11, 17:44:43
NovJoe@ it is showned as limited connectivity. It does say that there is a LAN plugged in, but with no internet connection.
There is a green light in middle, which is stable and a orange light on top which is blinking. It is the same as when it's working.
If the connection shows limited connectivity, your system is actually hotwired to the router already and the hardware are fine on your system.
What causes this to happen are 2 scenarios, one of them may need you to configure your IPv4 LAN Protocol aka I.P. address, Gateway, Subnet and DNS address in your LAN Properties. The other may be due to the Network Filtering which your router may be configured to control the access of systems accessing it, at the same time, it may also be configured to do DHCP I.P. address allocation for the pre-configured MAC addresses. In other words, you need to configure either your LAN properties in Windows or your router or both, in-order to allow your current system to be allowed to access for Internet connectivity.

MOVED: MSI P67A-GD55 B3 cannot detect Solid State Drive

This topic has been moved to Intel Core-iX boards.
https://forum-en.msi.com/index.php?topic=147894.0

Quote from: DonBoy on 19-April-11, 09:20:06
Did you try going to the bios and going to onboard chipset for sata and put in AHCI mode for sat type. This has to be done for the SSD Drive to respond. Hope this helps
Not true, a working SSD will be identified by the BIOS regardless of what mode the SATA controller is set to.

MSI P67A-GD55 Blue Screen at Shut Down or changing users

Blue Screen happens at shut down, not always, sometimes frequently but later stabilizes for a while. Computer is stable when it is working, not sudden blue screen, only happens at shutting down.
Configuration
MSI P67A-GD55 B3
INTEL Core i5 2500 3.3 Mhz
Super Talent DDR3 1333 CL9 1.5 Volt 2GB X 2 WA133UX4G9
MSI N440GT Video Card MD1GD3
2 Samsung HD103SJ 1TB Raid 1 Configuration Mode RAID
CPU Cooler Master Hyper 212 Plus
PSU Cooler Master Silent Pro M 850W
The video card was changed, before was MSI R5570 MD1G but the behavior remains the same
Could this issue be related to the problem??
http://www.samsung.com/global/business/hdd/faqView.do?b2b_bbs_msg_id=308&ref=dynamitedata.com

Quote from: NovJoe on 25-October-11, 11:09:05
I suggest that you test with one piece of RAM at a time. It may be a RAM problem.
Do post the code of the BSOD here to let us identify what the exact problem may be.
Hi, I already have two .dmp files but I don't know how to insert them in the message or open them to see the contents.
Firma con problemas:
Nombre del evento de problema:   BlueScreen
Versión del sistema operativo:   6.1.7601.2.1.0.256.48
Id. de configuración regional:   6154
Información adicional del problema:
BCCode:   1000008e
BCP1:   C0000005
BCP2:   00000000
BCP3:   AADA3AD4
BCP4:   00000000
OS Version:   6_1_7601
Service Pack:   1_0
Product:   256_1
Archivos que ayudan a describir el problema:
C:\Windows\Minidump\092811-13494-01.dmp
C:\Users\Osvaldo\AppData\Local\Temp\WER-7717650-0.sysdata.xml
Lea nuestra declaración de privacidad en línea:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0c0a
Si la declaración de privacidad en línea no está disponible, lea la declaración de privacidad sin conexión:
C:\Windows\system32\es-ES\erofflps.txt

MSI P67A-GD55 B3 cannot detect Solid State Drive

Hello Everyone!
I bought and installed a MSI P67A-GD55 B3, very happy about it, all perfect, with the exception that it cannot detect the Solid State Drive (OCZ SATA II --> Vertex 2).
The standard Hard disk (SATA II as well) works fine ...
Anyone with the same problem? Any Idea?
Thanks!

Quote from: DonBoy on 19-April-11, 09:20:06
Did you try going to the bios and going to onboard chipset for sata and put in AHCI mode for sat type. This has to be done for the SSD Drive to respond. Hope this helps
Not true, a working SSD will be identified by the BIOS regardless of what mode the SATA controller is set to.

MSI P67A-GD55 : when a new bios ?

About MSI P67A-GD55 :
When will we have a new bios with a new OROM and improved compatibility with other DDR3 and SSD.
I have issues (BSODs) with 2 kinds of SSD : OCZ Vertex 3 and CRUCIAL M4.

What is your current UEFI/BIOS Version?
What memory modules are you using?
Latest UEFI/BIOS Release can be found here:
--> https://forum-en.msi.com/index.php?topic=144655.msg1131342#msg1131342
It already includes a new Option ROM Version.

MSI P67A-GD55 (B3), i7-2600k, supports Corsair Vengeance 2x4GB?

Hello there!
Anyone knows if i can use the Corsair Vengeance 2x4GB (CMZ8GX3M2A1600C9) with MSI P67A-GD55 (B3)?
I searched on the official site and they are not verified. Can Someone help?

TS3274 My iPad mini retina is still having random reboots with blue screen after updating to iOS 8.0.2.i also did reset my iPad.But the problem still persis

My iPad mini retina is still having random reboots with blue screen after updating to iOS 8.0.2.i also did reset my iPad.But the problem still persists

Could you add your problem here: https://discussions.apple.com/thread/6569052? This makes sure the discussion and in one place and we can attract more attention from Apple.

MSI P67A-GD55 stock VCIO overvolted !

Hi everyone !
I'm coming here for a little help .
When I let the voltage on "AUTO" in the bios , it set the VCIO voltage to 1.25v which is a little to high
I manually set it to 1.05v like it should be , but I'm afraid of bios error like that O_o
It does this since i updated the bios to the last one (1.J)
I'm using a P67A-GD55 (B3) bought 1 week ago with a nice and shiny core i7 2600k on it ^^
So , should I right an email to MSI support to inform them of the bug or maybe it's a well-known bug and they are working on it (last bios is a bit old ...)
Thanks

Flash back to the previous BIOS version and report your finding to technical. >>How to contact MSI.<<
Please use the forum flasher to flash back. >>Use the MSI HQ Forum USB flasher<<

Did I just brick my board? MSI P67A-GD55

So I decided to flash my BIOS to the newest version. I downloaded the newest BIOS and proceeded to flash the BIOS with the MSI utility. After the computer restarted it beeped a couple of times like usual, but it did not continue to windows after that and the screen went black. I saw that the USB stick was being used(light on the USB stick was flashing) so I didn't do anything.
But even after about 45 minutes nothing at happened, the screen was still black. I was reading around online and some people said to clear the CMOS if this happens. After I cleared CMOS and restarted the computer, I got no beeps and no video signal at all. And now nothing happens at all. It does not even beep like usual.
I removed all the ram and restarted the computer and that time I got 3 long beeps. When I put them back in nothing happened like before. So did I brick my board? Is there any way to bring this board back to life? This board was advertised as having a Bios recovery feature(M flash) anyone know how I can use that?
Thanks for your help.
BTW, I am already going to get a new board, but I won't have it until at least the end of this month. Anyone know how long MSI RMAs take? Will they even RMA the board?
Not related, but I was also having a problem with fan control on this motherboard. No matter what the CPU fan would run at max speed.
Specs of my build:
i7 2700K
MSI P67A GD 55 Rev B
16GB Team 1600Mhz RAM
MSI 660Ti PE OC
520W Antec Neo Eco PSU
1 TB Seagate Barracuda

Quote from: xmad on 10-March-13, 10:25:51
If you sent it to MSI in the USA, that is odd as they usually turn things around in 7 working days. If it is a re-seller or outside of the USA it is hard to say how long it will take.
In the usa to check for status, email [email protected] Place the RMA# in your subject and ask for an update.
Yeah this is in the US, the place I sent the motherboard to is only like 3 hours from my house actually.
I'll send them a email. Their online tracker doesn't seem to be updated that often and I can't even go to the tracking page right now for some reason.

Random reboots with 975x Platinum v2.1?

As the title says, I have the MSI 975x Platinum v2.1. The system randomly reboots fairly, often, and I'm not sure what could be causing it.
I had this setup for a few weeks, before it locked up overnight and destroyed my memory. Board would halt on the memory initialization during POST, so I sent it back for RMA and now have the replacement. While waiting for the RMA, I bought some memory from a local retailer so I would have something to use. The system would randomly reboot, sometimes in Windows, sometimes while browsing the BIOS menus. I figured the motherboard was damaged too and I sent it back to the retailer for a RMA replacement. I now have the LE version of the board. I also bought a new power supply because I now thought it fried my stuff. Everything put back together, I'm still having random reboots. Here's the system specs:
# Intel Core 2 EE x6800
# MSI 975x Platinum v2.1 LE (BIOS 7.4 official)
# mushkin REDLINE 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 1000
# BFG Tech BFGR79256GTOCE GeForce 7900GT 256MB GDDR3
# 1x NEC IDE DVDR, 1x Seagate 200GiB IDE, 1x Seagate 80GiB SATA2, 1x Seagate 400GiB SATA1, 1x Seagate 500GiB SATA2
# Windows XP Pro SP2
# Tagan TG-480-U22 ATX 480W, then mushkin HP-580AP ATX12V / EPS12V 580W
Currently, the system can play games for a couple hours with dnetc running in the background. Yet when I leave it running a torrent (or whatever) overnight, I'll wake up and find it rebooted (after like 6 hours of uptime). I've also gotten it to reboot while just browsing web pages for a few minutes. The northbridge heatsink/heatpipe does get pretty hot, and my room does get warm, so I'll try adding a spare fan tonight. Though, I find this unlikely as the system should be working fine at stock speeds/voltages. Other than that, anyone have any suggestions?

I was actually using the Tagan in combined mode until I started having problems (ie, when the RAM died). By then, neither combined nor split appeared to have any helpful effect. I do not know if the Tagan was the cause of my problems, or if this is all something (???) else. I suppose I could try it again, but I'd rather not break my newly RMA'ed stuff. The mushkin power supply has 4x 20a 12v rails, but it appears to automatically determine whether they should be combined or split.
Speaking of the 12v rails. I noticed that the BIOS reports varying values for the 12v. I've seen it at 12.3v, 13.0v, 13.7v, and 14.0v. However, the dualcorecenter software in Windows always reports 12.2v - 12.3v. I have no idea which is accurate.

Random Reboots with dual channel

Hi,
I just bought yesterday the following system.
Intel P4 2.8 Northwood HP enabled
MSI 865PE/Neo 2 Platinum Edition
Maxtor Diamond Star 9 200 GB 8MB Cache 7200rpm
Elixir 2x512MB DDR 400 CL3
Toshiba DVD 16x
Creative Geforce 4 Ti 4400 128MB
Logitech Cordless Keyboard connected and a logitech cordless optical mouse
19 inch belinea monitor.
The power supply is a no name product LPK2-30 with the following specs.
420W
3.3V 28A
+5V 36A
-5V 0.5A
+12V 17A
-12V -0.8A
It says that is P4 ready, i know which does mean nothing
Operating System:
Windows XP Professional SP1
All Hotfixes and Updates applied
Newest drivers for all the system parts
The errors during the windows crashes are irq not less or equal or page fault, which looks for me pretty much like a problem with the memory.
Ok what i tried so far.
Single channel with 512MB works fine.
Single channel with 1GB works fine except one strange thing restarting the machine and it got stuck during the bios loading worked fine after i pressed reset.
Dual channel 1/3 1 GB get random reboots.
Dual channel 2/4 1 GB even worse but i think at this point my newly installed died.
I tried to set memory voltage from 2.65 up to 2.8 but did not change the behaviour.
memtest with one modules in slot 1 no errors
memtest with dual channel 1/3 1 gb no errors running 30 minutes
i will try now a memtest with the second single module in memslot 3.
No MAT or dot ram settings are 3,3,3.
I am bit running out of ideasö
before i forget i updated the bios from 3.3 to 3.5 but did not change the problems.
Maybe you guys have some ideas what else can i try.
thx a lot in advance. i hope i provided all informations which are necessary.
greetings faxe

Hi,
i tried a few more things which make confident that i have the problem narrowed down to the memory.
i tried to install windows again with only using the third memory slot single channel and it worked fine.
now i tried to go down with the memory speed to ddr333 and using dual channel and so far that seems to work too.
so i think i will go for other memory.
if you think i am wrong please correct me
greetings markus

Mysterious random reboot with iPod Touch 3G running 3.1 firmware

Hi everybody,
I ordered an iPod Touch which arrived last week, thinking that it would be the third best thing ever happened to my life (besides my girlfriend and my mac book pro). However it has been a big disappointment for me since the first day I used it.
I have been using the iPod for about a week now, and it randomly crashes and automatically reboots 5 or 6 times a day. I tried restoring it several times but to no avail. I also closely followed this post about random crashes with iPhone running 3.1 firmware (http://discussions.apple.com/thread.jspa?threadID=2152619&start=0&tstart=0).
At first I thought this annoying bug is common for both iPhone and iPod touch user running 3.1. But it's weird that no other user using iPod touch is complaining about the problem. So I'm thinking this might be a hardware problem.
If you guys have any possible solution, or if you are using iPod Touch and have the same problem, please reply. I want to make sure before contacting Apple and exchange for a new one. By the way, it's totally unacceptable that:
1. Apple didn't announce the problem and apologize to the users who are suffering and literally losing money everyday due to this bug
2. Apple blocked the online support feature, I'm gonna have to arrange an appointment with them via phone, but the nearest apple support center is 2 hours away by car.
Thanks for reading and I hope there's a way to address this problem soon.
Message was edited by: Gary Cao

apparently... no.. it still occurs in the 3.1.2
i believe it has something to do with memory and the touch scroll. graphic? defect on the touch tech in the 3g? or am i just unlucky to pick that one?
... im gonna exchange or probably get my 280 bucks back from costco.
y the memory and touch scroll? memory failure most of the time result in sudden reboot to computer. (IPOD TOUCH AND IPHONES R MINI MINI COMP SO JUST GET U IF U WANT TO ARGUE ABOUT THIS) Touch screen really just... start the reboot... on my home page. scrolling back and forth and suddenly... scratchy statically-like screen and fades in dark and then silver apple pops up. same result on scrolling on youtube, safari, and other apps that requires u to scroll. ... im just hoping that i get the ipod touch 3g again and obtain a totally not defective one

Iphone6 ,ios 8.2,8.3 randomly reboot with blue screen

i have an 64G iphone 6 with ios8.3 .my problem is blue screen!I had it before this update too but now is intorable! sometime my wifi drop and it randomly reboot And sometimes it shows blue screen and randomly reboot ;i think it is beacuse a software bug.
It happen 4 or 5 times a day! I think im not alone ,also my friend have this problem on iPad Air2.

Exactly the same issue with iphone 5s 64G. It started with iOS 8.2 and then 8.3.

MOVED: MSI P67A-GD55 (B3) uncommon / random reboots with OC Genie

Similar Messages

Maybe you are looking for