MOVED: New H97 Gaming 3 will not POST with i5 4690 - Need an old CPU to reflash BIOS?

This topic has been moved to GAMING Motherboards.
https://forum-en.msi.com/index.php?topic=253392.0

Quote from: nealshireman7 on 21-February-15, 22:34:27
I believe I an old version of the BIOS that is incompatible with the i5 4690 but I need the CPU to work to update the BIOS..
Beliefs and computers are two opposite things.
http://www.msi.com/support/mb/H97-GAMING-3.html#support-cpu
Did you put it all in the case or is it still on the bench?

Similar Messages

New H97 Gaming 3 will not POST with i5 4690 - Need an old CPU to reflash BIOS?

I just finished assembling my new computer with an i5 4690, H97 Gaming 3, 8GB Kingston DDR3 RAM, 600W PSU. I ordered everything from Amazon a week ago.
When I turn it on, it does not POST or beep, it just power cycles every few seconds. I don't know what BIOS version it has because nothing shows on the screen. I believe I an old version of the BIOS that is incompatible with the i5 4690 but I need the CPU to work to update the BIOS..
I'm not sure I am reading the compatibility list correctly. Are CPUs listed as "7918v10.zip" working on stock BIOS?
msi.com/support/mb/H97-GAMING-3.html#support-cpu
I will install an old CPU, reflash BIOS with current version, and replace the CPU with my i5 4690.
I read on Tom's Hardware that the Pentium G3258 is compatible with stock BIOS. Is this true?

Quote from: nealshireman7 on 21-February-15, 22:34:27
I believe I an old version of the BIOS that is incompatible with the i5 4690 but I need the CPU to work to update the BIOS..
Beliefs and computers are two opposite things.
http://www.msi.com/support/mb/H97-GAMING-3.html#support-cpu
Did you put it all in the case or is it still on the bench?

I have a new computer now with windows 8. Old one was windows 7. The itunes library contains all I expect on new computer. Ipod will not sync with content. It says it is syncing but only picks up 1 tune. Solution please. I am on itunes 64 but it makes no

I have a new computer now with windows 8. Old one was windows 7. The itunes library contains all I expect on new computer. Ipod will not sync with content. It says it is syncing but only picks up 1 tune. Solution please. I am on itunes 64 but it makes no difference from 32 bit.

See this older post from another forum member Zevoneer covering the different methods and software available to assist you with the task of copying content from your iPod back to your PC and into iTunes.
https://discussions.apple.com/thread/2452022?start=0&tstart=0
B-rock

I have Adobe Elements10. The RAW images from my new Canon G16 camera will not open. Do I need an upgrade?

I have Adobe Elements10. The RAW images from my new Canon G16 camera will not open. Do I need an upgrade?

carolweiler wrote:
I have Adobe Elements10. The RAW images from my new Canon G16 camera will not open. Do I need an upgrade?
See:
Camera Raw plug-in | Supported cameras
You need the 8.2 version of the ACR module, and PS10 is too old to be updated.
So, you can choose between 3 solutions:
- update PSE to PSE12
- use the Canon software to convert the raw files to the tiff format which PSE10 can handle
- download and install the free Adobe DNGconverter which is able to convert a whole folder of CR2 raw files to the Adobe DNG raw format which PSE10 can handle.
The last two solutions are free.

My computer died rather rapidly so i had no chance to do a backup or anything. now i want to put itunes on my new computer but it will not sync with my ipod. i got my purchased music but not the playlists and it does not sync when i plug it in.

my computer hard drive died rather suddenly so i had no chance to do a back up or any thing. i put itunes on my new computer and got my purchased music but my ipod will not sync and i cannot get my playlists onto the computer. is there any way to get my playlists on my new computer and also get my ipod to sync. it is a waste of time to purchase new music and i do not want to purchase a new ipod since i have so much memory left on this one.

Thank you all for your replies. Here is what i ended up doing. I cannot afford any 3rd party software so i went to itunes and manually entered all my playlists. As I had indicated my purchased music was on my new computer just not the playlists and I could not sync my ipod. After I rebuilt all my playlists I tried to restore my ipod to factory defaults/new. All of the steps called for in apple support and elsewhere were not available to me. I connected my ipod, went to my computer, right clicked my ipod, and formatted. That wiped my ipod so when I connected to itunes it then gave me a restore option. I did the restore and all is good in the empire again. I can now buy new music and sync my ipod so I am a happy camper.
Thanks to all.

Iphone 3g will not see my new apple id so will not sync with cloud

I changed my apple id because i no longer had access to the old email address - what a mess! I finally got the ipad to recognize the new id but the iphone automatically sees the old id and will not "take" the new one. I went to the apple store and signed out of the old id and and into the new but it still sees the old id whenever I try to back up to the cloud
Please help me I am losing my mind.

Disregard - someone much smarter than I showed me to delete the account and then replace it wiht the new one. Thanks to him I'm all set

New Blackberry 3g 9330 Will Not Snyc with MS Outlook Calendar

Just moved from the BB Curve 8330 to the 3g 9330. I went through the sync set up in the BB Desktop software. However, after several syncs, not all calendar entries copied from the BB 9330 to Outlook 2003. I have Windows XP. I double checked the settings, but don't know where to turn. I use this for business, so any help will be appreciated.
Solved!
Go to Solution.

I would try the solution in scenario 2. That should get all your calendar events into your default calendar so you can sync everything to Outlook.
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

P43 Neo3-F will not post with Vertex SSD attached

Without my OCZ Vertex SSD attached, my rev. 1.1 P43 Neo3-F with bios v2.4 acts like a normal mainboard. As soon as attach my Vertex SSD, it freezes during POST. If I bring up the boot menu during POST and pick the SSD, I get a blinking cursor and no post. I tried several of the regular SATA (non-Jmicron) ports but the same result.
Do I have to change the SATA mode on the SATA ports for an SSD to work? I think I remember seeing that your port should be set to IDE mode for this SSD in the OCZ forums. Can someone tell me where in the bios I could find this option? I'm having a lot of trouble finding stuff in this bios.
If that is not the case... there is one newer bios I could flash too. I read the directions and it says don't flash from floppy - which I've already done. Do I really have to go throught that RAMDRIVE stuff it discusses or is flashing from floppy okay as long as the floppy is "good". I know of the USB stick method but won't be using that.
But I have trouble believing that a P43 mainboard would be incompatible with an SSD. What's odd is that I didn't have this problem until I installed WinXP on the SSD. I could see that interfering with booting but why would that interfere with POSTing?

I flashed the bios to the very latest for the 1.1 version... the 2.5 bios but no help. I now have WinXP installed and it loads but the BIOS chokes on the SSD and there is a 25 second wait followed by about 10 second black screen and then the desktop just magically appears - no XP progress bar ever seen. Whenever the SSD is attached to the board, it lets out a strange chirp sound after the good post beep.
I tried installing XP on the SSD on my DFI Blood Iron and it works perfectly. I tried changing every related bios option on the MSI board I could find but nothing helps.
Anybody here running a Vertex on this board?

New Epson WF 7620 will not print with Macbook Air, receive "Print File Was Not Accepted" message.

Hello! To anyone who tries to help me, thank you in advance!
I brought home a new Epson WF 7620 yesterday and did all the necessary stuff, installing it with my Macbook Air (Mac OS X ; 10.7.4.). I installed the software from the site, added the printer to my printer list, enabled "print sharing" and connected it to my wifi network. I am trying to use it wirelessly.
I tried to print a test page of a regular PNG image, but I am receiving the "Print File Was Not Accepted" message in my printer queue. I have changed the file type a couple times to JPG and PDF but more of the same. I have also reset the printer, and have repaired the disk permissions in the Disk Utility to try and get it to work.
None of this seems to be working, suggestions very appreciated!
Thanks
MP

Try Linc's suggestion first. That should cure your issue. If not, here's something else to consider:
PrinterMaccer wrote:
I installed the software from the site ...
Apple keeps a set of current software for Epson printers. You should start by going to System Preferences > Printers & Scanners and delete the printer from the list (using the "-" key). Then download Apple's software version from here:
Epson Printer Drivers v2.18 for OS X
Finally, set up the printer as shown here:
OS X: Connecting a Wi-Fi printer to your Wi-Fi network

I have a new ipod, but it will not sync with my playlists?

I have changed my Ipod nan for a classic but it cannot access my playlists?

Thank you all for your replies. Here is what i ended up doing. I cannot afford any 3rd party software so i went to itunes and manually entered all my playlists. As I had indicated my purchased music was on my new computer just not the playlists and I could not sync my ipod. After I rebuilt all my playlists I tried to restore my ipod to factory defaults/new. All of the steps called for in apple support and elsewhere were not available to me. I connected my ipod, went to my computer, right clicked my ipod, and formatted. That wiped my ipod so when I connected to itunes it then gave me a restore option. I did the restore and all is good in the empire again. I can now buy new music and sync my ipod so I am a happy camper.
Thanks to all.

My new 5th generation ipod will not sinc with my itunes account

i can not sinc my ipod touch to my itunes account it doent even read that it is a device

Here:
iOS: Device not recognized in iTunes for Windows
or
iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
You need iTunes version 10.7 or later on the computer.

Mac Pro will not boot with Snow Leopard - need help!

I have had a lot of issues with Snow Leopard since I upgraded from 10.5.8. Most of my problems started after installing Office 2007. I finally wiped the hard drive and reinstalled everything. No problems until last week. Start up was taking longer and had to reboot a couple of times because of grey screen. So I would just put computer to sleep. Yesterday the computer was frozen on screen saver with scrambled rows of pixels on screen two and the main monitor had a frozen image.
I initially pulled all peripherals out and pulled the power plug for 5 minutes. I have left the peripherals out and pulled the second monitor as well. I tried pulling the power plug during a few more starts but nothing gets me to a complete start up screen.
I have tried resetting PRAM and VRAM and tried a safe boot. I tried booting from Snow Leopard and my Leopard disk stayed on either a blue or gray screen with spinning beach ball (on gray screen).
Put original install disk in and booted from using D to check the hardware. Good news is that the hardware test was OK. I did the extended test.
All different kind of start up problems.
- Some start with start up sound goes to Apple logo to blue screen to grey screen with beachball
- Some start ups with no initial sound then Apple logo to blue screen to grey screen with no cursor or beachball
- Some start ups with no sound to gray screen to blue screen to grey screen.
I have no problem wiping the HD1 again but I can't even get the OS disk to be recognized with holding the C key during start up. This last time it went to a blue screen (holding the C key) and a cursor.
I don't know what else to do - Please help!!!

There are lists (MacIntouch and MacFixit) of hardware / software support issues with 10.6. Accelerateyourmac is another place to watch.
There were some really long threads back in Sept about printer driver support.
The 7300 firmware was more about Windows support; those cards are failing and dropping like flies (how DO they know 3 yrs has expired anyway?) and they don't support SL features like OpenCL etc so I'd invest in ATI 4870, best graphic card and works in all models Mac Pro.
Lots and lots of bootable clones for backup. Never need to wipe and install again.

MS-6580 (845PE Max VER 2.0) not POSTING with 2GB of DRAM -- POST with only 1GB

Ok I am currently fixing a client's PC, he wanted a RAM upgrade from 1GB to 2GB. I purchased a Komputerbay 2GB (2 X 1GB) DDR DIMM (184 PIN) 333Mhz DDR333 PC2700 kit, it was the cheapest I could find. The problem is, the system will not POST with the two 2GB modules installed, only with 1GB on either DIMM slot. I've tested them both RAM modules, and they work. Before, the PC had 2x 512MB DRAM installed, and it was working, so I don't think there is anything wrong with the DIMM slots.
When I start the system, I get two paused beeps, and some weird noise, not sure what is.
I've read the motherboard manual, and it says the maximum support is 2GB DDR 333mhz.
Any help would be appreciated, thanks!
PC Specs:
[ALL SETTINGS ARE STOCK -- NOT OVERCLOCKED]
CPU: Intel Pentium 4
MOTHERBOARD: MS-6580 (845PE Max) ver.2
PSU: Q-Max 350W ATX
GPU: nVidia e-Geforce2 NV11-A1 MX400 64MB

Quote from: Mike on 22-October-11, 03:36:53
Does it post with only one 2GB dimm installed?
I don't believe the board/chipset will support 4GB(2x2GB).
http://eu.msi.com/product/mb/845PE-Max2.html#/?div=Detail
I don't know where you're getting 4GB, I never said anything about 4GB - I must have made a type but what I mean was: The motherboard wouldn't post with two 1GB modules (2GB) as specified to be the maximum according to the manual. It would only post with 1GB(1x1GB or 2x512MB) or 1.5GB(1x1GB + 1x512MB) of RAM.
No worries, the problem is resolved now.

I have moved from the UK to New Zealand and Itunes will not accept my new Zealand bank details, as a result nothing will work on my phone and I cant access emails!

I have moved from the UK to New Zealand and Itunes will not accept my new Zealand bank details, I am trying to change my details on the Iphone 4s

Do you have a new Apple ID to use in NZ? If not open iTunes Store. Log out of your old Apple ID, then try to login. Select Create Apple ID from the dialog that appears. Make a new Apple ID for NZ with a NZ email address. Once that is approved and verified, log into the iTunes Store with the new Apple ID. This should fix all other issues.
Change iTunes Store Country on an iDevice
1. Tap Settings;
2. Tap iTunes & App Stores;
3. Tap View Apple ID;
4. Enter your user name and password;
5. Tap Country/Region;
6. Tap Change Country/Region;
7. Select the region where you will be located;
8. Tap Done.
Also, see How to Change Your iTunes Store Account Location | eHow.com.

K8T Master2-Far Will not POST unless CMOS is freshly cleared!

Hey all, thanks for helping out.
I came back to my computer one day to find it in a coma. The system was on, but the screen was getting no signal and would not come on by moving the mouse/keyboard like usual. I thought that maybe it had turned off the monitor for power save and then frooze some how. After restarting the computer I found that it was still doing the same thing. I shut down the system and unpluged. After waiting about 5 min i plugged back in and flipped the switch on the powersupply. This started the computer right up (even though i had not pushed th power button) and left it in the same condition as before. It simply would not post. After closer inspection I found that it was not posting because it wasn't getting far enough in the process before it was being restarted. I checked the restart button and even went as far as removing it from the motherboard. This did not help. I knew it was restarting because i could see it checking the optical drives then waiting for about 4 seconds, then a weird noise from the speakers (like a soft cruching so to speak) would happen, then it would do this all over again, non stop. That noise was familliar though, it was the normal noise that I hear when I push the restart button (I'm guessing a release of electricity etc..) so I knew what was going on.
After switching the memory out and in all orders, I stripped the system down to the bare min. This however did not change anything. I put the system back together and flashed the cmos. This made the system restart once, then "BEEP" it posted. It said CMOS Checksome Error - Defaults Loaded. I first pushed DEL to get into the bios. I changed everything back to how its suppost to be (time, apature, etc...) then saved and exited. This made the system go back into its restarting state. I then flashed the cmos again and pushed F1 to continue. The system booted up just fine. In safemode of course. Then i restarted. It then went back into its restarting state. I flashed the bios again. And after pushing F1 to continue selected it to go into windows normally. Everytime it does this it gets different results. One time it got past the windows xp loading screen and sat at the black screen before you get your curser and welcome screen (sigh... restart... flash..). It also once got in just fine, and after about 5 min got a blue screen about "bad pool caller". It most the time however gets a random blue screen right after you see the welcome screen. These blue screens consist of "bad pool caller", "IRQ Equal or Lesser Value", or No notes, just generic blue screen.
If i change anything in my bios it will not post. If i dont flash the cmos, it will not post. If i dont change anything in bios and continue, then restart, it will not post. The only way for it to post and for me to see anything on the screen is to flash the cmos. I thought it might be the power supply, but the only extra i have does not have the extra plug to power the 2nd cpu. After thinking about it though. I dont know if it could be a power supply issue, if it was then would it even load up into safe mode? Or why would it not load up into safe mode again after restarting. I have tried an extra stick of memory that i know works in a separate computer, but nothing changed. I have tried a different videocard... nothing changed. I have removed everthing accept the basics (motherboard, cpu's,videocard,memory,psu) and nothing changed.
I have worked on this for about 1 week now and can not figure it out. I have my useless MCSE/CSE/A+ certifications (I say useless because I dont have a job that uses them) but this one is beyond me. If anyone could help I would appreciate it.
Thanks,
Brandon
P.S. I dont know if this is related, but I did have to change from useing the DVI connection to RGB plug to even see anything once I heard it post. I was useing DVI before, and once i figured out that it would post after flashing cmos, I had to change to RGB to get any visual. The DVI will not work now at all. I have even tried changing cords. The DVI wont work in safemode either. Thanks

I reckon these mobos have a fault that really needs to be sorted. You say that your PC was working fine using PC 3200 memory with 240's. I have a similliar problem, I am using 246's with Kingston' PC3200 KVR333X72RC25/512D 2.5 ECC REG. The PC worked fine for about two weeks and then one day went on a blink, every time I power it up all I get is beeps. I was forced to order new BIOS, which didn't work everything else has been tested and works fine.
So I ordered micron memory 2X512 PC 2100 266 ECC REG which I was told by the supplier that it was compartible, that didn't work either. I then went on to check the battery, to my surprise the battery was low so I thought I had nailed it, went out bought a new battery but the problem still exits. I must say though after installing the micron memory it did boot up but when I went into BIOS to change settings to boot fro CDROM the damn thing would not restart I had to switch it off using the power button to restart it and when it restarted all i got was beeps. After that to get it to bootup I have to reset CMOS using the jumper and when it boots up it gives a checksum error message. I have a choice of two at this stage
(1) To Press F1
(2) To Press delete o go into BIOS setup
The F1 option takes me as far as the windows log on screen and that's it cuts off as if it is gonna boot itself backup but just hangs there.
The Delete option takes into BIOS which when exited the PC does nothing until powered down and powered up again, from here I have to reset CMOS to get it to bootup.
I have been told that the kingston memory is not compatible but my question is how did it work the first two weeks?
Good ol' Bas have helped out on this one quite often but here I am three months on still in a struggle. I thought of RMAing the board but it would cost me about 160 pounds and with that kind of money I could pick up another boad from kompllete.com and remain with some change for a couple of buds.
"To bass You said in the last post that the poblem could be the power supply changed it but that has not solved my problem"

MOVED: New H97 Gaming 3 will not POST with i5 4690 - Need an old CPU to reflash BIOS?

Similar Messages

Maybe you are looking for