MOVED: OS doesn't boot if IOAPIC is enabled in BIOS on 760GM-E51
This topic has been moved to Linux/Unix.
https://forum-en.msi.com/index.php?topic=145547.0
I would like some more info on your system to help you. What is the exact model of your power supply? What is the maximum output rating, in amps, on the +12V output? This is very important. It sounds like you might be on the edge and under certain circumstances, it isn't enough to get everything started correctly. It sounds like you are getting intermittent memory errors and that can be caused by a weak power supply. Also, are you OC'ing? If so, what settings are using, I am interested mostly in your HTT speed and the vo,tages you are running the RAM and CPU at.
Also, I noticed that you have corsair RAM. Corsair RAM has 100% satisfaction guarantee on their RAM. As long as you haven't physically altered the PCB, they will replace or refund your money. You should have no problem getting either a replacement or your money back.
good luck!!
RB
Similar Messages
-
Refind-efi 0.8.1-1 doesn't boot with custom refind.conf
Recently upgraded to refind-efi 0.8.1-1 and manually ran refind-install.
I usually have the option ¨default_selection "bzImage,vmlinuz"¨ enabled in refind.conf but after some trial and error I found refind wont load the default boot entry with this enabled any more.
I moved
/boot/refind_linux.conf
and
/boot/efi/EFI/refind/refind.conf
and performed a ¨clean¨ refind-install.
If I select the default boot entry, with ¨default_selection "bzImage,vmlinuz"¨ enabled, refind shows the normal boot screen with standard options, but doesn't load the kernel. If I press F2 and select the boot with minimal options (in this case the same as standard options) the kernel boots instantly as expected.
If I use the standard refind.conf-file w/o ¨default_selection "bzImage,vmlinuz"¨ the default boot-entry with standard options works fine.
Anybody able to reproduce?\hbar wrote:Strange... A rEFInd bug perhaps?
I suspect so, but would like to see it reproduced before I file a bug towards rEFInd.
\hbar wrote:When you select the arch entry, is the line that specifies the kernel and its version the same whether the default_selection is set or not?
Yep, the commandline options "ro root=UUID=836e34d6-bc33-4044-a337-372a3d240f49 quiet" plus initrd are the same in the "Booting OS"-screen, whether I select the default "Logo"-entry, or specify which options to boot with via F2.
\hbar wrote:What if you set 'default_selection arch'?
Don't think that's supported, and it doesn't work .
I've also tried "bzImage", "vmlinuz", and "vmlinuz-linux" seperately with the same result.
Should I file a bug now or wait until somebody experiences the same problem? -
Adding 512mb ram doesn't boot up my MSI-6585!
My mobo is Max 648, MSI-6585 and I have Kingston KVR333X64C25/512 ram. I had installed it in first slot, moving 256mb PC2700 to other slot.
It will not boot up, and there were diagnosis leds light up telling me it's a fault memory or not installed properly so I took it back to shop and exchanged for another one.
And had a go with it, iy's the same as before.
I have been downloading test report and it states that this ram will work!
Is there anything I am missing? ?(
Installing ram should be straightforward??Actually, 256mb pc2700 ram comes with motherboard works fine.
But my pc doesn't boot up with 512mb ram installed, even on its own (does boot up but produces some errors in windows XP)
However, I have checked everything and there's one thing i'm unsure about, I noticed that Hyper Threading is enabled on bios even though my intel CPU doesn't have HT. I have disabled it but i haven't test 512mb ram yet (with HT disabled) as i need to know what is causing this ram problem. Could enabling HT causes problem with rams or nothing at all?
I was contacted by Kingston support and they asked me if i have updated bios in my mobo and i checked, it's AMI 3.31a which is the latest at the moment as i have only received mobo a week ago.
But I have found other 648 Max mobo, MSI 6585 Mobo (without HT) it has bios version 1.5 as the latest.
My mobo manual logo say 648 Max (but didn't say HT)...could be mixed up?? ?(
But I assumed mine is 648 Max HT because my bios screen showed its AMI v3.31a which is like that since I receive this mobo.
Also could bios settings effect rams installed? -
Thinkpad T440p BIOS Update Bootable CD doesn't boot
Hi,
I want to update my laptop (Thinkpad T440p 20AW)bios to the latest version 2.24 released 04 Jun 2014, but I can't! As always I burn the iso file on a cd and try to boot with cd but after the first THINKPAD screen it doesn't go to the bios update screen and it returns to THINKPAD screen. I tried to install updates through an usb stick but the same. I mean moving(installing) the iso image on a usb and trying to boot with usb to update the bios but it doesn't work too. Here with F12 at boot time I choose the usb to boot but it doesn't boot and it returns to choose device list.
Any advice?!If the OS on your laptop is Windows 8 the most chance the cause is "Secure Boot" settings. It prevents the boot from external device by default.
Read the User Guide for your laptop, there are BIOS Setup menu settings descriptions.
x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
Do it well, worse becomes itself
Русскоязычное Сообщество English Community Deutsche Community Comunidad en Español -
K9N Platinum - Doesn't boot with PWR2 connected
Hi,
I've just built a new PC with a K9N Platinum Motherboard (7250 Ver 1.0)
I immediately discovered a problem:
-If I connect to the power supply the PWR2 Molex (the additional power connector on the motherboard, to provide additional power to the video card) the system doesn't boot. Computer's LEDs get on for half a second, then it shuts down.
-If I deconnect the PWR2 connector, computer boots fine.
Bios already flashed to 1.51... no results.
It sounds weird to me. I have an Enermax Noisetaker II 485W PSU, the CPU is an Athlon X2 65W...
Have I got a damaged mainboard?
Thanks for supportQuote from: WillyTP on 15-February-07, 05:36:01
Just tried... nothing. Lights and fans turns on for half a second, then everything dies.
I tried to remove video card too, nothing changes :(
sound like somethink is shorted. try take board of case and retry. it maybe dumb question, but are you connect 4pin cable in a right direction?(i know its can be plugged in one way only, but if you use little more force can be done...) -
My mac is slow, crashes if iPhoto is opened, doesn't boot sometimes
Hello.
In the last time, my MacBook Pro is very slow and crashes sometimes if I open iPhoto or some other programs.
Sometimes, there comes a black display with some thin white lines and then I have to restart the computer.
Also, sometimes the mac doesn't boot right (you see only a grey display after the apple symbole).
I already repaired the system with Disk Utility and erased it to install a backup of my system.
Thank you for your help!
Best regards....
Here is the EtreCheck result:
EtreCheck version: 1.9.15 (52)
Report generated 27. September 2014 17:42:12 MESZ
Hardware Information: ?
MacBook Pro (15-inch, Late 2011) (Verified)
MacBook Pro - model: MacBookPro8,2
1 2.4 GHz Intel Core i7 CPU: 4 cores
4 GB RAM
Video Information: ?
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1680 x 1050
AMD Radeon HD 6770M - VRAM: 1024 MB
System Software: ?
OS X 10.9.5 (13F34) - Uptime: 0 days 0:5:31
Disk Information: ?
APPLE SSD TS128C disk0 : (121,33 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted>: 209,7 MB
Macintosh HD (disk0s2) / [Startup]: 120,47 GB (14,71 GB free) (Low!)
Recovery HD (disk0s3) <not mounted>: 650 MB
MATSHITADVD-R UJ-8A8
USB Information: ?
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ?
Apple Inc. thunderbolt_bus
Gatekeeper: ?
Mac App Store and identified developers
Kernel Extensions: ?
[not loaded] com.NovatelWireless.driver.NovatelWirelessUSBCDCECMControl (3.0.15) Support
[not loaded] com.NovatelWireless.driver.NovatelWirelessUSBCDCECMData (3.0.15) Support
[not loaded] com.ZTE.driver.ZTEUSBCDCACMData (1.3.8) Support
[not loaded] com.ZTE.driver.ZTEUSBMassStorageFilter (1.3.8) Support
[not loaded] com.novatelwireless.driver.3G (3.0.15) Support
[not loaded] com.novatelwireless.driver.3GData (3.0.15) Support
[not loaded] com.novatelwireless.driver.DisableAutoInstall (3.0.15) Support
[not loaded] com.novatelwireless.driver.NWVBE (3.0.15) Support
[not loaded] com.novatelwireless.kext.wwan (3.0.15) Support
[not loaded] com.option.driver.OptionHS (3.31.0) Support
[not loaded] com.option.driver.OptionMSD (1.22.0) Support
[not loaded] com.sierrawireless.driver.SierraDIPSupport (1.0.0) Support
[not loaded] com.sierrawireless.driver.SierraDevSupport (1.0.7) Support
[not loaded] com.sierrawireless.driver.SierraFSRSupport (3.0.0) Support
[not loaded] com.sierrawireless.driver.SierraHSRSupport (3.0.0) Support
[not loaded] com.sierrawireless.driver.SierraIPDirect (1.1.3) Support
Startup Items: ?
ChmodBPF: Path: /Library/StartupItems/ChmodBPF
HP IO: Path: /Library/StartupItems/HP IO
Launch Daemons: ?
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.sierrawireless.SWoCTool.plist Support
User Launch Agents: ?
[failed] com.adobe.ARM.[...].plist Support
[failed] com.facebook.videochat.[redacted].plist Support
[failed] com.google.keystone.agent.plist Support
User Login Items: ?
MediaCentral Launcher
ChaxHelperApp
TheTube Helper
fuspredownloader
HP Scheduler
Internet Plug-ins: ?
Google Earth Web Plug-in: Version: 6.0 Support
Default Browser: Version: 537 - SDK 10.9
Flip4Mac WMV Plugin: Version: 3.1.0.24 - SDK 10.8 Support
Unity Web Player: Version: UnityPlayer version 4.5.1f3 - SDK 10.6 Support
CouponPrinter-FireFox: Version: Version 1.1.5
FlashPlayer-10.6: Version: 15.0.0.152 - SDK 10.6 Support
DivXBrowserPlugin: Version: 1.4 Support
Flash Player: Version: 15.0.0.152 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
iPhotoPhotocast: Version: 7.0
SharePointBrowserPlugin: Version: 14.2.2 - SDK 10.6 Support
JavaAppletPlugin: Version: Java 7 Update 45 Check version
Audio Plug-ins: ?
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins: ?
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
3rd Party Preference Panes: ?
DivX Support
Flash Player Support
Flip4Mac WMV Support
MediaCentral Support
Time Machine: ?
Mobile backups: ON
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 112.20 GB Disk used: 98.50 GB
Destinations:
Data [Network] (Last used)
Total size: 2 TB
Total number of backups: 24
Oldest backup: ********
Last backup: *****
Size of backup disk: Excellent
Backup size 2 TB > (Disk size 112.20 GB X 3)
Time Machine details may not be accurate.
All volumes being backed up may not be listed.
Top Processes by CPU: ?
4% WindowServer
1% fontd
0% mtmd
0% Activity Monitor
0% ps
Top Processes by Memory: ?
242 MB Safari
106 MB com.apple.IconServicesAgent
102 MB mds_stores
102 MB WindowServer
82 MB Mail
Virtual Memory Information: ?
151 MB Free RAM
1.47 GB Active RAM
1.34 GB Inactive RAM
1.04 GB Wired RAM
554 MB Page-ins
0 B Page-outsMake a "Genius" appointment at an Apple Store, or go to another authorized service provider. You may have to leave the machine there for several days.
Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional—ask if you need guidance.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
*An SSD doesn't need to be zeroed. -
System doesn't boot kernel26beyond
Since a week or so, my system doesn't boot, unless I press <enter> and the power button a few times during the process.
Once it has booted, everything works fine, but it is highly annoying nevertheless.
it seems to have something to do with loading my hardware.
Boot freezes after these log messages:
Jul 23 12:18:49 (none) Linux version 2.6.17-beyond (root@sara) (gcc version 4.1.1) #1 SMP PREEMPT Sat Jul 22 22:14:12 EST 2006
Jul 23 12:18:49 (none) BIOS-provided physical RAM map:
Jul 23 12:18:49 (none) BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Jul 23 12:18:49 (none) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Jul 23 12:18:49 (none) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
Jul 23 12:18:49 (none) BIOS-e820: 0000000000100000 - 000000001ff40000 (usable)
Jul 23 12:18:49 (none) BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data)
Jul 23 12:18:49 (none) BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS)
Jul 23 12:18:49 (none) 0MB HIGHMEM available.
Jul 23 12:18:49 (none) 511MB LOWMEM available.
Jul 23 12:18:49 (none) On node 0 totalpages: 130880
Jul 23 12:18:49 (none) DMA zone: 4096 pages, LIFO batch:0
Jul 23 12:18:49 (none) Normal zone: 126784 pages, LIFO batch:31
Jul 23 12:18:49 (none) DMI 2.3 present.
Jul 23 12:18:49 (none) ACPI: RSDP (v000 ACPIAM ) @ 0x000f5df0
Jul 23 12:18:49 (none) ACPI: RSDT (v001 A M I OEMRSDT 0x09000406 MSFT 0x00000097) @ 0x1ff40000
Jul 23 12:18:49 (none) ACPI: FADT (v001 A M I OEMFACP 0x09000406 MSFT 0x00000097) @ 0x1ff40200
Jul 23 12:18:49 (none) ACPI: OEMB (v001 A M I OEMBIOS 0x09000406 MSFT 0x00000097) @ 0x1ff50040
Jul 23 12:18:49 (none) ACPI: DSDT (v001 1ABSP 1ABSP001 0x00000001 MSFT 0x02000001) @ 0x00000000
Jul 23 12:18:49 (none) ACPI: PM-Timer IO Port: 0x408
Jul 23 12:18:49 (none) Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
Jul 23 12:18:49 (none) Detected 1276.987 MHz processor.
Jul 23 12:18:49 (none) Built 1 zonelists
Jul 23 12:18:49 (none) Kernel command line: root=/dev/hda4 ro
Jul 23 12:18:49 (none) Found and enabled local APIC!
Jul 23 12:18:49 (none) mapped APIC to ffffd000 (fee00000)
Jul 23 12:18:49 (none) Enabling fast FPU save and restore... done.
Jul 23 12:18:49 (none) Enabling unmasked SIMD FPU exception support... done.
Jul 23 12:18:49 (none) Initializing CPU#0
Jul 23 12:18:49 (none) Event source pit configured with caps set: 07
Jul 23 12:18:49 (none) PID hash table entries: 2048 (order: 11, 8192 bytes)
Jul 23 12:18:49 (none) Console: colour VGA+ 80x25
Jul 23 12:18:49 (none) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Jul 23 12:18:49 (none) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Jul 23 12:18:49 (none) Memory: 514844k/523520k available (1921k kernel code, 8120k reserved, 725k data, 184k init, 0k highmem)
Jul 23 12:18:49 (none) Checking if this processor honours the WP bit even in supervisor mode... Ok.
Jul 23 12:18:49 (none) Calibrating delay using timer specific routine.. 2197.93 BogoMIPS (lpj=1098965)
Jul 23 12:18:49 (none) Security Framework v1.0.0 initialized
Jul 23 12:18:49 (none) Mount-cache hash table entries: 512
Jul 23 12:18:49 (none) CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000 00000180 00000000 00000000
Jul 23 12:18:49 (none) CPU: After vendor identify, caps: afe9fbbf 00000000 00000000 00000000 00000180 00000000 00000000
Jul 23 12:18:49 (none) CPU: L1 I cache: 32K, L1 D cache: 32K
Jul 23 12:18:49 (none) CPU: L2 cache: 2048K
Jul 23 12:18:49 (none) CPU: After all inits, caps: afe9fbbf 00000000 00000000 00000040 00000180 00000000 00000000
Jul 23 12:18:49 (none) Intel machine check architecture supported.
Jul 23 12:18:49 (none) Intel machine check reporting enabled on CPU#0.
Jul 23 12:18:49 (none) Checking 'hlt' instruction... OK.
Jul 23 12:18:49 (none) SMP alternatives: switching to UP code
Jul 23 12:18:49 (none) Freeing SMP alternatives: 16k freed
Jul 23 12:18:49 (none) checking if image is initramfs... it is
Jul 23 12:18:49 (none) Freeing initrd memory: 404k freed
Jul 23 12:18:49 (none) ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
Jul 23 12:18:49 (none) ACPI: setting ELCR to 0200 (from 0c30)
Jul 23 12:18:49 (none) CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
Jul 23 12:18:49 (none) SMP motherboard not detected.
Jul 23 12:18:49 (none) lapic max_delta_ns: 1345393639
Jul 23 12:18:49 (none) Event source pit new caps set: 01
Jul 23 12:18:49 (none) Event source lapic configured with caps set: 06
Jul 23 12:18:49 (none) Brought up 1 CPUs
Jul 23 12:18:49 (none) migration_cost=0
Jul 23 12:18:49 (none) NET: Registered protocol family 16
Jul 23 12:18:49 (none) ACPI: bus type pci registered
Jul 23 12:18:49 (none) PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
Jul 23 12:18:49 (none) Setting up standard PCI resources
Jul 23 12:18:49 (none) ACPI: Subsystem revision 20060127
Jul 23 12:18:49 (none) ACPI Error (evregion-0303): No handler for Region [ECOR] (dff2e63c) [EmbeddedControl] [20060127]
Jul 23 12:18:49 (none) ACPI Error (exfldio-0279): Region EmbeddedControl(3) has no handler [20060127]
Jul 23 12:18:49 (none) ACPI Error (psparse-0517): Method parse/execution failed [_SB_.PCI0.SBRG.EC0_.ACS_] (Node dff27900), AE_NOT_EXIST
Jul 23 12:18:49 (none) ACPI Error (psparse-0517): Method parse/execution failed [_SB_.AC__._INI] (Node dff27420), AE_NOT_EXIST
Jul 23 12:18:49 (none) ACPI: Interpreter enabled
Jul 23 12:18:49 (none) ACPI: Using PIC for interrupt routing
Jul 23 12:18:49 (none) ACPI: PCI Root Bridge [PCI0] (0000:00)
Jul 23 12:18:49 (none) PCI: Probing PCI hardware (bus 00)
Jul 23 12:18:49 (none) ACPI Error (evregion-0303): No handler for Region [ECOR] (dff2e63c) [EmbeddedControl] [20060127]
Jul 23 12:18:49 (none) ACPI Error (exfldio-0279): Region EmbeddedControl(3) has no handler [20060127]
Jul 23 12:18:49 (none) ACPI Error (psparse-0517): Method parse/execution failed [_SB_.PCI0.SBRG.EC0_.BATS] (Node dff278e0), AE_NOT_EXIST
Jul 23 12:18:49 (none) ACPI Error (psparse-0517): Method parse/execution failed [_SB_.BAT0._STA] (Node dff245c0), AE_NOT_EXIST
Jul 23 12:18:49 (none) ACPI Error (uteval-0158): Method execution failed [_SB_.BAT0._STA] (Node dff245c0), AE_NOT_EXIST
Jul 23 12:18:49 (none) PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
Jul 23 12:18:49 (none) PCI quirk: region 0500-053f claimed by ICH4 GPIO
Jul 23 12:18:49 (none) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Jul 23 12:18:49 (none) Boot video device is 0000:01:00.0
Jul 23 12:18:49 (none) PCI: Transparent bridge - 0000:00:1e.0
Jul 23 12:18:49 (none) PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Jul 23 12:18:49 (none) Please report the result to linux-kernel to fix this permanently
Jul 23 12:18:49 (none) PCI: Bus #07 (-#0a) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Jul 23 12:18:49 (none) Please report the result to linux-kernel to fix this permanently
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
Jul 23 12:18:49 (none) ACPI: Embedded Controller [EC0] (gpe 28) interrupt mode.
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Routing Table [_SB_.PCI0.P0P2._PRT]
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Routing Table [_SB_.PCI0.P0P1._PRT]
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12)
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 11 12)
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKC] (IRQs *10 12)
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKD] (IRQs *5 6 10)
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKE] (IRQs 6 11) *0, disabled.
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 7) *0, disabled.
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7) *0, disabled.
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKH] (IRQs 4 6 *10 12)
Jul 23 12:18:49 (none) Linux Plug and Play Support v0.97 (c) Adam Belay
Jul 23 12:18:49 (none) pnp: PnP ACPI init
Jul 23 12:18:49 (none) pnp: PnP ACPI: found 15 devices
Jul 23 12:18:49 (none) SCSI subsystem initialized
Jul 23 12:18:49 (none) PCI: Using ACPI for IRQ routing
Jul 23 12:18:49 (none) PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Jul 23 12:18:49 (none) pnp: 00:09: ioport range 0x480-0x48f has been reserved
Jul 23 12:18:49 (none) pnp: 00:09: ioport range 0x5c0-0x5cf has been reserved
Jul 23 12:18:49 (none) pnp: 00:0d: ioport range 0x540-0x55f has been reserved
Jul 23 12:18:49 (none) pnp: 00:0d: ioport range 0x400-0x47f could not be reserved
Jul 23 12:18:49 (none) pnp: 00:0d: ioport range 0x480-0x48f has been reserved
Jul 23 12:18:49 (none) pnp: 00:0d: ioport range 0x500-0x53f has been reserved
Jul 23 12:18:49 (none) pnp: 00:0d: ioport range 0x4c0-0x4cf has been reserved
Jul 23 12:18:49 (none) PCI: Bridge: 0000:00:01.0
Jul 23 12:18:49 (none) IO window: d000-dfff
Jul 23 12:18:49 (none) MEM window: ff800000-ff8fffff
Jul 23 12:18:49 (none) PREFETCH window: ce900000-de9fffff
Jul 23 12:18:49 (none) PCI: Bus 3, cardbus bridge: 0000:02:01.0
Jul 23 12:18:49 (none) IO window: 00001000-000010ff
Jul 23 12:18:49 (none) IO window: 00001400-000014ff
Jul 23 12:18:49 (none) PREFETCH window: 32000000-33ffffff
Jul 23 12:18:49 (none) MEM window: 34000000-35ffffff
Jul 23 12:18:49 (none) PCI: Bus 7, cardbus bridge: 0000:02:01.1
Jul 23 12:18:49 (none) IO window: 00001800-000018ff
Jul 23 12:18:49 (none) IO window: 00001c00-00001cff
Jul 23 12:18:49 (none) PREFETCH window: 36000000-37ffffff
Jul 23 12:18:49 (none) MEM window: 38000000-39ffffff
Jul 23 12:18:49 (none) PCI: Bridge: 0000:00:1e.0
Jul 23 12:18:49 (none) IO window: 1000-1fff
Jul 23 12:18:49 (none) MEM window: ff900000-ff9fffff
Jul 23 12:18:49 (none) PREFETCH window: dea00000-deafffff
Jul 23 12:18:49 (none) PCI: Enabling device 0000:00:1e.0 (0106 -> 0107)
Jul 23 12:18:49 (none) PCI: Setting latency timer of device 0000:00:1e.0 to 64
Jul 23 12:18:49 (none) PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
Jul 23 12:18:49 (none) PCI: setting IRQ 4 as level-triggered
Jul 23 12:18:49 (none) ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
Jul 23 12:18:49 (none) PCI: Setting latency timer of device 0000:02:01.0 to 64
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Jul 23 12:18:49 (none) PCI: setting IRQ 11 as level-triggered
Jul 23 12:18:49 (none) ACPI: PCI Interrupt 0000:02:01.1[B] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Jul 23 12:18:49 (none) PCI: Setting latency timer of device 0000:02:01.1 to 64
Jul 23 12:18:49 (none) NET: Registered protocol family 2
Jul 23 12:18:49 (none) IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
Jul 23 12:18:49 (none) TCP established hash table entries: 16384 (order: 5, 196608 bytes)
Jul 23 12:18:49 (none) TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
Jul 23 12:18:49 (none) TCP: Hash tables configured (established 16384 bind 8192)
Jul 23 12:18:49 (none) TCP reno registered
Jul 23 12:18:49 (none) apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
Jul 23 12:18:49 (none) apm: overridden by ACPI.
Jul 23 12:18:49 (none) VFS: Disk quotas dquot_6.5.1
Jul 23 12:18:49 (none) Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Jul 23 12:18:49 (none) Installing knfsd (copyright (C) 1996 [email protected]).
Jul 23 12:18:49 (none) Initializing Cryptographic API
Jul 23 12:18:49 (none) io scheduler noop registered
Jul 23 12:18:49 (none) io scheduler anticipatory registered
Jul 23 12:18:49 (none) io scheduler deadline registered
Jul 23 12:18:49 (none) io scheduler cfq registered (default)
Jul 23 12:18:49 (none) vesafb: ATI Technologies Inc., P10 , 01.00 (OEM: ATI MOBILITY RADEON 9600 )
Jul 23 12:18:49 (none) vesafb: VBE version: 2.0
Jul 23 12:18:49 (none) vesafb: protected mode interface info at c000:5680
Jul 23 12:18:49 (none) vesafb: pmi: set display start = c00c56ee, set palette = c00c5728
Jul 23 12:18:49 (none) vesafb: pmi: ports = d810 d816 d854 d838 d83c d85c d800 d804 d8b0 d8b2 d8b4
Jul 23 12:18:49 (none) vesafb: no monitor limits have been set
Jul 23 12:18:49 (none) vesafb: scrolling: redraw
Jul 23 12:18:49 (none) Console: switching to colour frame buffer device 128x48
Jul 23 12:18:49 (none) vesafb: framebuffer at 0xd0000000, mapped to 0xe0880000, using 6144k, total 65536k
Jul 23 12:18:49 (none) fb0: VESA VGA frame buffer device
Jul 23 12:18:49 (none) ACPI: AC Adapter [AC] (on-line)
Jul 23 12:18:49 (none) ACPI: Battery Slot [BAT0] (battery present)
Jul 23 12:18:49 (none) ACPI: Battery Slot [BAT1] (battery absent)
Jul 23 12:18:49 (none) ACPI: Power Button (FF) [PWRF]
Jul 23 12:18:49 (none) ACPI: Lid Switch [LID]
Jul 23 12:18:49 (none) ACPI: Sleep Button (CM) [SLPB]
Jul 23 12:18:49 (none) ACPI: Power Button (CM) [PWRB]
Jul 23 12:18:49 (none) ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
Jul 23 12:18:49 (none) ACPI: CPU0 (power states: C1[C1] C2[C2])
Jul 23 12:18:49 (none) ACPI: Thermal Zone [THRM] (94 C)
Jul 23 12:18:49 (none) isapnp: Scanning for PnP cards...
Jul 23 12:18:49 (none) isapnp: No Plug & Play device found
Jul 23 12:18:49 (none) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Jul 23 12:18:49 (none) serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
Jul 23 12:18:49 (none) ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
Jul 23 12:18:49 (none) floppy0: no floppy controllers found
Jul 23 12:18:49 (none) RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Jul 23 12:18:49 (none) loop: loaded (max 8 devices)
Jul 23 12:18:49 (none) PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12
Jul 23 12:18:49 (none) i8042.c: Detected active multiplexing controller, rev 1.1.
Jul 23 12:18:49 (none) serio: i8042 AUX0 port at 0x60,0x64 irq 12
Jul 23 12:18:49 (none) serio: i8042 AUX1 port at 0x60,0x64 irq 12
Jul 23 12:18:49 (none) serio: i8042 AUX2 port at 0x60,0x64 irq 12
Jul 23 12:18:49 (none) serio: i8042 AUX3 port at 0x60,0x64 irq 12
Jul 23 12:18:49 (none) serio: i8042 KBD port at 0x60,0x64 irq 1
Jul 23 12:18:49 (none) mice: PS/2 mouse device common for all mice
Jul 23 12:18:49 (none) TCP bic registered
Jul 23 12:18:49 (none) NET: Registered protocol family 1
Jul 23 12:18:49 (none) NET: Registered protocol family 17
Jul 23 12:18:49 (none) Using IPI No-Shortcut mode
Jul 23 12:18:49 (none) Suspend2 Core.
Jul 23 12:18:49 (none) Time: tsc clocksource has been installed.
Jul 23 12:18:49 (none) Suspend2 Compression Driver loading.
Jul 23 12:18:49 (none) Time: acpi_pm clocksource has been installed.
Jul 23 12:18:49 (none) Event source pit disabled
Jul 23 12:18:49 (none) Event source lapic configured with caps set: 08
Jul 23 12:18:49 (none) hrtimers: Switched to high resolution mode CPU 0
Jul 23 12:18:49 (none) Suspend2 Encryption Driver loading.
Jul 23 12:18:49 (none) Suspend2 Swap Writer loading.
Jul 23 12:18:49 (none) Suspend2 FileWriter loading.
Jul 23 12:18:49 (none) ACPI wakeup devices:
Jul 23 12:18:49 (none) SMBS MODM P0P2 CBC1 USB1 USB2 USB3
Jul 23 12:18:49 (none) ACPI: (supports S0 S3 S4 S5)
Jul 23 12:18:49 (none) Freeing unused kernel memory: 184k freed
Jul 23 12:18:49 (none) input: AT Translated Set 2 keyboard as /class/input/input0
Jul 23 12:18:49 (none) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Jul 23 12:18:49 (none) ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jul 23 12:18:49 (none) ICH4: IDE controller at PCI slot 0000:00:1f.1
Jul 23 12:18:49 (none) PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
Jul 23 12:18:49 (none) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
Jul 23 12:18:49 (none) PCI: setting IRQ 10 as level-triggered
Jul 23 12:18:49 (none) ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
Jul 23 12:18:49 (none) ICH4: chipset revision 3
Jul 23 12:18:49 (none) ICH4: not 100% native mode: will probe irqs later
Jul 23 12:18:49 (none) ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
Jul 23 12:18:49 (none) ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Jul 23 12:18:49 (none) Probing IDE interface ide0...
Jul 23 12:18:49 (none) Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
Jul 23 12:18:49 (none) input: SynPS/2 Synaptics TouchPad as /class/input/input1
Then I have to press enter and the powerbutton (asus M6) a few times, and then, a line at a time a couple of messages appear, then after "udev events" has passed, boot proceeds normally.
Jul 23 12:18:49 (none) hda: IC25N060ATMR04-0, ATA DISK drive
Jul 23 12:18:49 (none) ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jul 23 12:18:49 (none) Probing IDE interface ide1...
Jul 23 12:18:49 (none) hdc: MATSHITADVD-RAM UJ-830S, ATAPI CD/DVD-ROM drive
Jul 23 12:18:49 (none) ide1 at 0x170-0x177,0x376 on irq 15
Jul 23 12:18:49 (none) hda: max request size: 512KiB
Jul 23 12:18:49 (none) hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
Jul 23 12:18:49 (none) hda: cache flushes supported
Jul 23 12:18:49 (none) hda: hda1 hda2 <hda5> hda3 hda4
Jul 23 12:18:49 (none) hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Jul 23 12:18:49 (none) Uniform CD-ROM driver Revision: 3.20
Jul 23 12:18:49 (none) kjournald starting. Commit interval 5 seconds
Jul 23 12:18:49 (none) EXT3-fs: mounted filesystem with ordered data mode.
Jul 23 12:18:49 (none) usbcore: registered new driver usbfs
Jul 23 12:18:49 (none) usbcore: registered new driver hub
Jul 23 12:18:49 (none) Initializing USB Mass Storage driver...
Jul 23 12:18:49 (none) usbcore: registered new driver usb-storage
Jul 23 12:18:49 (none) USB Mass Storage support registered.
Jul 23 12:18:49 (none) Linux agpgart interface v0.101 (c) Dave Jones
Jul 23 12:18:49 (none) fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
Jul 23 12:18:49 (none) [fglrx] Maximum main memory to use for locked dma buffers: 431 MBytes.
Jul 23 12:18:49 (none) [fglrx] module loaded - fglrx 8.26.18 [Jun 22 2006] on minor 0
Jul 23 12:18:49 (none) usbcore: registered new driver usblp
Jul 23 12:18:49 (none) drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Jul 23 12:18:49 (none) Capability LSM initialized
Jul 23 12:18:49 (none) fuse init (API version 7.6)
Jul 23 12:18:49 (none) input: PC Speaker as /class/input/input2
Jul 23 12:18:49 (none) NET: Registered protocol family 23
Jul 23 12:18:49 (none) nsc-ircc, chip->init
Jul 23 12:18:49 (none) nsc-ircc, Found chip at base=0x02e
Jul 23 12:18:49 (none) nsc-ircc, driver loaded (Dag Brattli)
Jul 23 12:18:49 (none) nsc_ircc_open(), can't get iobase of 0x2f8
Jul 23 12:18:49 (none) nsc-ircc, Found chip at base=0x02e
Jul 23 12:18:49 (none) nsc-ircc, driver loaded (Dag Brattli)
Jul 23 12:18:49 (none) nsc_ircc_open(), can't get iobase of 0x2f8
Jul 23 12:18:49 (none) pnp: Device 00:07 disabled.
I am using mkinitcpio already: /boot/grub/menu.lst:
# (0) Arch Linux
title Arch Linux
root (hd0,2)
kernel /vmlinuz26beyond root=/dev/hda4 ro
initrd /kernel26beyond.img
my /etc/mkinitcpio.conf:
MODULES=""
BINARIES=""
FILES=""
HOOKS="base udev autodetect ide filesystems"
I tried removing scsi and sata, since my root is on an ide disk. But the problem persists.
also recreating an image using mkinitcpio or reinstalling the kernel26beyond package using pacman doesn't help.
Does anyone have any idea what might be wrong and how this problem might be resolved.
It seems like a trivial issue since the systems basically works fine otherwise. However, I can't figure it out by myself, I have tried for a week.
Any help would be greatly appreciated.I'm not sure if this will help you, but I suddenly was having a lot of trouble booting. My system would just freeze with a blinking cursor. I thought it had something to do with my floppy drive because if I changed the boot priority in my bios to boot from the hard disk 1st, the system would boot but would hang for a very long time in areas, and as long as 5 minutes loading uevents. I suspected this was a udev problem.
I issued a few commands to reset udev, thinking maybe recent updates didn't take effect, which did the trick...
# udevtrigger
# udevcontrol reload_rules
After that, everything is back to normal. I'm still learning about udev and I'm still fuzzy about a lot of the techy stuff. -
my 80gb IPod doesn't boot up this morning. Worked great last nite. The apple logo keeps coming up for a few seconds then you hear it "wind down" and got blank. Tried reseting multiple time - doesn't work. Ideas?
my 80gb IPod doesn't boot up this morning. Worked great last nite. The apple logo keeps coming up for a few seconds then you hear it "wind down" and got blank. Tried reseting multiple time - doesn't work. Ideas?
-
Tecra S1 doesn't boot and hangs at (boot) splash screen
Tecra S1 Model PT831E-107EQ-GR
Problems started a month ago. It randomly didn't booted. After some power off/on tries it finally booted and worked properly. Because it happened more often I've bought a new hard drive (Toshiba 40 GB). I've had Acronis True Image and planned to make a disk clone to the new drive. The problem is that a notebook now doesn't boot anymore so I cannot boot it from A CD nor hard drive. It stops at "In Touch..." logo with "Press [F12] for the boot device selection menu" text and doesn't react any key. I tried to boot with no CD, no hard drive - the same. I also connected internal HD using ATA-To-USB adapter - the same. Does it mean that's not a disk problem but motherboard or other components? Is it possible to enter BIOS before boot selection screen?
Regards,
JacekProblem solved. There was a broken PCB under the CPU socket. I've found that pressing with my finger and holding CPU while booting allowed to startup the system while releasing the finger caused system hanging and its total crash. Our local service tried to repair it but with no success. Finally two days ago we've found a working motherboard (a used one) for about 200 USD and now I'm waiting for installing it in the laptop. Th regular price for a new one (about 400 Euro) is too much, but 200 USD is OK. I do like the laptop because of its ports (LPT, RS232). It's used for programming and controlling some older devices. Newer laptops have no LPTs nor RS232s and it's not easy to find a working USB adapter because the software we're using is even from DOS times and has hard-coded IRQs for those ports.
Anyway, I hope it'll back from the service fresh and new, and of course working ;)
Thank you for your tips.
Regards,
Jacek -
Hi,
I just bought a broken iBook G4 on eBay thinking I would be able to fix it without replacing the logic board. The iBook doesn't boot properly. When I press the power button, I can hear the SuperDrive start up, then the screen with the gray Apple shows up and the OS starts to load normally. But when that screen goes away and the blue background comes up, it just stops there... no "Loading Mac OS X" window with the progress bar. I figured that this may have been a deviation of the iBook G4 logic board problem where people used clamps to pin down the left side of the iBook and hold the faulty chip to the logic board, allowing the iBook to boot. I gave it a shot, but instead of using clamps I tried putting a small rubber shim on top of the faulty chip inside of the case to see if it would work. The first time I booted it up after I placed the shim, it worked fantastically. No hanging at the loading screen, no sluggish performance.
That was the way it worked for a couple of days. However, the booting problem soon returned. I tried booting from a Tiger reinstall disk to verify/repair the disk/permissions, but the iBook hung at the same blue screen. I didn't have the original install discs that came with the iBook, so I couldn't run a hardware test on it. I also tried booting from a Leopard install disk to no avail. Resetting the PRAM, NVRAM, and PMU did nothing as well. I even went so far as to replace the RAM in the expansion slot with RAM that I knew was working, but the iBook remained broken.
The strangest part of this was that the iBook worked perfectly on another computer when put into TDM. I was able to verify/repair both permissions and the disk from my Power Mac G5. Even though the iBook's screen becomes scrambled with random colors and lines after a few minutes in TDM, it functions just fine on another computer. I was even able to successfully boot my Power Mac and iMac from the iBook in TDM. Seeing as this was possible, I tried reinstalling Tiger on the iBook (in TDM) remotely from my Power Mac. It worked like a charm. Following that reinstall, I downloaded and installed all of the software updates. Then I tried to boot the iBook natively again, but to no avail. It still hung at that same blue screen.
At this point, I suspect that there is something wrong with the logic board that I am unable to fix without completely replacing the logic board itself. That's sort of disappointing, but I guess that's just the way it is. If anyone has any input to this, feel free to respond. Here are the iBook's specs:
CPU: 1Ghz (1064Mhz)
RAM: 256MB soldered, 1 expansion slot open
HDD: 30GB 4200 rpm
Screen Size: 12 inches
Optical Drive: Combo Drive
For the complete list of specs, see this page: http://support.apple.com/specs/iBook/iBookG4_Early2004.html
Thanks,
-TrevorTrevor,
I just took the heatsink off and I see the GPU. However, there are multiple parts to it.
So that would be called a daughter card. The problem with a daughter card is that the possibility of a reballing/reflowing failure is increased.
Should I place a shim over the whole chip or just one part of it?
It's that whole daughter card that has the problem. I've got a post around here somewhere. Here's the thread:
http://discussions.apple.com/thread.jspa?messageID=6051715�
The picture is here:
http://tinyurl.com/3835w2
Also, what material should I use for a shim here?
Probably the most elegant solution would be to use thermal pads like the ones that are already there. Don't build them up too much.
What about from underneath?
My fear is that a metal shim will short the GPU and damage the logic board permanently. But I also fear that an insulating shim will not conduct heat as it is supposed to and cause the GPU to overheat.
Dale at Superior says that chip doesn't put out much heat but better to be overly cautious. I wouldn't use metal since there's no give to it. What's directly under that 9200 daughter card? One of my thoughts was to shim from both sides.
Where did you put that first shim?
Richard -
Help please, my macbook pro model A 1226 doesn't boot up, i hear the optical drive sound starting but no screen light or booting sound, ive'd tried all redet commands, and safe mode but no luck, can anyone give me an solution to my problem. Tnx
It looks as if there's a problem with your GPU. With a Retina machine, that would mean replacement of just about everything, except, perhaps, the flash storage drive.
Print you kernel panic when you go to your Apple Store appointment. I'm betting that it's a faulty GPU but they will be able to diagnose exactly where the problem lies.
Good luck,
Clinton -
Mac doesn't boot after splitting BOOTCAMP drive under Windows 8.1
Macbook pro mid 2012, OS X Mavericks
I've installed Windows 8.1 x64 using Bootcamp assistant. In Windows I went to Disk Management and shrank drive C: from 200 GB to 94 GB and created a new drive D: from unallocated space.
After restart Windows doesn't boot giving some error and quickly restart. If I hold "Option" key I see only Windows. Mac OS X disappeared.
How to fix?So, I've tried 1001 ways to recover. Nothing worked. Interned Recovery gives -2002F error. Macbook pro 2012 can't boot from bootable DVD to use DiskWarrior, Drive Genius or similar. It can't boot from OS X Lion install DVD. I had only Windows PC to fix this. So
I asked a friend with latest Mavericks(which I had too) to make a Recovery USB and make a DMG file from it and send me over internet. Then I used the TransMac application under Windows and burned DMG on my USB stick. My god it worked. After 2 days of struggle I found this solution. I was able to boot from this USB stick into Recovery Mode and from there I can reinstall Mac Os X Mavericks. Somehow it sees my Ethernet cable and doesn't give error.
Note: that Disk Utility wasn't able to recover partitions. I tried to run DiskWarrior from terminal but it gave me an error. TestDisk didn't run too. So I'm doing a clean installation.
I could recover or backup my files using Paragon Mac Recovery Bootable DVD, but there was no need since it's my new macbook and I didn't have much files there.
Windows had changed the HD partition map from GUID Partition Table(GPD) to MBR. And made HD a "dynamic disk". This is why Mac Os wasn't able to boot.
If anyone knows how to convert a disk back to GPD and make Mac OS able to boot please let me know. I'm still installing Mac Os X on USB stick and didn't change my HD. -
HP Stream 7-Windows 10 doesn't boot, I can't recovery 8.1 because can't boot from USB-HELP please!!
Hi everybody, I'm new here!
I am (scuse me: WAS) enjoying a Stream 7
Some days ago I tried to install Windows 10 TP upgrading 8.1 with Bing. After some waiting time it succeeded, but unfortunately I forgave to put in the tablet's SSD the hp drivers, thinking they weren't necessary. So touchscreen, WiFi and all the other stuff didn't work. After I collegated via OTG a keyboard and a mouse I managed to use Windows 10.
Trying to install drivers, my fault, I opened an .exe of Realtek (maybe for the audio), tablet asked to reboot and after that I cannot access to Windows anymore.
I tried to boot Windows 8.1 from a USB, but it doesn't boot, the same even if i disable secure boot.
With disabled bitlocker Windows gives this error
In boot option I set these settings
I put the usb in this way:
The Stream doesn't consider the USB absolutely XD
If I enable again the secure boot Windows gives this error (that at 99% is caused by the .exe I installed):
Rebooting the Stream a couple of time with secure boot it goes in a menu (where touchscreen works) where there are a lot of options to reset Windows, but none of them works. If I try to format from this menu it asks for my account's password, but it doesn't accepts the mine :/
If I try to open the recovery (from volume minus button when it starts) it gives this message:
Waiting for help,
Thank you for your patience!
This question was solved.
View Solution.Hi everyone. I think I have found a solution to this problem. Short background story, I too tried to install Windows 10 (10049) via Windows Update but I was never successful - got stuck at around 30% for more than an hour. I tried to restore to 8.1 but it gave me that 0xc000000f error. Luckily I had made a recovery image to USB before updating to Windows 10.
Please note that by doing this method, you will obviously lose your data.
Here's what you'll need:
- Recovery USB (if you don't have one, grab it from this link and I thank you that person from another post). Follow the instructions, this is just basically clean, format to FAT32, set primary and active, and then drag and drop the files and folders from the USB folder to the root USB drive. This particular recovery is from a 5701 model, there is actually no difference between Stream 7 models in terms of hardware, but software is configured differently (different language setup/format) depending on the country/region it's sold.
- OTG cable
- Powered USB hub
- USB Mouse and Keyboard
- A moment of your time
1. Plug in the OTG cable to the tablet, and then plug in the USB hub to power and to the OTG. After that, plug in the USB mouse and keyboard and Recovery USB to the USB hub.
2. Boot the tablet to BIOS by holding down Power + Volume Down at the same time, until you reach the Startup Menu.
3. Press F10 and navigate to System Configuration > Boot Options. In this menu, we'll have to restore the settings to default.
So if you have disabled Secure Boot, you first need to Clear All Secure Boot Keys and then Load HP Factory Default Keys. Then enable Secure Boot.
Make sure UEFI Boot Order is also default to as follows: OS boot Manager, USB Diskette, USB CD/DVD, Network Adapter.
If you did not make any changes, proceed to 4.
4. Be prepared to go back to the Startup Menu, because as soon as you press F10 and hit Yes, the tablet will automatically restart. So press and hold the Volume Down button after you hit on Yes.
5. Press F9 and select Boot From EFI File. If you've done the recovery image ghosting correctly onto the Recovery USB, you should see two entries. One should be RECOVERY and the other may depend (it could be SYSTEM or No label). Select RECOVERY, and then select bootmgr.efi.
At this point the tablet will boot off from the USB and will bring you to Windows Recovery.
6. Select your keyboard layout, and navigate to Troubleshoot > Reset your PC.
If the drive partition/boot manager is not damaged, it will ask for a recovery key. You can actually skip this step and hide the numpad, revealing the option Skip this drive if you don't have the recovery key anymore, or just really want to start anew.
If the drive partition/boot manager is damaged, the Reset will proceed and will ask you to select a target operating system. In my case it was Windows 8.1.
7. The next screen will be about Reset your PC telling you what's going to happen. Tap Yes > Yes, repartition the drives > Fully clean the drive > Reset.
The tablet will now do its thing and restore to factory default.
After restoration, a BIOS screen will come up asking if you want to clear the TPM keys. Select Yes, and this will create a new key for the restored installation, bringing you back to a fully factory default tablet.
Notes:
I recommend not installing a generic Windows 8.1 ISO that is copied straight to the USB drive using the Windows 7 USB/DVD Tool or RUFUS. They won't be compressed or the same as WIMBOOT, which will take up more storage space than stock recovery.
You could actually install another version of Windows 8.1 on the tablet, assuming you know what you are doing (ie. making a WIMBOOT image).
You could also actually install Windows Technical Preview directly, again, assuming you know what you are doing.
This is just a guide to help you try recover your tablet from a failed Technical Preview installation. I hold no responsiblities over your actions.
What I recommend is that use 8.1 for now, and wait for the official release (or at least a more stable Technical Preview release for this tablet if you can't wait that long) of Windows 10. -
My iBook (1.2Ghz, late 2004) doesn't boot anymore since yesterday. I treid to reset the battery (by using it until empty, and recharging it) but when my iBook shut dow (when the battery was empty) it didn't boot anymore.
I tried:
-to zap the PRAM (optioncommand+PR)
-to do the hardware test (while holding C)
-to enter open-firmware (optioncommand+OF)
-resettig PMU
neither of these suceeded.
I also don't hear the startup chime.
Is there anything else I can do to try and boot it?
Before this it booted without problems, I don't understand why I can't even get in the open firmware.
alltough my iBook is out of warranty, I suspect this to be a fabrication fault, will I have to pay if I let it repair? (I was planning to buy another MacBook Pro, don't know if I can trust apple products enough to buy them again. This isn't my first problem, I had one of the bad batteries where apple started a exchange program for)The indicator LED's at the bottom of the battery say it has, and the illuminated ring of the adapter is also lit green.
-
IPad doesn't boot!! Apple logo freeze!!
Hello,
I've received one iPad that has been used by one of my Staff Directors. Now this iPad is going to be used by another person, so like ever I've reseted all the content (data, configuration, etc), but now the iPad doesn't boot and it is all the time showing the apple logo (it seems that the reset was fine, at least the process bar arrived to completed it and the iPad rebooted itself).
My Macbook PRO doesn't recognize the iPad when I am connecting it by USB cable, I've tried to hard reset as well with the same result: iPad is freeze booting with the apple logo.
So I can't connect the iPad to my Mac, so my iTunes can't recover the iPad, with the hard reset I obtain the same result...
What can I do? Could you help me, please?
Thanks in advance,
Best regardsFirst try to do a reboot, hold down sleep button until you see the slide to turn off screen. Do that, the hold down sleep button until you see apple logo pops up. If that does not work, then...
Google "put iPad in recovery mode". This should allow you to connect it to iTunes, which should ask if you want to restore your iPad. After that, you may be asked if you want to restore from back up. Say NO, since you want a clean slate.
Maybe you are looking for
-
My Computer will not let me open itunes at all. It tells me that the itunes libary can not be read because it was created by a newer version.
-
hi i just wanted to know what is the phone in Material Girls that is owned my Ava all i know is that it comes in a lot of teenage movies and that it might be a nokia Message Edited by alsmi on 03-Apr-2008 09:36 PM
-
Username and password for SOAP sender call
Hello, does anyone know how to provide the username and password to a SOAP sender call, e.g. XI receives the ws via soap and needs to know which userid and password to check. When you use a SOAP client they use basic authentication which sends the re
-
Hi all I have this code to give dynamic table name in select statement. Is there a way the include structure tak in the value from my parameter value like name1? DATA <b>name1</b>(10) TYPE c VALUE 'ZSTUDGARY'. DATA: BEGIN OF wa OCCURS 0. INCLU
-
I've lost my Guitar Rig as a plug-in in GarageBand
Hello all. First a bit of background. For various reasons I had to re-install Panther 10.3.9 for the time being after trying to install my new Tiger software. This is until my new internet Router turns up (in a MONTH!, thanks BT..). The consequences