MOVED: P6n q6600 g0 OC bio settings tryin to hit 3ghz or more

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=110481.0

board is ay P6N SLI Platinum, V1 heatsink, 5x80mm, runnin chip at 3ghz. Iam I doin this right? Before i go any higher i want to check here first . O ram is Crucial Ballistix 2GB PC2 6400.
Room temp 29c
3ghz idle temp 31c
10min full load core temp .95 shows 58c, 60c, 54c, 52c SPEED fan shows 43c, 44c, 37c, 37c , everest shows 50-56c on load.
how far can i push this g0 chip with air is 60 or 70c load not good?
BIOS setting
dot control off
intel eist off
system clock mode manual
fsb clock 1333
memory clock 1000 should i boast this up more?
cpu ratio 9
dram config auto and should i manual set this?
pci-e freq 100 what about boastin up to 105-110?
cpu voltage 0.0000v
memory volt auto
nb volt 1.275v
sb volt 1.50
fsb vtt volt 6%
spread spectrum config
cpu spread off
pcie spread down spread
cpu ldt spread center spread
ata spread enabled
heres a pic of all programs a GO
http://img46.imageshack.us/img46/8476/3ghzload58clt6.jpg

Similar Messages

P6n q6600 g0 OC bio settings tryin to hit 3ghz or more

Sup guys this is my first msi mb. I updated to bios 1.4 still no brand id on CPUZ with this update. Anyway iam lookin for some oc settings that would bring me to 3ghz my ram is Crucial Ballistix 2GB (PC2 6400), I have v1 heatsink with 5x80mm fans in the case. right now i have core temp .95 showin chips are runnin at 95,100,91,91 F. when i run speedfan 4.32 showin temp1 84F and all the cores are at 64-69F idle. what problem is showin the truth? lol

board is ay P6N SLI Platinum, V1 heatsink, 5x80mm, runnin chip at 3ghz. Iam I doin this right? Before i go any higher i want to check here first . O ram is Crucial Ballistix 2GB PC2 6400.
Room temp 29c
3ghz idle temp 31c
10min full load core temp .95 shows 58c, 60c, 54c, 52c SPEED fan shows 43c, 44c, 37c, 37c , everest shows 50-56c on load.
how far can i push this g0 chip with air is 60 or 70c load not good?
BIOS setting
dot control off
intel eist off
system clock mode manual
fsb clock 1333
memory clock 1000 should i boast this up more?
cpu ratio 9
dram config auto and should i manual set this?
pci-e freq 100 what about boastin up to 105-110?
cpu voltage 0.0000v
memory volt auto
nb volt 1.275v
sb volt 1.50
fsb vtt volt 6%
spread spectrum config
cpu spread off
pcie spread down spread
cpu ldt spread center spread
ata spread enabled
heres a pic of all programs a GO
http://img46.imageshack.us/img46/8476/3ghzload58clt6.jpg

MOVED: Some further advice on BIOS settings

This topic has been moved to BIOS.
https://forum-en.msi.com/index.php?topic=97654.0

I agree with Osnavi!
You wont note difference in performance if you don't play fairly modern games, and hardly then. Ít is allowance for the g. card to keep very big size pictures in normal memory, you could say. As new g. cards got so much memory onboard, I don't think you need worry whether to have 64 or 128 MB aperture, even if playing modern games.
I have had some bad experiences of Fast write and Radeon cards, though I can't absolutely point to that as a reason. Could be what model of graphics card you got.

MOVED: MSI P43 Neo unsupported bios settings

This topic has been moved to Intel Core 2 Duo/Quad boards.
https://forum-en.msi.com/index.php?topic=124571.0

The processor support 64bit, however, it does not support Virtualization. Technology.
Quote
Then I try to run with Vmware and VirtualPC one operating system x64 but i get the message: "Your CPU not suport x64 operating system"
Are you running VMWare/VirtualPC out of a 32bit operating system? If yes, that explains the error message.
Please try to install a 64 bit operating the regular way, not virtualize it.

MOVED: MSI 990FXA-GD80 V2 BIOS Settings

This topic has been moved to Overclocking, Undervolting.
https://forum-en.msi.com/index.php?topic=164923.0

This topic has been moved to Overclocking, Undervolting.
https://forum-en.msi.com/index.php?topic=164923.0

MOVED: Bios settings for single SATA Drive Help

This topic has been moved to Intel P4/Celeron boards.
https://forum-en.msi.com/index.php?topic=142931.0

Nope. Didn't work.
I can try things all day but this doesn't make sense. Surely someone knows what bios settings are required (especially on the MSI board site) to set the bios on a MSI 945p platnium motherboard. I have the sata drive plugged into the Sata 1 connector and bios still says it is ide channel 4 master. The computer will boot with just the sata drive plugged in but the problems start when I plug the ide drives in on ide 1 or 2 or 3.

MOVED: HDD Is Running In "PIO", Bios Settings?

This topic has been moved to AMD SocketA based board.
HDD Is Running In "PIO", Bios Settings?

Quote from: -Knight- on 29-October-05, 03:40:27
It is a existing system. i've had this pc for 4-5 years, but it was a week ago i noticed this problem, so i dont know if it has ever been in DMA mode.
yes, 80 cond, 40 pins (well,39)
no. i have no other cables to test..
and i just erased the hdd two days ago and i have not installed any other hardwear or changed the cables after that..it's only xp and all the other updates from MS-web, so it's a cleen hdd now..no crap or anything, just up to dates.
but, i'll try to uninstall those IDE channels, be back in 10 min
I noticed on startup somthing like "DMA ...(something).... and S.M.A.R.T enabled" (something like that)
so i guess my bios has the right settings, but still..PIO
also, my IDE (hdd) cable isnot that good-looking (it's been twisted and looks like it's in bad shape), so i think i'll get anotherone soon (today or monday)
then i guess i'll have to run xp in safe mode, uninstall my IDE channels, shut off pc and replace my IDE (hdd) cable with new one, start up and let xp install drivers again..
let's hope!

Ideal KT4V BIOS settings for XP2500+ Barton

I've read AMD's recommendations for the KT4V BIOS settings http://www.amdforums.com/showindex.php?s=&threadid=186506 , but they seem to be very generic. I would like to know the settings that would give me the highest performance, without causing any instability, using my present system and usage. My son does 3D animation and gaming on this computer. This is a stand alone computer (no network). The latest version BIOS for the KT4V offers an option in Power Management Features to enable CPU HALT Command Detection. I heard that this would work better than Cooler XP in cooling the CPU. I enabled it and my CPU Temp dropped 6-10 degrees C. Is this recommended? What is the down side of this action? My system is as follows: AMD Athlon XP 2500+ w/ Vantec VA4-C7040 CPU fan (w/Arctic Silver 3) MSI KT4V mobo Gainward Golden Sample Ti/450 TV w/ 128MB DDR (GeForce3 Ti 200) 2 - Kingston 512MB PC2700 DDR RAM Antec TRUE550 power supply 1 - 40GB 7200RPM hard drive 1 - 30GB 5400RPM hard drive 1 - CD-ROM 1 - CD-RW 1 - floppy drive Windows XP home Any help would be appreciated. Thank you, Barry

As a result of my research, these are the BIOS settings that I am using. My computer runs well and is stable.
* MSI KT4VL BIOS SETTINGS w/AMD XP 2500+ w/ Barton *
==================
Standard CMOS Features
==================
Time Set Correctly Upon first POST and after each BIOS Flash / CMOS Reset
Date Set Correctly Upon first POST and after each BIOS Flash / CMOS Reset
Primary IDE Master
Type AUTO
32Bit transfer Mode ON
Primary IDE Slave
Type AUTO
32 Bit Transfer Mode ON
Secondary IDE MasterType AUTO
32 Bit Transfer Mode ON
Secondary IDE Slave
Type AUTO
32 Bit Transfer Mode ON
Floppy Drive A Set Appropriately
Floppy Drive B Not Installed
Boot Sector Virus Protection Disabled
===================
Advanced BIOS Features
===================
Quick Boot Enabled
Full Screen Logo Show Disabled
Boot Sequence
1st Boot Device Floppy
2nd Boot Device CDROM/DVD whatever you use
3rd Boot Device IDE 0
Try Other Boot Devices No
S.M.A.R.T. for Hard Disks Enabled
BootUp Num-Lock On
Floppy Drive Swap Disabled
Floppy Drive Seek Disabled
Primary Display VGA/EGA
Password Check Setup
Boot to OS/2 No
Internal Cache Enabled
System BIOS Cacheable Disabled
C000,32k Shadow Disabled
APIC Function Enabled
MPS Table Version 1.4
=======================
Advanced Chipset Features
=======================
DRAM Timing Control
Current Host Clock Displays current FSB Frequency
Configure SDRAM Timing By SPD (Set to User first to change RAM timings)
SDRAM frequency 333 for PC2700 and above
SDRAM CAS# Latency 2
Row Precharge Time 2T
RAS Pulse Width 5T
RAS to CAS Delay 2T
SDRAM Bank Interleave 4-Bank
SDRAM Burst Length 8QW
SDRAM 1T Command Enabled
Fast Command Fast (start here and if Windows installs stable set to Ultra)
Fast R-2-R Turnaround Enabled
AGP timing Control
AGP Mode 4X
AGP Fast Write Disabled
AGP Aperture Size 256MB
AGP Master 1 W/S Write Enabled
AGP Master 1 W/S Read Enabled
AGP Read Synchronization Enabled
PCI Delay Transaction Enabled
========================
Power Management Features
========================
IPCA Function Yes
ACPI Standby State S1/POS
Call VGA at S3 Resuming Disabled
USB Wakeup From S3 Enabled
Power Management/APM Enabled
Power/Sleep LED Single LED
Suspend Time Out (Minute) Disabled
Display Activity Ignore
CPU Critical temperature 70 degrees C CPU HALT Command Detection Disabled
Power Button Function On/Off
After AC Power Loss Power Off
Set WakeUp Events
Wake Up on Ring Disabled
Wake Up on PME Disabled
Resume On KBC Disabled
Wake Up Key Any Key
Wake Up Password N/A
Resume on PS/2 Mouse Disabled
Resume By Alarm Disabled
Alarm Date 15
Alarm Hour 12
Alarm Minute 30
Alarm Second 30
===================
PnP/PCI Configurations
===================
Plug and Play Aware O/S Yes
Clear NVRAM No (Set One time only to Yes After Installing New Hardware or Moving PCI Cards Around)
PCI Latency Timer 64 (Set Higher for better PCI performance reduce if having sound or LAN problems)
PCI IDE BusMaster Enabled
Primary Graphics Adapter AGP for AGP card - PCI for PCI video card)
PCI Slot 1 IRQ Auto
PCI Slot 2/5 IRQ Auto
PCI Slot 3/6 IRQ Auto
PCI Slot 4 IRQ Auto
===================
Integrated Peripherals
===================
Floppy Disk Controller Auto
Serial Port 1 Disabled
Serial Port 2 Disabled
Serial Port 2 Mode Normal
IR Pin Select IRRX/IRTX
Onboard Parallel Port Auto
Parallel Port Mode ECP (For some Printers you may need to set as Bi-Dir or EPP)
EPP version N/A
Parallel Port IRQ Auto
Parallel Port DMA Auto
Onboard Midi Port Disabled
Onchip IDE Controller Both
Onboard LAN Enabled (Disabled if using PCI LAN card)
Onboard LAN PME Enabled (Disabled if using PCI LAN card)
AC’97 Audio Enabled (unless using PCI sound card)
MC’97 Modem Disabled
USB Controller All 6 USB Ports
USB Legacy Support Disabled (some people with legacy USB devices may need to enable)
Port 64/60 Emulation Enabled
===============
PC Health Status
===============
Chassis Intrusion Disabled
CPU Fan Detect Enabled (set to disabled BEFORE shutting down to install any PSU powered CPU fan)
======================
Frequency/Voltage Control
======================
Spread Spectrum Disabled (return to default setting to troubleshoot EMI problems)
CPU FSB Clock 166
CPU Ratio Auto
CPU Vcore (V) Auto
DDR Voltage (V) Auto (set to 1.6 if you have RAM instability)
Termination Voltage Auto
AGP Voltage (V) Auto

MOVED: Back to a previous bios version / P7N Diamond

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=119686.0

Quote
As soon as I update with version 1.2, it is not possible anymore to overclock with EXACTLY keeping the same parameters (see my previous subjects).
Did you clear CMOS with main A/C power cable removed from PSU after flashing the BIOS? If not, please do that and test again. OC settings can vary between BIOS Versions, that is not that unusual.
Quote
Is it possible to return to version 1.1 after flashing to version 1.2 ?
Yes.
Quote
Could you help me ?
>>Use the MSI HQ Forum USB flasher<<
Quote
Or tell me what to do with version 1.2 if I want to go on with overclocking ?
Provide full system specs. >>Posting Guide<< Create a signature with all relevant details about your system so we don't have to ask for it every time you open a new thread.
Also, post the BIOS settings you used with BIOS v1.1 (all of them) and describe your problem in more details.

K8N Neo2 Forgets BIOS Settings??

I'm having a rather odd problem. I built a new PC based around the K8N Neo2 motherboard/Athlon64 3500+. Whenever the switch on the back of the power supply is shut off, and then turned back on, if I don't clear CMOS by moving jumper JBAT1 to the "clear data" setting then back to "keep data" setting, the system won't POST. The diagnostic LEDs on the DBracket go Yellow, Red, Red, Yellow when this happens.
If I clear CMOS by moving the JBAT1 jumper, then the system will POST and it seems to work fine (although I have to reconfigure the BIOS). Also, if the power supply itself hasn't been switched off or lost power, I can turn the PC on and off with the power switch on the front of my case and the system will successfully POST each time without having to move JBAT1.
But it's very annoying, because when the power flips off, I have to move JBAT1 to clear CMOS and reconfigure the BIOS to get the PC going again.
Anyone have any clue as to why the board would act this way?? It's frustrating.

Looks like a bios dmi pool corruption or extended PnP system data
in nvram.
Try this:
Remove the AC cord from the PSU .
Take the bios battery out .
Set jbat cmos jumper to discharge for two hours .
After that time period
mount the battery
Set cmos jumper to normal
Connect AC
Turn PSU on (fire up the pc)
Watch the post screen
You should now get cmos-error .. press F1 to continue .. del to enter bios.
PRESS DEL
Then do only "load optimized defaults" and save/exit with F10 .
Next boot should post that BUILD DMI POOL SUCCESS , UPDATE DMI SUCCESS .
(after this you can change your other bios settings)
If you still have the same problem after this there must be an error
with the motherboard itself.

URGENT HELP NEEDED (Bios Settings Failed)

Hey Guys,
I am having problems with my MSI Board, and don't know what to do. I am very much a noob to BIOS/and modding so I apologize in advance. You guys helped me a few months ago getting everything up and running and all was great for months. Then last night I walked away from my PC for a while and when i came back a starting screen was on saying my OC Settings Failed to load, i tried other versions I saved and they all failed as well. I ended up loading failsafe options, and got the "double start" where the computer turns on, then instantly shuts off, then turns on again. This allowed me to load windows 7, which then started to "install updates". So i think while i was away Windows automatically updated and rebooted... but would that effect my BIOS settings?
As I said, I had my system running perfect for months no errors or crashes at all based on the Bios setting you guys help me with in this thread: https://forum-en.msi.com/index.php?topic=147854.0
However, last week I removed the heat sink and installed this cooler: http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010
All I did was unhook everything from the MB, install the cooler, and then hook everything back up to the MB. The only thing I may have done wrong is not connect the SATA devices (my HDs and ROMS) back in the spots they were in originally. However after I installed the cooler, they system booted right up, and I haven’t had any problems with my system for the past two weeks. I also should note I didnt make any BIOS changes either after I installed the cooler. So I don’t know if I should have done something there. Yet, like I said the system has been fine for the past two weeks, no crashes or errors... it wasn’t until last night after Windows auto updated that this has begun.
The reason I need "URGENT HELP" is because of course I just a new job with deadlines due and so much video editing work I need to do. I would be fine leaving it on failsafe settings, and forgetting the OC setting all together if I new that would make the system stable. But considering its still doing the "double start" even in failsafe mode, im afraid if i start working my system will crash.
So I am begging anybody for any advice or help they could provide. I will provide my system info below. If anybody can guide me as to what settings I should set in BIOS i would appreciate it. Or perhaps there’s a BIOS update that I should use now that I have a cooler and not a heat sink? If you need any more information from me, just ask. I will be monitoring this thread all day, as I desperately need help.
MY SYSTEM:
Intel 980X chip running Win 7 64bit (with MSI BigBang xPower MB installed in my old Dell XPS 730X)
(1) SATA II WD 3gb Hard Drive @ 1.5TB
(2) OCZ SATA II SSD drives @120GB: http://www.newegg.com/Product/Product.aspx?Item=N82E16820227543
(2) Hitachi 6gb SATA III drives @2TB: http://www.newegg.com/Product/Product.aspx?Item=N82E16822145473
3 DVD/CD/BLUERAY DRIVES:
1 SATA DVD DRIVE
1 SATA BlueRay Drive
1 SATA CD Drive
(So 8 SATA Devices Total)
24GIGs of this ram: http://www.newegg.com/Product/Product.aspx?Item=N82E16820145321
1 NVida Geforce GTX 470
1 Soundblaster X-Fi Titanum Card
New Addition Water Cooler: http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010

PROBLEM: My OC BIOS setting wont load. Even on failsafe i get the "double start". I want to get back to my OC (stable) settings.
UPDATE: Since I posted somebody messaged me mentioned I should have "reset the CMOS" after I installed the new cooler. So I did that, and now they system starts fine without the "double start". I am able to load one of my saved OC settings now as well (but any others causes a failure).
NEW QUESTIONS:
1. Since I reset the CMOS and now the system is starting fine on my last OC settings, is it safe to assume the sytem is stable for now?
2. I never made any power changes or BIOS changes after I installed the new cooler. Should I have?
3. After I reset the CMOS was I soupposed to reinstall the drivers from the MSI disk again? I did not, and the system seems to be fine, but I thought I was soupposed to do that after a CMOS reset.
4. Is there a new BIOS version for my setup that may be better now? Im currently on v1.5
Here is a screenshot from CPUZ of the system information currently. This is with it booting normally after my CMOS reboot. I just figured id post it incase it helps with any of my questions. Thanks so much for helping guys!

How to restore default BIOS settings on Toshiba 1410 / 1415 / 2410 laptops? Option to CHGBIOSA?

I have problems booting to any operating system but DOS on Toshiba Satellite 1410 (in very good physical condition) after few years of inactivity (drained down main battery and CMOS battery - now they're charged)
Windows stops with BSOD (error 0x0000008e), Linux stops with kernel panic, bad_area_nosemaphore and IRQ error.
Plain MS-DOS 7.10 seems to run OK.
BIOS was 1.40 with main password set. After first boot it displayed request for entering password and pressing F1 key to set the hardware clock. Now it doesn't display this message anymore.
Two memory modules (Nanya - 256 MB, 266 MHz, CL 2,5) are OK - checked on different versions of MemTest86+
(Windows Memory Diagnostic Tool hangs when starting!)
I dismantled laptop and cleaned very small amount of dust inside with compressed air. Changed thermal paste on the processor (Celeron M 1,8) and bridge. Turned laptop on with extension cards, battery and disk and without them also.
It didn't help.
I flashed the CMOS with BIOS 1.20, 1.30 and 1.40 back again. None of the versions didn't let booting neither Windows nor Linux.
MS-DOS, PC-DOS, FreeDOS still run OK.
What's more interesting - after flashing procedure all BIOS settings were intact (booting priority, battery saving mode, etc.). And yes - I removed the password before flashing!
I was suspicious about problems occuring when laptop was entering 32-bit mode and checked it with Video Memory Stress Test.
When CMOS was flashed with 1.20 BIOS above test was running flawlessly. However, with 1.30 and 1.40 version it stopped >>Unhandled Exceptopn "Access Denied"<< in 8th iteration when lucky. Most of the time it stopped after 2nd or 3rd iteration after framebuffer subtest.
So my question are:
- did CMOS lost its settings or somehow they were corrupted after long period of laptop's inactivity?
- is Video extension of this BIOS flashable?
- why the settings are NOT restored to defaults after each CMOS flashing?
- or maybe there is some hidden switch/option to CHGBIOSA flasher to reset non-flashable CMOS area?
- or is my built-in Video Card (nVidia NV17M) or IRQ enumerator dead?

Hi Jerry! I think I'm on board now, anyway I hope so. I removed both devices and switched them around. The device manager shows two USB devices. One is Mass Storage and one is Composite. I don't realy know which one is the 1TB and which one is the 16 GB. In my boot menu, it just says USB now?? My laptop only has three USB ports. Two on the right and One on the left. I have a wireless mouse plugged in one of the ports on the right as you can see in device manager. I hope this is what you were asking. I can be a little thick headed at times, so let me know what else you want me to try Thank you for your kind reply. It really means a lot to me.
Dokie!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.
Attachments:
Capture40.JPG ‏202 KB
Capture41.JPG ‏137 KB

How do I find the BIOS settings? I'm trying to install a VM so I can run CAD programs for my work.

I am an engineering student and thus having the capability to utilize CAD programs is highly advantageous to me, so I talked to several of my friends who have Macbooks and they recommended using Parallel. After I installed the program and my Windows OS, it keeps giving me an error message saying that the hardware virtualization has been disabled in the BIOS settings. I cannot find the BIOS settings anywhere! How do I change this? Does anyone know?

There are no BIOS settings, because Macs don't have a BIOS. I don't use Parallels, but I assume it has simulated BIOS settings. You'd have to consult its documentation to find out how to change them.

Lenovo G50-30 Unable to access BIOS settings after Windows recovery

Hi
I recently 'downgraded' a recently purchased Lenovo G50-30 with preinstalled Windows 8.1 to Windows 7 using a UEFI USB install on a GPT partition. I also updated the BIOS from A7CN40WW to the latest A7CN43WW and all was working fine. However, after performing a necessary restore of an system image created using the Windows 7 backup and restore tool, I am suddenly unable to access the BIOS settings, either with the novo button (I do get the menu to select BIOS) or with Fn +F2. All that happens is that I receive a blank screen with a static cursor in the upper left corner. I can however still access the boot menu Fn +F12. This is a particular pain as I obviousl can't select USB 3.0 in BIOS.
Any help here would be greatly appreciated.

OK, I managed to clear CMOS by disassembling and desoldering a leg off the the RTC battery but to no avail. The problem seems to be that BIOS a7cn43ww itself has somehow been corupted. In theory this should be able to be resolved by a reflash. The trouble here is there seems to be no way to reflash with a current or previous BIOS version, so I'll have to either wait for a newer version or someone may know better.
C'mon Lenovo support this simply isn't good enough. It's a brand new laptop and I'm considering returning it for a refund.

How to install Windows 7 in UEFI modeand what bios settings for D30

How do you install windows 7 in UEFI mode and what bios settings do I need to install it on a D30 workstation.

Not a ThinkStation guy, but FWIW, that can happen when installing Win 7 in UEFI mode when CSM support is not enabled in BIOS.
Is CSM support - either explicit or by selecting "other OS" and turning UEFI back on as suggested above - an option?
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

MOVED: P6n q6600 g0 OC bio settings tryin to hit 3ghz or more

Similar Messages

Maybe you are looking for