MOVED: P6N Sli Platinum - Problem

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=129611.0

Quote from: HU16E on 14-July-09, 06:00:43
Did you have the system OC'd at all? The crackling you heard 'may' have been a capacitor gone bad. By the CPU, on the NB side I believe, do you see a little 1/4 or so round clear sticker with a number on it? Does it say 01, 02, or 03? I recently retired my P6N, but it was a 'great' board for a number of years. If you want to keep the board, it may have to go in for service. Trying another CPU might damage it too if something is wrong with the boards circuitry. MSI can also do a parts upgrade to the board & make it compatible with 45nm CPU's like the E8400-E8600 from a 01 02 03 revision board.
Hmmmmm...no sticker at all, I check all over the board. This was a newegg purchase in Feb 08' if that can say anything about what version it may be. Also, I did not have the system OC'd at all. Everything was running "as is". The crackle I heard could be better described as when something is being fried. The odd thing is, there was no smells, no busted caps or anything. If I were to replace something first (with new) which would you suggest? I am thinking a new mobo since the mobo I have now could do more harm than good. Or should I get RAM to see if the RAM was fried when my PSU failed? I see 3btech.com has a P6N SLI V2 (what's the V2 mean?) for like $80. Although, if its RAM, it could most definately be a cheaper fix (and I have more ram lol). Again, thanks for the help, it is greatly appreciated!!!

Similar Messages

MOVED: P6N SLI Platinum + Q6600 (B3 Stepping) = No overclocking?

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=110345.0

Quote from: BOSSKILLER on 31-August-07, 20:09:18
It has been tested and no problem to pass 1200Mhz barrier....
Intel® Core™2 Quad Processor Q6600 and corsair 800MHZ memory. OC to 1333MHZ.
memory used in a test:
the first group:Geil 1G 800MHZ
the second group:HyNIX 1G 800MHZ
the third group:Corsar 1G 800MHZ
the forth group:XTreem 1G 800MHZ
the fifth group:Vitesta 1G 800MHZ
If you experience the problem suggest you try with different memory brand/type.
And what stepping/revision Q6600 was this test done with? I've tried with Geil 800mhz rated sticks and Corsair 800mhz sticks in addition to my own personal Buffalo 800mhz sticks and it's all the same. At exactly 1200mhz it's like someone flipped a switch and the board won't POST. The ONLY way I've found to get it to POST past 1200mhz is to increase the VTT to 16% which is a bit worrysome... and with the 1.1 BIOS absolutely no increase in VTT is needed with the same setup. Keep in mind this has been tried with not only my own personal P6N Platinum, but also with two different P6N SLI FI boards I've got here in the shop. Heck I even ordered a brand new one just to test to see if the problem was based on a particular hardware revision.
Very puzzling... ??? ???

MOVED: P6N sli platinum not working

This topic has been moved to Intel Core Duo and Core 2 Duo based boards.
https://forum-en.msi.com/index.php?topic=108834.0

Quote from: Maesus on 03-June-07, 15:44:15
Core 2 Duo will perform WAY BETTER than Pentium 4. It is 100% compatible to Pentium 4. Do you know what Pentium 4 model number you have?
Pentium 4, 3.2 mhz
640 <--this is the model number http://www.intel.com/products/processor_number/chart/pentium4.htm
2m/800fsb
O yes and non of the lights on the D-Bracket go on, the green light and orange light on the P6N are on.

MOVED: P6N SLi platinum, Voltage memory probs

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=111499.0

I've been experimenting a bit and now reached 2.98 Ghz with stock cooler, idle @ 25C, loaded @ 55C
The fsb:dram is 9:8 and mem is now running at 662Mhz, was 638 Mhz????
I cannot set the divider myself unfortunately, or me don't now how to (see specs for info)
One more question( you can put this post in the overclock forum if you like) I want to reach 3Ghz as a max, but as soon as I set fsb on 1500(now 1490) it will boot but within 10 to 30 min orthos will stop.
What do I have to do to get it stable, my mem is running on 1.85V as described by kingston and I raised the NB by .025V, now 1.275V and on 2980Mhz it's rocksolid, no errrors after 5 hours of orthos.
Do i have to raise the Vcore or something else, any comment is welkom
Thanks in advance

MOVED: P6N SLI Platinum [1.4] + DDR2-800 Transcend aXeRAM TX800QLJ-2GK : compatible ?

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=113631.0

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=113631.0

MOVED: P6N SLI Platinum - safe North Bridge voltage

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=114252.0

Thank you as it took care of my occasional lockup while gaming _

P6N Sli Platinum - Problem

Hello! Can you help me... I have Q6600 processor.When changing CPU Multiplier ... always remains 9! C1E - Disabled,EIST - Disabled. Where is my mistake?

Quote from: darkbg on 15-August-09, 14:37:24
CLear CMOS after repeated unsuccessful attempts by the 400 bus with jumper on the motherboard.
What jumper?
I have the same board, but dont know of a jumper.
The only thing I know of is a "fsb hole" between ~1600 and ~1700MHz, got mine at 1720MHz and running stable.

Core 2 Quad Q8400 Problem (P6N SLI Platinum) [FIXED]

Hello, I recently bought an Intel Core 2 Quad Q8400 with the understanding that my P6N SLI Platinum will support Yorkfield cores, given I have the latest BIOS. I updated my BIOS to 1.6, yet it just hangs on the MSI screen and will not POST. I just want to know if I indeed do have the latest BIOS, and if so, if there's anything I or MSI can do to remedy this problem. I really don't have enough money for a new mobo or CPU, and I'm going to be extremely irritated if I just wasted $170 on this... Thanks in advance.

Quote from: alj on 10-November-10, 19:27:09
I'm here for help and complain, no msi is not supposed to know what will be intel releases, but i think they can fix the problem by releasing a new bios or simply put on the boxes models when writing that it support this or that technology
if you searched a little on msi.com you would have ended up here:
www.msi.com/index.php?func=prodcpu2&prod_no=1140&maincat_no=1
here it says what CPU 's the board can run.
so MSI does say, what you can use, but it doesnt say on the box, cause it changes all the time, so they keep an online list.
and no, they cant write a new BIOS, its a chipset limitation from the NVIDIA chipset that cant be overcome by BIOS update unfortunatly.
I would go for a cheap P45 board, they can almost run all s775 CPU's and its newer then the P6N.

MSI P6N SLI Platinum Sound problem

M using MSI P6N SLI Platinum (MS-7350), i am having problem with sound, i have attached 5.1 sound system all speakers are working fine accept front right, may i know what the problem is ? I've Tried everything thet was possible, Head phone, Speaker Wire, etc. etc.

What if you switched the speakers around? Does the signal from front right still missing?

P6N SLI-FI & P6N SLI Platinum

Main purpose for those betas, fix for slowdown issue when using 4GB system memory.
beta BIOS for P6N SLI Platinum ver V1.32:
BIOS Sign-on message: MSI P6N SLI Platinum A7350NMS V1.32 050307 (Date: 05/03/2007)
Attachment name: P6N SLI Platinum BIOS 1.32.zip
beta BIOS for P6N SLI-FI ver V2.22:
BIOS Sign-on message: MSI P6N SLI A7350NMS V2.22 050307 (Date: 05/03/2007)
Attachment name: P6N SLI-FI BIOS 2.22.zip
Make and ensure PC is stable before proceed. flash BIOS from USB key, by using our Tool(easy & safe way to flash):
MSI Forum HQ USB Flashing Tool
Use Beta or Modded BIOSes at own risk!

Quote from: BOSSKILLER on 29-April-07, 00:17:22
Main purpose for those betas, fix for slowdown issue when using 4GB system memory.
beta BIOS for P6N SLI Platinum ver V1.32:
BIOS Sign-on message: MSI P6N SLI Platinum A7350NMS V1.32 050307 (Date: 05/03/2007)
Attachment name: P6N SLI Platinum BIOS 1.32.zip
beta BIOS for P6N SLI-FI ver V2.22:
BIOS Sign-on message: MSI P6N SLI A7350NMS V2.22 050307 (Date: 05/03/2007)
Attachment name: P6N SLI-FI BIOS 2.22.zip
Make and ensure PC is stable before proceed. flash BIOS from USB key, by using our Tool(easy & safe way to flash):
MSI Forum HQ USB Flashing Tool
Use Beta or Modded BIOSes at own risk!
i have the problem with the 4gb upgrade (slow) on winx64. my question is do i have to use this bios ver 1.32 or get the latest and the greatest bios v1.6 for my mobo p6n sli plat?
thanks in advance.
-alex

P6N SLI Platinum random shutdowns

System:
MSI P6N SLI Platinum MoBo
Intel E6750 CPU
Etasis 850W PSU
Corsair CM2X1024-6400C4 RAM (using only 1 stick while troubleshooting)
MSI NX8600GTS GPU
OK, this is a strange one. I put my new system together and everything seemed to be working fine. POST looked OK, and I was even able to install Windows. Everything seemed stable.
One thing that troubled me was that the lights on the D-Bracket were all red AFTER POST. In other words everything was working, but the LEDs were showing CPU problem. I tried everything I could think of to get the lights to go away, but nothing worked. I disconnected all HDs, DVD, and floppy drives. I reset the BIOS, and reseated the CPU. I tried putting RAM in different slots, tried both sticks solo, but nothing made any difference.
It was getting late, so I decided to go to bed and run memtest86+ over night. When I got up this morning the system had powered itself down. When I turned it on again it powered itself off within a minute of being turned on. This was with all the drives hooked up, so I disconnected everything and now it's been sitting happily in the BIOS for over 30 minutes.
So at this point, it seems like it could be a power supply issue. Unfortunately, I don't have another PSU with an 8-pin CPU connector that I can try in this system. Any thoughts? Next steps to try?
Other possibly useful facts:
When I boot into the BIOS the D-Bracket lights show #3 green, and all others red, indicating "initializing keyboard controller". But when I boot past the BIOS to a CDROM or Windows, they show all red, indicating "CPU problem"
The system makes a brief chirp the POST screen. It doesn't sound like a beep code to me, and I've heard some boards will do an "everything's OK" beep like this. But it could be important so there it is.
Although it seems happier with all the drives disconnected (indicating a PSU problem), it still shows all red LEDs on the D-Bracket (indicating a CPU problem).
This is not the first system I've built, and I was fairly careful about putting everything together the right way. The only goof I know of is that at one point I was unplugging and re-plugging things and I ran the system for a while without connecting PCIE power to the GPU. Could that have broken something?
Any help would be much appreciated.
-Steve

UPDATE: I tried hooking up my old 400W PSU with 20-pin ATX and 4-pin CPU connectors (apparently this is OK to do) but there was no change. Still four red LEDs.
I also tried removing the PCI-E GPU and booted it up with an antique PCI VGA card. Again, no change. Maybe I really did get a bad CPU?
Any other ideas, before I try to return my CPU?

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

P6N SLI Platinum crashes from cold boot

Intel Core 2 Duo E6420, 2.13GHz, 1,066FSB, 4MB
Zalman CNPS9500-AT Intel LGA775 Aero Flower Cooler
MSI P6N SLI Platinum
Neste ECS 6001 600 watts PSU (3.3V/24A, +5V/30A, +5VSB/3A, +12V1/18A, +12V2/18A, +12V3/18A, +12V4/18A, -12V/0.5A)
2 x 1GB Crucial PC2-5300 Non ECC CL5
XFX GeForce 8600GTS 256MB DDR3 PCIe (PV-T84G-UDF3)
1 x Western Digital Caviar 160GB 7200rpm, S300, 16MB SATA (system disk)
3 x Western Digital Caviar 500GB 7200rpm, S300, 16MB SATA (data disks)
BIOS – 1.1 updated to 1.5, default settings (I'm not overclocking)
Windows XP SP2 OEM
I installed the above system last summer and have been having problems ever since. Initially the video signal dropped after booting so I replaced the graphics card. This didn’t work so I replaced the MOBO. All was OK for a while then the system started crashing for no apparent reason but would usually be OK for a while after re-booting. Then it failed to boot into Windows at all. I checked the BIOS and noticed that the Smart Fan setting in the H/W Monitor had disabled itself somehow (I had set it to be enabled with a target temperature of 40OC). I re-enabled the setting and was able to boot into Windows OK. However it still crashes every time from a cold boot (the CPU fan comes on full speed for a few seconds then the computer just shuts down). After a few re-boots it settles down and seems to be fine.
I’m assuming the problem is something to do with CPU temperature but in the BIOS H/W monitor the system and CPU temperatures are never above 30 to 35OC. As the system seems to be perfectly stable once it’s been re-booted a few times it doesn’t seem that the CPU is actually overheating. I’ve tried setting the CPU target temperature higher (say to 60 OC) but still get the same cold boot crash. Note that the MSI Dual Core Centre utility in Windows shows the same CPU and system temperatures as the BIOS monitor (although the GPU temperature is much higher at 60 OC).
Any suggestions for solving this would be much appreciated.

I'm not familiar with your brand of ps. Have you tested the rails while the system is running using a digital voltage meter?

P6N SLI Platinum not booting after CPU change

I just upgraded the CPU in my machine with a P6N SLI Platinum motherboard from a E6700 to an E8500. I first upgraded the BIOS to 1.7 as the MSI page seemed to indicate that was a pre-req for this CPU. The machine was working fine for a day with the new CPU.
I changed the CPU in the machine and when I tried to boot, the lights on the motherboard came on as well as the fan, but no video or sound. In addition none of the diagnostic LEDs on the D Bracket light up. They had been previously working. Neither do the lights on my memory sticks light up.
I tried clearing the CMOS by hitting the switch but nothing. I am now going to try switching back CPUs but I don't have much hope that that is the problem given the diagnostic LEDs don't light. Does anyone have any suggestions as to a fix or is this motherboard fried?
P.S. Do you hit hte CMOS clear switch when the computer is off but the motherboard is charged? Or do you unplug the computer and wait for the internal orange light to go out as well too?

Quote from: Henry on 24-January-10, 11:41:19
What is the QC number (by the cpu socket) is 01, 02, or 03?
See this thread for more:
https://forum-en.msi.com/index.php/topic,123486.msg932471.html#msg932471
Ah. Given I bought my P6N SLI Platinum 3.5 years ago when they first came out I imagine mine is one of the older versions that doesn't support 45nm CPUs by default. Is there a photo somewhere showing where the QC number is located exactly on this MB? It's probably located under my huge CPU heatsink and I'm not going to remove that for a third time just to check.
I really wish the MSI CPU compatibility page mentioned that. It would save me a lot of time. It's not worth my time and effort to dismantle my PC, send them the MB and wait for them to send me back a compatible one.
I verified the BIOS upgrade by looking at the version number at startup and using CPUZ.

P6N Sli Platinum front audio panel and CPU temp voltage issues

Hi All,
I got my P6N Sli Platinum yesterday, build up my computer without any major issues. However I have noticed that my audio front panel does not work. It could not detect my microphone when i plug it into front auido panel, it works fine for the rear auido panel though.
Another issues is I highly doubt the accuracy of CPU temp sensor. Msi 's software monitor reports my CPU temp is around 19-20 degree, I know that's too good to be true even I am using a water cooling system. Btw my cpu is E6600. Anyone else has the similar issues?
The third, I notice my CPU voltage is bouncing between 1.1 to 1.24 in CPU-z. And the multiplier is changing from 6 to 9, frequency is changing from 1.6g to 2.4g. I only see this in CPU-z. Msi 's own software reports CPU running at 2.4g though. Is this cpuz issue or something else?
Finally, any tips to max the overclock potential of this board? I have overclocked to 3.1g but there are some crashes. Going higher the board just won't boot up. I read a review on anandtech.com says 1.22 bios is good for oc. Where can i download that? I only found 1.1 bios on official site.
Any reply will be appreciated.
Cheers

Quote
Another issues is I highly doubt the accuracy of CPU temp sensor. Msi 's software monitor reports my CPU temp is around 19-20 degree, I know that's too good to be true even I am using a water cooling system. Btw my cpu is E6600. Anyone else has the similar issues?
C2D-CPUs have a digital internal sensor to monitor CPU Core temperatures. Have a look at those with Core Temp ( http://www.thecoolest.zerobrains.com/CoreTemp/ ). This Tool reads the temperature data directly from the register of your CPU. There is nothing wrong with the sensor. It is rather the MSI tool that does not read the data it provides correctly.
Quote
The third, I notice my CPU voltage is bouncing between 1.1 to 1.24 in CPU-z. And the multiplier is changing from 6 to 9, frequency is changing from 1.6g to 2.4g. I only see this in CPU-z. Msi 's own software reports CPU running at 2.4g though. Is this cpuz issue or something else?
There is no issue. What CPU-Z allows you to see there is the C1E-feature of your CPU at work. When there is nothing to do your processor will automatically reduce Core Voltages and frequency to save power and keep temperatures down. As soon as the work load increases the multiplier is set back to x9 and core voltages increase dynamically. It is meant to be a good thing.
I have overclocked my system a little and I like that the C1E feature is still working at this speed setting CPU frequency to 2GHz and core voltage to 1.144v when my system is idle.
If you have problems with this feature you can turn it off in BIOS. The option is labeled as "C1E Support" and might be hidden somewhere. You may be able to hit "F4" to unhide it.
The MSI utilities are not the best tools to monitor your system. CPU-Z, Core Temp, Everest, Speedfan, Memset, Rightmark Memory Analyzer for example do a far better job.

MOVED: P6N Sli Platinum - Problem

Similar Messages

Maybe you are looking for