Movies sound stopping and starting

Sony xperia z1Sony carried out a large software update about a week ago,after that none of my movies work properly now, this is what happens.about every 30 seconds the sound stops for approximately 5 seconds, when the sound starts again the movie pauses for approximately 2 seconds, then it happens all again 30 seconds later,this is on all my movies iv deleted movies,reinstalled,deleted cache, and now connected to sony companion and done a fresh install to factory settings, still the same,I need my movies for flying abroad has I'm on holiday in a week,please resolve...... Thanks

Are these your own movies or movies from PS Video as it's now called and do you have PS Video installed
For a successful technology, reality must take precedence over public relations, for Nature cannot be fooled. Richard P. Feynman

Similar Messages

Apple TV problem- Netflix message not availabale at present etc. On Itunes playing a movie the sound stops and starts how can the downloading hurry up. On the computer all OK.

Netflix keeps posting not available- have restarted it as directed but still a problem. Itunes movies dont download fast enough and stop and start. On the Imac computer no problem with sound or viewing.

What is your current connection using speedtest.net
I would check for interference using istumbler
Make sure DNS is set correctly on ATV (settings - general - network - configure DNS - automatic)

Sound stops and starts with x-fi titanium pci e

I am going nuts with this problem and creative support is not much help atm, so I have been troubleshooting myself. Whats going on is my sound stops, starts, and stutters a lot. It is pretty bad when I play music files but it is absolutely horrible when I watch videos like on CNN or YOU TUBE. It is like a old vinyl record skipping, except when this gets off a stutter, it races to where it should be on the time line. Also my creative console does not work right. I cannot use the equalizer, as the custom, rock, pop music select is greyed out and the box is checked to use the equlaizer. It also disappears when I click on a few tabs, like between speakers, bass, equalizer..then its just gone and I have to click the shortcut again to get it back.
What I have done so far is un-install everything, and do a clean boot, then re-install and I have the same problems. Though I downloaded the creative console beta(2.6.49) and it seemed to have fixed my issues with that. But downloading the new drivers (2.7.8) does not fix the stopping and starting.
Any suggestions?
I should mention I use klipsitch speakers..2.1, I don't have surround sound anymore.
Customer service had me run a registry cleaner and use it to uninstall everything creative. I used CCleaner, then used direct links to download drivers...again...(2.7.8) and a creative console(2.6.35)..guess what? It didn't work, same problems, though I downloaded and re-installed the beta for the creative console(2.6.49) and now it works fine. I also did all this under a clean boot..again.

Check if "Play Stereo Mix using Digital Output" is checked in the Console launcher in Settings/Digital IO.

Sound stop and start on DVD

Hi
I make a diaporama on iDVD with music. When I watch it on iDVD, everything is perfect. After burning it, I tried to watch it on my home DVD player. Everything was fine except, at some points, the music stop 2 seconds and start again. It's like we paused the music for two seconds. It makes it few times on the DVD.
What could be the problem??

Q: To export as a Quicktime video from iPhoto, do I need to buy Quicktime pro?
A: No you do not need to buy QT Pro in order to Export from iPhoto as a QT file or movie.
Have you tried this?
Click Here:

TS2972 My downloaded movie keeps stopping and starting

My downloaded movie keeps stopping on my apple TV

Repair your QuickTime.
Control Panel > Programs n Features > highlight QuickTime and click CHANGE then REPAIR.

T530 sound stops and starts

The sound on my T530 will stop working and then if I leave it alone for a while it will start back. It seems to happen after I've used my headphones but I'm not sure. Any ideas?

Hi Hbyrd,
Welcome to Lenovo Community!
Have you checked with updating drivers from Lenovo support site?
Have you checked with different ‘Headphone’, is the same ‘Headphone’ working fine with other system?
Hope this helps.
Best regards,
Hemanth Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Apple tv sound stops and starts

?my apple TV keeps cutting in and out after 15 or 20 seconds it cuts out audio for 1 or 2 seconds and keeps doing this.
Can you help.
roy52

Hi roy52,
I found the following information which may assist you in troubleshooting this issue:
Apple TV: Basic troubleshooting
http://support.apple.com/kb/HT1551
If you can see video but can't hear sound
If Apple TV is connected to a receiver, make sure the receiver is turned on.
Make sure the input setting you've selected on your receiver matches the input you have your audio cables connected to. See the documentation that came with your receiver for more information.
Make sure the volume on your TV or receiver is turned up and isn't muted.
Check whether you can hear sound while playing video only. Also, check whether you can hear audio feedback while clicking through menu options.
If you're connected to the HDMI port on your TV and Apple TV, make sure your TV supports audio through its HDMI port. The HDMI ports on some older TVs support only video.
If you are using HDMI audio, try disconnecting and reconnecting the HDMI cable.
If you're connected to the HDMI port on your TV and Apple TV, make sure your TV is setup to receive audio from HDMI. For some TV's this is automatic, but for others there is a choice between digital and analog (for HDMI audio, choose digital). Read more about HDMI audio.
Try the other audio outputs on Apple TV to see if they work.
If possible, try using different audio cables.
Cheers!
Matt M.

Firefox4 on ubuntu, after awhile when I click on bookmarks and then move the cursor down to a bookmark, the list of bookmarks disappears. A stop and start of firefox4 fixes the problem but what is the long term fix?

I upgraded to 4 and I noticed that after 4 has been up for an hour or so I click on the bookmarks. I see my list of bookmarks below but when I move the cursor down to select one, the list disappears.
The only way I have found to fix this is to stop and start 4. I can then move the cursor down to select a bookmark. This problem has not occurred in previous versions.
ps.. no '''''delicious''''' installed

No, I see the three areas at the bottom of the Bookmark area that you refer to, but that also highlights an issue. When I want to save a story to my Reading List and click on Share then "Add to Reading List" then go back to look at what is stored in the Reading List, my recently-saved item is not there.
I looked thru the History tab and the Reading List tab and have been in the Bookmark tab. But even when I Save a Bookmark, that newly-saved Bookmark does not show up in the Bookmark area.
But then again, the next day (and actually just in the last half-hour) all of the functionality came back. When I look at the Bookmarks, suddenly, again, all of the Bookmarks that are on my Safari browser on my iMac are now there, and I can now Save a Bookmark.
It keeps coming in and out and that is what is driving me a little nuts.
Thanks.

I have a Macbook pro mid 2011 and just bought the Apple TV. While watching program or movie from any of the apps such as Watch ABC, the program keeps stopping and starting constantly.

I have a Macbook pro mid 2011 and just bought the Apple TV. While watching program or movie from any of the apps such as Watch ABC, the program keeps stopping and starting constantly.

That would indicate a network issue.
Reboot ATV and router
Make sure DNS is set to auto
Ensure router is up to date, if on wifi try ethernet
Go to istumbler.net to get a report of the network, look for signal strength and noise

My lap top is extremly slow. It studders. It kind of sounds like there is a fan inside and it constantly stopping and starting. And, it takes a really long time for it too start up. Whats wrong with it?

My lap top is extremly slow. It studders. It kind of sounds like there is a fan inside and it constantly stopping and starting. And, it takes a really long time for it too start up. Whats wrong with it?

Do you have current backups?
Those symptoms could indicate a failing Hard drive. If it dies, all your documents go with it unless you have Backups.
I have had very good luck with physical and battery problem diagnosis at the Genius Bar. Those guys put their hands (and their ears) to these machines, all day every day, and they know immediately what all those sounds mean.
Your appointment for an evaluation is FREE, in warranty or out.

Sound randomly stops and starts

Hello,
Over 2 days, as I watch Netflix, or listen to music on other apps, my sound randomly stops and starts. I have no control of it. I do not have to touch my ipod when this happens, it does this on its own. On for 20 min, off for 5 min, on for 5, off for 2, on for 1 min, off for 15 min. It ossolates randomly through time.
I hard reboot, but this works or does not work (for a while). Any ideas?

Hello,
Over 2 days, as I watch Netflix, or listen to music on other apps, my sound randomly stops and starts. I have no control of it. I do not have to touch my ipod when this happens, it does this on its own. On for 20 min, off for 5 min, on for 5, off for 2, on for 1 min, off for 15 min. It ossolates randomly through time.
I hard reboot, but this works or does not work (for a while). Any ideas?

HT1338 just bought a new I-Mac. At start up several updates were needed. The I-movie one stopped and shows an ERROR HAS Occurred. Howevr it does not allow me to update it again. In my purchases it shows as Installed with Error. What should I do?

just bought a new I-Mac. At start up several updates were needed. The I-movie one stopped and shows an ERROR HAS Occurred. Howevr it does not allow me to update it again. In my purchases it shows as Installed with Error. What should I do?

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Select "/var/log/install.log" from the file list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar. Then select the messages from the last installation or update attempt, starting from the time when you initiated it. If you're not sure when that was, start over and note the time. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V).
If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting.

How to stop and start MDBs to listen for JMS messages

Hello! This might be more of an architecture question rather than a technical questing, but I post it here, in the lack of a better place...
For several years I have been using Webster and Webster MQ to send messages back and forth to clients. The architecture for the middleware platform has been designed around the functionality of ListenerPorts. Listenerports is a Webster functionality that let you "stop" and start to listen to JMS messages for a given MDB either by admin console, or by JMX.
The arhitecture we used was something like this :
1.Client sends a persistent message to a queue. (order)
2. An MDB pics up the order message, calls a SessionBean that "fronts" the IIOP back end system.
This is quite "out of the box" architecture, but we used the Listenerports to solve a stability problem for our back end system.
The backEnd system was quite unstable, so the EJB threw an exception (typically because of timeout or connection refused) back to the MDB.
The Listenerport was "defined" to handle 3 errors before stopping, so the MDB resent the message twice before the listenerport automatically stopped. The nice thing about this feature was that the client could continue to send orders, and was not bothered when the back end system was down.
When the backEnd system was up and running, we could start the listenerport and it was all back to normal state. We even had a start script that checked the state of the listenerport every 30 minute, and started it automatically if it was stopped, making the admin task of starting the MDB unnecessary..
Now.. Why am I telling this story..
I would like to know how this could be done using "clean" J2EE technologies..That is..Not using any technology that is not portable..
I`m playing with glassfish at home, and it struck me that there is nothing in the J2EE spec that defines the functionality described above ? Am i missing something ?
I Do not want to stop My application because the back end system is down? That is the only way (i know of) that i can "stop" to listen for messages..
I can put all the messages on an error queue when the backbend system is down, but that would lead to more code just to handle the error messages. Maybe the easiest way to solve this is to "move" (programmatically) all messages from the error queue over to the "standard" queue every XX minute, but somehow that sounds "wrong"
Can anyone give me some advice to how this problem situation should be solved ? I`m interested in the solution both from an architectural perspective and from a more technical perspective..
Best regards
Hans-Jacob Melby

Breakpoints, whether normal or conditional, are just meant for debugging of your code. I had the sense from your question that the pausing you want to do is a part of normal operation of your code. I would NOT recommend using a breakpoint for that situation. It would bring up the block diagram showing the breakpoint when it occurs. A user besides the programmer would not know what to do in that case.
Yes, both the inner and outer loops would have shift registers.
Putting a case structure with a small while loop inside the "Pausing Case" is doable. It just depends on what you are doing or waiting for while the program operation is "paused".

Downloaded a movie from iTunes to my iPad. 2 minutes into the movie it stopped and My Videos is stuck in black screen mode. So basically rented a movie and never watched it.

Downloaded a movie from iTunes to my iPad. 2 minutes into the movie it stopped and My Videos is stuck in black screen mode. So basically rented a movie and never watched it.

The EXACT same thing happened to me last night! Rented a movie; it had barely started and then froze. When I touch the video app icon, all I get is a blank, dimly lit screen. None of the other videos I own will display either. Was your problem ever resolved?

Videos stop and start

I've got a fast computer w/plenty of ram. I can watch videos from all other sources perfectly smooth, including Quicktime HD movie trailers.
When I try to watch a video in iTunes it slows my computer down so much that besides the videos stopping and starting, my mouse won't even move smoothly.
It worked fine until a couple of weeks ago.

Phyllis-
One reason is that your internet connection is not fast enough to keep up with the video. You may find that when it gets to the end of the video and has fully downloaded, it will replay without stopping.
Fred

Movies sound stopping and starting

Similar Messages

Maybe you are looking for