Moving home - when does current address get discon...

I am moving home so i will be doing the moving home thing to move our connection over.
It says our current address will be disconnected but it doesn't state when? It also asks time at our address for a new credit check, what address it doesn't state either?

It will be disconnected on the date that you want it disconnected and the address will be your present address not your new address.

Similar Messages

When does an AP gets to Air-Monitor mode?

Q: When does an AP gets to Air-Monitor mode?
A: In a Mobility-controller AP deployment there are just 3 conditions that an AP can go into an Air-Monitor(AM) Mode:
1. If the am-mode is configured in the "rf dot11a-radio-profile" or "rf dot11g-radio-profile"
To see if it is configured in the radio profile please use this filter in the show running-config command
Example:
(Aruba) #show running-config | begin "rf dot11a-radio-profile"
Building Configuration...
rf dot11a-radio-profile "default"
mode am-mode ------------------------------------------------------------- Indicates that the Airmonitor is Enabled
2. If Mode Aware ARM is turned on in the ARM profile then th ap turns to AM mode when it sees excess power from the neighbor AP
To see if mode aware arm is enabled in the arm profile please use this filter in the show running-config command
(Aruba) #show running-config | begin "rf arm-profile"
Building Configuration...
rf arm-profile "default"
mode-aware ------------------------------------------------- Indicates that the mode aware arm is enabled
3. During the Regulatory mismatch or un-supported
a. When there is no channel available for the AP’s operation for the country defined on the controller.
Use the following command to verify the allowed channels for an AP
(Aruba-7240) #show ap allowed-channels ap-name <name-of-ap>
b. When AP’s has a different country with the controller’s Country.
Compare the country defined on the controller "(Aruba) #show country" to the country defined in the "(Aruba) #show ap regulatory-domain-profile <profile-name>". The ap regulatory-domain-profile will be mapped in the ap-group to which the ap is provisioned to.

Hi Marc,
I have a shop system comprised of two web applications where one is for
maintaining the shop and the other for using the shop. When I do changes
to the shop from the one webapp they do not show up in the second, unless
I call refresh. Also, I have to switch off the cache, it seems and do a
flush on the changed objects. There are some questions now:
a) when I call refresh, is the complete state reread regardless whether
there have been changes or not or does it know, when the state has not
changed in the DB ? it is a performance question, I guess.
b) can I use transactional reads to do the refresh automatically ?
c) I noticed that refresh does not do a deep refresh of all the objects
referenced by the one to be refreshed. Is there a way to do this or do I
have to go thru all the objects ?
I asked some questions some time ago in another thread, which might refer
to. I am sorry, if I am not clear enough.
Best regards
Wolfgang
Marc Prud'hommeaux wrote:
Wolfgang-
I take the question to mean that you are wondering how you can refresh
the state of a persistent instance to reflect changes in the data store.
If that is the case, then you can just call
PersistenceManager.refresh(ob) on the object, and the newer values will
be obtained.
If that doesn't help, can you clarify the question a little?
In article <cj7ris$mhr$[email protected]>, Wolfgang Kundrus wrote:
Do I have to use transactional reads for an object to get the changes done
by another web application ?
Thanks
Wolfgang
Marc Prud'hommeaux
SolarMetric Inc.

When does the horizontalScrollBar get created on a List?

When does the horizontalScrollBar get created on a List?
The scroller is created, but the scrollbar isn't created yet and I get an error:
I have a spark List:
<s:List id="list" creationComplete="creationCompleteHandler(event)">
        <s:layout>
            <s:HorizontalLayout />
        </s:layout>
</s:List>
private function creationCompleteHandler(event:FlexEvent):void {
     (event.currentTarget as List).scroller.addEventListener( FlexEvent.UPDATE_COMPLETE, onScrollerComplete );
// these don't trigger anything!
//    (event.currentTarget as List).scroller.addEventListener(FlexEvent.CREATION_COMPLETE , onScrollerComplete );
//    (event.currentTarget as List).scroller.addEventListener(Event.ADDED_TO_STAGE , onScrollerComplete );
private function onScrollerComplete(event:Event):void {
     // horizontalScrollBar still null at this point - how can I use it?
     // I want to set the style, but it's not created yet!
     // event.currentTarget.scroller.horizontalScrollBar.setStyle("repeatInterval", 600);

I just realized that
this.setIconImage(new ImageIcon("image.jpg").getImage())
did not create the icon for my saved files.
So what did create it? I did not program it!
However, I happen to have an icon file Ananya.ico where I have my java project. I use if for my installation file. Did Java use this icon?
Please help! Thanks!

When doing catalog backup get message " your system is low on disk space, and elements organizer can

When doing catalog backup get message " your system is low on disk space, and elements organizer cannot perform the operation. If create a catalog with 20 pictures backup works OK. backing up to a 1TB external drive. Have 16705 pictures in catalog. Total disk space for pictures is 192 MB. Why am I getting message?

kdrozzen a écrit:
Total disk space for pictures is 192 MB.
Do you really mean MB (megabytes) or GB (gigabytes) ?
Even if its GB, the free space may be enough, depending on your files size, especially with videos or raw files.
When you start the backup process, it first shows you the total size of the catalog.

When does the JSP get regenerated!!

Hi,
Can anyone please tell me When does the JSP get regenerated!!
Thanks in advance
SP
[att1.html]

Answered on interest.jsp
(please don't cross post)
mbg
=============================================================
"SP" <[email protected]> wrote in message
news:[email protected]..
Hi,
Can anyone please tell me When does the JSP get regenerated!!
Thanks in advance
SP

When does Mac Mini get i7 processor?

I really like the Mac Mini design. but when does this product line get updated with i7 processor?

sharpxia wrote:
but when does this product line get updated with i7 processor?
when Apple deems the time is ripe.

Moving Home option does not work

I try to use option "Moving Home" but after i enter all details and click continue page reload and stop in same place. I enter details few times, change date, continue and still nothing.

Call BT 0800 100 400 and they will arrange your home move.

When does a bean get initialised?

Hi,
I am a bit confused at the moment, and the more I think about it, the more confused I get! Here is the scenario....
Some details - it is a JSF application using JSPs and JSF Components. I am using JDeveloper 1.3.2 and Oracle 10g DB.
I have a page (login.jsp) that calls a method in the LoginBean when the user clicks the Login button. This then goes off to the DB and retrieves the user's data (if he/she exists). If successful, the user is navigated to the welcome page. At this point I wish to display the user's details (EmployeeBean) - which are stored in another table, and so will require a query to the find the user's details based on their user_id (retrieved when logging in).
My question is - when/how can I populate the Employee bean. Do I need to explicitly create the Employee bean (with new EmployeeBean()) or does the faces-config.xml sort this out. How can I 'tell' the application that when the welcome.jsp page is loaded I want/want to have populate(d) the EmployeeBean with the relevent details.
If this requires further info, please tell me and I'll add to it!
Thank you.

Hi,
You can use a session bean (the LoginBean or an other) that retrieves an EmployeeBean entity bean from the database if the id is given. You should call this method from the welcome page and display the data of the retrieved entity bean.
Regards,
Kati

When does an object gets refreshed, if its state has changed in the cache?

Do I have to use transactional reads for an object to get the changes done
by another web application ?
Thanks
Wolfgang

Hi Marc,
I have a shop system comprised of two web applications where one is for
maintaining the shop and the other for using the shop. When I do changes
to the shop from the one webapp they do not show up in the second, unless
I call refresh. Also, I have to switch off the cache, it seems and do a
flush on the changed objects. There are some questions now:
a) when I call refresh, is the complete state reread regardless whether
there have been changes or not or does it know, when the state has not
changed in the DB ? it is a performance question, I guess.
b) can I use transactional reads to do the refresh automatically ?
c) I noticed that refresh does not do a deep refresh of all the objects
referenced by the one to be refreshed. Is there a way to do this or do I
have to go thru all the objects ?
I asked some questions some time ago in another thread, which might refer
to. I am sorry, if I am not clear enough.
Best regards
Wolfgang
Marc Prud'hommeaux wrote:
Wolfgang-
I take the question to mean that you are wondering how you can refresh
the state of a persistent instance to reflect changes in the data store.
If that is the case, then you can just call
PersistenceManager.refresh(ob) on the object, and the newer values will
be obtained.
If that doesn't help, can you clarify the question a little?
In article <cj7ris$mhr$[email protected]>, Wolfgang Kundrus wrote:
Do I have to use transactional reads for an object to get the changes done
by another web application ?
Thanks
Wolfgang
Marc Prud'hommeaux
SolarMetric Inc.

Outputting an error message in MV50AFZ1 when doing a VL01N - getting update

Hello. I am getting an "update terminate" message due to using a MESSAGE statement in user-exit USEREXIT_SAVE_DOCUMENT_PREPARE . We need to be able to stop a delivery from getting created and alert the user under certain circumstances (if a field is not filled in on a separate screen). I have seen under Note 415716 that we cannot use the MESSAGE statement. Is there any way to stop a delivery from being created while informing the user that they have not filled out the required field? (This field is on another tab that they may not see when creating into the delivery). I have tried various uses of the MESSAGE statment, tried perform message_handling, etc., but still no luck. Thanks for any help!
Regards,
Vince

Hi Vince,
I am not too sure but could you please check below subroutine of SAPMV50A-
        PERFORM message_handling USING
                                       <item#>
                                       <number>
                                       <type>
                                       <id>
                                       <msgv1>
                                       <msgv2>
                                       <msgv3>
                                       <msgv4>.
Thanks
Mohit

When does new user get new minutes from ATT

I bought the iPhone a few weeks ago... on Feb 8. It is March 1st today. Shouldn't I be getting a fresh set of 450 minuets? I checked my minutes (clicked the "show my minutes" button in Settings-->Phone--> ATT Services) and it shows 332... which is about right (I don't use it that much obviously.)
When do I get my new minutes? Not the first of the month?
Thanks,
Al1776

If you don't yet have an online account with AT&T you can set one up very easily on their website in a couple minutes. Just put in your mobile number and it will prompt you to complete some information and then your good to go. Since you signed up on the 8th your billing cycle will fall some where around that date each month. Your first month will be pro-rated for partial service you receive, as well as the activation fee, and the entire bill for the next full month.
I signed up on the 5th of a month and my cycle is on the 5th of each month. From AT&T you can also pay your bill online, the only thing you can't do is manage your account features for the iphone plan. You have to have AT&T do that for you, they tell me you can do from itunes but I have not looked very hard to see how to do it.

When does your Address Book picture show up to correspondents?

In the Accounts pane of System Preferences is either a picture of us, taken when we initiated the computer or a stock picture, butterfly etc. which is also in the "My Card" of our Address Book.
When using Mail, when do these show up to our correspondents and can we choose to include the picture or not?
Chris

When using Mail, when do these show up to our correspondents and can we choose to include the picture or not?
They do not - they are a local display only
LN

Where and when does requisition id gets created when creating from MSS?

My requirement is to have a custom logic on how to assign recruiters to a new requisition which is beeing created from MSS. Once i fill out the form and send the form i get a ref nr for process. What i need is the requisition id as i want to create those recruiters in table HRP5131.
So my question is: when and where is the requisition id beeing created?
Any help will be appreciated.
Thanks

Hi Nahman,
Check the following nodes
SPRO--> Integration with other my sap.com components --> Business packages / Functional packages --> MSS (my SAP ERP) --> recruitement --> Define attributes for request scenario
Select the recruiter logic type. You have an option to use custom logic also using a BADI. other than this there are 3 more options provided by standard sap.
Hope this info helps. Let me know if u require further help on this
Thanks
G Raj

When does the configuration get locked for changes in sales order?

Hi Experts,
I will really appreciate your help me in resolving this issue.
Our client had sales order having BOM item with several sub items.
Here we found that the user was not able to make changes to the Characterstic Value of one of the variant.
The issue was the place where we change the characterstic in sales order was greyed out, it was probably locked. Now even if they were unfrezing and trying to change the characteristic value the system did not allowed means greyed out.
Can you please help me in understanding when do system locks the variants for a material in sales order, in what stage?
Like maybe after the delivery document is created or PGI or some things else.
since i see that the user here did delivered one of the item in the BOM subitem.
Thanks
Kaushik
<Text removed by Moderator, please don't share your personal details on SCN post>
Message was edited by: Jyoti Prakash

Yes the characterstics were maintained for the main item.
and the delivered item was a subitem for this main item.
So characterstic were maintained for Item 10(Main item) but delivery was done for some of its sub item was item 100 / 120
Also can i know where is this setting or configuration where we configure this to block the configuration if any of the subitem is delivered.
Thanks
Kaushik.

When does the uk get iTunes Radio?

Does the UK have a date for iTunes Radio?

Music industry still trying to carve the world up into discrete territories despite the fact that the internet is global. If you want iTunes Radio now just create a US ID. It's simple and works.

Moving home - when does current address get discon...

Similar Messages

Maybe you are looking for