Moving raid 0 from SATA 3, 4 to SATA 1, 2

Does anyone know if my array will be intact if I switch the SATA ports I am using. Currently using the ones down by Bios reset jumper, and would like to use the ones above the AGP slot for better overclocking.

Not so good news. I did not have the raid 3 and 4 enabled in the bios. I enabled them and rebooted with the array still on 1 and 2. Windows found the new controller and I shut down. Placed the array on 3 and 4 and rebooted. Up came windows and all was fine. Now on 3 and 4. Overclocked a little bit and system froze up. I shut down and was going to try again using clock gen, but the OS would no longer load. I tried it on both sata ports and no go. I finally had to delete the raid array and start from scratch. Kinda pisses me off. I have never had this issue with other boards SATA ports. I understand the issues with this board and know that by being an early adopter these kinds of issues will crop up....but damm it. I have put enough time into this setup already and now I have to reinstall everything once more. Time to ghost the array. I am not going through this again. I hope that the next bios update clears some of this crap up.

Similar Messages

MOVED: Raid problems after switch from K9N2-Platinum to 790FX-GD70 mobo

This topic has been moved to Linux/Unix.
https://forum-en.msi.com/index.php?topic=130049.0

Hi BOSSKILLER
Thanks for your quick response.
Quote from: BOSSKILLER on 12-August-08, 00:14:44
Well, leave the 80GB only and install XP over it.
Then connect other two HDD's and enable RAID for them.
Unfortunately this didn't help. As soon as I installed the Windows nVidia RAID SW it prompted med that it had registered the 80 GB disk as a new disk that wasn't a member of any RAID. This happened everytime Windows XP was started.
The trick was to add the 80 GB disk as a Spanned disk using the nVidia RAID BIOS setup utility. Install Windows XP (again) and the Windows nVidia RAID SW and setup RAID 1 on the other two sata disk.
I don't think this is a great setup but it works. I hope that MSI will fix this issue in a later BIOS upgrade. It would be nice if the enabled/disabled for sata RAID setting actually worked.

MOVED: K8N Neo2 question about overclocking and sata ports 1 & 2

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=130785.0

Quote from: SteveH647 on 24-September-09, 04:39:34
But is it the HDD itself that fails at the higher frequency? Or is it the HDD controller on the motherboard that fails? What about DVD drives? And what if the HDD is SATA 300 instead of SATA 150?
Quote
But is it the HDD itself that fails at the higher frequency?
Yes.
Quote
Or is it the HDD controller on the motherboard that fails?
No
Quote
What about DVD drives?
Can't tell you, haven't maked such experiments.
Quote
And what if the HDD is SATA 300 instead of SATA 150?
It will not change anything.

TS1347 Dear apple, The governments of Saudi Arabia has changed its weekend from THR&FRI to FRI&SAT, Therefore the start day of the week became SUN. unfortunately all Iphone user could not adjust this change on their I phones . So will you please facilita

Dear apple,
The governments of Saudi Arabia has changed its weekend from THR&FRI to FRI&SAT,
Therefore the start day of the week became SUN. unfortunately all Iphone user could not adjust this change on their I phones .
So will you please facilitate us on this matter.
Regards

Give apple feedback regarding this.
For a temporary fix, change your region? Get a 3rd party Calendar app that fits your needs?
I assume your current region is set in the photo?
If so, pick a region that has a start day of Sunday. (either historically or known for the present)
Note, with changing your region, it will change the default phone number prefix/country code for new contacts and addresses. (calling and SMS is not affected)

Problems moving files from old start-up following upgrade prep :(

So I thought I would do a clean Leopard install ahead of moving up to 10.6...
Bought a new 1TB SATA drive, 10.5 installed and updated, all apps installed, no problems. I did create a new user account rather than migrating - sounds silly but I wanted a completely clean slate as I've been upgrading this system and carrying the user account forward forever...
Now I am trying to copy my DTP files across from the previous boot drive and I don't seem to have permissions over them, even though 'Get info' says I do.
E.g. moving them from folder to folder does a copy rather than a move, and more often than not needs a password.
Any got suggestions for the best practice approach to move files between SATAs, when the two drives have different accounts, etc? I am wary of the ACLs, changing permissions and screwing things up...
Thanks v much

If you can you connect both external drives to the computer at the same time, it would be easier to use the "Consolidate Library" utility in iTunes to move (actually copy) your media to the new drive.
1- Open iTunes preferences and select the Advanced tab. Change the location of your iTunes music folder to a location on your new drive. Also select the options "Keep iTunes music folder organized" and "Copy files to iTunes music folder when adding to library". Close the preferences dialog.
2- On the iTunes menu, select Advanced/Consolidate Library. This will gather all your media and copy it to the new location (the folder you designated in step 1).
3- After the consolidation is complete, verify that your music still plays, and check "Get Info" on some items to verify that iTunes is looking at the new location.
4- Optional. Delete the original files on your external drive. Do this only if you are certain that everything copied over to the new drive.
5- Optional. Close iTunes and locate your "iTunes Library.itl" file. This is typically in your iTunes folder, which may be on your computer's drive and not the external drive. Move this file to somewhere on your new external drive. Next, hold the Shift key as you launch iTunes and you'll be prompted to "Create Library" or "Choose Library". Select "Choose Library" and navigate to where you put the "iTunes Library.itl" file. This is a one-time step that tells iTunes where to boot the library from.

Sata I compatible with Sata II

Is sata I compatible with sata II?
I wonder if my sata I disks will work on a sata II mobo?

Quote from: Maesus on 24-October-05, 00:43:16
Mr. Bister, I would phrase it as SATA I drive can work without any issue with SATA II controller. I don't see any failure yet. Most issue came f rom putting a SATA II drive with a SATA 1 controller.
Can you confirm the issues please? I am soon to replace my SATA drive with SATA II in a RAID config.

Does the HP Envy 17t line have 2 SATA bays or 1 SATA and mSATA?

Does the Envy 17t line have 2 drive bays? If so, is it 2 SATA bays or 1 SATA and 1 mSATA? Also, on the hardware selection screen:
If I choose that option, will you guys at HP install Windows on the SSD, instead of on the hard drive? I found 256GB SSDS that are a lot cheaper than $295, but I searched around and found that HP apparently puts a restriction on the BIOS that prevents you from booting from an internal drive that you added.
EDIT: Perhaps I could also get the 256GB SSD and add my own hard drive. But I still need to know if it has 2 SATA or 1 SATA and 1 mSATA.
This question was solved.
View Solution.

1337iscool wrote:
banhien wrote:
Hi,
You have not read the manual, I meneioned page numbers for you too. It has one M.2 slot/bay and 1 normal 2.5" bay. I also mentioned: "replacing HDD on new machines now is not as easy as before and in some cases, would void warranty too"
Regards.
OK, so....
1) why do you expect me to read the whole manual?
2) I am aware that replacing a hard drive will void warranty. I am not planning to replace a hard drive but rather add a hard drive in the second drive bay.
What I need to know is what hard drive ports are there, mSATA, 2 SATAs, etc. I have no idea what they mean when they say "support M.2 SATA". Does that mean it supports M.2 SATA or is it an M.2 SATA port??
EDIT: apparently M.2 SATA is only for SSDs, since I can't find any M.2 SATA hard drives.
So what I know now is that there's 1 M.2 bay for an SSD, but I don't know what type of port the second drive bay has.
Hi,
You did not read my reply too: I did not tell you to read the whole manual, I read it for you and clearly noted : " Please also check the following manual (page #2 and page #66) " The manual also show you port and type of the SSD 22 something, I will let you to find out.
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Moving Favorites from PC to Mac

Hello,
I'm moving favorites from IE 7 on Windows XP to Mac Leopard. Do I just move the files over and import or is there something specific regarding conversions I need to complete? Thanks.

Hi theBigD23,
Save your Favorites in IE 7 to the desktop (or wherever you want). Use a flash drive, email the file to yourself, or any method at your disposal to get that file over to the Mac.
In Safari, choose File > Import Bookmarks. Navigate to the bookmark file from the PC and click Import.

Moving Songs From PC to MAC

i have a PC (windows xp) that was my old home computer.
Just yesterday i changed my old computer to the newest iMac (21.5 inch) and want to use it as my iTunes home. Here are some issues i'm having:
1: i need help moving files from a pc to mac KEEPING playlist info, play count info, date added info, etc.
2: when i plug in my iPhone to the new Mac iTunes, all the songs on my iPhone are greyed out and can't be played.
3: i've tried homesharing but apple said it isn't meant to save playlists info.
4: (only at least half of my songs are purchased, the rest are from CD's so i can't do the Transfer purchasing thing)
HELP :O

Hello,
Go here: http://www.myfirstmac.com/index.php/mac/articles/how-do-i-move-my-itunes-library -from-pc-to-mac-and-keep-my-settings-intact
More help here: http://support.apple.com/kb/HT1449
Carolyn

HT4889 moving files from pc to mac book

Hi have down loaded to set up moving files from pc to mac book pro but keep getting an error message on pc saying error occurred whilst preparing your info for transfer ! i am running visa on pc any help pls thanks

Look at these links.
*How to use your iPod to move your music to a new computer*
http://docs.info.apple.com/article.html?artnum=300173
http://www.ilounge.com/index.php/articles/comments/copying-music-from-ipod-to-co mputer/
 Cheers, Tom

Why does the new operating system not delete the moved files from their original location - it seems like an enormous waste of space, time and effort to clean up every file once you've moved it

Why does the new operating system not delete the moved files from their original locations - it seems like an enormous waste of space, time and effort to clean up every file once you've moved it - also, when transferring large amounts of files it becomes a very large problem remembering which files were transferred and which not.

You're going to need to be more specific, as I'm not quite sure I understand what you're talking about.
If you're referring to copying from an external hard drive or flash drive, and you want to actually move files rather than copy them, you can hold down the option key to force it to do a "move" rather than a "copy." This is not new behavior, though... the Mac OS has worked this way as long as I can recall (and I've been using it since 1984).
If you're having a problem with trying to move files from one place to another on a single drive causing them to be copied instead, that is likely because of some permissions issue preventing you from actually being able to move them.

HT5621 I have moved permanently from the US to live in the UK. when I try to download a UK app I am often told that I cannot use a UK Apple sstore, only a US store. I need to access various UK stores how can I deal with this?

I have moved permanently from the US to live in the UK. when I try to download a UK app I am often told that I cannot use a UK Apple sstore, only a US store. I need to access various UK stores how can I deal with this?

Try here
http://support.apple.com/kb/HT1311
when you have UK Cards etc best to change as well

How can I script moving paths from one file to another?

Hello. I have 1 image with various color correction layers. The other is the exact same size but only contains paths. How can I script moving paths from one file to another? Thanks, in advance, for any help you can offer. Thanks!

Thanks! This one actually worked for me. Thanks for your help.
http://forums.adobe.com/message/3305389#3305389

How can I preserve the date and time of photos when moving them from iPhone to iPhoto and then to other folders on my computer?

In the past I’ve had no problem moving photos from my iPhone 4 into various folders on my computer while retaining their original date and time. I would import into iPhoto, then drag the photos from iPhoto into other folders via the Finder or Adobe Bridge (which is my principal image organizer). The original date and time of the photo would always travel with the jpeg into iPhoto and then into other folders. However, sometime during a recent session transferring photos in this way, the dates of the photos started to change at the point when I copied them out of iPhoto. Within iPhoto itself, the various original dates of the photos are retained. But in Finder and Bridge, copies of those same photos all carry the same (worthless) date: the date and time that they were imported from my iPhone. I can’t figure out what would have changed on my Mac to make it start re-dating my photos. I was happily dragging and dropping photos, and suddently I started to lose the original dates. Did I inadvertently change some settings? (I am running OS 10.6.8 and using iPhoto 8.)

(I use iPhoto only to import from my iPhone; I organize all my images, including thousands of RAW files, in folders on a big external drive.)
Why are you using iPhoto at all? use image capture or drag and drop the photos
The problem is that the files I am copying are getting stripped of the EXIF metadata
eliminating iPhoto from your work flow will eliminate one oppertunity to have this happen For photos in iPhoto it is best to export them rather than drag an drop them - this assures your EXIF and IPTC data is correct and uptodate
Why would I be able, over many years, to retain EXIF metadata in photos imported from an iPhone--then one day find that the same workflow strips such photos of EXIF data?
Because exporting is the supported way to "export" photos - I never drag and drop photos out of iPhoto and I never use thrid party programs on the photos in the iPhoto library - try exporting as suggested above and see if that is the solution
LN

Process of moving TR from Quality to Production

Dear Experts,
we are in a process of moving TR from Quality to Production. While moving we faced transport incositencies like some old requests have been overwritten into the new one and dependant objects were failed during import in PRD. Now production rehearsal client is kind of messed up. what is the right procedure to transport the requests from Quality to Production. (actually we transferred the TR individually based on the list send by the respectivr module owners). Please help me to findout the solution for this issue.
regards,
Yasin.

Hi,
This situation comes every now & then when you don't have any client strategy define in your landscape I'm not blaming you but for your Project Manager and then rest of the team adopt SAP standard practice if you really want things to go well act NOW..!! here is the basic to start:
Ex,
DEV ::
100 => Golden Client
200 => Customizing Client
300 => Test Client
Things to check before importing request in QAS :
1) Always get the request in sequence format ask the owner of the request for the sequence to avoid dependency issues
2) Technical Specification doc - this doc will be prepare by Functional / Developer on what changes are included in TR
QAS::
400 => Quality Client
Things to check before importing request in PRD :
1) User acceptance doc i.e UAT - client / customer will check the functionality if it's on then move this to PRD
2) Get the request in sequence format
3) Approval for production transport
PRD::
500 => Production Client
Thanks,
Saleem

Issue in moving files from data fodler to processed folder in background

Hi All,
I am facing one issue in moving files from data fodler to processed folder in case of background execution.
When i am executing the file in the foreground, i can move the file from Data folder to processed folder. I am using SXPG_COMMAND_EXECUTE FM to move the file from data folder to processed folder. I can see the file in processed folder once the program is executed.
But in case of executing the same program in background, it is giving me the error "Failed to move the file to processed folder" in the spool of SM37 and i can see the file still laying in data folder.
I tried to check other programs which acesses the same folder as the above program, whether they are able to move. They are able to move the file to processed fodler successfully both in foreground and background mode.
Please help me in resolving this issue.
Thanks,
Deepa

Hi Sanu,
Please use teh following code to move the file from source to target folder.
This is a code showing how to create and use COPY command of UNIX in ABAP
PARAMETERS:
Input file path
p_input TYPE localfile,
Processed file path
p_proc TYPE localfile.
Declare the Types to file data
TYPES: BEGIN OF L_X_OUTPUT,
sys(200), " Please note, there are asterisk before and after sys (i.e.sys)
END OF L_X_OUTPUT.
* Internal table to store file data
DATA l_i_output TYPE STANDARD TABLE OF l_x_output WITH HEADER LINE.
* Variable for the UNIX command
DATA: l_v_unix_comm(255) TYPE c.
Copy command of UNIX
CONCATENATE 'mv' p_input p_proc
INTO l_v_unix_comm SEPARATED BY space.
For example the Copy command is stored as below
cp u2018/data/interfaces/input/input_fileu2019 u2018/data/interfaces/processed/processed_fileu2019
Examples of UNIX Command *u2022 mv filename1 filename2 --- moves a file (i.e. gives it a different name, or moves it into a *different directory (see below) *u2022 cp filename1 filename2 --- copies a file
Execute the UNIX Copy command.
This command will copy the file from input file path to the processed file path
CALL 'SYSTEM' ID 'COMMAND' FIELD l_v_unix_comm
ID 'TAB'
FIELD l_i_output-sys.
IF sy-subrc eq 0.
write: 'File is copied successfully using UNIX command in ABAP'.
ENDIF.

Moving raid 0 from SATA 3, 4 to SATA 1, 2

Similar Messages

Maybe you are looking for