Moving router connections

Presently have router connections in my basement. How hard is it to move connections to first floor?

For connectons, are you talking about something like a homerun? This is something where Verizon will install a splitter at your NID/enterance point that will filter out the DSL for the rest of your home. The DSL modem will be given it's own dedicated line.
If you don't have one of these, moving the router should be as simple as taking the modem/router upstairs and plugging it into a telephone line and power. If it syncs and your speeds are correct, it's probably good to go.
If you do need to change around any of the wiring, things depend on how your home is wired to begin with.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Similar Messages

Moving router connection point.

Yesterday the BT engineer came round and installed Infinity in the house - everything works fine.
The problem is that connection point that I requested is only a temporary point - at somepoint I want to rig up a home network and put ethernet sockets in some rooms.
The original master socket was at Location A.
The engineer setup the open reach infinity socket at Location B.
The socket at Location A looks like this one:
http://helpforum.sky.com/t5/image/serverpage/image-id/635i42831032043407CB/image-size/original?v=mpb...
The socket now at Location B looks like this one:
http://phil.lavin.me.uk/wp-content/uploads/2012/02/fttc-faceplate.jpg
Originally the socket at Location B was a plain old phone extension socket.
My question is; how can I go about moving the modem from Location B to Location A? Is it just a case of procuring another faceplate and fitting it at Location A? Or is Location B now the master socket and an engineer will be required to make Location B the master socket?
BTW; the engineer told me that it is copper running into the house not fibre optic cable.
Thanks,
Ben.
Solved!
Go to Solution.

Yes socket B is now the master socket.
The only person/people that can move the master socket is Openreach or one of their appointed contractors.
If you want / need the modem at socket A you can install your own data cable.
Method A High quality RJ11 to RJ11 cable. The maximum length being 30 meters. This cable should be as short as possible as it directly affects overall connection speed.
Method B using the centre pairs of wires from the cable in method A you can connect on to the back of the RJ11 socket inside the master socket. Others please comment - Are you allowed to do this yourself? I know Openreach normally do it this way.
Keeping the modem at Socket B and the router / HomeHub at socket A
Method A Connect the two together using a longer CAT5e or better network cable. This can be up to 100 meters long.
Method B Conenct the two together using ethernet over power adapters. Others please comment!
Yes the technology you have brought into is FTTC, Fibre to the Cabinet. The connection between your premises and the telephone exchange goes via a local street cabinet. Your connection to the cabinet is by copper cable. Unless you are unfortunate and then it could be aluminium. The cabinet now houses the DSL equipment that used to be in the exchange. Between the cabinet and the exchange is a fibre optic connection shared by everyone that is connected at your cabinet.
Hope this helps.
Dave

Deleting Wireless Router Connection

I just recently moved my wireless router from a different PC to the PC I have in my room, however, I did not uninstall the linksys connection and such from the other PC, I just moved all the wires and my DSL connection wire to the PC in my room. I had to call Linksys to fix my router connection, so that person set up a new connection and a password, but she did not delete the other connection that the router was first running off of. Somehow that router connection (on the other pc) started to allow connection without a password, even though I did not remove the password, I honestly don't know how it happened. Now I am able to connect to my new password protected connection and my laptop that I use in the room can connect to our old connection which is "unsecured", does anyone know how to delete that connection? I was just going to uninstall the program on the old PC and hope that it will work, but I do not want to waste my time if it doesn't work, and I already called Linksys support and paid $9.99 for someone to log onto my PC to set up my new connection. The old connection is interfering with my new connection, because people are connecting to it, since it does not have a password, someone please help!

This is the 2nd thread I've seen with this same question/issue. I would like to know if CISCO is really hearing what we are saying!!!
The questions is HOW DO YOU DELETE THE OLD install?
The questions is not am I secure?
I have had several IT friends see the same issue but unsure if they have researched the support forums on here to get to the bottom of this. So this is my story...
THANK YOU FOR POSTING THIS QUESTION.
I'm having the same issue and have been for several months. It is true what you have stated. Even at my home (now an old network no longer used) that my access point via desktop doesnt show 2 networks. My mobile pc's do!
1 secured (bcse we reinstalled and locked it WPA2)
1 the old install that just "fell off the wagon" unsecured sometime last year.
HOW DO YOU DELETE THE ROUTER IF YOU CAN'T SEE IT?
ignoring that old one, and securing my new is leaving a weak signal for people to use. The kids in my neighborhood sit at the bball courts and use their pc's. When I unplug mine, they leave w/n 10min.
My neighbor tells me today that comcast calls her they see an unsecure linksys (which is my old one). Oddly enough, they are receiving reports that hers (secured network) had been hacked to go to Univ. Studios to dwnload full length movies. SMNT! I cant delete the router from the (once main desktop) PC bcse I dont see it in the list.

Route connect timeout error

Hi,
While accessing our SAP systems with router sting i am getting following error.
timeout occured
Time                             tue May 26 09:25:12
Component                   NI(Network Interface)
Release                        710
Version                         39
Module                         nibuf.cpp
Line                              4765
Method                         NiBufIConnect: route connect '/H/10.124.5.12/S/3299/H/10.129.2.50/S/sapdp01/' timeout after 10000ms
Return Code                  -5
Counter                         1
Thanks & Regards
Raj Kiran

Hi,
Did you get it solved? I am facing the same problem..Timeout occurs when I try connecting to a SAP System..
Thanks

Physical Interface not present in show ip route connected

Hi,
Thanks for reading my post.
I have a reccurent issue with a CISCO881-K9.
My WAN interface is regularly unsuable even if it's UP/UP. I can't even ping the interface from the router itself.
A reboot solves the issue. But now I have time and I'd like to get a proper understanding of what's going on.
The route doesn't appear in "show ip route connected".
Router#show ip interface brief
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0              unassigned      YES unset up                    up
FastEthernet1              unassigned      YES unset down                  down
FastEthernet2              unassigned      YES unset down                  down
FastEthernet3              unassigned      YES unset down                  down
FastEthernet4              X.Y.Z.82    YES NVRAM up                    up
Loopback0                  10.31.129.5     YES NVRAM up                    up
NVI0                       X.Y.Z.82    YES unset up                    up
Tunnel0                    10.32.129.1     YES NVRAM up                    down
Vlan1                      172.22.129.102 YES NVRAM up                    up
Router#ping X.Y.Z.82
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to X.Y.Z.82, timeout is 2 seconds:
Success rate is 0 percent (0/5)
Router#
Router#show ip route
Gateway of last resort is X.Y.Z.81 to network 0.0.0.0
S*    0.0.0.0/0 [1/0] via X.Y.Z.81
      10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
R        10.30.129.0/24 [120/1] via 172.22.129.101, 00:00:08, Vlan1
R        10.31.129.1/32 [120/1] via 172.22.129.101, 00:00:08, Vlan1
C        10.31.129.5/32 is directly connected, Loopback0
      172.22.0.0/16 is variably subnetted, 3 subnets, 2 masks
S        172.22.128.0/24 [1/0] via 172.28.28.254
C        172.22.129.0/24 is directly connected, Vlan1
L        172.22.129.102/32 is directly connected, Vlan1
      172.27.0.0/24 is subnetted, 1 subnets
S        172.27.0.0 [1/0] via 172.28.28.254
      172.28.0.0/24 is subnetted, 1 subnets
R        172.28.28.0 [120/2] via 172.22.129.101, 00:00:08, Vlan1
      172.30.0.0/24 is subnetted, 1 subnets
S        172.30.1.0 [1/0] via 172.28.28.254
      172.31.0.0/24 is subnetted, 1 subnets
S        172.31.0.0 [1/0] via 172.28.28.254
S     192.0.0.0/16 [1/0] via 172.28.28.254
      192.168.48.0/32 is subnetted, 1 subnets
S        192.168.48.247 [1/0] via 172.28.28.254
      192.168.84.0/32 is subnetted, 1 subnets
S        192.168.84.247 [1/0] via 172.28.28.254
S     192.168.101.0/24 [1/0] via 172.28.28.254
R     192.168.104.0/24 [120/2] via 172.22.129.101, 00:00:08, Vlan1
Router#show ip route connected
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
       + - replicated route, % - next hop override
Gateway of last resort is X.Y.Z.81 to network 0.0.0.0
      10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
C        10.31.129.5/32 is directly connected, Loopback0
      172.22.0.0/16 is variably subnetted, 3 subnets, 2 masks
C        172.22.129.0/24 is directly connected, Vlan1
L        172.22.129.102/32 is directly connected, Vlan1
interface FastEthernet4
description WAN
ip address X.Y.Z.82 255.255.255.252
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1300
duplex full
speed 100
keepalive 3
crypto map MYSTREAM-MAP
hold-queue 224 in
end
Router#show interfaces fastEthernet 4
FastEthernet4 is up, line protocol is up
Hardware is PQII_PRO_UEC, address is 4403.a738.3c02 (bia 4403.a738.3c02)
Description: WAN
Internet address is X.Y.Z.82/30
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (3 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:06, output 00:00:35, output hang never
Last clearing of "show interface" counters never
Input queue: 0/224/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     26675 packets input, 1826301 bytes
     Received 12230 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog
     0 input packets with dribble condition detected
     44029 packets output, 8969818 bytes, 0 underruns
     0 output errors, 0 collisions, 4 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     3 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Could you help on this? Or lead me to Tshoot that problem.
By the way the interface 4 is connected to an ISP Modem (TWC in US).
Thanks,
William

Hi,
Thanks for your answer. I've checked the release notes and there is no bug about that.
I think I must use the WAN interface which is fastethernet 4. I'm not able to change the patch cable for now.
What could be the cause?
show version
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 21-Mar-12 00:27 by prod_rel_team
ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
Router uptime is 1 week, 3 hours, 6 minutes
System returned to ROM by reload at 08:12:54 UTC Fri Oct 3 2014
System restarted at 08:14:30 UTC Fri Oct 3 2014
System image file is "flash:c880data-universalk9-mz.151-4.M4.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
If you require further assistance please contact us by sending email to
[email protected]
Cisco 881 (MPC8300) processor (revision 1.0) with 236544K/25600K bytes of memory.
Processor board ID FGL1652265J
5 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
256K bytes of non-volatile configuration memory.
125440K bytes of ATA CompactFlash (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO881-K9           FGL1652265J
License Information for 'c880-data'
    License Level: advsecurity   Type: Permanent
    Next reboot license Level: advsecurity
Configuration register is 0x2102

Belkin wireless router connected but browser could not find the host server

my new roommate has a belkin n wireless router connected to a cable modem which functions perfectly on her pc laptop. i am trying to connect my MacBook Pro to the router using her WEP password. this all works fine and my System Preferences/Network/Status shows that AirPort is connected with full strength, but i cannot load any web pages (i have not yet been able to load any pages at all using this router). the page load error reads "Firefox can't find the server at www.cnn.com" and "The browser could not find the host server for the provided address".
I spoke with Belkin support and they say the router is functioning properly, that is a problem with my mac.
When I go to Network Diagnostics, the status shows all green and says "This computer's Internet connection appears to be operating normally. Are you sure you want to use Network Diagnostics?
Could this be a firewall issue? A couple people have suggested that, but I'm not sure how to fix that.
I have tried rebooting the router and cable modem, rebooting the mac, etc.
any ideas on what settings i may need to investigate??
thank you!
Message was edited by: photoeyeseattle

photoeyeseattle wrote:
how do I know if the router has useful DNS servers? i am looking at the settings of the router on the pc that is online.
Somewhere in the settings of the router should be the DNS servers that it is using. Since the router is offering via DHCP to do DNS translation for your Mac, it must have useful DNS servers listed.
There are "public" DNS servers. I have no experience with it, but this Web page describes one from Google:
http://code.google.com/speed/public-dns/
Supposedly Google has a DNS server at IP addresses 8.8.8.8 and 8.8.4.4 that you might try. Since the DNS server setting on your Mac is grayed out, as a test you might try noting the setting in the "TCP/IP" tab of your AirPort connection item of the Network panel of System Preferences. Then switch from "Using DHCP" to "Manually", fill in the values you just noted, switch to the DNS tab and fill in Google's DNS addresses, and see if things work better.
do you have any other suggestions of where to seek help???
Perhaps a Belkin discussion group?

Can't get DNS for laptop on router connected to shared NIC

I have my router connected to my PC on one NIC that is shared. Another NIC connects from the PC to the cable modem. The laptop is able to see and connect to the shared wiresless router but cannot receive a DNS address. No internet browsing. On the same shared wireless connection I have an XBox that can connect and get a DNS response. Also the PC has no trouble connecting to the internet.

It sounds like your network is setup this way:
modem - PC - router )))) laptop
                                 )))) Xbox
Is this the way your system is set up? If so, why?
Most systems are setup like this:
modem - router - PC
                         )))) laptop
                         )))) Xbox

Linksys router connection to playbook!

Hi all: I am having a problem with keeping the router connected to the playbook. It is a linksky, by Cisco and I have checked everything and nothing is wrong. When I reconnected to the the playbook, I use the WPS to connect to the playbook and everything is ok for awhile and it stops working, does anyone have a solution? Many thanks in advance for ur help, regards, Charlotte Mueller

Have you connected your PB to this router successful previously?

Internet speed impacted when router connected

I have been keeping a constant check on our internet speed, primarily because our Bell Sympatico service peaks and troughs .. my speed without the router is 5600kbps .. when I connect the router however my speed drops to 2,200 .. why is that .... and can it be fixed .. because before I switched to this router, I had a d-link which recorded the same speed with or without the router connected.
I've been giving Bell grief and have a service ticket out, which I may not need it seem to be the router ?
Router is the WRT320N
Message Edited by steelefamily on 10-06-2009 06:12 AM

1) When you said your speed drops to 2200 kbps, I assume you mean your speed when your computer is wired to the router -- is that correct?
2) And I assume by "kbps", you do mean "kilobits per second", not "kilobytes per second" -- is that correct?
3) If the answer to both 1 and 2 is yes, then the first thing to do is simply reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
4) There are several other things that can give you slow speed when wired to the router including:
a) using point-to-point (P2P) software. This is a known cause for router slow downs and disconnections. It can cause problems for several days after use. Stop the P2P.
b) unnecessarily adding a "Domain name" to your router. If your ISP does not require a domain name, erase the domain name from your router.
c) turning on "logging" in the router. Logging is only for diagnostic purposes, otherwise, turn logging off.
d)  Sometimes Linksys routers seem to have trouble synching to some very old modems. The solution is to get a new modem.
e) Some computers will slow if you are using a wired and a wireless connection at the same time. Turn off your wireless adapter.
f)   Improper setup of modem and/or router --- to fix this, we will need more info:
5) Please state your ISP
6) Please state the make and exact model number of your modem (not the WRT320N).
7) Please do the following test:
Power down your entire network. Using an ethernet cable, connect your modem directly to your computer. (Do not use the WRT320N for this test.) Power up the modem and computer. Verify that you have a working Internet connection, then proceed with the following: (Even if your Internet connection does not work, state this, and proceed.)
Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig /all" (with no quotes), then hit the Enter key.   Copy all the results to your next post. To do the copy, highlight the results, then use the copy (Ctrl-c) keys and the paste (Ctrl-v) keys. If your "IP address" does not start with 192.168 , then for security reasons, erase the last half of your IP address.

HT4197 router connection on ipod touch

HOW TO GET ROUTER CONNECTION ON MY IPOD TOUCH

Does the iPod connect to other networks?
Does the iPod see the network?
Any error messages?
Do other devices now connect?
Did the iPod connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

E1200 Router Connecting Dlink DIP-714P+

Dear All,
I am replacing old D-Link DI-714P+ router with E1200.
The old configuration was a printer connecting to D-Link router, and allow for wireless printing.
Therefore, may I know how do I configure E1200 so that I still can print wirelessly, while connected to E1200 network.
Assuming the printer still connected to Dlink router, can we print to E1200 then bridge to Dlink ?
Thank you.
regards,
Chong KK

If you will replace the old router with the E1200 you simply need to configure the router to work with the modem and setup the wireless settings using the CD. If the printer is connected wired to the Dlink router you simply need to disconnect it from the Dlink and connect it to the E1200 router. After doing that the printer should work and you should be able to do wireless printing. However if the printer is wireless capable and you want to connect that wirelessly to the E1200, then you will need to setup the wireless printer to connect to the wireless settings setup for the E1200 router (you can refer to your printer documentation for that).
Now if you will leave the Dlink router connected and if you just want to cascade the E1200 router to it then there is a different configuration for that. Base on my understanding you want to leave the printer connected to the dlink and you would like to connect wirelessly to the E1200 router right? Then you need to connect the E1200's ethernet port (one of the yellow ports) to the Dlinks ethernet port as well. This is called LAN to Lan Connection. To know how to do that then click on the link below:
Cascading (Connecting) a Linksys router to another router
After doing it you can then Configure the wireless settings of the E1200 manually since you cannot setup the router using the CD with LAN to LAN configuration.
Configuring the wireless security of your Linksys Wireless-N router through the web-based setup page

Secondary Router connection problems

I have an ASUS RT-N16 that i am trying to piggy back off of the actiontec. i currently have the ip set different from the default and ip on the fios router. connected LAN (fios) to WAN (ASUS) and no internet access. is there something i am missing? so far FIOS reps have been unwilling to give me solid information on the situation. should i pay somebody to set up this connection? it seems like the should be willing to help since i am still using their service and simply trying to connect an old laser printer via usb. any information is appreciated.
Frustrated User

unite5 wrote:
I have an ASUS RT-N16 that i am trying to piggy back off of the actiontec. i currently have the ip set different from the default and ip on the fios router. connected LAN (fios) to WAN (ASUS) and no internet access. is there something i am missing? so far FIOS reps have been unwilling to give me solid information on the situation. should i pay somebody to set up this connection? it seems like the should be willing to help since i am still using their service and simply trying to connect an old laser printer via usb. any information is appreciated.
Frustrated User
Verizon doesn't officially support anything besides the Actiontec router as they install it. They may provide some assistance for setting up client devices such as computers, however they aren't going to give much help with a second router or adding a USB printer to that router. The potential combinations of equipment that people can install is huge, and to expect Verizon to support anything we users might install is quite frankly unreasonable.
Now, that doesn't leave us users without any support options. Here's some ways you can get this working:
Utilize web based forums like this or other sites to learn from and exchange ideas with other users. Use web search engines as well. You may not find exalt what you need, but you'll learn a lot. This is a good approach for a reasonably technical person.
Read the manuals. Learn about networking protocols either by tacking classes or reviewing online course work. In other words, become very knowledge at networking. This builds on the above suggestion. Great for very technical people and will enable you to tackle most any networking problem.
Hire a local support person to configure your network. If you are interested, have them explain what they did so you can learn from it. If you don't care about what they did, don't ask and be prepared to pay them again if you need to change anything.
You've gotten some great pointers from Anti-Phish. It's up to you where you go from here. Just don't expect Verizon to be any help. It's not part of their service.
Good Luck.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

WRT54GS router connected, but not detected.

I have my WRT54GS wireless router connected just like the Easylink setup guide told me to. It goes through the steps up to the point that it tells me to verify that certain lights are on. They are, so I click next. Here's my problem. On the next step, the computer attempts to detect the router, but fails. I can still connect to the internet through the router on my wired connection. On my wireless conection to my PS3, it obtains an IP address, but can't connect. On my wireless connection to my other computer, it finds the network, but can't connect.
I called Linksys tech support and was told it had something to do with my modem and I had to call my ISP. I called my ISP and they said it was a problem with the router.
I know none of the hardware is faulty, because it worked when the computers were in opposite positions. That leads me to believe it is some setting on this computer, but I have no idea what it could be.
Can someone help?

Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When
it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....

Router connection lost after connecting modem

Router: WRT54GX4
Background: My desktop PC had been connected to the internet through my router and DSL modem just fine. But I forgot my router password, so I reset the router.
Situation: Now my PC communicates with the router fine when the modem is NOT connected to the router (I can ping the router, access the router's Utility screens, etc.). Once I connect modem to the router, though, my PC can no longer ping or see the router. My PC will still connect fine to the internet when directly connected to the modem.
Attempted Fixes: I've believe I've tried every combination of turning off/turning on the equipment. For example, while I have a good PC/router connection, I've connected the modem to the router (and lost the router connection). Then I tried starting out with a good PC/router connection, powered off the router, connected the modem, then powered the router back on (and lost the network connection). I've restarted the PC after connecting the modem to the router, et cetera, et cetera. Every scenarion I try ends up with me losing the router connection to the PC.
Any suggestions would be appreciated.
Message Edited by Mark73Online on 08-26-2007 11:51 AM

After you reset the router to factory defaults, you need to setup the router again. Use the setup disk that came with the router, or setup the router manually if you prefer. It sounds like your "Intenet Connection Type" is not setup correctly.
Please state your ISP.
Also state the make and model of your modem.
Do you have cable modem, or DSL, or ADSL ?
Did your ISP give you a PPPoE user name and password?

Easy VPN on 1710 cisco router connected to a DSL using dyndns

I have a 1710 cisco router connected to a DSL modem at home. Dynamic DNS or dyndns is implemented on it and everything works fine. In order words, I do not have a static IP address.
I would like to be able to configure vpn or Easy VPN on it so that I can connect with my laptop from outside using the cisco vpn client software.
Can someone please post a step by step sample vpn configuration? Something that does not conflict with my configuration. Below is my config. Thanks in advance.
Paul Pagina
PageHut#show run
Building configuration...
Current configuration : 2543 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname PageHut
boot-start-marker
boot-end-marker
no logging console
enable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxx.
enable password 7 xxxxxxxxxxxxxxxxxxxxxx
aaa new-model
aaa local authentication attempts max-fail 3
aaa authentication login default local
aaa session-id common
memory-size iomem 15
ip cef
ip inspect name CBAC-NAME tcp router-traffic
ip inspect name IPFW tcp timeout 3600
ip inspect name IPFW udp timeout 15
ip inspect name IPFW ftp
ip inspect name IPFW h323
ip inspect name IPFW rcmd
ip inspect name IPFW smtp
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
ip ddns update method DYNDNS
[a1]
HTTP
add http://xxxxxxxxx:[email protected]/nic/[email protected]/nic/update?hostname=<h>&myip=<a>
remove http://xxxxxxxxx:[email protected]/nic/[email protected]/nic/update?hostname=<h>&myip=<a>
interval maximum 28 0 0 0
interval minimum 28 0 0 0
vpdn enable
username cisco privilege 15 secret 5 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx!
interface Ethernet0
ip address 172.16.1.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
no ip mroute-cache
half-duplex
interface FastEthernet0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no ip mroute-cache
speed 100
pppoe enable group global
pppoe-client dial-pool-number 1
interface Dialer0
no ip address
ip inspect IPFW out
interface Dialer1
mtu 1492
ip ddns update hostname xxxxx.dyndns.org
ip ddns update DYNDNS host members.dyndns.org
ip address negotiated
ip access-group 101 in
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname xxxxxxxxxxxxxxxxxxxxxx
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxxxxx
ppp pap sent-username xxxxxxx password 7 xxxxxxxxxxxxxxxxxx
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
access-list 1 permit 172.16.1.0 0.0.0.255
access-list 10 permit 192.168.1.0 0.0.0.255
control-plane
banner motd ^C
**This is a my banner***
*************************************************************************** ^C
line con 0
password 7 xxxxxxxxxxx
line aux 0
password 7 xxxxxxxxxxxxxxx
line vty 0 4
password 7 xxxxxxxxxxxxx
end
PageHut#

Hi there,
I check the bug toolkit and I found this one that matches the problem you are describing:
CSCti73763 Bug Details B
large packet drop with ipsec, cef and virtual reassembly
Symptom:large packet drop with ipsec , cef and virtual reassembly
Conditions:large packet drop with ipsec , cef and virtual reassembly
Workaround:disable virtual reassembly or ip cef
1st Found-In
15.0(1)M3
Known Affected Versions
Fixed-In
15.1(3.2)T
15.1(3.3)PI15
15.0(1)M4.4
15.2(0.0.10)PIL16
15.1(1)T2.3
15.1(2)T2.2
15.1(3.15)T
15.2(0.0.18)PIL16
15.1(3.14.6)PIA16
15.2(0.0.1)PIA16
15.2(3.22.4)PIB16
15.1(3)T1.5
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCti73763&from=summary
Hope this helps.
Raga

Moving router connections

Similar Messages

Maybe you are looking for