Hi,
In fact it should work except of maybe a transient connectivity break because of a race condition. OSPF and LDP will start sending hellos and setting up adjacencies and LDP session, respectively.
Once OSPF is converged it will start using the new/reenabled link. OSPF routing decision does not take LDP availability into account. So when LDP is not ready yet, but OSPF decides to send all traffic over the primary link, there are no labels yet (show mpls forwarding-table, search for "untagged"). Thus connectivity for VPN traffic is broken.
One way of overcoming this is to use targeted LDP:
R(config)# mpls ldp neighbor x.x.x.x targeted ldp
This means the LDP session is kept even if the interface is down, as long as x.x.x.x has IP connectivity.
Now all this said, it should recover without manual intervention. Your config looks fine to me. Have you checked, what the underlying problem is?
show mpls ldp discovery ! are LDP hellos sent and received after link recovery?
show mpls ldp neighbor ! is LDP session reestablished?
show mpls forwarding-table ! are labels entered into LFIB after link recovery?
Targeted LDP might still solve your problem, because you would not loose the LDP session.
Hope this helps! Please rate all posts.
Regards, Martin

Similar Messages

I want to resigne an annual engagement ? how to do ? it doesnt work with " more help"! turn turn turn turn over and over

i want to resigne an annual engagement ? how to do ? it doesnt work with " more help"! turn turn turn turn over and over

This is an open forum, not Adobe support... You need Adobe support to cancel a subscription
-start here https://forums.adobe.com/thread/1703848
-or by telephone http://helpx.adobe.com/x-productkb/global/phone-support-orders.html
--and two links which may provide more details, if the above links don't help you
-http://helpx.adobe.com/x-productkb/policy-pricing/return-cancel-or-change-order.html
-http://helpx.adobe.com/x-productkb/policy-pricing/cancel-membership-subscription.html

I book doesnt work with power cord only

Hello. I was just using my ibook g4 and shut it down. When i tried to turn it back on it worked for about 5 minutes then it shut off. I tried taking out the battery and holding down the power button for 5 seconds among other things. I gave up and borrowed a friends battery, he has the same model as me and that battery doesnt work either. I tried just using the power cord only and that doesnt work either. Do i need to take it in to a professional? I've tried just about everything.

Hey Caesar and Welcome to Apple Discussions,
So your header reads:
"i book doesnt work with power cord only "
Is that right? Will it run only on the battery?
If so this is from the manual:
"The computer runs with battery, but not with the power adapter plugged into
wall outlet
1. Try known-good power outlet.
2. Try known-good power adapter and power cord.
Note:
Verify that power adapter connector glows amber or green. If the power
adapter light is green, turn over the computer and press the battery button. The
battery lights should glow green and stay on if the power adapter is operating
correctly.
3. Reset the power manager by pressing the key combination Control-Option-Shiftpower.
Warning: Make sure you do not hold down the "fn" key when resetting the
power manager.
Warning: Resetting the power manager means you will also need to reset the
date and time (using the Date & Time control panel).
4. Replace DC board.
5. Replace logic board."
and it would help to know exactly which iBook you have but this is pretty generic.
Richard

Why is the fb video call doesnt work with macbook?

why is the fb video call doesnt work with macbook?

Hi
Just to correct GerdW - the vis of a polymorphic vi do not have to have the same output.
Have a look at the vis I attached. I just pass a dbl to a polymorphic vi and get a dbl in one vi and a string in the other.
The real problem is that the vi has to be set to the necessary type. If there are different inputs you just can wire them to the polymorphic vi, but this does not work with the outputs, so you have to set the type.
Hope this helps.
Thomas
Using LV8.0
Don't be afraid to rate a good answer...
Attachments:
Polymorph.zip ‏14 KB

Seagate 1.5TB doesnt work with mac

hi, i have a seagate external hard drive 1.5 TB, i generally use it for my windows laptop. now i bought a mac and it doesnt work with my mac. Am i doing some thing wrong..?

Are you planning on using the drive with Windows? If no, then use Disk Utility in Applications/Utilities to reformat the drive. Formatting erases contents on a drive. Copy the data to another source before formatting.
Format the external drive as Mac OS Extended (Journaled) - Partition Map Scheme: GUID
Select Drive (top name) then click on Erase tab.
Under Format select Mac OS Extended (Journaled)
This should format as GUID when erasing but sometimes you need to click on an Advanced tab and select GUID.
If you do plan on using the drive with Windows machine, format on Windows machine as exFAT.

Time capsule doesnt work with telia bredband no wifi

Time capsule doesnt work with telia bredband no wifi. Time capsule and its wifi worked in the beginning, but now it doesnt. I have tried everything without success.

There is no question.. so if it is a statement of resignation.. then if under warranty and faulty Apple will fix it/replace it.. if not dead you will be given it back.
Are you using Lion? If so did you download 5.6 airport utility?
Plug the TC into a computer by ethernet.. hold in reset for 10sec.. and then redo the setup.
Give TC and wireless short names and no spaces and no special characters.. lock the wireless to manual a/n-b/g and fix the channels.
Then if it doesn't work most likely faulty. Otherwise it is just setup is wrong.

Cmss 3d doesnt work with dolby digital live pack

0cmss 3d doesnt work with dolby digital li've pack4 From the page of Dobly Digital Li've pack
"Stereo content (MP3, WMA, CD audio or games) that is transformed into 5. surround sound using Creative CMSS-3D or DTS Neo:PC can also benefit from this encoding scheme that will further enhance the entertainment value of your Sound Blaster X-Fi."
with that said, i bought the pack that has both DDL and DTS Interacti've. but while playing music my reciever only gets front left and right channels. No sound comes from the center or rear channels. This is with CMSS 3D on. With analog all 5 speakers work. Before installing this pack, my reciever got PCM input from the optical line. Thus only the front channels working. now with this pack the speaker recognises that the signal is Dolby or DTS yet, only the front channels work. in short there is no difference with this pack.
could someone please explain to me how to get the whole 5. working with Dolby or DTS
thank you
Sound Blaster X-Fi Platinum, Driver 2.8.003
Windows 7 x64 Build 700

thank you for the promp reply
the problem was with the reciever. just a change in setting was all it took
but now i have anoter problem
how do i bypass dolby and dts signals from movies to my reciever
before i simply had to set spdif out as default sound device and set ac3filter to spdif passthru
now the driver panel tells me that SPDIFOut will be exclusvely be used by DTS Interactiv. it doesnt pass the signal through from Media player classic or powerdvd.
am i expected to turn off DTS Interacti've or DDL when watching a movie and needing to pass on the signal?

Related Link doesnt work with Multiple Helpsets

Robohelpx4.1 is used as the authering tool to generate our help files in OHW format. We have different projects creating one helpset file each and it is merged in the ohwconfig.xml. Each helpset has its own link,map,index,Toc files created by robohelp. The link file created by robohelp has the linkitem id created in seq order and names as Link01,Link02,Link03..... .
The link file of other helpset also has the same structure and ids. (The linkitem id's are not unique across the helpsets)
But the related link doesnt work properly when more than one helpset is configured, for both the options of combined book and separate books. Links get mixed up and shows topics of other links.
Is there anyway this can work ?

Link Problem with Multiple Helpsets

MSI GF4 Ti-4200 doesnt work with WindowsXP

I can't get the MSI display tools to work - it crashes,
the vbios.dll doesnt load, it also crashes.
the tv in doesnt work ,it crashes
the tv out doesnt work ,it crashes.
all the supplied software also crashes "application has encountered an error and cannot continue. sorry for any inconvenience"
the intervideo software (windvr, wincoder, winproducer) and MSI PVI software all crashes as well.
what's the deal with this stuff? ?(
I have a Dual AMD athlon Tyan thunder k7 motherboard,
MSI Ti-4200-VTD video card and MSI tv anywhere card.
is there any resolution for this?

I'm sorry gfilitti if I don't have my system listed, but I thought my question was pretty simple...
Has ANYONE been able to make the InterVideo WinProducer 2 software, that comes with the retail version of the MSI G4Ti4200-VTD64 card, work successfully under the Windows XP Home or Pro operating system?
If the answer is YES, then I will begin investigating why my system can't.
If the answer is NO, then I only ask for other people's recommendations of what software WILL work in place of that. I NEED those functions to work. That's why I paid extra for the VIVO.
All we've heard so far in this thread are NO votes. I would like to see just how widespread this is. If I can find ONE person who claims it works fine on his/her computer under Windows XP, then my NEXT question would be if they had to do anything different to make it run, or was it just a straight install? Did they add the program patch available from the MSI website? See where I'm going with this?
If you would REALLY like my system details, here ya go...
========================================
CASE - ANTEC SX1000II with 4 internal 8cm fans
POWER SUPPLY - ANTEC 400W "True Power" w/dual fans
MOTHERBOARD - MSI 645E MAX (MS-6547 Ver 2.0)
BIOS - AMI Ver 3.2 (10/21/02)
PROCESSOR - PENTIUM 4 2.0aGHz (Rev/Step 2/4(9) )
MEMORY - 1 Corsair 512MB DDR RAM (Winbond chips)
DISABLED IN CMOS - FLOPPY Controller, AUDIO Device, MODEM Device, Serial Port B, MIDI Port, and GAME Port
AGP SLOT - MSI G4Ti4200-VTD64 - IRQ 16
DRIVER: MSI 31.00
CAPTURE DRIVER - nVidia 1.08
SLOT 1 - Creative SB0090 Audigy Sound Blaster - IRQ 17
DRIVER - Creative 3.0.0.18 9/20/02
SLOT 1 - Creative SB1394 FireWire Controller - IRQ 18
DRIVER - MS 5.1.2535.0 7/1/01
SLOT 2 - NIC #1 D-Link DFE-530TX Ethernet - IRQ 18 (LAN)
DRIVER - REALTEK RTL8139 5.396.0530.2001
SLOT 3 - Adaptec 29160N Ultra160 SCSI Controller - IRQ 19
DRIVER - Adaptec 6.2.0.0 3/19/2002
SLOT 4 - EMPTY
SLOT 5 - MSI SYSTEM D-Bracket
SLOT 6 - NIC #2 NetGear FA312 Ethernet - IRQ 18
DRIVER - Windows XP Pro native driver
NOTE:
NIC #1 is for home LAN
NIC #2 is for Alcatel SpeedTouch External DSL modem
SCSI DRIVES:
ID 0 - COMPAQ (Seagate) ST318451LW, 18GB, 15K RPM
ID 1 - QUANTUM Typhoon Atlas II, 18GB, 10K RPM
ID 2 - Seagate ST39103LW, 9G, 10K RPM
ID 3 - Plextor CD-RW PX-W1219S
ID 4 - Toshiba DVD-ROM SD-M1201
ID 5 - EPSON Perfection 1640SU Flatbed Scanner
ATA/ATAPI DRIVES:
Primary Master - No Connection
Primary Slave - No Connection
Secondary Master - MATSHITA LS-120 Ver F523
Secondary Slave - No Connection
USB DEVICES:
DIAMOND SupraMAX 56K V.92 Model:SUP2920
Generic Flash Memory programmer and other assorted USB devices on occasion.
MONITOR - HITACHI SuperScan Pro 21 w/5-BNC input
========================================
BTW, I would think when investigating a program's FLAT refusal to run, that the MOST important things aren't listed in these signature files. It has to do with what ELSE is running at the same time. Which services are running and which are NOT? What memory resident programs are loaded at boot-up? Any service packs installed? How about any security patches from Microsoft? Which anti-virus software (if any)? Which DirectX version? Personal firewall? Etc., etc.
Granted, the hardware DOES have a factor, but I feel all of these are MORE important factors than the speed or brand of a persons hardware. I look at the signitures more as bragging rights than anything else.
Now, this is just my opinion and may not reflect the feelings of the more sane people around me.
Cheers!

Logitech Cordless Optical Mouse doesnt work with mac os x 10.4.5?

I just bought a Logitech® Cordless Optical Mouse in japan to use with my powerbook running os x 10.4.5...the mouse doesnt seem to work with the native bluetooth system. so I plugged in the supplied reciever and could get the mouse to move the cursor, but only that. buttons dont work. I down loaded some kind of device manager from the logitech web site but just as the apple bluetooth manager it does not "discover" the mouse.
I noticed that the system requirements for the logitech device manager is osx 10.3 - 10.4.2 so im wondering if my system is to new for this product.
all this i found out after i bought the mouse, and it is a little irritating...it said it was mac compatible on the box...
should I be waiting for an update from logitech or apple concerning this problem.
or is there an easy fix/ anyone else have this problem?
thanks
©

Hi, © ! — or do you prefer Ulfur?
What model? "A Logitech® Cordless Optical Mouse" covers a lot of territory. For example, I have a CordlessOptical11 mouse that's several years old — and IrDA, not Bluetooth. This Logitech page contains a chart defining the name and "device model string" for each product, based on the M/N stamped into the bottom of your mouse. Better safe than sorry: Logitech's support — particularly for Mac folk — can be somewhat challenging. [1]
From there, you might try to confirm that you have the correct driver from Logitech's Support »» Downloads »» Mice page —
— but, Oops! — unfortunately, it may only link to Windows-compatible drivers.
Logitech has used their own patented RF technology for years — and some of their "Bluetooth" products "may not" actually provide Bluetooth functionality in Macs. (OK, that was tongue-in-cheek: I really mean "do not.") The mice usually work, though.
AFAIK, Logitech Control Center 1.6.2 is their latest driver for USB mice. (They have other mouse drivers, too.)
However, as this page explains, their V270 Bluetooth mouse supposedly doesn't require a driver separate from what's provided by Apple.
You may want to search this forum for differing views on this. Also, go to this Logitech user forums page and click to select the Macintosh forum. I won't deny you the (dis-?)pleasure of reading about others' experiences...
[1] Sorry, I don't mean to be as discouraging as I've probably made things sound. Most Mac folks have actually had pretty good experience with Logitech USB and Bluetooth mice — but Logitech Support's attitude toward Mac users could be improved. Please check things to confirm what's what — then post back, and I — or someone else who's using an MX900 or MX1000 or V270 or whatever Logitech mouse — will try to help further.
Looking forward to hearing back from you,
Sincerely,
Dean
[2] The links I've provided all work within Logitech's US website (I just tested). If appropriate, you may want to start fresh from the Logitech home page and find comparable international pages.
[2,059 ⊥ 3,455]

Video slide bar doesnt work with streaming video

I am converting from progessive video to streaming video. I am using a streaming site. the video plays fine through when called up in preview or published but the silide bar doesnt work for the video (backwords or forwards in the video)...works fine in a progressive download. I am using fv4.
Any Ideas?

I had no problem getting the video to stream inside my project...my problem is that when I use the "insert a fv or fv4" feature and insert the proper link, captivate uses a different player (the video shows up in a separate window in the slide) and the player doesnt have a progress bar. The progress bar in the skin itself will not (the player that comes with the slide) operate. Therefore, all I can do is start and stop the video....I need a working slide bar so the student can navigate ( especially backwards) the video....any Ideas?

HP DesignJet 800 24" doesnt work with Mac OS 10.7 Lion

Having just upgraded to Mac OS 10.7 Lion, my DesignJet 800 24" no longer shows up on the network. Every time i upgrade my Mac OS this happens, in the past i've had to install previous version drivers to get it to work as the current ones never do - as is the case with the current one for lion. But this time that's not working and it's not even visible on the network. The HP help pages (of the links that actually work) basically say it's up to Apple to provide an update to their OS to make it work - Not good enough, it's an HP product.
If anyone can suggest any work arounds for this i'd be grateful as i don't have time to keep messing about with this.

OK, i have been reliably informed by a third party that the 'Mac_OS_X_HP_Designjet_Raster_Driver.dmg' (available from HP's 'Support' section) for lion catagorically does not work. The only way to get this printer to work is to connect to it via another mac running OS 10.6 (snow leopard) using bonjour, whilst running the Driver for 10.4 on that mac, which was the only way to get it to work for the last upgrade.
Since OS 10.4, HP have maintained the driver comes bundled with Mac OS and therfore didn't have one to download from the support site (until now - which, did i mention? - doesnt work!), but this is not the case (the PS version does), but not the standard version.
Come on HP sort it out.

ITunes doesnt work with my iPod!!! Help please!

ok...i have tried to plug my iPod into my computer lately, and iTunes doesnt recongnize that my iPod is plugged in!!! i have pretty much de-bugged the problem...its not any of my USB ports b/c other hardware (digital camera etc...) work in them...and its not the computer...but it could possibly be iTunes. if i delete and re-install my iTunes software do i loose all my songs? and w/out loosing all my songs etc is there anything i can do to fix this?
i have also tried resetting my iPod multiple times, but that doesnt work so...the only other thing i can think that could have happened is: i got an iHome a few months ago, and ever since that i have had the problem...so that could have messed something up...can u help?

Does the text on your iPod show up grey in iTunes? Grey text when you look at the content and lock symbol at the bottom of the screen simply shows that your iPod is set to "automatically update songs and playlists". . If you want to access your iPod directly, play it through your iTunes, connect it to a second computer etc. you just need to change the update method to "Manually manage songs and Playlists" in the iPod preferences. For more detail see this tutorial: Managing Your Songs Manually
One thing to be aware of with manually updating is that the iPod also has to be manually ejected before the "Do Not Disconnect" message will go away. Safely disconnect iPod
For info: iPod 101
The iPod offers three ways to transfer music from your computer. You can select one of the following update modes from the iPod Preferences menu in iTunes (Edit=>Preferences=>'iPod' tab):
1) Automatically update all songs and playlists. This is the default mode, in which your entire music library, including playlists, is automatically synced to your iPod. If the music library on your computer exceeds the iPod storage capacity, you are prompted to select a different update method.
2) Automatically update selected playlists only. With this option, iTunes automatically copies the playlists you have selected to the iPod when you connect it to the computer.
3) Manually manage songs and playlists. You can also choose to transfer music to the iPod manually. This allows you to drag and drop individual songs and playlists from iTunes to the iPod.

Ios 8 not working with chevy link

I upgraded my ipad 3 and iPhone 4S to IOS 8. After the upgrade neither device works correctly in my Chevrolet vehicle via Chevy Link. Both devices worked perfectly with Chevy Link when I was using IOS7.
When I plug in my ipad or Iphone it will connect and play songs but as soon as I select a playlist it displays an error message in my vehicle information screen. When you click "OK" to clear the message the device is immediately disconnected from Chevy link and the radio goes back to XM.
Any suggestions how to remedy the situation? As I said before, all of my Apple devices worked perfectly under IOS7.

After having the same problem with my 2013 Chevy Equinox, I did a factory reset of my iPhone 5s and re-installed IOS 8 from scratch.
I used my iTunes backup to restore my apps, contacts, photo ..etc
Since I did that, I was able to connect my phone via bluetooth to my Chevy Equinox, make phone calls, listen to music ..etc
So far so good. I made about 10 calls, stopped the car, restarted the car and reconnected the phone and it worked.
I wonder if the upgrade from IOS 7 to IOS 8 is not working properly and causing problems with Bluetooth. It seems that a full install after a factory reset fixed my problem.
Hopefully, it is the end of the nightmare. Good luck.

Cannot get my Microcell tower to work with Century link

Please HELP!!My microcell tower is not working. At&t says it is because ports are not open with Century Link. Century link suposedly opened them up but they are NOT open.... Can anyone walk me through how to open those ports properly as I am about to lose my mind. I have spent 10 hours on the phone, in 2 days, between At&t and Centurylink!!!

Is it all four ports or just port 4500? Is this a new MicroCell of did you buy it from eBay?
If the ports truly are blocked then unfortunately it's between you and CenturyLink to open them up. AT&T can not force an ISP to open up the ports nor can they determine if the ports are closed on the ISP side or it's an upstream switch that has failed.
There is no way on the consumer side of the things to open ports other than ensure that the router is configured correctly and is freely passing data to and from the required ports. That again is up to you and CenturyLink to determine if the router is configured correctly. There are just way too many routers, firmware upgrades, LAN setups etc for AT&T to keep track of and current with. Besides, they don't want to be responsible for hepling someone configure their LAN in case something goes wrong, which makes perfect sense to me. If there is someone here who has CenturyLink and is willing to walk you thru checking and configuring your router that's great. Otherwise you will have to work that out youself. I know this sounds harsh but that's the reality of it.
Quite often if the ISP supplies you with a router/modem it's pre-configured to work with their system and that might not be compatilble with the publicized AT&T MircroCell router requirements, which are fairly basic.
Which MicroCell do you have and what is the light pattern on the front?

MPLS doesnt work with edundant link

Similar Messages

Maybe you are looking for