MPLS Vrf opsf interfaces not working

P/PE router VRF ospf interfaces unable to receive or advertised routing to and from CE router.
Config attahced.
Routes from PE VRF nortel shld be forwarded to CE router
So are routes from CE 50.50.50.0 network
Any ideas?

Hello,
Looks to me as if you did not start the ospf process in the VRF. So adjust the config according to:
interface Serial2/0
description MPLS VRF 1:1 connection to Cisco 2611 PPP
ip vrf forwarding nortel
ip address 200.0.30.1 255.255.255.0
encapsulation ppp
clock rate 128000
interface FastEthernet4/0
description MPLS connection for vrf Nortel 1:1
ip vrf forwarding nortel
ip address 70.70.70.1 255.255.255.0
duplex auto
speed auto
no router ospf 1
router ospf 1 vrf nortel
network 200.0.30.0 0.0.0.255 area 0
network 70.70.70.1 0.0.0.0 area 0 !In case you want OSPF over this interface as well
With the current config I would assume that you do not see an OSPF adjacency on the CE.
Hope this helps! Please rate all posts.
Regards, Martin

Similar Messages

My audio interface not working with my IMac

My audio interface not working with my IMac

Have you tried > Apogee Electronics > Apogee Support & Product Downloads

BBA Spread Sheet Interface Not Working.

Hey,
I am trying to upload Balances through BBA Spread Sheet Interface,but its not working
Please can anybody tell me what excel settings should i have,or any relevant stuff which could help.
Regards,
Adil Hussain

Actually when i try to upload batch after adding employees the file is not uploaded . How do you upload the batch? Please mention the navigation path along with the steps you follow.
Sometimes file is not downloaded or it is not opened in excel.
Various errors appear during this process. like ORA-20001, Assignment id in not correct format etc.Please post the exact error message.
Please can you also give me any document reference which gives details about Excel settings for using BBA and BEE spreadsheet interface along with any application settings that should be donePlease provide more details so we can suggest.
Thanks,
Hussein

RS485 LabVIEW interface not working with a constant

I need to control an RS 485 interface (not a National Instruments device).
I found a vi written by a colleague which I have attached.
This works perfectly, so I used a probe to identify the value being generated, and used this to replace the variables with a constant.
Now the vi doesn’t work. It runs, but the device it is connected to no longer activates. Then I found that by replacing only one variable with the constant, and keeping the other as a variable kept the vi working.
Can anyone offer any suggestions please ?
Of course, where I really want to get to is a vi that just reads and writes to a non-NI RS485 interface.
Many thanks.
Attachments:
RS485_usb.vi ‏55 KB

Using NI Measurement and Automation Explorer, I sent vset50\n and the instrument responded correctly by going to position 50.
Using the 485 example http://zone.ni.com/devzone/cda/epd/p/id/2674 202314.vi The documentation states that this example will only work with National Instruments RS-485 interfaces. I don’t have and NI 485 and not sure what difference it will make.
In 202314.vi I enabled the termination character since RS485_usb.vi ‏55 KB uses this and it works. Not sure what to do about Assert DTR and transceiver mode so I tried all combinations but kept getting error code 1073807330.
I looked at (Help>>Find Examples..>>search term "485"), but couldn’t pick anything out that I could apply here.
Yes, the randome numbers are now string constants in the block diagram. The string constant, now including \n, is placed at the VISA write input.
I’ve used Measurement and Automation Explorer to send the same command repetitively and there is no problem with this, the instrument jiggles back and forth and rests at the original position.
When the instrument doesn’t work, the vi completes without errors, but there is no instrument activity.
Any thoughts would be appreciated.

Elite pro interface not working

I have just installed my elite pro card. The interface is not working. There is no power light that comes on it and also the remote is not working. The internal sound card is doing ok.
I have windows 7 on my new computer with 8 gigs of ram.
In Cakewalk Sonar 7 and also in Band In A Box, the sound card is listed but there is not listing for "midi input".
Can someone help me?
Thanks
Mike W.

Hi,
tried uninstalling the Setpoint-Software, tried connecting the Keyboard to USB instead PS2, tried a different PCI-Slot for the Soundblaster - all with no Luck :-(
The Logitech Devices are:
Logitech MX 300 Cordless Desktop ( MX000-Mouse not in Use )
Logitech G7-Lasermouse cordless ( with own Recei'ver )
Setpoint Version 2.42a
(Also tried to update the Motherboard-Bios to the latest Vers. 0 which gives me one more Issue - Memory only running at 333 Mhz )
Any more Idea ?
Perfi

SX10 web interface not working

Hello,
SX10 web interface is not working, the sx10 is pingable and registered to CUCM but the web interface gui is not working, my current software is TC7.3.0.8cb420c.
In the meantime I'm trying to get a newer software.
Any ideas?

Is web access enabled for the device in CUCM? If you go into the device in CUCM and search for "Web access" you should find the option under the phone configuration page.

Interface not working properly

Hi to and thanks to every one who r reading my problem
My interface is not working and showing the error if i stop and start the soa server and managed servers.
i am getting the below error
The composite OtmVoucherToOracleApInvoice (1.0) is not available.
This could happen because either the composite has been undeployed or soa-infra has not yet loaded this composite.
Unable to find a WSDL that has a definition for service {http://xmlns.oracle.com/OtmVoucherToOracleApInvoice}OtmVoucherToOracleApInvoice and port OtmVoucherToOracleApInvoice.
Please make sure that the port attribute for the binding defined in the composite file is correct by checking the namespace, service name, and port name.
In addition, check that the WSDL associated with the binding namespace is imported and currently reachable (check the import nodes at the top of the composite file). Finally, validate the HTTP proxy settings for the server.
After restart the server only i am getting this problem.
If once again i deployed it is working properly.but once i restart it is not working i have to deploy again .
why it is showing above problem when ever i restart the servers,
pls help any one who r good in this.thanks in advance.

Hello All,
Thanks for the update,
Hello Naveen as per suggestion i checked ,but i found nothing in wrong..
The said interface should execute once in daily, and when I saw the logs for yesterday(19th), it showed only 1 message displayed success for Reciever system RP1(Live Production).But for the other reciever system RY1(Branched) of that particular sender interface doesn't show any log either success nor failed.
When I checked in CC monitoring for that particular reciever channel(RFCRecieverR3 (RY1)) ,it shows the log but I am unable to trace the problem..
here is the log:
Receiver channel 'RFCReceiverR3' for party '', service 'RY1' (internal name 'RfcClient[RFCReceiverR3]')
Client data: {jco.client.lang=PT, jco.client.snc_mode=0, jco.client.client=871, jco.client.passwd=******, jco.webas.ignore_jdsr_error=1, jco.client.user=xirfcuser, jco.client.sysnr=11, jco.client.ashost=ashb01wa46qa}
Repository data: {jco.client.lang=PT, jco.client.snc_mode=0, jco.client.client=871, jco.client.passwd=******, jco.webas.ignore_jdsr_error=1, jco.client.user=xirfcuser, jco.client.sysnr=11, jco.client.ashost=ashb01wa46qa}
Current pool size: 0, maximum pool size : 10
Can any one kindly suggest me on this..
Best Regards
Rakesh

Time Machine Restore Interface not working (all else seems fine)

I needed to get into Time Machine the other day to restore a file I acccidentally deleted. I entered Time Machine to resore interface. The timeline on the right shows all the past backups but the I was not able to call on any of the backup dates and times. The two arrows to the bottom right of the screen did not allow me to sift through the windows either. I know that the Time Machine is working and creating backups, and when I go through Finder to the disk, all the backups are there. I was able to restoree the file I need using Finder and that was no big deal. But that still leaves non-working restore interface which is something of a nuisance. Does anyone have the same problem?
I am using MacPro 4.1 running OS X 10.9.3. My TM setup is to internal dedicated HD, RAID1 set up via disk utility. The disk size is 2TB and currently has about 1.6TB of data (400GB free).
Any help would be appreciated,
Thanks in advance,
Heidi

I feel exceptionally stupid.
The default window that appears on the restore interface was set to a particular folder from a drive that I do not backup on Time Machine. I was trying to go to the date that I wanted to restore from first instead of navigating to the file I needed to restore. Once I chose one of the drives/folders that I back up on Time Machine, all was fine. I wish Time Machine would make the distinction obvious by graying out excluded items right away (when you go back in time, that does happen but not in the 'present' screen).
Hope above helps in the future for those who may encounter the same problem before having had their first cup of morning coffee.
It is good to know that Time Machine is working as it should, and I count myself one of those fortunate ones who do not have to use Time Machine to restore files that often (hence this elementary question: file under "my computer's not working because I didn't check to see if it's plugged in before calling customer service").

Focusrite Saffire interface not working with FCP 4?

I can't seem to get my focusrite saffire audio interface to work properly with FCP? It works fine with all other apps (itunes, QT, Logic etc) and all the other Studio apps (Motion, DVD Pro and Soundtrack Pro) - but in Final Cut the sound is 'distorted' and 'jumpy'? All focusrite and FCP software is upto date.
Has anybody else had this sort of problem? Is anybody happily using the saffire with fcp? (I can't seem to find any on the search!)
it seems strange that it wont work with fcp but work with the other apps of the package? I can't see any sort of settings in fcp to solve this issue? Any help?!

I am actually only using it to play back audio 'syncd' with picture straight off camera or importing clips from quicktime/DVD's etc. in FCP - it is this that I can't hear correctly? (all the clips are fine by the way played in other aps etc)
Yes, editing is done in Soundtrack Pro or Logic Pro (used to have pro-tools mbox - but decided to ditch it and go down the Logic route with another interface!) - but I expect to be able to hear basic audio with picture in FCP?
Sample rates are matched?...

USB Audio Interface not working anymore

I have a Presonus Audiobox USB Audio Interface. Worked perfectly until I updated to Mavericks, now I get a screeching noise when used and the sound switches to the built in Mac sound.
So then I reboot and it does it again. The Audio box doesnt have any software since its a plug and play. Any help?

Hi ketpiano!
I have an article here for you that may help you resolve this issue:
Macintosh: Solutions for noise in the audio signal
http://support.apple.com/kb/HT2743
Thanks for using the Apple Support Communities!
Cheers,
Braden

Radius source-interface not working ?

I'm running IOS 150-2.SE2 on 3750-X switches.
In my config, I have the command:
ip radius source-interface Loopback1
but all radius requests still have the source IP address of the "nearest" interface, not the loopback interface.
Interface Loopback1 is up and is pingable from the radius server.
Any suggestions ?
Thanks,
GTG

The only command I can see for controlling radius source address/interface is that global ip radius source-interface command.
My full AAA configuration is:
aaa new-model
aaa authentication login default group radius local
aaa authorization exec default group radius if-authenticated
aaa authorization network default group radius
aaa accounting exec default start-stop group radius
aaa accounting system default start-stop group radius
ip radius source-interface Loopback1
radius server radius1
address ipv4 192.168.1.1 auth-port 1812 acct-port 1813
key 7
GTG

Fedex Interface not working after upgrade

Hi gurus,
we are calling Fedex Ship API through RFC, to get the shipping label and will be printed from SAP.
fedex will send the Shipping label in binary format which is combination of characters and hexa.
after upgrading to ECC 6.0, this is not working.
best regards
rajesh

> fedex will send the Shipping label in binary format which is combination of characters and hexa.
> after upgrading to ECC 6.0, this is not working.
This is a statement as "My PC is not working, please help."
The appropriate answer would be: "then you have to find the error".
Without additional information what exactly is not working when, providing logs etc. it's just impossible to suggest something.
Markus

Simple VRF+BGP lab not working

I have set up a simple lab:
router A - 7200 IOS 12.2(27) JS
router B - 2611
There is a serial link between A and B.
On A the serial interface is in VRF.
The B router has no VRF - just ordinary IP.
I am trying to set up eBGP between them.
But the session does not start.
The A config:
ip vrf v2
rd 7:2
route-target export 7:2
route-target import 7:2
ip cef
interface Serial2/0
ip vrf forwarding v2
ip address 192.168.25.5 255.255.255.0
router bgp 65005
no synchronization
bgp log-neighbor-changes
no auto-summary
address-family ipv4 vrf v2
neighbor 192.168.25.2 remote-as 2
neighbor 192.168.25.2 activate
no auto-summary
no synchronization
network 192.168.6.0
exit-address-family
I have done some tests:
Ping from B to A works.
Ping vrf from A to B works as well.
telnet from B to A on port 179 gets RST.
telnet /vrf from A to B on port 179 works.
Debug on B shows session establishment attempts, but
with TCP RST response.
Debug on A shows the neighbor is Idle - no attempts.
On A:
sh ip bgp nei
BGP neighbor is 192.168.25.2, vrf v2, remote AS 2, external link
BGP version 4, remote router ID 0.0.0.0
BGP state = Idle
Last read 02:03:54, hold time is 180, keepalive interval is 60 seconds
Connections established 0; dropped 0
Last reset never
No active TCP connection
I know, that I am new to the VRF stuff, but it is very basic case. What am I doing wrong?
Michal

I have solved the problem.
The keyword is "bgp router-id".
I had no "normal" interfaces, all were VRF ones.
IOS apparently uses by default only IP address
from "normal" interface as a bgp router ID, so:
#sh ip bgp vpnv4 vrf v2
BGP table version is 1, local router ID is 0.0.0.0
As I have forced the ID (bgp router-id ...) all the sessions got up.
Interesting case.

Interface Not Working as I Thought

I thought I understood interfaces pretty well, but I've run across a problem that makes me think otherwise. I defined the following interface:
public interface OffsetObject {
Offset getOffset();
void setOffset(Offset offset);
}Then I implemented it:
public class PathRelatedObjectPointOrientation implements OffsetObject {
   private Offset offset;
   public Offset getOffset() {
      return offset;
   public void setOffset(final Offset offset) {
      this.offset = offset;
}Then I have a method in a base class that uses it:
protected void discardBadOffsets(final List<OffsetObject> list) {
   .. some work done here
}Here's where the problem appears. When I try to call the method, I get a compile error:
    final List<PathRelatedObjectPointOrientation> expected = Efm110.findPROPOs(propo, false);
   discardBadOffsets(expected);This gives the compile error message: The method discardBadOffsets(List<OffsetObject>) in the type ApiPortTest is not
applicable for the arguments (List<PathRelatedObjectPointOrientation>)
What am I doing wrong"?
Edited by: Dick_Adams on Jan 29, 2009 11:20 AM
Edited by: Dick_Adams on Jan 29, 2009 11:22 AM
Edited by: Dick_Adams on Jan 29, 2009 11:23 AM
Edited by: Dick_Adams on Jan 29, 2009 11:23 AM
Edited by: Dick_Adams on Jan 29, 2009 11:24 AM
Edited by: Dick_Adams on Jan 29, 2009 11:24 AM

You probably understood interfaces correctly. Where you still have a bit to learn is generics.
Try replacing
protected void discardBadOffsets(final List<OffsetObject> list) {
   .. some work done here
}with this:
protected void discardBadOffsets(final List<? extends OffsetObject> list) {
   .. some work done here
}The difference between a List<OffsetObject> and a List<? extends OffsetObject> is that you can add elements (of type OffsetObject) to the former, but can't add anything to the latter.

Mgmt Via Dynamic Interface not working on 5505 version 7.2.111.3

Folks,
         I have posted this question a couple of times on the forum but did not get a solution. I am trying to manage my 5508 controller from a dynamic interface which is assigned to port 7 of the controller. I have a switch connected to that port which has a PC on the same subnet as the dynamic interface. From the PC, I can ping the dynamic interface IP Address, but can not telnet,SSH,http or https to it. There is no clear doc that specifics how to effectly use the command "config network mgmt-via-dynamic-interface" command.
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Interface Name                   Port Vlan Id IP Address      Type    Ap Mgr Guest
173                                      7    173      172.16.101.100 Dynamic Yes    No
management                         1    172      172.16.100.100 Static Yes    No
service-port                           N/A N/A      0.0.0.0         DHCP    No     No
virtual                                    N/A N/A      1.1.1.1         Static No     No
7 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
Any guidence would be highly appreciated.

Im having a similar issue and have 2 TAC cases open.
TAC CASE#1: issue is that even when disbaled I can still access the dynmic interface via HTTPS/HTTPS/TELNET/SSH. But this is on a WISM1.
Thanks a lot for your quick and prompt response, I see that there is an internal Bug with an ID CSCty32586.
I see that the bug is fixed told be fixed in 7.0.230.0, but it’s not fixed. The bug is fixed in 7.2.x version.
I understand that you are using Wism on which 7.1.x version and above is not supported.
As 7.0.235.3 is released recently to overcome some of the changes and to fix some of the Bugs with older version on these devices.
Kindly try to upgrade the software version of the WLC to 7.0.235.3 and check the compatibility.
Please do let me know in case of any concerns and I will be glad to assist you.
TAC CASE#2: Just like you I can not access the dynamic interface. Still working that one .. The holiday dropped when I just opened that case.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

MPLS Vrf opsf interfaces not working

Similar Messages

Maybe you are looking for