MRS - Resources and demands are not visible in the Planning Board
Hi Friends - I am working on the the MRSS 610. We have installed it on the our ECC 6.0 as an add-on. We have configured the system as per the configuration guide.
But when I am accessing Manageru2019s Planning Board - /MRSS/PLBOMGR , using the Organization unit, I am getting Notification saying that the resources assigned to the Organization unit are not available in the MRS.
"Resource 00000000010000000000000000000000 not yet created in the WFM Core"
The details of the Error message
"Resource 00000000010000000000000000000000 not yet created in the WFM Core
Message no. /MRSS/SGE034
Diagnosis
Resource 00000000010000000000000000000000 has not yet been created in MRS.
System Response
No assignments have been created for resource 00000000010000000000000000000000, even though, according to the organizational model, this resource is to be taken into consideration in the planning board.
Procedure
Contact technical support.
Procedure for System Administration
Create the resource in question in MRS."
I have run the Report
/MRSS/HCM_RPTWFMIF : Transfers the HR data (availability times, qualifications and the resources itself) into the MRS Basis
But even after that I am not getting the resources in the planning board.
Also I am not able to view the Demands from PM/CS orders.
I have created PM Orders and
Assigned Work centres to the operations and
assigned the Resources to the Operations.
The HR assignment to the work center is also done.
I have tried T Code /MRSS/PLBOSRV - Enter the MRS planning board using a specified order
to pull the order demand. But it is not working
Its giving following message
1004280 is not a valid demand
Message no. /MRSS/SGU139
Diagnosis
The order does not exist in MRS.
This may be because:
The order number has an invalid format.
The order does not exist.
The order is not relevant for planning and has therefore not been transferred to MRS.
The order has been deleted from MRS.
Pls help me on this.
Thanks in advance and warm regards
Purnendu
Hi Anil/Saurabh - Thanks a lot for your replies.
I have checked the MRS configuration as per your suggestion.
It looks fine as per the configuration guide. I have done the PM/CS integration for Orders as demand.
But the Demands are not visible on the Planning Board.
I have checked in the debugging mode what is causing the problem - It looks like
"The Database Table: /mrss/d_dem_h needs entry"
But there are no entries in this table.
I could not find any Customizing transactions or Application transactions for maintaining this table. This is an Application Table for Master and Transaction Data and its Display and Maintenance allowed with Restriction.
I could not also find any transaction for transferring Demand from ECC(R/3) to MRS.
How do I maintain entries in this table?
How do I transfer Demand from ECC to MRS?
Saurabh - I have also been not able to transfer HR Resources from ECC to MRS.
We don't have WFM Core installed in our instance. But MRS should work fine without WFM. MRS Basis should take care of it.
To transfer Employee resources i have run the Program " /MRSS/HCM_RPTWFMIF". But when I execute the transaction with the selection parameters system shows that it is processing (Clock at the bottom Status bar) but it does not shows any result or status.
So I am not sure whether it is executing the program properly.
Pls help me resolve these issues.
Thanks and warm regards
Purnendu
Similar Messages
-
Variables from workbook are not visible in the Planning function
Hi,
We're using a workbook with a bunch of queries in it. Every query has a lot of variables declared that are calculated based on two input ready variable that users are required to fill the first time.
Everything works as expected until the save data function is called, which in turn calls the planning function.
Here, the user exit variable try to be recalculated again. Unfortunately, this planning function loses track of the two input ready variables that were on the workbook, so the user exit variables have no values.
Can you please suggest a method so that:
a) The user exit processing in the planning function "sees" the two input ready variables
b) The user exit processing is not triggered in the planning function and it's taking the already calculated values
Let me know if you require further information.
Best regards,
GeorgeHi,
the variables in the filter of the query lives in one variable container and the variables of the filter of the planning sequence live in another variable container. They do not know each other. You need to establish a relationship between them. Usually this is done via variable binding for regular variables. For exit variables the variable binding can be done as written above.
If as in your case you have variables in the filter of the query and you want to use their values in the variable of the planning sequence than you need to store the values somewhere where you can retrieve them in the exit. This can be in a e.g. in shared memory or in the session memory. To do this you need to spend an extra exit variable in the filter of the query. The exit variable reads the real values and stores it somewhere (e.g. shared memory, global parameter of a function group, a class member or something similar). Now as the variable value is stored it can be read in the implemenation of the exit variable in the filter of the planning sequence.
In total we have 3 variables:
Variable 1 contains the value which the user keys in and exists in the filter of the query.
Variable 2 reads variable 1 and stores the value. It needs to be defined in the filter of the query as well.
Variable 3 reads the stored value and needs to be defined in the filter of the planning sequence.
Regards Matthias Nutt
SAP Consulting Switzerland -
After BI 7.0 Upgrade, Authorization Roles and profiles are not visible
Hi Gurus,
We have an issue with authorization roles and profiles are not visible for all end users with new Bex Analyzer (BI 7.0) tool. But still they can see these roles with old Bex Analyzer ( Bex 3.5) tool.
As a developer I have SAP_ALL acces and I can see all authorization roles in new BEx Analyzer (BI 7.0).
I verified in SU01 for user access and every are assigned there roles and they are green.
Do we need to add any new authorization object to fix this issue, please let me know
Thanks and appreciate your help.
Thanks
Ganesh Reddy.
Edited by: Ganesh Reddy on Oct 26, 2009 4:41 PMHi Ganesh,
check the behaviour, if you assign
S_USER_AGR
ACT_GROUP = "..name of the assigned role.."
ACTVT = 03 (for "display")
b.rgds,
Bernhard -
Images are not visible in the iPhone.
When I open iTunes there are number of images found in the iPhone, but the images are not visible in the iPhone actually.
I using local deployment. I deploy my application directly from NWDS to a Mobile Client running also locally in my machine. Maybe I'm wrong, but I think that Mobile Client look for resources in NWDS workspace.
This is the dpi file located in the Mobile Client inbox folder when I perform the deployment.
<?xml version="1.0" encoding="UTF-8"?>
<deployment>
<device>
<repository>
<mcd name="IrviaDemoApp" namespace="" version="1">
<action type="install"/>
<location type="local">
<source path="C:\Documents and Settings\oloranube\workspace.sr5.jdi\LocalDevelopment\DCs\company.es\irvia_demo_app\_comp\MOBILE-INF\MCD.xml" property="mcd" type="file"/>
<component name="hpcds.es~irvia_demo_app">
<applications>
<application deploy="true" name="IrviaDemoApp"/>
</applications>
<source path="C:\Documents and Settings\oloranube\workspace.sr5.jdi\LocalDevelopment\DCs\company.es\irvia_demo_app\_comp\bin" property="bin" type="dir"/>
<source path="C:\Documents and Settings\oloranube\workspace.sr5.jdi\LocalDevelopment\DCs\company.es\irvia_demo_app\_comp\gen_wdp" property="gen_wdp" type="dir"/>
<source path="C:\Documents and Settings\oloranube\workspace.sr5.jdi\LocalDevelopment\DCs\company.es\irvia_demo_app\_comp\src\mimes" property="mimes" type="dir"/>
<source path="C:\Documents and Settings\oloranube\workspace.sr5.jdi\LocalDevelopment\DCs\company.es\irvia_demo_app\_comp\gen_wdp\application-j2ee-engine.xml" property="j2ee_xml" type="file"/>
</component>
</location>
</mcd>
</repository>
</device>
</deployment>
There is a <source> entry for the mimes directory, where "Component images" are located.
PD: Sorry about my poor english. I hope you to understand me. -
Goods are not visible on the Web Shop main page (RUMP UP)
Hi colleagues.
Help please anybody :)
There was the problem with the goods in Web Shop.
Goods are not visible on the page Web Shop.
Below you can see actions performed by us and Prerequisites:
1. Repository was unachieved from Standard archive - WEC20_MDMCATALOG_CONS
2. Taxonomy, Hierarchy and Lookup table data were transferred from CRM via MDMGX
3. Manually created root node in Product Catalogs table in MDM
4. Put technical code (ID) of created node to Product Catalog module in WCEM configuration - field Catalog ID.
5. Fill another necessary fields in Product Catalog module in WCEM.
6. Manually add test record in MDM and linked to node in Product Catalog table, elements from Main Taxonomy and other required fields.
7. In preview mode of WCEM configuration not possible see any records from MDM (but product catalog elements showed correctly)
More information about settings in MDM, CRM,WCB and configuration steps can see in attachment files
Best regardn,
AndreyHi Denis
Leading zeroes it's no my case, because the products (materials) replicated from CRM to MDM.
Replication from CRM to MDM via MDMGX and Initial Load R3AC1 is successfull.
But on the WebChannel web shop page this products are not visible.
I have suggested that the problem in authirizations of technical user, which uses RFC Destinations from SAP NW AS Java (Web Channel) to MDM.
According Security Guide for SAP Web Channel 2.0 (paragr. 8.3.2 see please screenshot), user of WEC_MDM_DEFAULT destination must assign the role WEBCHANNEL_CATALOG_DISPLAY_ROLE.
But this role does not exist in the system (SAP MDM, SAP NW).
Please give me advice about this. -
TS1292 There are two numbers that are not visible in the middle of the code What can I do?
There are two digits that are not visible in the middle of the itune code. How can I still access this card?
Click here and request assistance, supplying as much of the code as you can.
(74408) -
Hi - I am looking for the Adobe Illustrator 2014 1.2 (or .0.2) bugfix update for Mac - and it is not visible in the Adobe Creative Cloud Packager (Mac version). The only update visible is Illustrator CC 2014.1 - which is what introduced the bugs.
The only thing that I can think of that might be causing the issues that I have a Mac Mini on Mavericks.
DaveHi
I have discovered that my question above is a non-question. A user triggered by looking at the below article about Illustrator 2014 cc 17.0.2
http://helpx.adobe.com/illustrator/release-note/illustrator-17-0-2-release-notes.html
He had recently upgraded from wht we now know is 18.0 to 18.1 which is the latest version. He read the above artic
le and supposed that it was a bug fix release for his version - because the v17 ov18 number is not often displayed. It is usually just 2014 CC.
I have asked him to post a bug report about Adobe Illustrator CC 2014.1
Dave -
Aperture ate my picture files and they are not recoverable. The guy at the Genius Bar told me to Trash the App, empty Trash, then go to Purchases and reinstall. But Purchases says it is "Installed" so it does not let me download it again. HELP!!!!
I typed Aperture into Spotlight and sure enough it did show up.
It looks like it is supposed to be in Apps.
But it is not there.
So I clicked on the spotlight Aperture and it opened up the App!!!!
But I do not know where it is to move it!
How can I find it?
While Aperture is running and you are seeing it in the Dock, ctrl-click (or right click) the Dock icon.
You will see a contextual menu. Click on "Options", then select "Show in Finder".
And check the "keep in Dock" mark, so you will not lose it from the Dock. -
Contacts and calendar are not syncing? the word info is not in the selection iTunes sync menu
contacts and calendar are not syncing? the word info is not in the selection iTunes sync menu
Hey jimneeds,
Thanks for the question. This feature was discontinued with OS X Mavericks:
iOS: Syncing your data with iTunes
http://support.apple.com/kb/HT1386
What you can sync
[…] - Contacts*
*To sync this content on an iOS device using OS X Mavericks v10.9 or later, use iCloud or another cloud-based service.
Thanks,
Matt M. -
my iWork (pages and keynote) are not communicating with the iCloud. I haven't changed anything and all of the sudden there is no sync happening. My iCloud account is fine as i can create documents on my iPad and they appear on iCloud. However, when i change documents on my mac (documents that are supposed to be in the iCloud), the changes do not sync with my other devices nor with iCloud. Even when i create new documents on my mac and save them to iCloud, all seems okay and i can access them from my mac, however they do not show up in the iCloud and i can't access them with my other devices.
Most recent version of mountain lion updated over a month ago. New iPad in use for over a month.
thanksThe same thing is happening to me, Mail was fine about an hour ago and now is rejecting correct password. Typical when today I'm waiting some important emails!
-
I have purchased items from CityVille and they are not available in the App although my card has been charged for the purchases. I also have an email receipt with the purchase. Can you please tell me how to resolve this issue?
iTunes Store: Hiding and unhiding purchases
http://support.apple.com/kb/HT4919 -
ratings and picks are not shown in the pictures in the filmstrip, although marked in the LR presets. Who can help?
found the solution: the filmstrip was to small !!!
-
Is it possible to save a Photoshop project with multiple tabs (inducing images) for later use. Now, when I close Photoshop, it ask to save each tab separately and they are not staying in the project for later usage. Thanks in advance for you help.
You should ask in Photoshop General Discussion
The Cloud forum is not about using individual programs
The Cloud forum is about the Cloud as a delivery & install process
If you will start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll -
Facebook profile and home are not visible
Today in the afternoon, Facebook started to act strangely. I can log on without a problem, but when i'm in the website the home and the profile pages are not visible, they are blank and this is strange because with Chrome i have no problems, and because in the safe mode the problem is still here, so the plugins aren't the source of the problem.
The account and other option pages are fine, only those two don't work.
Few weeks ago, i had to change a value in the about:config page, to make work "youtube buttons", but i think it's not that the problem, also because this morning Facebook worked. I don't know what to think. Is this maybe Facebook IT fault? Boh.
Thank you for your timeClear the cache and the cookies from sites that cause problems.
* "Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
* "Remove the Cookies" from sites causing problems: Tools > Options > Privacy > Cookies: "Show Cookies" -
Icons are not visible when the form is run
I develop a form with only a push button. I developed form using oracle 10DS. I have saved my form in application server. To see an icon in my button, i did the following things:
1. In application server i made a jar named test.jar. It consists of just two gif images.
2. I copied this jar in application server's \forms90\java directory
3. I configured formsweb.cfg file as the following.
4. my \form90\java\oracle\forms\registry\registry.dat is as the following.
whenever i run form i can not see icon but in client's oracle jar cache jar is downloaded.
-------------------------------formsweb.cfg -------------------------------------------
=========================
# $Id: formsweb.cfg,v 1.24 2003/08/22 01:07:35 pkuhn Exp $
# formsweb.cfg defines parameter values used by the FormsServlet (f90servlet)
# This section defines the Default settings. Any of them may be overridden in the
# following Named Configuration sections. If they are not overridden, then the
# values here will be used.
# The default settings comprise two types of parameters: System parameters,
# which cannot be overridden in the URL, and User Parameters, which can.
# Parameters which are not marked as System parameters are User parameters.
# SYSTEM PARAMETERS
# These have fixed names and give information required by the Forms
# Servlet in order to function. They cannot be specified in the URL query
# string. But they can be overriden in a named configuration (see below).
# Some parameters specify file names: if the full path is not given,
# they are assumed to be in the same directory as this file. If a path
# is given, then it should be a physical path, not a URL.
# USER PARAMETERS
# These match variables (e.g. %form%) in the baseHTML file. Their values
# may be overridden by specifying them in the URL query string
# (e.g. "http://myhost.mydomain.com/servlet/f90servlet?form=myform&width=700")
# or by overriding them in a specific, named configuration (see below)
[default]
# System parameter: default base HTML file
baseHTML=base.htm
# System parameter: base HTML file for use with JInitiator client
#baseHTMLjinitiator=basejini.htm
# System parameter: base HTML file for use with Sun's Java Plug-In
baseHTMLjpi=basejpi.htm
# System parameter: base HTML file for use with Microsoft Internet Explorer
# (when using the native JVM)
baseHTMLie=baseie.htm
# System parameter: delimiter for parameters in the base HTML files
HTMLdelimiter=%
# System parameter: working directory for Forms runtime processes
# WorkingDirectory defaults to <oracle_home>/forms90 if unset.
workingDirectory=
# System parameter: file setting environment variables for the Forms runtime
processes
envFile=default.env
# System parameter: JVM option for Microsoft Internet Explorer.
# This parameter specifies how to execute the Forms applet under
# Microsoft Internet Explorer 5.x or above. Put IE=native if you want
# the Forms applet to run in the browser's native JVM.
IE=JInitiator
# Forms runtime argument: whether to escape certain special characters
# in values extracted from the URL for other runtime arguments
escapeparams=true
# Forms runtime argument: which form module to run
form=test.fmx
# Forms runtime argument: database connection details
userid=
# Forms runtime argument: whether to run in debug mode
debug=no
# Forms runtime argument: host for debugging
host=
# Forms runtime argument: port for debugging
port=
# Other Forms runtime arguments: grouped together as one parameter.
# These settings support running and debugging a form from the Builder:
otherparams=buffer_records=%buffer% debug_messages=%debug_messages% array=%array%
obr=%obr% query_only=%query_only% quiet=%quiet% render=%render% record=%record%
tracegroup=%tracegroup% log=%log% term=%term%
# Sub argument for otherparams
buffer=no
# Sub argument for otherparams
debug_messages=no
# Sub argument for otherparams
array=no
# Sub argument for otherparams
obr=no
# Sub argument for otherparams
query_only=no
# Sub argument for otherparams
quiet=yes
# Sub argument for otherparams
render=no
# Sub argument for otherparams
record=
# Sub argument for otherparams
tracegroup=
# Sub argument for otherparams
log=
# Sub argument for otherparams
term=
# HTML page title
pageTitle=Oracle Application Server Forms Services
# HTML attributes for the BODY tag
HTMLbodyAttrs=
# HTML to add before the form
HTMLbeforeForm=
# HTML to add after the form
HTMLafterForm=
# Forms applet parameter: URL path to Forms ListenerServlet
serverURL=/forms90/l90servlet
# Forms applet parameter
codebase=/forms90/java
# Forms applet parameter
imageBase=codeBase
# Forms applet parameter
width=750
# Forms applet parameter
height=600
# Forms applet parameter
separateFrame=false
# Forms applet parameter
splashScreen=
# Forms applet parameter
background=
# Forms applet parameter
lookAndFeel=Oracle
# Forms applet parameter
colorScheme=teal
# Forms applet parameter
logo=
# Forms applet parameter
restrictedURLparams=HTMLbodyAttrs,HTMLbeforeForm,pageTitle,HTMLafterForm,log,allow
_debug,allowNewConnections
# Forms applet parameter
formsMessageListener=
# Forms applet parameter
recordFileName=
# Forms applet parameter
serverApp=default
# Forms applet archive setting for JInitiator
archive_jini=f90all_jinit.jar,classes12.jar,test.jar
# Forms applet archive setting for Microsoft Internet Explorer native JVM
archive_ie=f90all.cab
# Forms applet archive setting for other clients (Sun Java Plugin, Appletviewer,
etc)
archive=f90all.jar
# Number of times client should retry if a network failure occurs. You should
# only change this after reading the documentation.
networkRetries=0
# Page displayed to Netscape users to allow them to download Oracle JInitiator.
# Oracle JInitiator is used with Windows clients.
# If you create your own page, you should set this parameter to point to it.
jinit_download_page=/forms90/jinitiator/us/jinit_download.htm
# Parameter related to the version of JInitiator
jinit_classid=clsid:CAFECAFE-0013-0001-0017-ABCDEFABCDEF
# Parameter related to the version of JInitiator
jinit_exename=jinit.exe#Version=1,3,1,17
# Parameter related to the version of JInitiator
jinit_mimetype=application/x-jinit-applet;version=1.3.1.17
# Page displayed to users to allow them to download Sun's Java Plugin.
# Sun's Java Plugin is typically used for non-Windows clients.
# (NOTE: you should check this page and possibly change the settings)
jpi_download_page=http://java.sun.com/products/plugin/1.3/plugin-install.html
# Parameter related to the version of the Java Plugin
jpi_classid=clsid:8AD9C840-044E-11D1-B3E9-00805F499D93
# Parameter related to the version of the Java Plugin
jpi_codebase=http://java.sun.com/products/plugin/1.3/jinstall-13-win32.cab#Version
=1,3,0,0
# Parameter related to the version of the Java Plugin
jpi_mimetype=application/x-java-applet;version=1.3
# EM config parameter
# Set this to "1" to enable Enterprise Manager to track Forms processes
em_mode=0
# Single Sign-On OID configuration parameter
oid_formsid=formsApp_drsshl_C75ED7E7CA18492FA35AA090350527B7
# Single Sign-On OID configuration parameter
oracle_home=E:\Oracle_SHLAS
# Single Sign-On OID configuration parameter
formsid_group_dn=cn=Logical Application Group,
orclApplicationCommonName=formsApp_drsshl_C75ED7E7CA18492FA35AA090350527B7,
cn=forms, cn=Products, cn=OracleContext
# Single Sign-On OID configuration parameter: indicates whether we allow
# dynamic resource creation if the resource is not yet created in the OID.
ssoDynamicResourceCreate=true
# Single Sign-On parameter: URL to redirect to if ssoDynamicResourceCreate=false
ssoErrorUrl=
# Single Sign-On parameter: Cancel URL for the dynamic resource creation DAS page.
ssoCancelUrl=
# Single Sign-On parameter: indicates whether the url is protected in which
# case mod_osso will be given control for authentication or continue in
# the FormsServlet if not. It is false by default. Set it to true in an
# application-specific section to enable Single Sign-On for that application.
ssoMode=false
# The parameter allow_debug determines whether debugging is permitted.
# Administrators should set allow_debug to "true" if servlet
# debugging is required, or to provide access to the Forms Trace Xlate utility.
# Otherwise these activities will not be allowed (for security reasons).
allow_debug=false
# Parameter which determines whether new Forms sessions are allowed.
# This is also read by the Forms EM Overview page to show the
# current Forms status.
allowNewConnections=true
# Example Named Configuration Section
# Example 1: configuration to run forms in a separate browser window with
# "generic" look and feel (include "config=sepwin" in the URL)
# You may define your own specific, named configurations (sets of parameters)
# by adding special sections as illustrated in the following examples.
# Note that you need only specify the parameters you want to change. The
# default values (defined above) will be used for all other parameters.
# Use of a specific configuration can be requested by including the text
# "config=<your_config_name>" in the query string of the URL used to run
# a form. For example, to use the sepwin configuration, your could issue
# a URL like "http://myhost.mydomain.com/servlet/f90servlet?config=sepwin".
[sepwin]
separateFrame=True
lookandfeel=Generic
# Example Named Configuration Section
# Example 2: configuration affecting users of MicroSoft Internet Explorer 5.x.
# Forms applet will run under the browser's native JVM rather than using Oracle
JInitiator.
[ienative]
IE=native
# Example Named Configuration Section
# Example 3: configuration forcing use of the Java Plugin in all cases (even if
# the client browser is on Windows)
[jpi]
baseHTMLJInitiator=basejpi.htm
baseHTMLie=basejpi.htm
# Example Named Configuration Section
# Example 4: configuration running the Forms ListenerServlet in debug mode
# (debug messages will be written to the servlet engine's log file).
[debug]
serverURL=/forms90/l90servlet/debug
[test]
form=E:\ict\ITSUPPORT\test.fmx usesdi=yes
userid=support/s00001@dshl
width=100%
height=100%
colorscheme=blue
pageTitle=ICT Support :: Just in Time
imagebase=codebase
archive_jini=f90all_jinit.jar,rolloverbutton.jar,getclientinfo.jar,infobutton.jar,test.jar
webUtilArchive=frmwebutil.jar,jacob.jar
baseHTMLjinitiator=webutiljini.htm
#lookAndFeel=Oracle
splashscreen=ash.gif
logo=none
separateFrame=false
******************************************** registry.dat
---=========================
# This is the Registry file.
# This file contains the logical [Java] Class name and an associated
# [numerical] identifier that will be used to refer to objects of the
# class in order to reduce the amount of information that needs to be
# repeatedly transmitted to the client.
# This file is of the Form understood by java.util.Properties (for now)
# The System Level sound file is relative to the CODEBASE
oracle.classById.1=oracle.forms.engine.Runform
oracle.classById.4=oracle.forms.handler.FormWindow
oracle.classById.5=oracle.forms.handler.AlertDialog
oracle.classById.6=oracle.forms.handler.DisplayList
oracle.classById.7=oracle.forms.handler.LogonDialog
oracle.classById.8=oracle.forms.handler.DisplayErrorDialog
oracle.classById.9=oracle.forms.handler.ListValuesDialog
oracle.classById.10=oracle.forms.handler.EditorDialog
oracle.classById.11=oracle.forms.handler.HelpDialog
oracle.classById.12=oracle.forms.handler.FormStatusBar
oracle.classById.13=oracle.forms.handler.MenuInfo
# oracle.classById.14=UNUSED
oracle.classById.15=oracle.forms.handler.ApplicationTimer
oracle.classById.16=oracle.forms.handler.MenuParametersDialog
oracle.classById.17=oracle.forms.handler.PromptListItem
oracle.classById.18=oracle.forms.handler.CancelQueryDialog
oracle.classById.257=oracle.forms.handler.TextFieldItem
oracle.classById.258=oracle.forms.handler.TextAreaItem
oracle.classById.259=oracle.forms.handler.FormCanvas
oracle.classById.261=oracle.forms.handler.ButtonItem
oracle.classById.262=oracle.forms.handler.CheckboxItem
oracle.classById.263=oracle.forms.handler.PopListItem
oracle.classById.264=oracle.forms.handler.TListItem
oracle.classById.265=oracle.forms.handler.CfmVBX
oracle.classById.266=oracle.forms.handler.CfmOLE
oracle.classById.267=oracle.forms.handler.RadioButtonItem
oracle.classById.268=oracle.forms.handler.ImageItem
oracle.classById.269=oracle.forms.handler.IconicButtonItem
oracle.classById.270=oracle.forms.handler.BlockScroller
oracle.classById.271=oracle.forms.handler.JavaContainer
oracle.classById.272=oracle.forms.handler.TabControl
oracle.classById.273=oracle.forms.handler.ComboBoxItem
oracle.classById.274=oracle.forms.handler.TreeItem
oracle.classById.281=oracle.forms.handler.PopupHelpItem
# Defaults for the Font details, all names are Java Font names. Each of
# these parameters represents the default property to use when none is
# specified.
# defaultFontname represents the default Java fontName.
# defaultSize represents the default fontSize. Note that the size is
# multiplied by 100 (e.g. a 10pt font has a size of 1000).
# defaultStyle represents the default fontStyle, PLAIN or ITALIC.
# defaultWeight represents the default fontWeight, PLAIN or BOLD.
default.fontMap.defaultFontname=Dialog
default.fontMap.defaultSize=900
default.fontMap.defaultStyle=PLAIN
default.fontMap.defaultWeight=PLAIN
# Default Font Face mapping.
# appFontname represents a comma delimited list of Application Font Names.
# javaFontname represents a comma delimited list of Java Font Names.
# The number of entries in the appFontname list should match the number in
# the javaFontname list. The elements of the list are comma separated and
# all characters are taken literally, leading and trailing spaces are
# stripped from Face names.
# Note that this file uses the Java 1.1 Font names in order to be able to
# handle the NLS Plane (BUG #431051)
default.fontMap.appFontnames=Courier New,Courier,courier,System,Terminal,Fixed,Fixedsys,Times,Times New Roman,MS Sans Serif,Arial, Kunstler Script
default.fontMap.javaFontnames=MonoSpaced,MonoSpaced,MonoSpaced,Dialog,MonoSpaced,Dialog,Dialog,Serif,Serif,Dialog,SansSerif, Kunstler Script
# The Application Level icon files are relative to the DOCUMENTBASE
# example: icons/
# or an absolute URL.
# example: http://www.forms.net/~luser/d2k_project/
default.icons.iconpath=
default.icons.iconextension=gif
# Application level settings to control UI features
app.ui.lovButtons=true
app.ui.requiredFieldVA=false
# The background color is specified as an RGB triple.
app.ui.requiredFieldVABGColor=255,0,0
---====================================
I tried many times. But could not be successful. Then I just kept my icons in
\forms90\java directory without making jar. In my form, icon file name is the icon name without extension. Here, i can see my icon in button. but if i replace an icon
without changing the name of the icon, then i always see the old icon. The new icon, i can not see.
Please, help me with only Oracle 10g AS how i can see icon in button. Let's assume, there is not oracle 10g DS (any development tool) in the machine where the form is run.
Please, guide me clearly step by step so that i might be successful.
Thanks.
TKARIMThanks Bernard,
It works fine with JInitiator but not working with
the JPI. For JPI what settings I need to do ??hi TKARIM and Bernard, i am having similar problem even with the Bernard's recommended setup. could you post the webutiljini.htm (i presume you are using config=test) ?
i am actually using jinitiator 1.3.1.28 with Oracle HTTP Server of OAS 10gR2) calling Forms Server 6i (f60cgi). After setting up according to Bernard's recommended setup steps, the java console showed that it loaded the icon jar file when it could not read the form, but it skipped the loading of the icon jar file once it read and started the form. How do we specify in the form to pick up the icon from the jar file instead from a directory ? Or do we need to specify ? Any ideas ?
Thx and Regards
dkklau
Maybe you are looking for
-
I just downloaded an album but one song won't play instead a message that "This computer is not authorized" to play the song. The prompt has a log in and when I log in it tells me the computer is already authorized. What gives? Specifically the album
-
Hello team, I am facing issue with ISE after changing the domain name, new default certificate was generated and also the old cert is available, because of 2 group certs facing issue, any facing the same issue.
-
Attaching Text file and sending mail
Hi all, I am trying to attach a text file (ASCII file) and send using mail. I am not able to get proper data in attachement.Can anyone suggest me which type should i use to get the data in proper format. i was
-
How to compile kernel-eeepc with squash support?
What i have to change to this package from aur (kernel-eeepc - http://aur.archlinux.org/packages.php?ID=26392) for having aufs/squashfs support?
-
In new event window how do I change the auto settings?
As an example of this question, each new event window always has "all day event" checked, how do I change this to be automatically unchecked?