MS 6153 Internal USB Connector?
Hi all,
I have a MS 6153VA Mainboard (INTEL) with 2 USB onboard.
Now, I get a CDR-drive with additional Memory slots, running with USB
Unfortunally, there is no internal USB connector on the mainboard.
Does anyone has an idea, how to connect the drive to USB?
(n.b. the connector is not an USB, only in Motherboard-style.
Thanks in advance for help.
Regards
Quote
CDR-drive with additional Memory slots, running with USB
I dont understand.
Please be a bit more spefic!
Similar Messages
-
Question about internal Bluetooth connector on Tecra 8100?
Hello all.
I have a pt810e-13c52-sp notebook. Upgraded to 512MB by using 2 toshiba 256mb pc100 modules bought in ebay, upgraded to a PIII 850 also got in ebay, and upgraded to a bigger 40GB wdc wd400e hard disk, with much less noise than 12GB original one.
Messing with my computer i have found an internal "bluetooth" connector next to the internal one that belongs to the keyboard.
Why is this?? Is there any unreleased Bluetooth module for Toshiba Tecra 8100??Hi Toka
Maybe I am wrong but I have found info that Tecra 8100 has no BT and this model can not be upgraded with BT module. Usually BT will be used just sometimes and if you need BT you can use USB BT stick. It is pretty easy to configure it and this small part can be used whenever you need it. -
I am looking for an internal usb port on the MAC pro motherboard. seems the Express 34/54 card requires a usb connection in addition to placing the card in one of the PCIe slots. The card manufacturer refers to the USB internal connection as an internal header. Not sure what this means but it would be nice to have an Express 34 PCIe card in the machine---using it with the new Sony SXS video cards.
any idea if the MB has one of these connections?thanks for the info. as I explained, I was trying to install an Express 34/54 reader card into one of the PCIe slots on a Mac Intel. There are cards out there, but they come with an additional usb cable that you must connect from the card (mini-usb connector) to the mother board (a female 5-pin connector--single row).
another solution is to buy the external sony device for $220. (Express 34/54 to USB2) which is an external housing enclosing the same card with a supplied AC adapter. This format will be a major format in the future for shooting video, so I hope someone develops a cheaper solution.
thanks for the help -
Dear HP forum members,
Where can we get the "HP USB Cable Kit"? (HP Gen8 FIO Internal USB Kit -- 662961-B21)
I have a problem with our HP DL320e Gen8 V2 servers. We use a few maschines as cluster nodes for a specialized SW which only works (without hacks) if booted from a vendor provided USB stick.
I would like to move these sticks inside the casing, there is also a connector on the mother board labeled as "internal usb" (J9), but i can not find any local dealer able to provide me these calbe kits... as it is a FIO option.
Is there a way how to buy them separatly for our preconfigured (726043-425) models?
Thank you.Hi:
You may also want to post your question on the HP Business Support Forum -- DL Servers section.
http://h30499.www3.hp.com/t5/ProLiant-Servers-ML-DL-SL/bd-p/itrc-264#.UyIDBP1OXGg -
Has anyone ever experienced the situation where plugging in the USB connector to the charging source (high-power USB port or Apple charger) halfway, then pressing it in firmly, results in the iPad not charging?
It's highly likely that there is a poor connection in the phone - either a pin in the dock connector or internal wiring harness. No software fixes or "tricks" would work, but I would recommend restoring in iTunes, first using a backup and if needed restore as a new phone.
Otherwise, opening and repairing the phone takes some tech knowledge that can't be relayed here. Apple doesn't repair phones other than replacing batteries (not inconceivable that you have a bad battery), but offers "out-of-warranty" replacement (refurb) phones for $149 (US). 3rd party iPhone repair centers may be able to fix it for less. Google to find them,
Tried soft and hard resets
FYI, there's no such thing as "soft" or "hard" resets in iPhone terminology. There is only one phone reset. You'll see those terms thrown around by technically ignorant posters, but they mean different things to different people and are actually archaic, 1980s PC terms that have nothing to do with iPhones.
See the User Guide, Appendix B. -
hi can any one help i want to get the new ipad for work but i need to print.i see i can buy a usb connector can i print if i plug my printer into the usb.
If you have a USB printer connected to your computer, Mac or PC, you can activate or install AirPrint and print from your iPad over wifi without any special apps.
Activate AirPrint in Mac OS X;
http://netputing.com/airprintactivator/
Add AirPrint to Windows;
http://jaxov.com/2010/11/how-to-enable-airprint-service-on-windows/ -
K7T Turbo D-Bracket USB connector?
Please I need some help.
I have a K7T Turbo Limited Edition Motherboard 6330 V.30 . It came with the P2P USB Bracket and the D-Bracket.
I can only find one place on the motherboard for a USB connector, how am I supposed to install these? Is there a mismarked motherboard pinout?
My Motherboard manual says it has a connectors for 6 USB ports.
I have 2 near the PS2 connectors built in, the D-Bracket has 2, the P2P has 2 which = 6, but I can't find a place to plug the brackets into the motherboard.
I would appreciate any help in the matter at all
NeoghostHi
According to the MSI site for the K7T Turbo Limited Edition, your motherboard only supports 4 USB connections.
You can use a USB PCI card to obtain more if needed.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=25 -
Apple USB keyboard does not work with one internal usb port
Hi everyone,
hope someone can help me to solve my problem. I have a MPB13 retina late 2013 since something like 3 months. I have additional screen (dell), usb wired keyboard (apple) and BT magic mouse.
Since a few days, my usb keyboard does not work well. It only want to work properly when plugged to the rights side usb port internal port and not anymore on the left one. It also work on a usb external concentrator. Before, I had no problem, it worked perfectly. There was no problem such as cofee on it...
After searching the web on such problem, I tries a few things such as:
I tried the keyboard on another computer (windows): works fine
I tried usb stick and external DVD reading on the left internal usb ports: works fine
I switch the MPB off and turn it back on: the usb keyboard still does not work on the left usb port
I tried the SMC and PRAM reset : nothing
Any idea ??
Thanks
GuillaumeI'm facing the same problem, found any solutions ?
-
is there a driver to let a ps2 keyboard plugged in with a usb connector work on my macbook pro 13inch?
I know there are more threads about this subject but none was really an answer.
I got a keyboard (brand medion) with a ps2 connector. i wanted it to connect to my macbook so i bought an ps2 to usb connecter.
wile connected with my macbook the keyboard leds flash one time like they do when you put it in a ps2. but after this just doesn' t work
I think i might miss a driver or its just turned of somwhere in the system. an previous answer was said something about a safe reboot and a lot of codes but thats to hard for me.
so any good solutions????I've never found a PS2 to USB adapter that worked, or IIRC I've never found one at all. I have USB TO PS2 but not the other way. Just go out and buy a new keyboard. PS2 is so late 90s/early 2000s
-
How to connect my Iridium 9555 to a USB connector on the Mac OS 10.7.3?
How to connect my Iridium 9555 to a USB connector on the Mac OS 10.7.3?
i can not create a new network configuration via USB interface on 10.7.3.Doesn't look like they've updated their driver in a while. October 15 - 2010.
Typically old drivers and 10.7 don't get along so well. Short answer, unless you know how to write a driver, you might be outa luck.
Call their support line and see what they say.
-G -
I have a mid-2010 polycarbonate/white MacBook (model A1342) running OS X 10.6.8. My machine has been having issues with the internal Bluetooth and keyboard/trackpad randomly ceasing to function.
Bluetooth issue
As of recently (the past month or two), the Bluetooth adapter will completely disappear and eventually reappear on a random basis. It won't appear at all in System Profiler, and the BT menu says "not available". Also, I have had a few kernel panics recently, all of which were apparently thrown by a Bluetooth process/daemon/driver (unfortunately I forgot which one, and also lost the logs from the panics.)
My system has a Broadcom Bluetooth chip that's part of the AirPort card, but is basically just an internal USB device. The adapter has some sort of integrated USB hub ("BRCM2070 Hub"), which the "Bluetooth Module" device itself is connected to.
Nonetheless, this seems to be some sort of problem on the USB bus. Whenever there is a failure, I will almost always see output in Console showing USB errors (ie errors about "enumerating a USB device", "clearing port power", "setting port power", "getting port status", etc). It will either be on any of the ports of the hub at 0x6600000 (the "BRCM2070 Hub" that "Bluetooth Module" is connected to), or port 6 of the hub at 0x6000000 (BRCM2070's port on the internal bus, which the keyboard/trackpad is also connected to on port 3).
I can post more/longer ones, but here's a somewhat short example of the error messages I might receive:
11/18/12 3:18:36 PM kernel USBF: 7351.492 [0xcf9b300] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 6 of Hub at 0x6000000)
11/18/12 3:18:38 PM kernel USBF: 7353.987 AppleUSBHubPort[0xcf9b300]::FatalError - Port 6 of Hub at 0x6000000 reported error 0xe00002c7 while doing clearing port power feature
11/18/12 3:18:38 PM kernel USBF: 7353.987 [0xcf9b300] The IOUSBFamily was not able to enumerate a device.
11/18/12 3:20:20 PM blued[448] Apple Bluetooth daemon started
11/18/12 3:20:20 PM kernel USBF: 7456.186 [0x11fb1300] The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 2 of Hub at 0x6600000)
11/18/12 3:20:20 PM kernel USBF: 7456.188 [0x11fb1300] The IOUSBFamily was not able to enumerate a device.
Keyboard/trackpad issue
There's also an issue where the internal keyboard/trackpad will randomly cease functioning (until I restart), often a couple of times a day as of recently. I've had this issue on rare occasion for a while now, but it's gotten more frequent. And more recently, the caps lock light on the keyboard occasionally turns itself on when I'm away.
Both the internal keyboard/trackpad as well as the Bluetooth "hub"/device are connected to the same USB bus/hub. When the keyboard/trackpad die, I've noticed that there will be very similar messages in Console to those above and usually a Bluetooth failure at the same time. (In some cases, it seems to notice that the keyboard/trackpad isn't responding, then attempts to reset/reinitialize it...ie log below.) What could the root cause be...could it be the USB "root" hub/bus causing one or both of these to fail, or possibly a problematic device causing the other to lose connection? I haven't had issues with USB devices on other buses failing, though (ie no problems with external devices.)
Maybe more out of curiosity than anything else, but I've been poking around for info on what might be going on with the USB (aside from the 0x66 hub repeatedly dropping/reconnecting and etc), but can't find much. There seems to be no documentation about the error codes (ie 0xe00002c7) that the hardware/OS are relaying. I even poked through the source for some of the relevant kexts and some reading on OS X driver/kernel programming too...might as well learn more about the inner workings of OS X
Here's an example of some of the messages that I get about the Keyboard/Trackpad:
11/21/12 2:57:22 AM kernel USBF: 1439.228 IOUSBHIDDriver(AppleUSBMultitouchDriver)[0xd1ff000]: Detected an kIONotResponding error but still connected. Resetting port
11/21/12 2:57:22 AM kernel USBF: 1439.234 AppleUSBHubPort[0xd040600]::Resetting device Apple Internal Keyboard / Trackpad: port 3 of Hub at 0x6000000
11/21/12 2:57:22 AM kernel USBF: 1439.319 [0x14452600] USB HID Interface #0 of device CompositeDevice @ 5 (0x6610000)
11/21/12 2:57:22 AM kernel AppleUSBMultitouchDriver::message - kIOUSBMessagePortHasBeenReset.
11/21/12 2:57:23 AM blued[248] Apple Bluetooth daemon started
11/21/12 2:57:23 AM kernel AppleUSBMultitouchDriver::checkStatus - received Status Packet, Payload 2: device was reinitialized
Attempted fixes
Unfortunately, my Macbook isn't under warranty so I'm mostly on my own. First I zapped PRAM, reset SMC, ensured OS updates are installed (still on 10.6.8), and threw out a few drivers/software that were possible troublemakers. Next, I tried running another OS/install to rule out software issues. Accordingly, I found that the BT adapter sometimes disappears on Windows 7 as well (just did a clean install). And finally, I bought a new AirPort/BT card and installed it the other day. That seemed better at first, but I still have the problem of intermittent Bluetooth and keyboard/trackpad.
Problems/solutions?
What might the issue be, or is there anything that may be worth trying? As I mentioned, I've reset PRAM and SMC, made sure it's not an OS/driver issue (it happens on Win7 too), and replaced the Airport card. The machine does have aftermarket RAM (from OWC, ~2 years old) and SSD (Crucial M4, installed September)...but it seems unlikely that either of these would cause the problem. There haven't been any accidents that would have caused physical or (to my knowledge) electrical damage to it.
I also searched for any occurrences of similar problems, but could not find any that were applicable to the Macbook revision in question. There was a similar keyboard/trackpad issue on older Macbook Pros that was caused by stress on a ribbon cable...but that seems unlikely given the concurrent issues with Bluetooth as well as the different design.
The only thing I can think of next is to possibly replace the cable connecting the Airport card to the logic board, and possibly look at replacing the keyboard/trackpad (topcase). Anyway, I'm worried that it might be a hardware issue with the internal USB controller/hub, which would probably mean that it's unfixable unless I replace the logic board.
Any advice as to which of these might be a potential solution or cause of the problem? Or might I just as well sell it off in its current condition and replace it?
Thanks all!Has anyone find a fix for this? I've been using my Dragon Dictate headset on my MacBook Pro for about a year, and then today, when I plugged it in, I got this:
4/16/14 10:01:04.000 AM kernel[0]: USBF: 47.766 The IOUSBFamily is having trouble enumerating a USB device that has been plugged in. It will keep retrying. (Port 1 of Hub at 0x4000000)
4/16/14 10:01:07.000 AM kernel[0]: USBF: 50.269 AppleUSBHubPort::FatalError - Port 1 of Hub at 0x4000000 reported error 0xe00002c7 while doing clearing port power feature
4/16/14 10:01:07.000 AM kernel[0]: USBF: 50.269 The IOUSBFamily was not able to enumerate a device.
Here is what I have tried so far:
Reset the PRAM
Reset SMC
Verify disk (there were no problems)
Repair permissions
Boot with an external USB hard drive (which works fine on the "problem" computer) that contained an old SuperDuper clone of my hard drive from several months ago. I received the same "The IOUSBFamily was not able to enumerate a device" error when I plug in the headset.
Tried to headset on another computer, and it worked fine.
Plug in an external USB keyboard into the problem computer, and it works fine.
All of this would lead me to conclude that it is a hardware problem. But it seems that if it were a hardware problem, the external USB keyboard and external USB hard drive would not work (which they do). If the problem were with the headset, it wouldn't work on another computer, but it does. So I'm wondering if it's some sort of firmware issue…??????? URG!!!!!! -
MacBook Pro (mid-2010) Internal USB HUB freezes/locks up
MacBook Pro (mid-2010) wilth the latest firmware, etc.
OS X 10.9.1
USB KVM to share keyboard and mouse with another computer
This has been working flawlessly until I upgraded to 10.9.1
The KVM uses the Scroll Lock key to toggle the input between the two computers
I switch back and forth many times a day.
Almost once a day now, all my input to my MBP will lock up when switching the KVM over.
The MBP track pad, keyboard, blue tooth Magic Mouse, KVM mouse and keyboard all become unresponsive.
I am assuming that the interal keyboard/track pad/blue tooth transceiver are all tied to an internal USB HUB.
The MBP is up and running and I can ssh into it. The only error message in the log is that the mouse device coming from the KVM is busy and it will be disabled. I have tried to close the lid for several minutes and then re-open, but it does not resolve the issue. I have tried connecting another USB mouse/keyboard during this time and it will not work. I have tried kill -HUP on the usbd and USBAgent processes. Everything stays unresponsive. The only way to resolve this condition is to reboot the MBP. Note: the KVM works find on the other computer when I switch it back and forth regardless of the state of the MBP.
I am suspecting that when this happens it is some how disabling the internal USB HUB, which if all the other devices are connected through it, nothing no longer works (but maybe I am crazy with that thought). Anyone have any insight? Is there a way to reset the internal HUB short of a reboot?
Thanks in advance!I'm seeing the same problem with a 2010 Mac Mini with IOGear KVM and MS wireless mouse. This setup worked flawlessly for years on Snow Leopard but started hanging soon after the Mavericks upgrade. I'm running 10.9.4, currently the latest release. The system usually hangs after a KVM keyboard switch from Windows on the other set of KVM cables back to the Mac Mini. ssh into OSX works fine but a shutdown hangs indefinitely. top showed no processes spinning. The 1st console message after the hang was:
8/6/14 8:49:21.000 PM kernel[0] USBF: 1317978.201 AppleUSBHubPort: Port 2 of Hub at 0x6200000 about to terminate a busy device (Microsoft® 2.4GHz Transceiver v7.0) after waiting 10 seconds
There were no other messages for hours before this. I'm using VM Fusion but I think it hung once without it running. The Windows 7 side of the KVM works fine. -
i bought the iPad and got it home and when I turned it on, all I see is the iTunes logo w/ a usb connector and arrow. How do I clear that and go to the home screen??? HELP!
You need to Set Up the iPad... Connect it to iTunes...
See here for Getting Started...
http://www.apple.com/support/ipad/
and here...
iPad User Guide iOS 5
http://manuals.info.apple.com/en_US/ipad_user_guide.pdf -
My iPhone 4S went into lockup with a screen displaying an image of the USB connector pointing to the iTunes logo. I was traveling and took the phone to the closest Verizon store. The store informed me that I had a brick lock and that only an Apple retail store could unlock the phone. The Verizon store explained that they have seen this problem with SEVERAL other 4S users who had upgraded to the new iOS7 operating system and that to their knowledge it is too demanding to work on pre-iPhone 5S phones having a far less capable processor. The closest Apple store was 50 miles away in King of Prussia, Pennsylvania. I went to that store three days later (today) to reset the phone before flying out of Philadelphia Intl. Airport. The Apple store personnel were overloaded and not sensitive to my plight. They told me that I would have to make a reservation for a time 2 hours later for tech support. I couldn't do that without missing my flight - out of luck until I get back to Los Angeles. If the Verizon store explanation is true, Apple needs to accommodate 4S and earlier generation users and not force them to upgrade to a $459 iPhone 5S!
villebard wrote:
The Verizon store explained that they have seen this problem with SEVERAL other 4S users who had upgraded to the new iOS7 operating system and that to their knowledge it is too demanding to work on pre-iPhone 5S phones having a far less capable processor. !
The salesperson at Verizon has no clue what their saying.
My 4S and many of my friends works perfectly fine on IOS 7.3, no issue as all. -
I have just purchased an iphone today and it is coming up with a picture on the screen of the usb connector and itunes symbol. It also says that I now have no service and can only make emergency calls
Just a thought, but maybe consider returning the device. Seems it might be a bit too complicated for you.
Maybe you are looking for
-
What the difference and use between of TABLES and SY-REPID?
Hi, Experts, I have came accross 2 cases that i can't able understand EX1: TABLES: VBAP - >( Here also Appplication Server(AS) creates Wrokarea of Structure VBAP but, by data: v_vbeln like vbap-vbeln. double clicking on variable v_vbeln AS taki
-
STB not responding to FIOS TV Central
Hi all, Sorry if this is dupeage but I did a quick search and didn't find anything. I just installed a new DVR which replaced a SD STB. I've actived remote DVR pn the box and FIOS TV central sees it but says that it is not resonding. I am unable to a
-
I just downloaded Adobe Acrobat XI Pro, I am in the install process now and I am getting an Error message, Error 1303, stating I need to log on as an administrator ... this is my computer so I don't understand the issue??
-
Header table to repeat on every page
Hi, I have requirement and might be a common one. I have to built an rtf template for Purchase orders to output in pdf.I have a header table and detail table in the template. If there are more detail records the detail table get extended to next
-
I have a Cd with images that I need to open. It is published by Carestream health inc. any ideas what I can do ? thanks maxmax