Ms-6330 (k7t turbo2) dead board!

Please I need help with this...
I was installing a new cpu cooler, when accidentally hit a small resistor near the cpu. The resistor came to be the R639.
The board does not post and the D-bracket show all the leds in red!.
The resistor is not completely destroyed, it remains about half of it, giving a resistance of 1kohm.
I need to know if someone has a damaged board of the same type, the idea is to replace the bad resistance with a new one with the same value.
Has someone repaired boards this way?
Any advices well received.

Give the board to a good radio repair shop and ask them to replace the resistor.

Similar Messages

MS-6330 K7T Pro Dead board - help??

My PC just seems to have died, and now all four motherboard Diag lights are RED when I apply power to the PC. Nothing is displayed on the monitor, it just simply won't boot at all!!
I've check the power supply & that seems to be working okay.
Looking at some of the other posts for this model of board, I see the voltage regulator could be a problem. I've checked my board and this is not hot when I leave the power on for a few minutes, so I don't think this is the problem.
Any suggestions on what to try would be appreciated?

No all was working fine before. I'd had a couple (2 or 3) of problems the day before where it just locked up, but it rebooted fine, until the final time! The machine has usually been on all day, most days over the last twelve months or so without any major problems.
I had already cleaned everything before posting. I'd also had the processor out, powered up without it in place (as I'd read this in one of the earlier posts as something to try), then refitted it (with the heatsink) and tried repowering, still without sucess, hence the post here.
Any further ideas/suggestions please??

Installing XP Pro on MS-6330 (k7t turbo2)

Im having oodles of problems installing Xp pro (and even win 98) on my computer. My current setup is:
K7T Turbo2 (latest revision, with 3.5 bios)
Athlon XP 2000+
40 gig maxtor hd
hercules gamesurround fortissimo 2
Visiontek Geforce 4 MX 420 AGP
10x dvd rom
12x8x32 cd-rw
intellimouse optical (in ps2 mode atm)
standard keyboard
generic 512 pc 133 sdram (tested with various memory test, including mem86 or whatever that was called, hehe) no errors, works perfectly
Problems arise when installing xp pro (and xp home) when at the point where it says: starting windows ... then either it reboots, blue screens, with errors like: page fault in non page area, or usb.sys or something, so ive disabled usb, etc etc...
I already tried swapping out everrything from video to sound, etc, those tricks DO NOT WORK. Already tried using various settings in the bios, already tried mem timings, setting agp to 4x, or 2x, auto, manual and EA, etc... nothing seems work...
The only thing that DOES work, is disabling the internal cpu cache..why? BEATS ME?!? After its done loading hte main stuff, Im going to reinable it and see how it goes.. im tired of problems, I like the mobo, but Was having problems from the get go installing xp.. im reinstalling it now, since i was getting errors like irq_not less, that thingy there, and then stuff like ntfs error on a bsod, etc. Installed the 4 in 1's, 442's then 443's, didnt work...psu isnt really an issue, has 220 tco, and runs fine, hard drive is not damaged, neither are the other optical drivers, and im just at my wits end.. this is really starting to tick me off..
emailed msi tech support, nothing back yet... can someone PLEAES HELP!?!? What bios settings should i use for xp pro installs and stuff?? lemme know! Thanks!!! And should i REALLY reinstall service pack 1? any thoughts on this??

WEll shite, now i gotta kill 98, cause now IT aint even working...... this board sucks! Im having more problems than a ECS mobo on a good day.
Now what, ive stuck my voodoo 3 in, and im fudgin with the settings, but quite frankly, im sick of all this, if it dont work, its going back and that pc shop is gonna fix this
and heres that farking problem with xp now..
IRQL_NOT_LESS_OR_EQUAL
!?! AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAH!
*hair goes blonde, and turns super geek 5*

K7T Turbo2 On Board Sound - Need MIDI drivers

While setting up my first MIDI keyboard accompanied with software I run into this error message:
No MIDI input devices. Instal MIDI input drivers.
I was told to instal them using the Drivers Applet in the Control Panel but I can not find such an Applet.
Brandon

Ah.........
This is very confusing.
I don't understand how an Nvidia driver works with a Realtek chip but I will give it a try. Since we have same board and you are using the driver yourself I can't dispute that it should work. The only thing that leaves me suspicious is the fact that the sound drivers (4.42) that come with 5.10 drivers did not work at all. No sound period.
Also, I want to make sure I get rid of the Realtek drivers and software completely.
#1 I go to add/remove programs and select remove Realtek drivers
#2 I run Drivercleaner and select Realtek and hit start
After I do this though, I can go to Windows directory and there is still a ton of those Realtek "crab looking" files all over the place. I have looked in the start menu for a Realtek entry so I can see if they have included an uninstaller but no joy. I cna not find a directory entry for Realtek anywhere. It seems they just reside in the Windows folder all mixed in with the rest of the Windows files.
Am I being too anal..........?? Is removing through add/remove programs and the Drivercleaner good enough??
I am obsessive/compulsive enough to just wipe the HDD out with 1's & 0's and re-install Windows and then all the drivers again but I got my disk a couple years ago with the barebones I ordered from a re-seller and now Microsoft makes me call everytime to validate which is a huge pain in the ass. Cause I am a quick trigger on the reformat if I muck something up.

MOVED: USB2 & K7T Turbo2 M/board

This topic has been moved to Retired motherboards.
https://forum-en.msi.com/index.php?topic=98729.0

Quote
The motherboard has USB2 printed up it about 3 inches up from the pins where you connect the case lights/reset buttons etc.
printed next to the USB pin header? you'll probably find there's another header somewhere further up, that has 'USB1' next to it...
Quote
How do I check my bios settings for usb2 enabled?
it would normally be found in your 'Integrated Peripherals' > 'Onboard Devices' menu

K7T Turbo2 won't boot

ok, here goes I have a MS-6330 K7T Turbo2 mobo, 256m RAM 20G Western Dig HDD NVidia GEForceMX420 64mg vid card AMD Duron 900Mhz proc. I started and it won't post, fans spin but nothing else. Cleared CMOS and it'll boot, but not RE-boot without clearing the CMOS again. I've checked the mobo to make sure it not grounding out. tried taking everything else off the mobo and it still won't post. I've taken the battery out for 10 mins, and checked it..shows good on Multimeter. I tried flashing the Bios to v3.6..no change, wouldn't post so, now I'm back to the original v3.3 because if I want to USE my computer, I first have to clear the CMOS, load defaults and then it'll boot up fine. if I've missed something PLEASE fill me in...this thing has got me COMPLETLEY stumped. If it's the motherboard I'll just buy another one rather than go through the hassle of trying to prove it's still under warranty. Help me out fellas!! PLEASE!! ?(

wow....... this is a mirror image of what happened to me almost.... to put it blunty... sounds like mobo is dying... or the cpu is dying.... but ....
did u just build this computer or did this just start up recently??? the mobo has some serious issue of POSTing when it's first installed and i have absolutely no idea why..
also... check your hsf on your cpu and c if it's it mounted properly. another thing.. r u changing anything in the bios???
Ed.
P.S. yes.. don't bother to rma. it'll take u about a month and a half to 2 months rma'ing.. i currently hate msi for how they handle my rma...

K7T TURBO2 Cooks XP 1800+

My friend recently purchased a MSI MS-6330 K7T TURBO2 SOCKETA KT133A mobo and a XP 1800+ CPU to upgrade his old PIII. Along with the mobo and cpu he also got a volcano 9 cpu cooler and a enermax 350W ps.
When it booted up for the first time it appeared to run fine, windows booted up no problem but as we quickly noticed the FSB was set to 100mhz so it was only running @1150mhz so we shut it down and pulled the jumper to change it to 133FSB. When we booted it back up the it said it was a 1800+ and before windows could boot up the screen went black. Some how the cpu got cooked, the bottom of it was all black. So we installed my Duron 800 and it ran fine. what I'd like to know is if it was a faulty cpu or if the mobo could of caused it? it seems like it happened when we changed the FSB

YEAH!! my Pc run fine for the past 2 days..Can be run at 2000+ and installed windows.But after two days, my com fail to boot up, even boot up at 100mhz fsb.My com fail to boot after i shut down my Pc. Only the heatsink fan is running...I already try to clear the cmos...remove the battery..still no joy..:'(
ANYBODY PLZ HELP A9AIN!!!SERIOUS PROBLEM HERE!!!

K7T Pro2-A MS-6330, Dead board?

Hi, I've looked at all the other posts about this board and I think it's either a power supply problem, leaky capacitors, or just plain 'ol dead board.
The DLEDs stop on a random problem (it changes around every time) after the 1st boot after the system has been off for about 20mins or so. If I turn it off and boot again right away it's always 4 red LEDs the next time, and successive times. But if I wait for 20 mins or so and try it will be another random LED stop, although it hasn't ever gotten past video card initialization.
I have a couple of capacitors that are slightly bulgy at the top, but nothing leaking (checked the back of the board too). In the past I have noted a chemically burning smell every once in a while, not very often.
So should I replace the power supply, fix capacitors, replace the board?
thanks for any help, dave

they suffer from a dodgey voltage regulator as well so its not worth it on them

K7T Turbo2 MS-6330 Will not boot up

Can someone help, I have a K7T Turbo2 MS-6330, and it will not boot up, I know I have power to my MB, becasue when I plug it in, the lights on my DIMM chips light up, and my fan spins for about 1/2 second. I don't know what to check next. Any assistance would be appreciated.
THANKS...

First of all, write what hardware other than mobo you have: cpu, power supply, graphics, memory, etc.
also, read troubleshooting guide:
http://www.msi.com.tw/program/service/forum/index.php?threadid=1131&boardid=13&styleid=1
Take care

K7T Turbo2(MS-6330 V5) AGP Features FAQ

Hi! I'm using K7T Turbo2(MS-6330 Ver5.0) motherboard and just bought an MSI Geforce4 MX440 64MB DDR (MS-8878 SE).
When I run some benchmarking program (eg. 3D Mark 2001), the status of sideband addressing (SBA) and fastwrite (FW) of both the card and motherboard are shown as follow:
Graphics Card:
SBA: not supported
FW: supported but not enabled
Motherboard:
SBA: supported but not enabled
FW: not supported
I tried very hard to force the SBA features using variety of software (Rivatuner, PowerStrip), but all failed.
Experts here, do you think it is possible to force on either (or both) features? I heard that there are ways to force the features in low-level.
Helps & Advices pls!
TQ!

Hi,
From MSI,
Enabling SBA & FW didnt really add much to the performance. There might be potential compatibility & stability issue when enabling SBA & FW. So we will not let be enabled
After more clarification, this explanation is for both motherboard and display card of yours!

MSI K7T turbo2 MS-6330 bios ver 3.6..NEED SERIOUS HELP!!

Anybody plz help me.I own a mobo above running amd athlon xp 2000+. My system run well for one week. After dat, my system started to give me problem. It hangs one day and when i reboot my com, the message "Windows protection error. Please restart your computer" appears. I tried already many times to restarted my com..but still fails. So i think maybe RAM problem..so i try to remove and reinstall the RAM. Then my com succeed to boot into windows. Everything run ok..no problem for few days. Then suddenly my com hang again and I juz reboot my com. Then the same message appears again..May i know wat happened to my com.PLEASE HELP ME...:'(
My spec:
msi K7T turbo2 MS-6330 bios ver 3.6
AMD athlon xp 2000+
Asus v7100 Geforce 2 MX400
2x256 kingston ram(pc133)
2x20g maxtor hdd
1xTV tuner card
1XSb live soundcard

Try uninstalling the sound card and any other nonessential components. Also, when you uninstall click on the "show hidden" items and remove duplicates. Don't remove anything that you do not know exactly what it is including any marked "unknown" but if you see multiple sound cards or cd-roms, etc. remove them. Then see if you boot ok and gradually reinstall items.

Are the K7T Turbo2 and MS-6330 V5 the same MoBo

Please some one help!!!!!!!!!!!!!!!
I have a motherboard and on the motherboard the text say MS-6330 V5 and all i can find on msi homepage is a K7T Turbo2 MS-6330 v5 so is my mobo a k7t turbo2 ???????
i am lost............ ?(
i flashed my bios at my own risk with the newest bios for k7t turbo2 and it works well as hell so my thought is that my ms-6330 v5 really are a k7t turbo2 am i right ??

Hmm, I think 'MS-6330 V5' is the same as 'MS-6330 v5'... :D
So go on and buy your new cpu.

K7T Turbo2 MS-6330

I can't run amd xp2100 at 133 MHz with motherboard K7T Turbo2, but it works (not well) at 100 MHZ and the bios tells me that i have a AMD xp1500. I have another computer with the same motherboard but with amd xp2000 and it works well at 133 MHz. So I'm very confused !!!! a new bios version maybe? to solve this?

check cooler as this is most likley reason
is psu in one that works a better one,swap them over
use a lower vga card if a gf4 will help see if power is the issue
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=24%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20&NAME=MS-6330%20Ver5.0
bios needs to be 3.5 to be safe as thats when 2200 support added not clear were 2100 fits in

K7T Turbo2 (MS-6330) Booting problems

Last night, I installed an Athlon XP 1700+ on my K7T Turbo2 mobo. I can not boot into Windows now. Windows XP will hang on loading up mup.sys, and 98 resets at an indeterminate time. I cannot install Windows 98 or XP either, as both hang on the setup (Before I can even access recovery mode for XP). I've swapped out all my PCI devices, disabled nearly everything in the BIOS, etc... nothing good. Heres what I've got.
Athlon XP 1700+
K7T Turbo2 Mobo
ATI Radeon 9000 128mb
ATI Radeon 7200 32mb (Secondary Display)
Creative Labs Soundblaster (Live!)
1280 Megs of PC133 RAM (PNY)
Linksys 10/100 PCI Ethernet Card
Maxtor 60GB HD 7200
Maxtor 12GB HD 7200
Seagate 10GB HD 5400
Buslink 52x24x52 CDRW
Any help would be greatly appreciated! Do I need to set my FSB to 133 so I can use the 1700? I have updated my BIOS to the latest version. How would I increase the FSB?

Welcome
Shutdown and remove jumper J17 (see manual - jumper near ram slots). If no boot, clear CMOS and try again. Be sure to use Fail Safe Defaults for install.
You've got a really heavy load, and hope your PSU is up to it. Do you have at least 200-220 combined watts on +3 and +5 circuits of PSU (see PSU label or maker's site).

K7T Turbo2 ver5.0 won\'t reboot

I just recently bought a K7T Turbo2 (MS-6330) motherboard and I'm having a problem with it rebooting. I can't get the board to do a warm reboot. It works fine if I turn off the power and then turn it back on but even changing the BIOS settings won't allow it to reboot. I'm building this computer for someone and I will not give them a computer that won't reboot!!! I've tried to contact MSI techinical support and they have never answered me (through E-mail). I've read some other posts (in other forums) about problems with the EXACT same thing happening due to a chipset problem (KT133A) If anyone has had this problem or knows a solution please respond. here are my Spec:
K7T Turbo2 ver5.0
AMD Athlon 1200MHz (200MHz) CPU
AMD (Cooler Master) provided CPU Cooler
Matrox G400 Graphics card
2 x 64MB Crucial PC-133 Memory
P.S. I've tried other (known good) memory and graphics cards and I still have the same problem.

Well after waiting two weeks to get my replacement back from MSI I got another bad board. I haven't talked to their tech support about it yet but I think I'm going to get a different board from another manufacturer. In addition I'm going to make to STOP suggesting anymore MSI motherboards and I will definitely not choose them for my upcoming System upgrade. Just for reference.
The new board will not even POST. Or turn on for that matter. I checked all the jumpers. Unplugged everything else from the board except video, memory and processor (all proven good by another system).
I'm sick of playing with this company and I have a computer to build for someone. They just lost a formerly loyal customer. I'm not spending my money to ship it back again.
P.S.
I assume whoever sent back a KT333 motherboard and left the manual and D-Bracket in the box is going to be upset because they shipped my motherboard back in that box with the manual and the D-Bracket inside. May as well let things bounce around in the box during shipping the BOARD WAS DEAD ANYWAY!!!!!!!

Ms-6330 (k7t turbo2) dead board!

Similar Messages

Maybe you are looking for