Ms-6337le5 vcore adjustment problem

hi
i just replaced my old enpc motherboard with 6337le5;
it seems there is no way to increase core voltage more than 1.600V; this is not enough!!!!!
can anyone unlock the vcore to full range (1.300 to 2.000v)?
don't you just hate when vcore is limited?
hot about releasing a beta bios?
thanks

hey assaf, i am not mad at ya :D ; i am graceful that you replied my posts.
i like to point out that msi is trying away from a responsible m/b maker; at least one of the review of 865 p4 m/b review indicates; vr-zone.com's review "Intel PAT Enabled 865PE Boards Roundup" said msi 865pe neo2 let users change vcore to 2.3V!!!!!!! probably the "intel designed termal solution" would not be adequate to cool down the p4 other m/b makers was bit shy from 2.0v at most.
i disabled the full screen logo, and i saw the post of caps of volts sources, and interesting enough the tualatin's core voltage was caped @ little less than 1.8v. i think since the board will switch back to lower voltage if the monitored voltage is highter than the upper limit; if the voltage regulator can supply stablly about 1.750v, then i think users like me should be able to set it to such voltage. other 99% would be protected from the voltage upper limiter, and perhaps a short warning do the job.
i also suspect that msi did not design rigorously enought that the voltage regulator can NOT provide stable voltage to the core while providing 1.25v to Vtt
whatever the reason, my first msi was such a disappointment. like other m/b makers, it is hard to get any bios supports for an old m/b even if there is a problem.....i really wish either openbios or linuxbios can do better than award, so i can do whatever i want to do.
thanks assaf for your toughts
ps e7205 board from the asus is not $159; it is $59 though it is a oem "delux" edition meaning no software and fewer cables( no sata cables, no extra 2 usb2 cables) it has a gbe, 2*ieee1394, 6ch audio,4*usb2.0,2*sata; i think it is a good deal, but if my tualatin can go 133+fsb again, i would not buy it otherwise i would buy it + 2.2ghz p4 with hyperthreading enabled e7205 can do 200mhz+fsb but memory interface is syncro only.

Similar Messages

Vcore adjust problem

I have a problem when I'm gona set vcore to 1.7V, then the comp woun't boot or post at all. my first thought was PSU, can this be the problem?

i think KT6user gave some good advice here thomas, so dont go bashing on him.. LOTS of stupid people come into these forums and know there board came with something called "DOT" and they can "overclock" but lots dont know it takes life off CPU, sometimes drastcially.. raising Vcore to MAX on board will DEF shave life off of CPU considerably, and kt6user was just giving the other side of the story to raising your voltage, and why not to go that high..
oh, and i overclock, and i DO CARE about shaving life, so i dont go as high as some.. i dont raise Vcore... but i do overclock...
i have tried mine at 1.7 Vcore, no POST either.. that was when i was experimentingwhen i got my board... i can always go into CPU-Z, and it tells me i NEVER use any Vcore about 1.58.. that Vcore meter never goes above that, no matter how high i put it.. anyone else find this odd? i know the board is supposed to come with cool power consumption reduction stuff, (in corecell in think), but if i set Vcore to IE 1.6, i would like it to GO to 1.6...

Vcore adjustment on 645 Combo-L?

Hi,
I am commissioning my new PC.Currently consisting off:
645Combo-L motherboard
1.7 G Celeron
256 MB PC2100 DDR.
20GB Seagate HD
Generic PCI graphics board.
The system passes POST and will boot up DOS, but the system is to unstable to allow an install of W2k or even W98.
The Celeron Packaging states 1.75V, but the BIOS health monitor gives the Vcore as 1.69V, which seems away to low for the Celeron and may be the reason for the instability.
How can I adjust this? I can only successfully run DOS, but there appears to be no DOS software for this adjustment.
MSI seem only to provide Windows software for Vcore adjustment.
Is there any way forward?
Your advice will be most welcome.
Codger

Thanks Assaf for pointing out my error regarding voltage.
That blows away my theory as to the cause of my system instability.
I am using the "safe" BIOS defaults ie FSB=100 PC2100 = 133
and CPU clock = 1.7GHz.
I have changed the memory,the HD, the HD cables and the power supply, without resolving my problem. I don't have access to a spare Celeron to try, but what are the chances of a Celeron that passes POST and can load up DOS from a W98 boot floppy, being faulty in such a way that it crashes when installing Windows?
regards
Codger

645 Combo-L (MS-6737) VCore adjustment ?

Hello,
i have purchased the MSI 645 Combo-L (MS-6737) Board.
In the BIOS there are several functions for overclocking, it is even possible to adjust the AGP Voltage.
But i did not find any options to increment the CPU VCore, will there be a future BIOS Upgrade to enable CPU VCore adjusment ?
Thanks for any answer.

hi,
yeah, that is where it should be. But there is no such option. Look here -> http://www.geocities.com/myouterspace2002/bios.html
Thats how it looks, but Bios 1.1 added the point "AGP Voltage Adjustage" there.
So if they are able to add that Option, is there a new Bios in planning adding a CPU VCore adjustment option ?

Where the hell is the Vcore adjustment for the PT880?

i'm so pissed right now, i just updated my PT880 MSI board BIOs and for some reason the dang vcore adjustment disappear. i thought new bios = better. not worst :(

PT880 series, 1.9 best bios............ and if you have Prescott CPU forget changing Vcore

Copy and paste adjustment problem/ possible bug.

Hi all
I have just encountered a very strange problem/ possible bug.
I have been working on a file in photoshop cs5 that had come from lightroom 5.3. This was then saved (automaticaly becomes tiff file in Lightroom). I then wanted to make some more adjustments to it in lightroom (using local adjustment clarity). I then tried to copy the settings of the adjustment brush from the tiff to the original raw file. This is where it gets very strange. The adjustments are copied but they are rotated ccw by 90 degrees! I can replicate this every time.
Could someone else try to see if this problem exists on their catalogs or if its a corrpution problem my end.

Noted on the bug, thanks.
1762hd wrote:
Hi Geoff
Heres the summary for bug report - please note this bug also affects radial filter/healing brush and crop
Scenario
1 open a portrait raw image in photoshop using render using lightroom (I am using cs5)
2 back in lightroom make a change using the - adjustment brush/ radial filter/healing brush or crop - to the newly created tiff image.
3 copy and paste this adjustment to the original raw file.
problem
all effects are rotated.

Color Adjustment Problems

Can someone help me figure out what I'm doing wrong or what is going wrong. I am trying to get rid of green eye on a dog but I cannot seem to pick the eye color from the photo.
I'm starting with the green adjustment (not that this matters). I'm trying to pick the actual shade from the photo.
So I click on the color square:
The hues I get when the cursor is over the eye vary from oranges to yellows even though I see nothing under the cursor that looks anything like those hues. But sometimes I can get a hue that looks close, like in the shot below:
So I click and the result I get in the color adjustment often is nothing close to the color I picked. In this case it became red:
Any ideas?

I posted a problem related to this (but not exactly the same) a year ago and tried all the usual troubleshooting steps then with no success. The problem was on more than one computer and with photos from different cameras. I gave up and assumed it was a bug that would get fixed. I haven't touched the color adjustment bar for a year. Since that time I have installed a new video card, upgraded to Mountain Lion, installed every available update, and have rebooted many many times. I have also reinstalled Aperture from scratch (from disk) at least once and gone through all the Aperture updates. Today I did try trashing the Aperture preference file and rebooting. Neither worked. Prior to a year ago I had no problem.
The color bar works some times then will quit working. Other times it returns the wrong hue from the eye dropped (as described here), sometimes I get what looks like the right hue but the sliders have no effect until I "apply to entire photo" and all of a sudden the change takes effect. I was finally able to coax it into submission for this photo but it took more than a few tries.

Vcore + Booting problem

Hi,
I have posted previously (and thanks to all for responses).
I now have the following problems:
1. Computer will not boot from cold, or from a normal windows reboot. I am required first to remove the power cable, then plug it back in and hit the power-up button.
2. Through trial and error with my previous problem I discovered that the only way I can keep my computer stable is to use the nvsystem utility to reduce the vcore voltage to 1.5. At default (1.65) the computer will hang after prolonged use - with no extreme temperatures being reported.
This wouldn`t be so bad, but the nvsystem util is buggy as hell and crashes my comp completely 4-5 times before finally working.
I have tried the stickied method of setting vcore voltage in bios with no luck.
If you have no advice, some sympathy will be most welcome anyway.
Specs:
XP 2800+ (TB core) @ 2.25Ghz w/default fan + arctic silver 3
MSI K7N2 Delta
2x512 Kingston Value Ram (I know, I know....) (1:1 w/fsb)
Terratec EWS 88MT
ATI Radeon 9800 pro
No-name 350W PSU
Thx

Quote
Originally posted by Bonz
Ok now that you have bought a decent PSU for this power hungry rig it's time to spend a little more cash on some nForce2 approved RAM and you'll be all set!!
After that you'll be humming along and whistling a happy tune!!
Bonz
Thanks for the feedback - and how I long to whistle a happy tune.
Given the nature of my problem, how confident are you that a pair of good quality 512Mb sticks will be the answer?
I`m not questioning your advice - I`m just not entirely convinced I won`t end up going out and buying a new mobo, then a new cpu as well if the new memory doesn`t clear up the problem.
It just seems strange that a voltage reduction in the core would *increase* stability - pointing to a heat issue in the cpu - but all temps are well within normal thresholds. Also, it would seem strange, given that I now own a quality psu that any core voltage setting would interfere with the supply to the ram.
As you can tell, I`m at my wits end, and also on the verge of replacing all components other than my gfx card. :D

Nokia 2700 screen adjustment problem

Few days back I purchased 2700 classic. Its functionality is fine but the outer screen from where we listened the phone looked not totally fixed. There is a gap between the screen and outer cover. Often When I pressed from that side then it lookd adjust (see attached image) I want to ask whether it is as designed or there is some problem?
Attachments:
Screen_Gap.png ‏75 KB

Yes of course in Pakistan. Following is the address taken from Nokia site:
Nokia Care
Address:
First Floor, Sheikh Plaza, Near KFC, Murree Road, Saddar. Rawalpindi
City:
Rawalpindi
Phone :
+92 51 5793505-6
Opening hours:
10 A.M till 6 P.M
Email address:
[email protected]
More information:
GPS location: 33°35'37.35"N, 73° 3'20.44"E
I am really very disappointed.

Photos become greenish, adjustment problem

Hi, all of the photos on one of my projects became greenish, And on the inspector window is shown " This photo was adjusted using an ealier version of Apples' Row process". All of my other projects are fine. None of softwares were updated. How can fix the problem? Should I reimport the pictures?

If the adjustment has been created with an earlier version of raw support for your camera, then it might help to reprocess the master image files. This will recompute the adjustment with your currently installed raw driver,
Select the project in question and all images in it, then ctrl-click and choose "reprocess photos". You will be given the choice to do the reprocessing only with photos having already adjustments or with all images, and also if you want to create new versions or to replace the old versions.

Weird contrast adjustment problem...

I've been attempting to emulate the in-camera settings I use on my Olympus E510 in order to preserve highlights, but are those that are only used by the Olympus Viewer software. In doing so I have found what might be a bug, although I'm not sure what with.
I've left Raw Fine Tuning to the Apple default settings, and using the 'Highlight/Shadow' view. If I see clipping in both shadows and highlights, I've been trying out a method of turning down the contrast a little (using the Enhance brick). One click on the arrow sets it to -0.05, which is just enough usually.
However, I have found that it often recovers more of the shadow than the highlights. If I then try to bring up the Blackpoint adjuster, the shadows darken, but the blue indicator does not operate at all, it seems like the scale in the histogram has hit a kind of wall, and doesn't actually move down to the clipped zone.
At the other end of the scale, the highlights display as expected, and the red clipping indicator shows up as you make adjustments.
Anyone else seeing this?
Thanks
Andy.

I just figured something out. If I disable the three finger drag for the trackpad the problem goes away. That's a weird bug. Any workaround?

SPAU / SPDD Adjustment Problem

Hi to all and thanks in advance for reading my question.
I need to edit a program, but, when I try to, I get the message "EU 526" that instructs me that the object I'm trying to edit was already changed or enhanced and that this object has a new version imported to the system with a Release upgrade, and this new version was not reconcilied with the new version.
Ideed we have applied a support package and we are correcting a problem that were found in a standard, following a information sent to us from SAP.
Then, I go to SPAU to run the modification adjustment, but the object <b>isn't at the list of the SPAU objects</b>.
What I need to do in this situation? How can I solve this problem?
Thanks again,
Umberto

Hi
see the doc
What objects will come in SPAU and SPDD?
All the objects which are modified, after tansporting to the current system,
will be listed in SPAU and SPDD. SPDD contains the list of all modified Data Dictionary objects, like tables, dataelements, domains,view...etc. The rest of all the modified repository objects will be listed in SPAU.
What happens to the modifications done in the older version when we upgrade the version? (with Modification assistant and w/o)
After the initial upgrade happens, we have to do adjustments from SPAU/SPDD to maintain or reset the changes. That is, from the list of objects in SPAU/SPDD, you have to either carry forward the changes to the new version, by choosing the option ADOPT CHANGES (available on right click) or RESET TO ORIGINAL (available on right click).
Will they come in these transactions?
Ans: yes, they will be listed in these transactions, after the BASIS updgrade activity.
And what if we apply some patches(Notes) to the system? What is the impact of these patches to the SPAU transaction?
Ans: Patches will be supported by the version upgrade. In case of notes, we have to verify whether these notes are supported by the new version (you can go into http://www.service.sap.com/notes to verify this. Also, we have to analyze whther the code in the note is already incorporated in the new version. In this case you can ignore the chanes choosing RESET TO ORIGINAL option
http://help.sap.com/saphelp_erp2005vp/helpdata/en/2e/6d66587d9011d396b60000e82de14a/frameset.htm
http://www.sap-img.com/bc018.htm
http://help.sap.com/saphelp_nw04/helpdata/en/c6/068d380be34e6ce10000009b38f842/content.htm
http://help.sap.com/saphelp_46c/helpdata/EN/60/d6ba7bceda11d1953a0000e82de14a/content.htm
Reward points for useful Answers
Regards
Anji

ENVY 15 - 3040NR Brightness Adjust Problem After upgrade to Windows 8

I agree removing windows 8 is not a viable solution. Also, the Windows 8 drivers have been released and they still don't fix the problem.

Hi, I also have a HP Envy 15-3040nr and cannot for the life of me get the brightness to adjust at all. I'm using the most recent drivers from dec 10, 2012 still nothing. It's bad enough you lock us out of advanced bios settings as far as clock and bus speeds go, but then you make us have to go through your website to get drivers that's already out of date on debut. No one pays $1200 for a laptop with dedicated graphics and expects to be unable to reduce brightness. Over the course of the time I have had this laptop and has released well over 10 updates yet your engineers have only produced 3 hp certified driver and 2 were based of the same build. What are you guys doing wrong that Asus, Lenovo, even dell can get this kind of thing right. We need real solutions for the amount of money involved not half-assed responses like " uninstall windows 8 and go back to windows 7 " . There has to be a engineer that actually cares enough to fix this !

Brightness adjustament problem

When i start up my iBook it shows on screen the brightness level and when i move the iBook it goes out and when i adjust the brightness using the F1 and F2 the brightness selfadjust to the maximum level every time after i adjust.
I´m thinking that some button is stucked on...
I don´t know if could be this.
Please help me!!!!!!!!!!

And one more thing that i forgot...
when the brightness level displays on screen i can´t do nothing more cause if i click on Finder, for example, the cursor roll out for every option and do not stops until i click on desktop or out of finder.
I´m thinking remove the keyboard and look for something wrong.
Before i´m looking for a better choice,
i don´t no but this seems like a hardware problem and no software problem do you agree?????

VCore Voltage problems

Hello, again...
I've been silent for a while(after I had to RMA board once to MSI and got new one back), just being happy my machine works. But now, after a while, I just wanted to try to get my CPU to a bit more faster settings.
Problem is, I can't get beyond 253 FSB without raising VCore voltage from 1.6 -> 1.7. When VCore is at 1.6, CPU-Z and BIOS Health monitor shows it is nicely near 1.6 volts. But when I raise VCore voltage from BIOS to 1.7 it starts to jump between 1.8 - 1.9, both BIOS and CPU-Z shows same behaviour. It wont drop below 1.8, so it's like I did set VCore to 1.8, but I didn't. I did check..
Now, of course, I could run it at 1.8, but it is a bit too much for my liking, I would like to use 1.7 volts setting. Does anyone else have this same problem?
Is this BIOS problem or what? I dunno, and I do remeber that my last board(which broke) did the same thing.
Thanks.

Hi Lamy. 253 is nothing to complain about. I assume you are at a 5:4 ratio since your ram is only DDR400, which means you are at it's max rating. At that degree of overclock you are probably overloading your power supply at times. Have you tried dropping to a 3:2 ratio to see if the ram is the problem.
ryede, I'm getting tired of threats from people planning on switching motherboards. Read the rules - there are no MSI rep's here; we are all users. You have one post to your credit with minimal information supplied, and to top it all you are trying to hijack someone elses post. Besides, exceeding 250 FSB is an accomplishment that few achieve.

Ms-6337le5 vcore adjustment problem

Similar Messages

Maybe you are looking for