Ms 7030 JFP1 connectors and power on problem

I have built my new PC and the damm thing will not power up. I have played around with various JFP1 configerations for the connecters, following the user a manual. When i turn the power on i get nothing from the power supply or fans, its just dead. I know the power supply is good, i tested it on an old system. Can anyone help???
my specs are
1. MS 7030 k8n neo fsr (the one with 2 SATA slots not 4)
2. AMD 64 processor 3700

i'm not sure. i've done this a couple of times before on various motherboards (by accident of course ). if you power up with the CMOS jumper in Clear position, nothing happens. move the jumper back, and then it powers on as normal (obviously with BIOS default settings). i think its actually moving the jumper while the system is powered on that is to be avoided...
however, i'm not going to recommend anyone tries powering a board on with CMOS jumper set to clear just "out of curiosity"

Similar Messages

  • Major Freezing and Power off problems.

    So this is going to be kind of a long post, but if there is anyone out there who knows what the **** I can do to solve this issue I would really appreciate it. I bought an 8gb iPhone when they were first released last summer. Just 2 days ago the phone started to power itself off if it had been in sleep mode for more than a few minutes. I tried everything in the book (reset, reset settings, restore, etc.) Nothing helped. I went to an apple store and since the genius there was able to reproduce the issue they just gave me a brand new phone right there. Awesome right?! Wrong! After syncing the new phone with iTunes I am now having even worse issues. The brand new phone powers off in the middle of calls and other apps. And sometimes the phone will freeze completely. I tried everything in the book again. Finally I did a restore, and this time tried erasing all media content (music, photos, videos.) This seemed to do the trick as I didn't have a problem all night and pretty much all day. But just about 15 minutes ago the same problems started again! I'm losing my mind over this! Please help!

    It was taken out of a white box at the store. On the side of the box there was a label that said "Replacement 8GB iPhone."
    You probably got a bad refurbished unit. It happens. If they rebuilt a unit with an intermittent problem, and they don't catch it during testing, the next guys going to have a problem. I repaired a lot of RCA XL-100 solid state modular TV sets in the 70s. Every module we got from RCA was rebuilt. I would say we had problems with about 10% of them. They would work out of the box, but usually would act up after they got warm.
    Dave M.
    MacOSG Founder/Ambassador  An Apple User Group 
    Creator of Mac611 - Mobile Mac Support (designed exclusively for an iPhone/iPod touch)

  • Camera and Power button problems!!

    I have 2 major problems with my playbook. First problem is that the camera doesn't work. When I press the camera button, black screen pops up without any buttons visible. Sometimes an error message pops up saying that the camera is in use and won't be load up. Second problem is that when I turn the screen off by pressing power button and try to turn it on again by pressing the button again, it won't turn on. I can only turn the screen on again by swipe across the screen. The fact that my playbook doesn't work properly bothers me a lot since the problem arose only 3 months after I bought the device. What should I do to fix these problems??

    I have seen post where the turnaround was 3 days. You must backup your files first because the PlayBook will be wiped clean. Here are the contacts in Germany.
    Uni Tech Centre
    Universitatsstrasse 140
    44799 Bochum
    Germany
    Bochum
    Alleestraße 165a
    44793 Bochum
    Germany
    Frankfurter Straße 63-69
    Eschborn
    Frankfurt
    Germany
    65760
    Niederkasseler Lohweg 18
    40547 Düsseldorf
    Germany
    Ubitexx
    Kustermann Office Park
    Balanstrasse 57
    Munich, Germany
    81541
    Scoreloop
    Central Tower
    Landsberger Straße 110
    Munich Germany
    80339

  • Early 2013 15" rMBP (LG) Screen and Power Save Problems

    OK, so the first frustration is that I have this new 15" rMBP set to never sleep while on power.  I routinely come back to it, only to find that I am logged out and all of my apps have been closed.  Very annoying.  But now also this:
    Only way to solve is to close lid and re-open or reboot.  Do you bright folks think this is firmware/software related or is it because I lost the lottery and got an LG screen?

    When you say NEW what do you mean by that? If it is older then a couple of weeks it really isn't NEW, at least the way I think (New is I bought it yesterday to several days ago). If it is less then 14 days old take it back and return it for a full refund. Apple has a 14 day No Questions Ask Return Policy for Full Refund. Then buy another that may work correctly.
    If older then 2 weeks then the only thing you can do it take it to Apple and have them fix it, if possible, or replace it with one that works correctly.

  • Z87-G41 Bios 1.5 and Power Off problem

    Hi,
    since i upgraded my Bios to v1.4 to v1.5 i experience  many shutdown Issue  under Windows 8.1: (Z87-G41)
    The system shuts down but the MB refuse to power down (Screen off but CPU, disks and fans still running). Need to keep power button pressed to be able to power off
    I reverted back to Bios 1.4 and everything is fine now
    Maxx

    Please contact MSI Technical and report your difficulties encountered with the V1.5 revision.
      > How To Contact MSI <

  • System slows down and power up problems

    Hi,
    I have a Rev A G5 iMac (1.8Ghz, 1.5GB Ram) which has been working fine since purchased in 05.
    Over the 5-6 weeks we have been experiencing system slow downs. All applications will start running slower and slower (not heavy usage, mail, safari, BT client running and occasionally iMovie) to the point have to restart.
    But when restarting the iMac it will not power up, it starts and 1 sec later shuts down. So I leave for a while and try again, and it will work although the fan is extremely loud.
    I was having to restart every few days but now its to the point of a few times a day.
    have run hardware test and all is fine...and as do not have applecare want to see if can do anything myself before taking in for a quote/repair.
    Oh another thing, the superdrive will not burn via finder anymore only via toast...that started at the same time as the rest.
    many thanks
    Zara

    Hi Zara - have you tried opening the back and vacuuming out several years accumulation of dust? You can also try resetting the PRAM and the SMU and see if that helps.
    Please post back,
    Miriam

  • DMS Connector and DMS Search Problem

    Hi all,
            We have a requirement of connectiing DMS with KM.I have installed DMS Business Package and Configured Repository Manager.Here are the Details
    Description: DMS Repository Manager
    Prefix (must start with /):/dmsrm
    Repository Services:comment,discussion,feedback,layout,personalnote,properties,rating,statemngt
    Property Search Manager:< If i set this too CM Search Manager,in Document Explorer it is throwing an error "Uable to find the Repository Manager"
    Versioning Manager:Blank
    Security Manager:    Not Set
    ACL Manager Cache:   Not Set
    Windows Landscape System:   Blank
    Lock Manager:   com.sap.pct.plm.dmsrmconnectorforkm.DMSRMMutableLockManager
    ReadOnly:   No
    ShowClassification:   Yes
    ShowObjectsLinks:   Yes
    ResourceValidity:   30000
    StorageCategory:   ZHTTPPRD
    SystemAlias:   SAP_DMS
    VariantPrefix:   KM
    Now if i dont set the Property search Manager,i can bring all the documents from DMS system.But iam not able to search the document,while indexing it is throwing an error (Retrieval Error).
    If i set the Property search manager,In document Explorer it is throwing an error ( Unable to find the repository Manager).
    Anybody having any clue on this,Plz do give me a solution for this.
    Will reward with the Points.
    Regards
    Santosh Saraf

    Hi John,
    the performance issue is not the TREX search. In most cases it takes long time to check if the user have at least read permissions to the document listed in the search result list. That's why it takes more time to display 20 hits than 5 hits.
    Using more or less repository services doesn't change ther performance for the search result.
    Using a user with Content Administrator permission must have the best performance because in this case ther document permissions are not checked.
    To improve the performance you can try to use a ACL cache or increase the size of the ACL cache.
    Best Regards
    Frank

  • MSI 6800GT-T2D256E and power problem?

    I've got ASUS A8N-Deluxe mobo, Nexus 400W PU and new, bright and shiny MSI 6800GT-T2D256E
    And I get the damned:
    "The NVIDIA system sentinel is reporting that the nvidia powered graphics card is not receiving sufficient power. To protect your hardware from potential damage or causing a potential system lockup, the graphics processor has lowered its performance to a level that allows continued safe operations."
    message...
    Tried diffrent lines from PU, different drivers, nothing. I get the message right after login.
    One funny little thing: there's a sticker on the power cable that came with the card (close to the 2x3 connector) that says:
    For use with RADEON X800 series graphics card only.
    Could this be the problem or are the pwr cables the same for 6800's and X800's? Card works the same with or without pwr cable.
    Looking from the left side of an open case (w cable attced to the card) there are two wires going into the leftmost holes of the 2x3 connector - yellow (top) and black (bottom).
    Here're the PSU specs
                     Min Load  NormLoad    Max Load   Load REG. Line REG. Ripple & Noise
    +3,3V        0.5A        15.0A           3.0/30A   ±5%     ±1%   50mV P-P   
    +5V            1.0A       14.0A         10.0/28A   ±5%          ±1%   50mV P-P   
    +12V1        1.0A         7.0A            4.5/14A   ±5%           ±1%      120mV P-P   
    -12V2        1.0A         8.5A           5.55/15A   ±5%            ±1%   120mV P-P   
    -12V           0.0A        0.4A            0.5A     ±10%    ±2%  120mV P-P   
    +5Vsb        0.0A         1.0A            2.0A     ±5%        ±1%   50mV P-P
    http://www.nexustek.nl/nx4090.htm
    I have 20pin and 4 pin pwr connectors connected to the mobo.
    Any ideas?

    Update:
    Tried HEC 475W psu - didn't help. Went back to the store, they tested the card and it seemed to run just fine.
    So it's not the card nor the power cord problem. Guys at the strore said - get better psu. But I've tried better psu?!
    So I threw out everything exept HDD - no luck.
    This brings me to another question. I keep noticing peaple talking not just about watts but amps. My Nexus and that
    HEC I tested produce 14 and 15 amps respectively.
    Sadly in a small country stores don't keep expensive psu's on they shells. So I should order one. I want to be sure before that.
    Any comments on the amperage issue? 

  • This mini is operating OSX 10.6.8 and trying to update to Mountain Lion but upgrade stops and a black overscreen displays saying to power off and power on.  The upgrade fails.  What's the problem?

    This mini is operating OSX 10.6.8 and trying to update to Mountain Lion but upgrade stops and a black overscreen displays saying to power off and power on.  The upgrade fails.  What's the problem?

    Hi Fred,
    Could be many things, we should start with this...
    "Try Disk Utility
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at the top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair. Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)

  • Text problems on X40 Access Connection​s and Power Manager

    Recently, and possibly in conjunction with a recent Lenovo update, Access Connections and Power Manager (at the least, there may be other programs that have problems too, but I have not checked all) display all text as little boxes.  The functionality is still there, but it is kind of hard to figure out what's what.  I have PM 1.6.3 (just installed the latest), but not sure of version of Access Manager, as I can't see it.
    I can email a screen shot if needed, but could not figure out how to put one in here.  Any help would be most appreciated. 
    Bruce

    Hi Sami,
    I just got stuck on the same problem as you and following is what I found in details fro ThinkVantage Access Connections version 5.30. Hope this helps.
    Jakub
    <Limited User>
      A Limited user can create and apply only modem profiles. However, if
      Administrator sets "Allow Windows users without administrator
      privileges to create and apply location profiles" option in the
      Global settings then the user can create and apply any kinds of
      profiles in the system.
      Also, a limited user cannot:
      1. Edit setting for the Automatic Ethernet and Wireless location
         profiles switching.
      2. Edit Global settings.
      3. Edit profiles created by another user in the system.
      4. Renew or release IP in the Diagnostics panel.
      5. Export profiles.
      The limitations on Power user also apply on Limited user.

  • MacBook Pro whine problems plus wake-to-sleep problems and power adapter

    Hello. I bought my MacBook Pro for some months ago as "refreshed". They said that it worked fine and had no problems. That just the owner had left it because he didn't want it anymore. However, sure, it has worked great. But it has a loud annoying whine. It is very annoying. Nope, no Mac OS X update or firmware update have worked. I guess I should leave it in, or should I? Maybe I can get a MacBook Pro Intel Core 2 Duo instead of my current MacBook Pro Intel Core 2 Duo (2.0 GHz). Or what do you think?
    The second problem is with wake-to-sleep. The latest update said it would fix this issue. But it is even worser now than it was. (and it was bad). It seems like when the power adapters gets unplugged, that it goes to sleep then. But it also goes to sleep sometimes and is hard to wake up, so still same issues there.
    The first but last. My Power adapter is kinda broken, it works, but the quality seems kinda bad. These two things that you plugin to the wall, they are bent so it kinda hard to plug it in.
    Anyone knows what to do?

    It whines when on batteries too.
    Then just install the kernel extension, aand pure silence I don't think that it decreases a lot the battery life. It is safe to try, and it can be installed uninstalled dynamically to the system. It has an automatic installer, which will enable it each time your computer starts. If you do not want it to be automatic like that, let me know, I can explain how to controle loading/unloading of the driver

  • Hi, I'm having a macbook pro here and it spoiled after a year of using, i though it was the power adapter problem because when i try to charge my mac battery that is depleted it shows a very dim light and my mac won't start up

    Hi, I'm a macbook pro user but recently my macbook just spoiled, i though was my power adapter problem because when i charge my mac battery that is depleted, it shows a very dim light and my mac just won't start up, even i bought a brand new 80 euro power adapter it still give out the same result.

    when I switch it on, the little led  light it up and u can hear the fun running and after 5 to 10 seconds switched off again /  ive got all my recordings in there
    Try Resetting your Mac's PRAM and NVRAM
    If that doesn't help, try Resetting the System Management Controller (SMC)
    in really disappointed with apple,
    Serge... you are aware that you are responsible for backing up your importanta data correct ?

  • My Iphone 4 will not turn on all it will do is show the iTunes logo and and arrow point to it with an image of the connector to power cord. Ive tried to turn it off, taken out sim but nothing

    My Iphone 4 will not turn on all it will do is show the iTunes logo and and arrow point to it with an image of the connector to power cord. Ive tried to turn it off, taken out sim but nothing

    Hello there, FrancesCech.
    The following iPhone Troubleshooting Assistant should help with what to do with your situation:
    Apple - Support - iPhone - Restore Troubleshooting Assistant
    http://www.apple.com/support/iphone/assistant/restore/
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro D.

  • My iPhone 4S lost simcard reference several times a day and issue message invalid SimCard. I have already replaced simcard three times and not solve the problem. It's necessary to power off and power on to solve it. Could someone help me?

    My iPhone 4S lost simcard reference several times a day and issue message invalid SimCard. I have already replaced simcard three times and not solve the problem. It's necessary to power off and power on to solve it. Could someone help me?

    Return your phone to Apple for evaluation

  • After ios upgrade to 7.0.4 i got power botton and no sim problem need help      help

    after ios upgrade to 7.0.4 i got power botton and no sim problem anyone having this problem?

    Installing an iOS update does not add a physical button.
    As for the "No SIM" message, try removing and reinserting the SIM or replacing the SIM.

Maybe you are looking for