MS2026 -anvna Wait for Acquisition Complete -ERROR
Hi Everyone,
I wrote a labview program (LV 7.1) with instrument MS2026A VNA (Anritsu) and it was working fine.
However the original equipmet stopped working last week and we have received a loaner (until our is fixed), same model, but does not work with my labview program. I even try running this equipment with the sample program provided by NI: "anvna Acquire Trace Example" and it gives me an error -please refer to attached pictures.
The error is in the "anvna Wait for Acquisition Complete.vi." I think it has to do with timeout (256). I have added delays all over but nothing helps. I used to have this same problem on the first instrument but it disappear "mysteriously."
Could somebody point me to way to fix this issue? Thanks very much,
Frank
Attachments:
anvna Wait for Acquisition Complete -ERROR.gif 10 KB
anvna Wait for Acquisition Complete.gif 26 KB
Hi Fvalenzu,
I have a few questions about your application.
Is the replacement instrument the same revision of the instrument you sent to get repaired?
Is the device at the same address?
Are you able to successfully communicate with the instrument in max using GPIB commands?
You might want to verify the program is calling the instrument by the correct alias or address and you are calling the device correctly. Also, I would check and see if there is a newer version of the IVI driver for your instrument. IVI drivers can be found at the link below.
ni.com/idnet
Regards
Message Edited by Andy L on 08-17-2007 06:25 PM
Andy L.
Applications Engineer
National Instruments
Similar Messages
-
Why "wait for operation complete" error ?
HI,
When I use the vi "Read multiple waveforms" there are an errors that appears in the VI "wait for operation complete" and I cannot found the cause of this error ! Can you bring me your help on this suject ?
Thanks you beforehand
Here my vi in LV2013
Attachments:
Sans titre 1.vi 17 KBIt would have helped if you would have stated that this was for a Tektronix 7000 series scope.
I see two possible issues here:
1) The scope never sees the trigger and therefore never sees a waveform to capture
2) The scope is setup to continuously capture waveforms. Since the scope isn't stopping, it won't report being complete.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions -
Timeout error in Wait for Operation Complete VI for TEKDPO4054 scope driver
Hi,
I keep getting a timeout error (-1073807339) when I run the "wait for operation complete" sub-VI that comes with the tektronix DPO4000 series oscilloscope driver. I'm using a DPO4054 scope. The error out source is the VISA Read STB command, but I can't figure out what's wrong. Has anyone else encountered this error? Please help!
Thanks for your time!
I've attached the sub-VI where I'm having this problem.
Attachments:
tkdpo4k Wait for Operation Complete.vi 27 KBduplicate post
Please try to keep your questions to a single board. -
Wait for move complete not waiting for timeout
Hi,
I am running a small rotary stage with a 7358 motion controller. Occasionally when I command a new position, the "wait for move complete" seems to get triggered almost immediately even though the move is not complete. Since I have put in a "halt" downstream of this to cover the case where the move times out, the move stops immediately. The problems seems interrmittent but I haven't discovered a pattern yet except that is happens for more often when making a reverse move, i.e. I go to 1000 counts as a forward move and then back to 800 as a reverse.
Has anyone seen something similar?
Thanks,
Dave
David A. Tayloroops syntax error! I put waitComplete, but it's supposed to be moveComplete as the last argument for flex_wait_for_move_complete. Just want to let you guys know that. Thanks!
-
NI Scope Wait for Acquisition to Finish Obselete in 2014
Quick Question,
In LabVIEW 2014, the NI scope Wait for Acquisition to Finish subVI is no longer used and is obsolete apparently, can some one tell me why this is and what I can use instead with the new 2014 NI scope blocks?
Thanks for your help!Query Acquisition Status until Status is "Complete" To avoid infiate loops (missing trigger event) you should set a Timeout for the loop
Alternately use hardwae and rout the End of Acquisition event to something
Jeff -
Waiting for Task Completion from multiple users
iam using Weblogic8.1 Integration BPM to design a worklist application. I need
to create a number of Tasks(number know only at runtime), assign to users and
wait for the completion of each of these task. I've tried using the Task Control
factory to accomplish this. But iam not able to hold the process instance execution
till each of these task is completed. The control gets released from the TaskControlFactory_onTaskCompleted
as soon as one of the above created task is completed.
Pls. let me know if there is a way to achieve this.
Regards
Raja V.Try to put the onTaskCompleted Control Receive in a loop which counts how
many of these
callbacks have already arrived, and the loop exit condition would be that
the count is equal
to the number of the created tasks.
Regards,
Robert Varga
"Raja V" <[email protected]> wrote in message
news:3f423f82$[email protected]..
>
iam using Weblogic8.1 Integration BPM to design a worklist application. Ineed
to create a number of Tasks(number know only at runtime), assign to usersand
wait for the completion of each of these task. I've tried using the TaskControl
factory to accomplish this. But iam not able to hold the process instanceexecution
till each of these task is completed. The control gets released from theTaskControlFactory_onTaskCompleted
as soon as one of the above created task is completed.
Pls. let me know if there is a way to achieve this.
Regards
Raja V. -
Pourquoi une erreur s'affiche t-elle toujours dans le VI "wait for operation complete" ?
Bonjour,
J'ai un programme avec lequel je relève la courbe présente sur deux oscilloscopes et qui permet de surveiller l'état du trigger de ces appareils et d'enregistrer des fichiers de mesure. Cependant en utilisant le vi "Read multiple waveforms" il y a une erreur qui apparait dans le VI "wait for operation complete" et je n'arrive pas à trouver la cause de cette erreur ! Pouvez-vous m'apporter votre aide sur ce point ?
Cordialement
Ci joint mon vi LV2013
Pièces jointes :
Sans titre 1.vi 17 KBBonjour ttom972,
Je ne trouve pas de driver s'intitulant Tektronix 7000 series sur notre site. Avez vous un lien ?
Les drivers d'instruments disponible sur notre site ne sont pas développés ni supportés par NI. Je peux essayer de regarder d'ou provient l'erreur, mais le mieux serait de recoder en utilisant des fonctions bas niveau VISA.
Cordialement,
Benoit S. - Field Sales Engineer
Certified LabVIEW Developer
Certified TestStand Developer
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
Été de LabVIEW 2014
12 présentations en ligne, du 30 juin au 18 juillet -
Iphone 4S stuck during restore, waiting for iPhone message error 9
yesterday morning when I woke up to check my Emails on my iphone 4S, my phone was complete dead. I thought battery died so plugged into charger. but even after couple of hours it didnt turned up. So I started force starting by pressing power button several times but nothing happened.
Then I pressed both home and power button for several minutes, nothing.....
Finally I connected my iphone to itunes thru my Mac air and to my surprise it said my phone is in recovery mode and needs to be restored. I pressed ok, it extracted software and then said waiting for iphone. and I was happy to see apple logo on my phone with a progress bar. I waited for almost 12 hrs but nothing moved in the progress bar. seems like it frozen. I tried disconnecting and reconnecting to itunes but everytime same error. whenever i plugeed out my phone from itunes, it errored out no. 9.
Also it is not showing any s/n for my iphone in itunes. I am very confused and frustated, read many forums and also updated my itunes, updated my software and turned on the firewall too. NOTHING HELPED.
Does anyone have any solutions to share?
Thankshttp://support.apple.com/kb/TS3694#securitysoft
-
Hi,
I am currently programming a 7344 motion control board in Visual C++.
Right now I am using the function flex_wait_for_move_complete function but it causes an exception error when passing the pointer, moveComplete, into the function ( it is the last argument).
According to the prototype, u16* waitComplete is a returned pointer the function returns. 1 if move is complete, 0 if move is not. Maybe I am referencing it and using it the wrong way.
In my function
void moveSingleAxis(..)
u16* moveComplete = (u16*)1;
//some code
status = flex_wait_for_move_complete(boardid, NIMC_AXIS1, NIMC_AXIS_CTRL, 10000, 20, waitComplete);
//status is used for error checking, but irrelevant to my problem
If I make the pointer to 0 or NULL, flex will error and say pass in null pointer . If I make the pointer to any other number it causes null reference exception error. Any help? thanks!
-Mikeoops syntax error! I put waitComplete, but it's supposed to be moveComplete as the last argument for flex_wait_for_move_complete. Just want to let you guys know that. Thanks!
-
PO OUTPUT FOR COMMUNICATION COMPLETING ERROR
PO OUTPUT for COMMUNICATION is completing with error. I tried with XDO & ICX profile values... no effect..From the log file,
Document Template Code :PO_STANDARD_XSLFO
Language Code :US
Document XSL Contents Wed Jun 13 12:31:07 IST 2012
Retrieved the Document XSL Wed Jun 13 12:31:07 IST 2012
Calling the getPOXml method
GenerateDocument::getPOXml() : l_exists 1
GenerateDocument::getPOXml() : m_whichTables MAIN
GenerateDocument::getPOXml()- Calling the POXMLGEN method Wed Jun 13 12:31:07 IST 2012
Generated the Document XML Wed Jun 13 12:31:14 IST 2012
Document XML Contents Wed Jun 13 12:31:14 IST 2012
Calling the print util method:Wed Jun 13 12:31:14 IST 2012
PoPrintingUtil.getBlobPDF(input,input) - After initializing the FOProcessor
PoPrintingUtil.getBlobPDF(input,input) - After setting the i/o stream and output format
PoPrintingUtil.getBlobPDF(input,input) - After calling the generate Method
After printutil method:Wed Jun 13 12:31:17 IST 2012
m_pdf is not null
Calling StorePDF()
Preparing to archive the PDF..
getArchiveOn(): null
getArchiveOn()=null m_viewOrCommunicate=View
getArchiveOn(): null
genDoc() : Exceptionjava.lang.NullPointerException
java.lang.Exception
rolling back the complete program
Start of log messages from FND_FILE
End of log messages from FND_FILE
Executing request completion options...
------------- 4) PLSQL -------------
Executing PL/SQL. (REQUEST ID=5822592) (STEP ID=3)
PL/SQL completed with return code of: 0
Please advice..
Thanks,
Ranjith
Edited by: user8108877 on Jun 13, 2012 1:18 PMICX was already checked.... The Issue got resolved when I select the check box "Can Change Forward-To" in the Setup --> purchasing --> Document type window for Standard Purchase Order.
Thanks,
Ranjith -
Error message. waiting for bridge cs6
can any one help me with the error message i keep getting? Waiting for bridge cs6.
Error: Waiting for Bridge | Mini Bridge panel
-
Patched Deployments issue: "waiting for another installation to complete"
I have some percent of computers which runs into above state in monthly patch deployments. I could minimal information from execmgmr, udpatesdeployment.log,
CliSpy and Client Center etc tools but that doesn’t offer much help to nail down the issue completely. Have any of you dealt to resolve such issue successfully ? Is there any efficient way to handle this ?
It seems I have
DeploymentA, waiting for the completion of DeploymentB, which in turn waiting for the completion of
DeploymentC. Is there any better approach I could take to nail down and resolve the issue. One of my finding is, KB articles installs (SCCM R3, SCCM Asset Intelligence) causes these issue as they restart (upgrade sort of execution) the
agent during the execution, I need to confirm these
VasuHi Vasu,
This issue can be caused by a deployment was previously deployed and was now deleted. This was because the clients finished installation
and wanted to notify the Server that it is done, but since the deployment was deleted, it couldn’t Notify its progress to the site server and the CCM_DeploymentTaskEx1 got stuck.
Please use the following scripts to delete the instance to test this issue.
strService = "CcmExec"
strComputer = "."
Set objWMIService = GetObject("winmgmts:" & "{impersonationLevel=impersonate}!\\" & strComputer & "\root\CCM\SoftwareUpdates\DeploymentAgent")
Set colWMISettings = objWMIService.ExecQuery("Select * from CCM_DeploymentTaskEx1")
For Each objWMISetting in colWMISettings
objWMISetting.AssignmentId = ""
objWMISetting.JobId = "{00000000-0000-0000-0000-000000000000}"
objWMISetting.Put_
Next
'Stop service
Set objWMI = GetObject("winmgmts:\\" & strComputer & "\root\cimv2")
Set objService = objWMI.Get("Win32_Service.Name='" & strService & "'")
objService.StopService()
WScript.Sleep 10000 ' Pause to allow service to stop
'Start service
Set objService = objWMI.Get("Win32_Service.Name='" & strService & "'")
objService.StartService()
WScript.Sleep 10000 ' Pause to allow service to start
Regards,
Sabrina
This posting is provided "AS IS" with no warranties or guarantees, and confers no rights. |Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question.
This can be beneficial to other community members reading the thread. -
ORA-00060: deadlock detected while waiting for resource CLOSE cursor
Hi,
I am a new member of this forum. I am working with a problem we got a few weeks ago. It is from a Pro C batch executable running on 10 threads dealing with >800 data accessed from multiple tables. The error as reported came from a package.function call.
This is the error I encountered:
process_item~G****, D***~-60~ORA-00060: deadlock detected while waiting for resource~PACKAGE ERROR = CLOSE cursor C_***** in package R***.I*** 7641
The cursor is a simple SELECT cursor without Table or Record locking.
My questions are:
*Upon the occurrence of this error, is the execution already at the CLOSE cursor line or did the error occurred between the OPEN cursor and the CLOSE cursor? There are several lines of code in between OPEN and CLOSE:
- one that calls for a package.function that simply stores parameter values to a variable
- another one which fetches the cursor. The group that holds the cursor values is only used by a single function in the package
*Is it possible for this CLOSE cursor to cause a deadlock? What could have caused this?
*From what I know, Oracle deals with deadlocks by aborting the deadlocking process while others continue, but this deadlock caused our program to hang. How is this possible? Could the root cause of the deadlock be from our threading program? This is a rare occurrence and happened only twice this year.
Thanks,
RafRaf Serrano wrote:
Hi,
I am a new member of this forum. I am working with a problem we got a few weeks ago. It is from a Pro C batch executable running on 10 threads dealing with >800 data accessed from multiple tables. The error as reported came from a package.function call.
This is the error I encountered:
process_item~G****, D***~-60~ORA-00060: deadlock detected while waiting for resource~PACKAGE ERROR = CLOSE cursor C_***** in package R***.I*** 7641
The cursor is a simple SELECT cursor without Table or Record locking.
My questions are:
*Upon the occurrence of this error, is the execution already at the CLOSE cursor line or did the error occurred between the OPEN cursor and the CLOSE cursor? There are several lines of code in between OPEN and CLOSE:
- one that calls for a package.function that simply stores parameter values to a variable
- another one which fetches the cursor. The group that holds the cursor values is only used by a single function in the package
*Is it possible for this CLOSE cursor to cause a deadlock? What could have caused this?
*From what I know, Oracle deals with deadlocks by aborting the deadlocking process while others continue, but this deadlock caused our program to hang. How is this possible? Could the root cause of the deadlock be from our threading program? This is a rare occurrence and happened only twice this year.
Thanks,
RafSELECT (without FOR UPDATE) statements are never involved in ORA-00060.
only DML statements throw ORA-00060 error -
10.6.8 Netboot - "Still waiting for root device"
Hi all,
I am having trouble with one particular 10.6.8 Netboot image that is hosted on a Mac Pro running 10.5.8 Server. (The main 10.5.8 Server is currently hosting about 15 other Netboot and Netrestore images that work with no problem.) I built the image on a 10.6.8 Server using System Image Utility from a fully updated 10.6.8 restore image on an external hard drive. The external drive was started up on MacBook, MacBook Pro, and iMac systems ranging from Late '06 to Early '11 revisions. Software update was run on every startup, but came back fully up-to-date every time and never encountered problems starting up each from the external drive.
I then ran Disk Utility permissions repair on the external drive from the 10.6.8 Server Mac Pro and built the Netboot image in System Image Utility. Although I am fairly new to this process, I have already successfully built several 10.6.8, 10.7.5, 10.8.5, and 10.9 Netrestore images as well as one 10.9 diagnostic Netboot that all work perfectly. I followed the same process when creating the 10.6.8 Netboot image.
The image I created, called 10.6.8 Diags 3.0, shows up in the Netboot list, but when I attempt to boot it shows the Apple logo for a bit before showing the "circle slash" symbol. Verbose mode shows that it hangs when starting and repeats "Still waiting for root device" over and over again and never does anything.
I have rebuilt the 10.6.8 Diags 3.0 Netboot image several times to rule out the possibility of corruption durring image creation. I have also tried to create the image from a Firewire attached external drive as well as building the data on the external drive into a .dmg on the 10.6.8 Server and then creating the image from that. All methods of creating the image yeild the same "Still waiting for root device" error when attempting to start up on any system supporting the 10.6.8 kernel.
Netboot settings in Server Admin are the same as other Netboot images that are functioning: enabled, diskless, Intel (grayed out), and NFS. I have verified that all enabled image index numbers are unique and even tried several different index numbers on the problem Neboot image.
Again, all other Netrestore images I created on the same 10.6.8 Server work just fine when added to the Netboot directory on the 10.5.8 Main Server, but the Netboot image of 10.6.8 Diags 3.0 does not. I'm not sure what else to try at this point, any ideas?Ooooh. I've been reading similar pages on cidori.org and just assumed it was one of those. Remarkable how my google searches didn't find that one. Thanks for the pointer, and I'll go try it.
Thanks again, Dan. -
Just recently I started encountering a "waiting for proxy tunnel" error in Chrome and Safari when trying to surf the web while having to use a network proxy. It seems this is some kind of malware but I cannot find how to delete it. Any help?
It means the proxy isn't working.
Maybe you are looking for
-
SAP QUERY report for vendor line items
Hi I have created a SAP QUERY report for vendor line items with fields vendor no.,vendor name,amount,company code and period.But there is one line item i donot know from wher system is getting it picked with is not in that vedor account,when i compar
-
Not able to autofill songs icon not showing up
when i plug my ipod shuffle into the usb port the icon under the souce section in itunes is not showing up so i can not autofill my songs does anybody know who to fix this
-
Cannot query MSSQL system tables over db link created using DG4MSQL
I am trying to create db link from Oracle 11g to SQL Server 2005 using DG4MSQL gateway. After creating db link I am not able to query MSSQL system views(sys.services or sys.objects) using JDBC driver. But I am able to query all user tables using JDBC
-
CS5 Won't Export to .swf in spreads
I know there's something simple I'm missing here, but I'm tired and under deadline and need help. In ID CS4, I could export spreads to .swf. In ID CS5, I'm not seeing that option in the export box and consequently, my books are coming up with single
-
Wi-Fi Networking in Location Services System Services
Hello, I'm trying to figure out what the "Wi-Fi Networking" toggle controls. This is located withing Settings > Location Services > System Services > Wi-Fi Networking. Thanks for the help if anyone can provide any. I've been searching around the we