MSE 3350 is not come on GUI
Hi
I have configured MSE 3350 but it is unable to come up on GUI.
Please help me to doing the initial troubleshoting.
[root@Gig-1-MSE-1 ~]# rundiag
11 Nov 2013 19:06:07,341 - ------------ Start Running Diagnostics --------------
11 Nov 2013 19:06:07,346 - ------------ Start MSE diagnostics ----------------
11 Nov 2013 19:06:07,433 - MSE Platform is down.
11 Nov 2013 19:06:07,433 - ------------ End MSE diagnostics ----------------
11 Nov 2013 19:06:07,433 - ------------ Start Location Server Info -------------
11 Nov 2013 19:06:07,463 - Location Server is down.
11 Nov 2013 19:06:07,463 - ------------ End Location Server Info ---------------
11 Nov 2013 19:06:07,539 - ------------ Start /etc/hosts ----------------
11 Nov 2013 19:06:07,545 -
# /etc/hosts file generated by appliance setup
# hostname=Gig-1-MSE-1
# domain=uataxisb.com
# eth0_ipaddress=10.101.2.8
127.0.0.1 localhost.localdomain localhost
10.101.2.8 Gig-1-MSE-1.uataxisb.com
11 Nov 2013 19:06:07,545 - ------------ End /etc/hosts ----------------
11 Nov 2013 19:06:07,545 - ------------ Start /sbin/ifconfig output ------------
11 Nov 2013 19:06:07,557 -
eth0 Link encap:Ethernet HWaddr 34:40:B5:D7:9B:58
inet addr:10.101.2.8 Bcast:10.101.2.255 Mask:255.255.255.0
inet6 addr: fe80::3640:b5ff:fed7:9b58/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:53618 errors:0 dropped:0 overruns:0 frame:0
TX packets:4129 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5778646 (5.5 MiB) TX bytes:326864 (319.2 KiB)
Interrupt:169 Memory:92000000-92012800
eth1 Link encap:Ethernet HWaddr 34:40:B5:D7:9B:5A
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:130 Memory:94000000-94012800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:72 errors:0 dropped:0 overruns:0 frame:0
TX packets:72 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4932 (4.8 KiB) TX bytes:4932 (4.8 KiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
usb0 Link encap:Ethernet HWaddr 36:40:B5:FC:89:FB
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
11 Nov 2013 19:06:07,557 - ------------ End /sbin/ifconfig output --------------
11 Nov 2013 19:06:07,557 - ------------ End Running Diagnostics ---------------
[root@Gig-1-MSE-1 ~]#/etc/init.d/msed start
Starting MSE Platform
Flushing firewall rules: [ OK ]
Setting chains to policy ACCEPT: filter [ OK ]
Unloading iptables modules: [ OK ]
Starting Health Monitor, Waiting to check the status.
Failed to start the MSE Platform.
Starting Admin process...
Started Admin process.
why it is showing faild to start the MSE Platfrom.
Hi,
I have done all the excercise but still the probplem is same.
even i have configured secondary MSE as like same.. it is not shown that messeage.
[root@Gig-1-MSE-1 ~]# /etc/init.d/msed start
Starting MSE Platform
Flushing firewall rules: [ OK ]
Setting chains to policy ACCEPT: nat filter [ OK ]
Unloading iptables modules: [ OK ]
Starting Health Monitor, Waiting to check the status.
Failed to start the MSE Platform.
Starting Admin process...
Started Admin process.
[root@Gig-1-MSE-1 ~]# /etc/init.d/msed stop
Stopping MSE Platform
Flushing firewall rules: [ OK ]
Setting chains to policy ACCEPT: nat filter [ OK ]
Unloading iptables modules: [ OK ]
[root@Gig-1-MSE-1 ~]# /etc/init.d/msed stop
Stopping MSE Platform
Flushing firewall rules: [ OK ]
Setting chains to policy ACCEPT: filter [ OK ]
Unloading iptables modules: [ OK ]
[root@Gig-1-MSE-1 ~]# /etc/init.d/msed status
STATUS:
Health Monitor is not running
[root@Gig-1-MSE-1 ~]# /etc/init.d/msed start
Starting MSE Platform
Flushing firewall rules: [ OK ]
Setting chains to policy ACCEPT: filter [ OK ]
Unloading iptables modules: [ OK ]
Starting Health Monitor, Waiting to check the status.
Failed to start the MSE Platform.
Starting Admin process...
Started Admin process.
[root@Gig-1-MSE-1 ~]# /etc/init.d/msed status
STATUS:
Health Monitor is not running
[root@Gig-1-MSE-1 ~]#
Please help on it.
Similar Messages
-
What MSE 3350 versions are compatible with PI 1.4.0.45?
Sounds simple, but on CCO the latest MSE version I see listed for the 3350 is 7.3.101, and its release note compatibility matrix only says 1.2.0.103. Is the 3350 no longer supported with PI 1.3 and above?
Thanks, that looks promising! I had looked at http://www.cisco.com/en/US/customer/docs/net_mgmt/prime/infrastructure/1.4/release/notes/cpi_rn_14.html#wp103402
which seems to suggest the 3350 will not work with PI 1.4. -
Report does not come up when called from Forms
I have installed Oracle 9i database and dveloper suit on my pc. When I run reports from forms, the report does not come up. I have Adobe Acrobat reader 6. The report does get created, I can see it in the cache directory.
It created an error file, I am posting the begining of this file here.
Please help.
Thanking you in advance.
An unexpected exception has been detected in native code outside the VM.
Unexpected Signal : EXCEPTION_ACCESS_VIOLATION occurred at PC=0x65553878
Function name=Java_oracle_reports_engine_EngineImpl_CGetEnv
Library=C:\orahome1\bin\rw90.dll
Current Java thread:
at oracle.reports.engine.EngineImpl.CGetEnv(Native Method)
at oracle.reports.engine.EngineImpl.getEnvs(EngineImpl.java:453)
at oracle.reports.engine.EngineClassPOATie.getEnvs(EngineClassPOATie.java:152)
at oracle.reports.engine.EngineClassPOA._invoke(EngineClassPOA.java:205)
at oracle.reports.engine.EngineClassPOA._invoke(EngineClassPOA.java:62)
at com.inprise.vbroker.poa.POAImpl.invoke(POAImpl.java:2355)
at com.inprise.vbroker.poa.ActivationRecord.invoke(ActivationRecord.java:104)
at com.inprise.vbroker.GIOP.GiopProtocolAdapter.doRequest(GiopProtocolAdapter.java:492)
at com.inprise.vbroker.IIOP.ServerProtocolAdapter.doRequest(ServerProtocolAdapter.java:64)
at com.inprise.vbroker.GIOP.GiopProtocolAdapter.dispatchMessage(GiopProtocolAdapter.java:653)
at com.inprise.vbroker.orb.TPDispatcherImpl$TPDispatcher.run(TPDispatcherImpl.java:99)
at com.inprise.vbroker.orb.ThreadPool$PoolWorker.run(ThreadPool.java:76)Hi ,
Looks like this is not a Forms side problem or even a Reports Servlet problem
Some guesses.
From the exception
at oracle.reports.engine.EngineImpl.CGetEnv(Native Method)
at oracle.reports.engine.EngineImpl.getEnvs(EngineImpl.java:453)
it looks like engine crashing. Did you see the server GUI up and running ? Server might not have started
Give
rwserver server=<server_name> in command line.
The server GUI should come up and show "ready "
You have multiple Oracle Homes on the same machine. So this could be a PATH problem.
1) Go to ControlPanel -> System - Advanced - Env variables - System Variables
Copy the IDS specific PATH to clipboard
Go to iDS_HOME\bin\ and open a command window. Set only the above PATH here. Start a standalone server
rwserver server=<server_name>
and try
(If this works you could write a batch file later)
2) For trouble shooting purposes use a different server name to start the standalone server.
3) Also look in your registry
HKLM\Software\Oracle\Home<x>\
Here please see whether you have any "very long" environment variable (say more than 256 chars or 512 chars).
This is just a guess.
4) To confirm this is not a Reports servlet problem
give
rwclient report=<report_name> + ..... <server=server_name>
If you get same error, then it is not a servlet problem. It could be that Reports server is crashing
Thanks
Ratheesh
[ All Docs ]
http://otn.oracle.com/documentation/reports.html
[ Publishing reports to web - 10G ]
http://download.oracle.com/docs/html/B10314_01/toc.htm (html)
http://download.oracle.com/docs/pdf/B10314_01.pdf (pdf)
[ Building reports - 10G ]
http://download.oracle.com/docs/pdf/B10602_01.pdf (pdf)
http://download.oracle.com/docs/html/B10602_01/toc.htm (html)
[ Forms Reports Integration whitepaper 9i ]
http://otn.oracle.com/products/forms/pdf/frm9isrw9i.pdf -
Previous data in the field is not comming when we press space bar
Hi Experts,
I am faceing 1 issue in module pool programming.i have 10 input fields in a perticular screen,
when i am pressing Space Key in a perticular input field , for some fields the previous data what i field last time is comming,
but for some fields it's not comming there, i want it should be with every field.
Finally i would like to know how to get the previous data what i have entered last time has to come when i will press space key
in a input field of screen.
Regards,
Susheel Joshi
Edited by: SUSHEEL JOSHI on Apr 9, 2010 4:47 PMHave multiple fields the same "name", are some field name or value too long.
Check your Sapgui settings [[Alt]+[F12]|http://help.sap.com/SAPhelp_nw04/helpdata/en/f9/9f9d427cab0831e10000000a1550b0/frameset.htm] and read OSS notes like [Note 399180 - SAP GUI input history depending on field (name) length|https://service.sap.com/sap/support/notes/399180]
Regards,
Raymond -
SAP Script O/P is not comming
Hi,
when i make a t-code for my SAP-script Program it is not comming properly in print form.
But when i run my print program in se38 it is comming proper out put.
Plz help me what is the cause behind this isue.
Regards,
Sunil sahooHi Sunil,
I have faced the same problem.
1)First Check initial screen and specify appropriate start object --> select 2nd radio button (For Reports)
2) On Seciond screen :-
Please check all the fields
Transaction text --> Give the specific text
Program --> Give the report name
Screen number --> 1000 (Keep it standard)
Authorization object --> can be empty.
3) GUI Support --> Tick all the check box.
I hope this resolve your issue.
Thanks & Regards,
Lokesh. -
Hi All,
I have the following getserver info from the MSE 3350,
The WCS ver. 7.0.172.0, the initial install documentation shows that the following ports needs to be opened on MSE to have successfull communications between WCS and MSE.
Can someone clarify this situation for me,.
1. From the MSE getserverinfo. the follwoing seems to be in "false" state.
HTTP : false
legacy HTTPS:false
but the communication between the MSE and WCS SOAP/XML needs HTTP/HTTPS opended.
Can I make any changes on the MSE through CLI to fix this issue. Unless this is not an issue.
2. I issued a netstat -tulpn command and I am not able to see certain ports not listening
Please see the attached text file.
Example :
TCP 443 for HTTPs
SNMP 161, 162
TCP 80
TCP 21 for FTP
TCP 16113 for MSE to WLC ( NSMP Protocol exchanges)
I am unable to see those.
Thanks
Let me know if this will cause an issue while i deploy the MSE into live production.When you go throuh the script to install the MSE, it should ask you about using HTTP/HTTPS.
you can rerun the script from /opt/bin/setup.sh (please check my pathing on this)
HTH,
Steve
Please remember to rate helpful posts or to mark the quesiton as answered so that it can be found later. -
Tuesday night I was texting a friend and when I went to open her message, my screen went blue and restarted. I just wrote it off as weird and went on about my business. Later that night, I tried to turn on my phone and it would not turn on. I plugged it up, held down the power button, and pressed the home button all numerous times. I looked online and it said to do a "hard reset" by holding down the power and home button at the same time--my phone then came on. Throughout Wednesday, it would give me a blue screen and restart--nothing major just really annoying. I took it to the local Verizon store where I bought the phone from and he said that it was some type of hardware defect and I was still under my year warranty so I could get a new one for free--the free phone won't be here until tomorrow, Saturday. I took it home and it didn't give me any trouble for a couple of hours. The next day it was cooperating and then I left town for a little while and it acted up (blue screen and then restarting) a few times. When I got home, it acted up again and so I restarted the phone and it was working fine. A few minutes later, I tried to check my messages and the phone was off again. No matter what I do, my phone will not come back to life. It had at least 45% battery last time I looked at it. I decided to plug the phone up to my computer and see what it did--my computer recognizes that there is a phone hooked to it and it says that it's in "recovery mode". It also said that if I'm having issues with my phone, that I need to reset the phone via iTunes. I guess the questions that arise are
1. Why is my phone doing this?
2. If I reset my phone, will it go back to working again? I ask that because I don't want Verizon to charge me $300 when they send me the replacement phone and I won't need it (assuming that the phone decides to work once it's been reset).
3. What type of hardware defect is this that is causing this issue, not only with my iPhone 5S but others as well?
4. Shouldn't people be notifying Apple and letting them know that they need to fix this issue?
5. Should I report this issue to Apple even though I didn't buy the phone directly from them, but through Verizon?
Any help that anyone could give me would be greatly appreciated! This whole situation has me stressed out and seriously confused.Hi, beth.lau.gr.
Thank you for visiting Apple Support Communities.
I understand you have been experiencing issues with your iPhone restarting and showing you a blue screen. I wont be able to give you an exact answer as to why this is happening. However, this is the most relevant troubleshooting article for this issue. This article also provides options to reach out to us via phone for additional assistance.
If your iOS device restarts, displays the Apple logo, or powers off while you're using it
http://support.apple.com/en-us/HT203899
Cheers,
Jason H. -
Inutilização de Nota com erro de validação no GRC
Bom dia,
Estou com um problema na inutilização de notas com erro de validação no GRC!
Quando a nota é rejeitada pela GRC, fica da seguinte maneira:
Etata obrigatória do processo : 8 (Erro validação interna sistema de mensagem.Envie novamente!)
status de comunicação do sistema : 0 (Enviada ao sistema de menssagem (XI,...))
status do sistema de mensagens : V (Mensagem Recebida: Erro de Validação Interna)
Sem utilizar o botão Reset NFe, clico no botão Request Cancelation e realizo os procedimento de cancelamento.
Verifico pela tabela /XNFE/NFE_HIST que gerou um registro com a chave de acesso, type 3 (Inutilização) e status 6 (Enviado ao Processamento da Nota Fiscal Eletrônica).
Consulto no SEFAZ e verifico que essa nota já esta inutilizada porém na J1BNFE a nota continua processando.
Alguem sabe como resolver este problema?
Obrigado,
Leandro Von Zubem.Bom dia.
Tenho uma NF-e que está em situação parecida e agradeço suas colaborações.
Estamos na ECC 5.0 SP 19.
Esta NF-e foi rejeitada pela SEFAZ (NF-e writer e o erro estava no ano da data de emissão = 2008)
e o usuário não percebendo tentou re-enviar várias vezes.
Por fim, mesmo Rejeitada foi solicitado o Estorno (Skip) e os status da NF-e ficaram como abaixo:
SAP ECC 5.0 SP19
Status Ação : Em processamento
Status do documento NF-e: 2 Rejeitado
Status de comunicação do sistema: 3 Rejeitado/a & autorização solicitada para ignorar
Status do sistema de mensagens: C Mensagem recebida: pedido de inutilização
NF-e Código de Status : 228
Log
Novo stat.comun.sistema "Rejeitar estorno/ignorar usuário aceitos" não permitido p/status
comun.sist.anterior "Rejeitado/a & autorização solicitada para ignorar
Nº mensagem J1B_NFE007
GRC
Status Code: 228 Rejeição: Data de Emissão muito atrasada
Seguindo as orientações já mencionadas aplicamos em Desenv as Notas 1376901, 1376324 e 1298283 e
simulamos a situação. Mas a NF-e também permanece "em processamento".
A Nota 1141636 não foi possível aplicar porque exige para Basis o SP 700 e estamos no SP 640.
Esta atualização seria muito mais demorada.
Pergunto: existe alguma forma de ajustarmos os status para finalizar esta NF-e? (Rejeitar ou Aprovar/Rejeitar).
Agradeço a toda colaboração.
Abraços a todos e ótimas festas.
Luis Appel -
My Iphone 4 does not come with a SOFTWARE UPDATE option.
My partner bought my iphone 4 version 4.2 about two years ago from a well known store. He got himself one at the same time but i cannot update mine because it does not come with an option in settings, general that allows me to update it. All of my apps are useless as they need at least iSO5 to run. I cannot check my bank accounts or anything. I have rung and spoke to apple many of times and followed all the steps to try and update. As this is not my fault and the iphone had not been loaded with the correct software there should be something APPLE could do free of charge!!!! I really need help as i cannot afford a replacement or want one. I just dont know what to do anymore!!
Hi there wishheartgirl,
You may find the information in the article below helpful.
iOS 4: Updating your device to iOS 5 or later
http://support.apple.com/kb/HT4972
-Griff W. -
Hello i have what I think is a first generation Ipod touch which did not come with the App store already downloaded onto it, can I not download apps to my Ipod touch?
If you have a 1G iPod you can update to as far as 3.1.3. Yu get hat paid update here:
Purchasing iOS 3.1 Software Update for iPod touch (1st generation)
You can identofy your iPod here:
Identifying iPod models
What iOS is curently on your iPod (Setting>Genral>About>Version) you need as lest 2.0 for apps but most apps need 3.0 or later. -
HELP NEEDED!! Recently upgraded my ipad air to the new update, charged it over night, now it will not come on? i plug in the charger but comes up the normal charging sign but still no life in it? Seems as though theres either a problem it charging or starting up. Had the ipad for about a year and a month or 2.. what can i do to source the problem?
Its just started up with the apple sign, then it goes to an off black coloured screen so its on but nothing showing just a dark screen but not jet black.. ahhh help!! thank you in advance
-
Itunes will not come up on my computer
itunes will not come up on my screen. It shows up in windows task manager. When I click on the desktop icon, it flashes off then back on again, but itunes doesn't come up. Quick-time comes up when I click on the icon. itunes shows 44,540 on the Mem Usage column on the Process tab of Windows task Manager. I don't know what to do next. When I click on a song from my "My Music" folder under itunes library, it won't play. I'm out of ideas
If itunes.exe stays in task manager there are a few things to try. Easiest one is to start itunes and hold down the shift key until iTunes starts. Choose "Create new library" when prompted.
If itunes.exe just flashes briefly in task manager, I believe in the past that indicates malware on your PC. -
ipad does not come on once its unpluged from power source,it enters recovery mode when both power and home botton are pressed with usb on powersource but does not come up at all when connected to computer or out of power source
What model iPad do you have? If it's an iPad 1, the battery may have expired and needs replacement.
Cheers, Tom -
Monitor does not come out of sleep Mac-Mini Mini-DVI to Dual DVI-D cable
I have an August 2009 Mac-Mini that I'm using with an Apple supplied Mini-DVI to DVI adapter along with a DVI-D Dual Link Cable connect to a Sceptre X7XV-Naga+ LCD monitor.
The monitor is going into sleep mode on its own with no way to disable this feature on the monitor itself. I've disabled sleep mode on the Mac-Mini in the power setting in System Preferences.
When in sleep mode and I move the mouse or press a key, the monitor will not come out of sleep mode. From other posts, I read that the issue might be that I wasn't using a Dual-Link DVI-D cable, so I bought one and installed such a cable. That has not resolved the problem. The monitor will not come out of sleep mode. When I have the monitor connected with a mini-display port to VGA adapter instead of a DVI-D cable, it will come out of sleep mode every time.
Message was edited by: Annorax64I know it's a year later, but I'm not finding much through search.
I have the same exact problem. Difference being I'm using an iMac with 10.7.5.
Same video board and monitor - ATI Radeon HD 6750M video card connected via DisplayPort to Samsing S24A850DW.
I've tried two different mini-DisplayPort to DisplayPort cables and no change.
I think I read that 10.8.3 might fix the issue. Anyone that can confirm that, or has another solution? -
I performed sync and back up of iPhone 4. Then connected new 5s, followed instructions to restore using iTunes. My apps did NOT come through. Please help
Follow the link
http://support.apple.com/kb/HT2109
Maybe you are looking for
-
IPhone - Support for wired remotes
I have been looking all over the place for a wired remote for the iPhone 3G with no luck (and yes I have looked through this forum for an answer before asking my question). I have attempted to use three wired remotes from my previous iPods, but two o
-
Cannot post Goods receipt in MIGO Error message"Field Business Area requird
Hai I am posting Goods Receipt ( MIGO) with Reference to Purchase Order its having 47 Line item material. When i will doing Goods Receipt with rreference to po number its triggered error message in :Message No F5808 Field business Area is a Required
-
Printing even borders / margins from PDFs created in Indesign
Hi, I am having trouble printing images with even borders / margins - from my Epson R2400 inkjet printer. In Indesign I have set all margins to 5mm along all edges. Then I export the document as an A4 PDF. When I open the PDF using Acrobat, the margi
-
i want to create report in Oracle D2k (Reports 6i). Please help. i have 3 tables. 1 master table: school with school_id primary key 2 detail tables: dept & employee with school_id foreign key in both Now I want report like this: 1 Delhi Public School
-
Change Initial Page of E 6.0 SP14
Hello, we want to change the initial page of the EP 6.0 SP14 (http://<host>:50100/irj/portal). We want to change the image, disable the "Register now", I mean the anomymous user, and the disable the support page. How can we d this? Is there I iview o