MSE 8.0.110 not showing clients in NCS 2.2

Hi all,
I have established a LAB in my office which includes WLC 5508 (8.0.110), NCS VM 2.2 and MSE VM 8.0.110.
Every device/appliance is connected and associated with each other. However, I cant see clients on NCS floor maps. I am also trying to do Wireless Calibration but I am assuming if I can't even see clients on the map, I am pretty much not going to get the Calibration done as well. I can see clients connected on my WLC and NCS but unable to track their location.
Since I am using evaluation copy of MSE, I have installed all the services on MSE.
In the show auth-list at the controller, I can see MSE MAC Addresses and Key Hash, which I think is all thats required on the controller.
Any ideas where I can further dig up?
The client (my laptop) supports CCX v5. I can verify the same thing on WLC and NCS. However, in NCS, when I look up the MAC Address of my laptop, under CCX Capability Information I see Client Status "Failure".
Thanks in advance,
Jay

Prime Infrastructure 2.2. needs to reach WLC via SNMP. Is this configured?
On Prime go to:
Services -> Mobility Services -> Synchronize services. Select Your maps, click on "Change MSE assigment" and assign Your MSE.
Click on controllers tab on the right, select Your WLC, click on "Change MSE assigment", Select Your MSE and click "synchronize".
Go here: Services > Mobility Services Engines > mse> System > Status > NMSP Connection Status > NMSP Connection Status Details . Please check, is NMSP Status "Active" ?

Similar Messages

MSE Not Showing Clients After Upgrade to 7.6.100.0

I've upgraded our 5508 WLC's to ver 7.6.100.0. I've also upgraded our NCS to 2.0, and our MSE to 7.6.100.0. I now can no longer see clients on the MSE map for our sites. I've added the WLC to the MSE syncronization. When I select "show clients" it says 0 of 0 found. I know I have clients connected, since I can see them in the WLC. Is this a licensing issue? Thanks for your help!

Make sure that NMSP is up.
http://www.cisco.com/en/US/products/ps9742/products_tech_note09186a0080bb497f.shtml#add-va-ncs
On WLC console, use the show auth-list command.
The following example shows from WLC console that there is no location server available:
In order to manually add the MSE and establish a NMSP connection to WLC, complete these steps:
On the MSE console, run the cmdshell command, and then the show server-auth-info command.
This example shows the MAC address and the keyhash to be used for adding to the WLC.
Run the config auth-list add ssc command, and then run the show auth-list.
This example shows that the MSE was added to the WLC (manually).
On the NCS, confirm that the NMSP connection shows Active.
Sent from Cisco Technical Support iPhone App

802.1x WLAN auth not showing client ip in win 2008 AD security log

Hello.
I have a ongoing project configuring a cisco wlan with 802.1x, where microsoft network policy server is used for radius authentication.
Configuring the SSID on the WLC, and the 802.1x on wlc/radius server works fine, users type in their username and password on a smartphone/ipad etc and get access to the network.
The problem im facing is that I want to log the clients ip-address on the radius-server security log, so I can use cisco active directory agent to find the ip against username mapping in ironport.
The active directory agent checks the domain controllers security log to see what ip-address belongs to which user. In this scenario the user is mapped to the wlc ip, not the smartphone/ipad. The result is a lot of users mapped to the wlc ip-address, and the logs in cisco ADA/ironport is worthless.
Is there any way to configure wlc/802.1x to send the actual client ip-address to the authentication server, and not the WLC?

Please configure radius accounting on the WLC to have the required logs on the NPS server.
On the WLC, make sure we have radius accounting server configured under security > AAA > radius > accounting
After that Go to WLAN, edit the WLAN > security > AAA server and enable radius accounting.
Radius accounting on NPS logs
http://technet.microsoft.com/en-us/library/dd197475%28v=ws.10%29.aspx
Regards,
Jatin

2504 GUI not showing clients connecting at 5Ghz

Hi all
Recently upgraded our infrastructure to v8.0.100.0, on the 'new' landing page, the GUI is showing no clients connecting on 5Ghz, only on 2.4Ghz.
If I check from the CLI, there are clients connected on 5Ghz.
Is anybody else seeing this?
Is it just a 'bug' (does anyone know)?
Please see attached.
Cheers

Hi,
I test your scenario and showing as it should be.
MAC Address AP Name Slot Status WLAN Auth Protocol Port Wired PMIPV6 Role
48:43:xx.xxx.c3:92 AP001 1 Associated 3 Yes 802.11a 13 No No Export foreign
check the screenshot:
Regards

9iR2 DB auditing is not showing clients IP address

Friends,
OS: RHEL AS 3
DB: 9iR2 (9.2.0.4)
init.ora - audit_trail = true
when i execute the below query...its return empty....
select sys_context('userenv','ip_address') from dual;will the above query work in 9i db?
how can i get the client's ip address, who are all connecting to the db?
thanks

Hi,
You can use the query below;
select utl_inaddr.get_host_address(host_name), host_name from v$instance; For more details please visit the linkl below;
http://asktom.oracle.com/pls/asktom/f?p=100:11:0::::P11_QUESTION_ID:10583864460294
Thanks and Regards,
sskak

FlexConnect Local Auth. Usernames not showing in WLC/NCS

Hi,
I am working on a new install where the customer is using local RADIUS servers at each of their many campuses
(for local dynamic VLAN assignment), while using a single set of controllers at the core of their network.
For the record, we have set up a pair of 5508s (v 7.2.103.0) in their central data center with 3602i APs around the various campuses. We are using FlexConnect groups to locally authenticate and switch the users.
Right now, the config is working great as far as authentication and local switching goes. The problem we are experiencing is that none of the authenticated usernames are being passed back to the controller (and ultimately NCS). This makes the tracking and troubleshooting of users difficult. Is there something I am missing here? I can't seem to find any fixes relevant to this issue in the 7.2.110.0 release notes.
Maybe I am going about this wrong. I am very open to alternative solutions.
Thanks.

After discussing this issue with local Cisco folks, TAC and colleagues, it seems that locally authenticated user names are not passed to the controller (or NCS). It's not a bug, it's just the way it is.
If you want the AP to authenticate and locally switch users while communication to the controller is down (i.e. loss of WAN link), no usernames are sent to the controller for logging or troubleshooting... even when AP to WLC communication is working fine. It's a trade-off of information (usernames) for uptime.
If any Cisco wireless development folks are browsing, consider this a 'feature' I would like to see. Thanks.

MSE 8.0.110.0 not showing any clients

hi all,
i just posted a reply in some other thread stating the same thing but decided to make my own topic.
set-up:
2x5760 running 3.6.0
mse appliance running 8.0.110.0
prime infra in VM running 2.2
ap - 3702I / E
problem:
wireless clients not showing on the prime floor maps.
what have done so far:
wlc synced with mse thru nmsp - check
wlc added to prime - check
mse added to prime - check
mse synced with wlc thru prime - check
all aps positioned on the maps - check
CAS enabled on mse - check
NTP configured to wlc , mse and prime - check
check time all synced
nmsp status in mse - active
nmsp status in wlc :
WLC1#show nmsp status
MSE IP Address   Tx Echo Resp Rx Echo Req   Tx Data     Rx Data
x.x.x.x      618           618           43878       10
WLC1#show nmsp subscription sum
Mobility Services Subscribed
Server IP         Services
x.x.x.x       RSSI, Info, Statistics, AP Monitor, Attachment, Wired Location
WLC1#show nmsp subscription deta
Mobility Services Subscribed by 10.29.220.9:
Service         Subservice
RSSI            Mobile Station, Tags, Rogue
Info            Mobile Station, Rogue
Statistics      Mobile Station, Tags
Attachment      Wired Station
Location        Subscription
AP Monitor      Subscription
troubleshooting done so far:
deleted then added mse on prime then resynced to wlc
reconfigured nmsp on wlc and resynced again with mse
rebooted mse - no avail
rebooted prime - no avail
reboot wlc - not an option coz theres a lot of users =)
tia,
chris

Thanks Pete, I have done that, in fact I used a useful utility to update that property on a batch of servers.
Thanks for the thought, any additional ideas?
Cheers
Andrew

Why does mail sent using the MacOSX mail client not show up in my sent folder when I access my Gmail account in a browser?

I've recently started using my first Mac, and I hooked my work email (Forwarded to Google Mail) and my personal email (Gmail) into the MacOSX mail client. Everything seemed to be going smoothly, until I noticed that sent mail from my work email through the MacOSX Mail client is not showing up in my sent box on any other clients. Sent mail does show up in my personal email in Gmail, though.
Can anyone help me understand why mail sent from the MacOSX Mail client doesn't end up in the sent folder of my work Gmail account? I suspect it has something to do with the forwarding-to-Google process -- a sort of "too many cooks in the kitchen" situation. Has anyone heard of this problem before? What should I try?

I've been noticing that too. Just told me there were 6 outgoing messages, even though I did not create any new messages.
One hypothesis is that it's generating those messages when a rule moves an email from one folder to another.
Can someone at Apple confirm this?

Photo Uploaded in AD but not showing/visible in Lync 2010 client

Photo Uploaded in AD but not showing/visible in Lync 2010 client
bala

Hi,
Please also double check the size of the photograph in AD, make sure the size not overtake 48 pixels by 48 pixels, as it has a serious limitation on the size and resolution of the photos: the thumbnailPhoto attribute can only hold a photograph with
a maximum size of 48 pixels by 48 pixels.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

Outlook 2010 contacts not showing phone number in Lync 2013 client

Hi,
We have Lync 2013 with Exchange 2010. Recently we started upgrading Lync clients from 2010 to 2013.
A few users started reporting that their local Outlook contacts does not show phone numbers in Lync 2013 (working with 2010)
I have installed the august patch which should solve this issue
981751 - Lync 2013 does not display telephone number of an Outlook 2010 contact in the contact card
Any idea where to look next?

Hi Tobias Borgen Nielsen,
Lync expects all the phone numbers to be in the E.164 format, meaning they should be +1-111-11111111 etc. If they’re not like this, you will have to normalize them if you want Lync
to publish them.
The related article for your reference.
Lync not populating contact cards phone numbers from Active Directory (Or: How to normalize AD phone numbers for Lync Server 2010 and 2013)
http://y0av.me/2012/02/23/normalize_ad_numbers/
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or
suitability of any software or information found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Hope it can be helpful.
Best regards,
Eric

"Enable distribution-point sharing for this source site" did not showing SCCM 2007 DPs as SCCM 2012 content shares for CM12 clients

Hi
We have one central site server and three primary site servers in SCCM 2007 and completed the SCCM 2012 migration as single hierarchy.
During the migration, We have configured SCCM 2007 Central site server as source hierarchy for data gathering process and configured the "Enable distribution-point sharing for this source site" to make SCCM 2007 distribution points
as SCCM 2012 content shares to serve SCCM 2012 migrated clients. Now we are facing a problem that one of the primary site server's data gathering process did not gather SCCM 2007 DPs even though we configured "Enable distribution-point sharing for this
source site" but data gathering process is completing successfully.
Is anyone have idea, why these SCCM 2007 DPs did not appearing as SCCM 2012 content shares under "Shared Distribution Points"
Thanks in Advance
srkr

Now we are facing a problem that one of the primary site server's data gathering process did not gather SCCM 2007 DPs even though we configured "Enable distribution-point sharing for this source
site" but data gathering process is completing successfully.
Earlier all the shared DPs are showing under Shared Distribution Points ? Or since starting itself these DPs are not showing down? Have you checked migmctrl.log for some clue?
Anoop C Nair (My Blog www.AnoopCNair.com)
- Twitter @anoopmannur -
FaceBook Forum For SCCM

WRT160NL DHCP reserved clients are not showing up in the DHCP Reservation window.... Why?

I have 5 computers linked to my router. 4 are hardwired and I set it up so that each of the 5 has it's own static address. One of those computers is my DVR security camera system so can monitor my cameras remotely. It was working fine for years and now I can't access the DVR remotely anymore. I notice in the router Setup that the DHCP clients are not showing up as active even though two of the computers are on. I am running XP Pro on these machines and I can PING between them so I know some communication is going on. Also I can access the DVR cameras from my main computer using the internal IP address I assigned to the DVR, but not if I try to use my current WAN IP address.
Would appreciate any advice on troubleshooting this problem.
Thanks
Solved!
Go to Solution.

It may have something to do with the firmware of the router. I suggest you should do that. The firmware that you can download from the Linksys website is version 1.0.0.3 Build 2. (http://support.linksys.com/en-us/support/routers/WRT160NL). After the upgrade, reset the router to factory settings (pressing and holding down the reset button). It is best to re-configure the router from scratch also. Try to power cycle your whole network as well.

Clients not showing up

Hello,
I am new to Flash Media Server. I have FMS v2 installed and
running. I have a flash application that posts some data (tracking
information) to the FMS Server whenever a user tries to play
anything using the flash application. The flash app sends data on
port 80.
This used to work till recently when we did a server move and
after that it stopped working. I dont see any errors anywhere. Log
files, event viewer, everything is clean. The FMS server is running
on a specific IP and the ports 80, 1111 and 1935 are opened up.
I dont see clients in the FMS admin console. Does that mean
the client connection is getting rejected? Or does that mean that
the flash application is not even connecting to the Flash Media
Server? How do I troubleshoot the connection issue? I am kind of
lost because, there are no errors on the server side but the
clients do not show up!
Please advise.
Thanks,
Satya

Since the issue is new since the server move, my first guess
would be that either something is getting in the way of port 80
(assuming all client connections are failing), or you're not
allowing clients to use RTMPT when needed (assuming only some
connections are failing).
If the URL argument in your client side
NetConnection.connect constructor explicitly defines port 80, the
flashplayer will try only port 80 using the protocol specified in
the URL string. If you do not define the port, and you define the
protocol as RTMP, the flashplayer will automatically try various
combination of ports and protocols if RTMP:1935 fails.
About this new server, is it Windows or Linux. If it's
windows, and you're running IIS 6 on it, did you unbind IIS from
the IP FMS is running binding to? I've found that in most cases,
IIS usually grabs port 80 (on all IP's) before FMS does. A quick
run of Netstat should tell you which service is bound to port 80 on
the FMS ip.

WRT54G v6 client table not showing wired clients

I have a WRT54G v6 using the lastest firmware. Is there any 3rd party software that can display what clients I have on my network? The reason I'm asking is because my router will only show the wireless clients and not the ones connected on the wired side. Other than that everything works fine.

I have similar problem. DHCP client table shows only wireless laptops using dynamic ip address. All my wired destop (dynamic ip), and other static ip devices both wired or wireless do not show up in DHCP client table. Any idea? I have v8.

Crystal report viewer do not show on client computer installation

hi
hope all you are fine
i develop a simple project that show "Hello word My First Crystal Report" on crystal report viewer. after this i add new project "setup and deployment". In Setup Project I add 4 files of .msm for show crystal report.
1. CRRuntime_13_0_tr.msm 2. Microsoft_VC100_ATL_x86.msm
3. Microsoft_VC100_CRT_x86.msm
4. Microsoft_VC100_MFC_x86.msm 5. Microsoft_VC100_OpenMP_x86.msm
when i install on developer computer. it runs successfully. when i install on client computer, software runs fine but crystal report did not show and having error "METHOD NOT FOUND VOID CrystalDecision.WINDOWS.FORMS.CrystalREPORTViewer.SET_CACHEDPAGENUMBERPERDOC(INT32)"
i install .net frame work and CRforVS_13_0_9.exe on client computer but .net frame work show form but crystal report did not show.
Please Help

Hello,
For Crystal repot related question ,please consult on SAP Crystal report forum instead of here.
Best regards,
Barry
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

MSE 8.0.110 not showing clients in NCS 2.2

Similar Messages

Maybe you are looking for