MSI-180: Radio is very quiet

Hello
I have the following problem with my MSI-180: The volume of the radio is very quiet. The volume level is much lower than for all other devices (like DVD, TV, etc). Even setting the volume of the Mixer in Windows to max is not enough to ajust the different volumes.
Is there any possibility to arise the radio volume (registry, etc.)?
Thanks for your help
Patrik

Picture Quality
Composite -ok
S-Video - good
Component RGB - very good
VGA - better
DVI - best
so S-Video will not give you the best picture quality. it has nothing to do with the drivers.
how does the picture look on your VGA/DVI monitor?

Similar Messages

  • [solved] Sound very quiet

    Sorry, already solved.
    "amixer set Front unmute 100%" fixed the problem. Strangely enough, i muted and unmuted each and every playback device via alsamixer many times.
    If you have similar problems try these three commands:
    amixer set Master unmute 80%
    amixer set Front unmute 100%
    amixer set Headphone unmute 100%
    Hello,
    my sound is very very quiet. To hear something I have to turn my amplifier up to at least 1/2 volume. At that volume level it would usually be enough to be wake the neighbourhood.
    I checked with alsamixer if the sound output was muted but it isn't. What's strange is that the sound output worked just fine today but a restart suddenly the sound was very quiet like this.
    Any ideas what's causing this?
    Mainboard is MSI H55M-ED55 with sound chip ALC889.
    06:53:26 ~ > cat /proc/asound/cards
    0 [Intel ]: HDA-Intel - HDA Intel
    HDA Intel at 0xfbdf4000 irq 22
    Last edited by demian (2010-02-08 06:01:55)

    Hi Charrison21989,
    Welcome to the Apple Support Communities! I understand that you have been having some issues with the audio quality coming from the receiver on your iPhone 5. I suggest going through the steps in the following article to try and isolate and resolve the issue.
    iPhone: Receiver and call audio quality issues
    http://support.apple.com/kb/ts5196
    I hope this helps,   
    -Joe

  • MSI 180 - Graphic driver problems

    Hi folks,
    after cooling down my Mega 180 from 48 degree to 34 degree start-up-termperature  (heatsink lapping, turn fans around, build in a fresh air duct for cpu fan) my system is running very stable - what a great lap forward after days full of frustration. Thanks to live update I have the newest bios (rev. 3.5) and drivers for my hardware installed. But I'm still facing some smaller problems, maybe is this forum I can find a hint how to handle that:
    1.) TFT-drivers not accepted
    I'm using a Hyunday Q17 TFT display and I never had any problems with my old system to identify this correctly. But with my MSI 180 XP installed 5 (!) default displays and will not accept the correct monitor driver I have. When I try to delete 4 of this 5 from the control panel XP re-installs them during the next boot-process. My question is: why 5 displays and why just default displays??
    2.) Flickering and coloured stripes after booting
    Sometimes, when Windows is alreday started, the display changes from the "Welcome"-Screen to some colourfull stripes and seems to be frozen. After hibernating and re-starting everything is o.k.again. Diver bug ?
    3.) Black screen
    When entering the windows desktop, the screens turn black for 1-2- seconds, then again it show the desktop, then again 1-2 seconds black. It looks like the driver tries out various video modes. But I don't know why ???
    Conclusion is, that there seems to be a bug in my graphics driver. I tried to load the newest once via Live Update, then again directly from Nvidia website, but nothing changed. Any ideas about that ???
    Any hints for me ?? Thankx in advance
    Flo

    Thank you for your reply. I think, i should try to describe my problem more clearer :o)
    I'll check later, when I'm back home, in Nvidia driver are installed properly. I just checked, if there is a question mark somewhere in system control panel resource overview.  But everything looks fine.
    The flickering is a little bit more tricky: When starting the PC instead of my windows desktop a colorfull page of thousands of colourfull stripes appears and flickers like a rainbow. Windows is definitively running, I can can use all keyboard short cuts e.g.. It is not the type of flickering when running under low frequency. Maybe this, comnined with 2 seconds black display, is part of the famous "black display" issue.
    My last machine was able to identify my TFT correctly as a Hyundai Q17. But at that machine it was connected by DVI, not the analog connection. Maybe that is my problem. I'm still looking for a small graphics adapter with digital out (nothing special, I'm really happy with the onboard graphic controller, I'm not a gamer), I'm afraid my old fullsize FX5200 might be too large for the Mega.

  • MSI 180 Skystar 2 ImageQuality S-Video

    Hi,
    I`m using a MSI 180 with 512 MB RAM and a sempron 2400. Moreover, I installed a Satcard (Skystar2). I use the onboard Graphiccard.
    When I watch TV with ProgDVB, the Imagequality is obviously not as good as with my Sat-Receiver. (I can directly compare because the Sat-Receiver is connected to the TV too. The 180 is connected via the S-Video out to my TV. I tried several option/Adjustements in the Nvidio-Driver. But it seems to me that the image is kind of smoother. For example, a newschannel with a small Newsticker in the bottom of the Image.  With my Sat-Receiver, it`s very good readable and very clear. But with the MSI, it`s hard to read, smoother and not clearly. I also tried several Video.Filters (Sonic, Intervideo, Cyberlink,...), but no serious changes.
    I hope someone can help me!
    Thanks for your help in advance!

    Picture Quality
    Composite -ok
    S-Video - good
    Component RGB - very good
    VGA - better
    DVI - best
    so S-Video will not give you the best picture quality. it has nothing to do with the drivers.
    how does the picture look on your VGA/DVI monitor?

  • Airplay volume very quiet with Pioneer amp suddenly.

    I have a Pioneer VSX-2021 amp which has built in airplay.  I'd been using it for several months with no problems now suddenly it is very quiet.  I have to turn the volume up to maximum to just about hear the song that is playing.  The amp volume is fine for everything else (internet radio, films, CDs etc) airplay is the only thing is effected.  It is the same if I airplay from my phone or from itunes the volume is too quiet.  I've been searching all over for why this is happening but it seems no one else has this problem.  I can't understand why it is so quiet as it all used to work fine and at normal volume.  Anyone else come across this problem or have an idea how to fix it?
    Just to reiterate:
    1. Used to work perfectly from itune or iphone
    2. Still plays fine from iphone or itunes just increadable quietly
    3. Amp volume is fine for any other input including playing songs from dlna server and internet radio

    This problem has been resolved by doing a factory reset of the VSX-2021 amplifier.

  • Very quiet constant beep on forced shutdown

    I dont know what just happened - but on startup my mouse froze and the puter hung - i couldnt even ctrl-alt-del.  So it used the reset button, that didnt work so i hit the off switch until it shut down.  After the fans had stopped i was aware of a very quite constant beeping that definately came from the computer - where i dont know and i certainly didnt recognise it as an alarm from the motherboard like what you get when the chip is getting up to temp or something isnt right at boot-up.
    Would anyone have any ideas as to what it was as im sure it is related to the system hanging.
    regards to you all

    Quote
    Originally posted by labtech1
    The bios version you are using has a bearing on whether the cpu temp is acceptable or not so perhaps you can add those details to your signature. As you mention the MSI chipset fan I assume that you have the K7N2 Delta-ILSR but please clarify. The reason why I mentioned the CPU Warning Temperature option  is it tends to start to operate below the setting in the bios in my experience of using the board. Raising it to say 63/66c should remove that as a possible cause of the beeping. The board will still shut down if the cpu reaches a critical temperature. It is just a warning beep.
    Hi Labtech, yes it is the ilsr and the bios is award 7.70.  I did an update last night on the PC Alert and since then its reporting 4 degrees cooler.  Ive not done the bios as there was nothing there in the fixes that I thought related to me and ive heard that with bios unless there is something to fix dont fix it.  I will though flash it if you advise me to.  
    Although I know what was causing the warning beep, i still havent found out what or even where this other very quiet beeping came from on the board.  Im convinced though it was not a bios warning beep like the one we have been talking about with regard to the cpu temp.  That is unless you great techies can tell me otherwise (cos im still worrying about it even thought it hasnt happend again )

  • Very quiet sound in my Lumia 620

    Hello,
    I have a problem with a speaker to talk in my Lumia 620. I have installed Windows Phone 8.1. When I bought this phone sound from this speaker was loud but now after few mounths it is very quiet. My volume is set for max. What to do with it?
    Please help.

    With WP8.1 there are separate volume controls for different functions .. Hope you are setting them correctly ..
    See THIS

  • Bluetooth iPhone 4s car stereo very quiet

    Hi everyone, I was wondering if someone could help me with an audio problem. Sometimes when I connect by iPhone 4s to my car stereo via Bluetooth, the audio is very quiet. Even with my volume turned all the way up on my phone and car stereo. Then other times ill connect them and it'll play normal and very loud. And way to fix this so it's loud all the time?-(when's it's quiet I turn it all the way up and it's still like background noise...)
    TIA

    I have the same problem with my iPhone 5S in my Subaru.  Until someone can offer a fix, I am resorting to using FM, only.

  • Incoming ichat convo very quiet

    Hey Guys,
    Just trying to get a podcast going in GB3. Myself and a buddy are audio chatting on ichat, except he comes in quiet on my end. I have to turn up my system volume to a good 3/4 of the way to hear him properly.
    When trying to import into GB3 i hit the record button, the import ichat convo window comes up and we each get a track... but i am on both tracks... and so is he... but he is very very quiet. Now if we could get eachother on seperate tracks (like i thought would happen) i could probally boost the track volume of his track to make his volume slightly louder, but chances are it will be still on the quiet side.
    He is using a usb mic and i am using a line mic through a small mixer. We are both on powermac G5s.
    Basically how can i boost his volume on my end and how can we be on 2 seperate tracks in sound as well as the screen?
    Thanks in advance
    Ryan

    all the volumes are cranked on his end... and its still coming in quiet in garageband on my end... and its still doubling the voice tracks on each indivisual tracks.
    he trid on his garageband on his end (GB2) and its coming in loud and as it should....
    anyone have any ideas?

  • Very Quiet Audio During Playback

    Hi,
    Just trying out my iPod 5G and an Apple AV cable.
    Video is fine but audio is very very quiet. Have to have the iPod set to virtually full volume and TV up to about 50 (normal volume on TV is 12-15) to get anything like listenable audio.
    The videos are fine through headphones with sound when volume is set to approx 25%.
    I am using Handbrake on the Mac to encode into MPEG-4 format.
    Any ideas ???
    Regards
    NIALL 8-)
    iPod 5g 60gb Firmware 1.1.1

    This is the way it works for everybody, your unit is not malfunctioning.

  • Sound is very quiet !

    Hi
    I recently bought a zen mp3 from 32 GB
    but now I've put some songs on it and the sound is very quiet, even when I put it on 25 !
    my brother has a zen mp3 of 8 GB and his sound is very loud at 25.
    Does anyone knows how i can get the songs to play louder?
    thanks
    sjesches

    Hi,
    I had a similar problem with my ZEN, the sound was just too low for my requirements as I listen to it a lot along busy roads where there is a lot of noise. I assume that you have the European firmware on your ZEN, check it, the European firmware ends in an "e". If so, you might try downloading and installing the US firmware which you can download from the US site. Download the US firmware first before throwing out the European firmware, then install the US firmware. This is much louder than the Euopean firmware, I believe this is because in Europe the authorities want to protect their young people from ruining their hearing and therefore restrict the volume of players.
    Now that I have the US firmware on my ZEN I have no problem with the sound anymore.
    Have fun with your player!
    macqueline.

  • TS1630 ringtones on my iphone 3gs are very quiet volume at max

    I have recently been given a iphone 3gs. Everything works fine except the ringtones and alerts are very quiet. I have turned up the volume to max. but this has little or no effect. Any help would be appreciated otherwise I have a phone which is of no use because I can't hear it when someone is calling!!!!

    iPhone: Can't hear through the receiver or speakers

  • My guitar is very quiet when trying to record? How can I make it louder?

    I just got a new iMac and am using GarageBand to record some guitar and it is very quiet even with everything maxed out (gain and volume on focusrite saffire pro 14, track and master volume, and amp sim volume). Is there anyway to make it louder? Chain is Fender Deluxe Lone Star Strat > Saffire Pro 14 > FireWire cord> iMac. Thank you.

    Hi The App,
    When you're plugged in, does the light that says "Inst" light up on the PRO 14?  This indicates an instrument level input, and can be activated through Saffire Mix Control.  Near the bottom of the window, make sure the channel your guitar is coming in through has "Inst" selected, rather than "line" (also make sure you turn down the gain before you do this).  Let me know if this solves your issue.
    Best Regards,
    David Tichauer // Focusrite Technical Support

  • Voice Recordings come out muffled and very quiet.

    The first few songs I made with my friends are clear and you can hear the voice perfectly and loudly. Now when I try to record voice its muffled and very very quiet no matter what. I've tried different voices, recording levels, but nothing seems to work. Does anyone know how to fix this? I don't think it's the mic because I can web chat fine.

    Are you talking about the iPod speaker? If so, does it work OK with headphones?
    There isn't much that you can do yourself to repair the iPod if there is damage inside.

  • 6230i suddenly started playing ringtone very quiet...

    Hi,
    I've got an MP3 ringtone, which used to work fine. All of a sudden, it's started playing very quietly for the first couple of seconds, and then gradually getting louder.
    I've got it set to maximum volume (5) and the "incoming call alert" to Ringing.
    Any idea how to get it back to ringing with some volume.

    Hi Kheldar
    Welcome to the Nokia support discussion boards
    The query you have has already been answered in the following thread
    http://discussions.nokia.co.uk/discussions/board/message?board.id=phones&message.id=39
    cheers
    Ajak

Maybe you are looking for