MSI 645Ultra and problem with memory.

Hello.
I have big problem with my mobo. I can't run 645Ultra mobo (MSI 6547) with other memory than installed actually. Now I have Samsung DDR333 128MB (one-sided), and everything works well. But I tried to install another modules (2 pieces - 256MB DDR266 double-sided). After install one of those modules, my comp doesn't start. Mobo only beeps and there has no signal on my monitor. With installed two modules - my memory (ddr333) and one of those 256MB ddr266, computer runs, but POST shows me only 128MB :(.
What is going on? Does this mobo supports memory other than ddr333 (user manual says - YES, but now I'm not sure).

"645 ultra" DDR Brands tested with this board
http://www.msi.com.tw/html/support/testreport/6547/memory.htm
ddr 333 what brand :O
ddr 266 what brand :O
DDR 266 aka 2100 Cant run at 333 aka 2700 ;(

Similar Messages

Problems with Memory on upgrading

Problems with Memory. I Dide not hace space to upgrade. Now i do, but It still cancels for lack of space

Actually, your problem does not sound like memory, but hard drive space. By default, you lose 10% of your drive to the OS and formatting. To tell how much hard drive space you have go to:
>Finder
>At the bottom of finder in the gray bar it will tell you how much space you have available on your hard drive.
Your hard drive should be no more than 85% full! If it is, delete, get a larger hard drive, remove items to an external drive.
GarageBand only needs 1.2 MB of space.
In order to use GarageBand, some additional content is required. If you do not already have the content installed, it must be downloaded.
Make more disk space available by moving some of your files to a different disk (such as an external hard disk or a USB flash drive), or by deleting files you don't need and then emptying the Trash

Strange problems with memory dimms(Banks) in imac 27in mid2010

Hello dear Apple community. I had a really strange problem with memory dimms(modules anyway)
I have one really good imac 27in with i7 but as you know after some years the lcd screen became yellowish and cloudy
So i decided to clean it as i have some knowledge and i did that to others lcd screens with success.
OK so after successfully cleaning and working like new ( i mean not the external screen with magnets but the lcd internally)i started it.
Before dismantling my memory was 16gb ( 4x4 dimms)
After starting it a strange problem arise without any reason! Memory reduced TO 8 GB!!!! memory banks on the right as we seeing it didnt worked at all
and it was not from dimms because i swapped them..!!!
So after a lot of thinking and asking tech guys to take a second opinion all the saying (including me that logic board failed for some strange reason.
Some days before i installed CCleaner and also Onyx because after a lot of installations and uninstallations my mac became a little sluggish..
I thought that some serious preferences files removed or some hardware settings deleted with Onyx ( is very good and powerful program that can fix the pc and also destroy it in a second) so i removed and reset all preferences. But nothing changed.. So i put a new hard drive and reinstall OXS to see if something can change.
After formating HD to appleHFS+ saw system profiler that still couldn't see all banks(16gb). I remove logic board and i put another processor i7 that i have as a back up and still nothing( some saying that only these 2 things must be faulty if memory banks not working , processor an logic board and sometimes reinsatlling OS can fix it as i mentioned before. But still nothing...
So from my nerves and after so much testings and no sleeping for 2 days as it was working i pulled off the memory modules from the right bank i put them again ( off course nothing changed) and i close it. After i restarted it like a miracle finally i saw that i have again 16gb in system profiler!!
Tech guys here please give me an explanation to this because i gooing crazy! What happened and after i pulled off the dimms while it was working the problem fixed?? It is not recomended at all this action. I forgot to mention that i did Apple hardware test and nothing found..
Sorry for long post.

Okay great news... My memory problems are solved and my Mac Mini is now running at 8 gigs of Ram. I tried the suggested DD3 1333 which the computer wouldn't even recognize.
So after visiting the Apple Store in the Fair Oaks VA shopping mall; they suggested that I try DDR3 8500 ram. I visited Micro Center in Vienna VA, and I purchased BGreg's Suggested Crucial Brand Ram. 10 minutes after I got home the Mac Mini booted on the 1st try with 8 gigs of Ram.
Some venting that Apple hopefully will read and mention to their resellers....
The people in the Apple section of MicroCenter in Vienna at first argued that the Mac Mini only supports 4 gigs. EVEN AFTER I SHOWED THEM THE SPECS on the Apple website. The clerk (who I am calling a clerk because by no means was he a "specialist") even suggested that the Apple site was wrong. On a later visit to MicroCenter to purchase the DDR3 8500, that the people at Apple recomended; Microcenter even suggested and argued that I needed DDR3 1333 and NOT DD3 8500. THIS WAS AFTER I TOLD THEM THAT Mac Mini WOULD NOT RECOGNIZE the DD3 1333 Dimms. Working in retail myself I don't go along with the concept that the customer is always right, however in this instance clearly I was.
I should point out that some of the staff in Microcenter really do try hard, however like with any business it only takes a few "know it all" bad examples to turn customers off.
Curious post thought; I wasted about $75 in gas driving to and from Microcenter because of their bad advice.

Any new about updating lion to 10.7.4 and problems with bluetooth devices like Bose Soundlink Bluetooth Speaker?

Any new about updating lion to 10.7.4 and problems with bluetooth devices like Bose Soundlink Bluetooth Speaker?

Monroe
Just in the moment i updated to lion 10.7.4 my Bose Soundlink Bluetooth stop working as good as it was. I´m gonna try the update in the Bose web page. I hope it works

Crackling, Left Rear Channel noise, IRQs, 4 Gigs of Memory, fixes and problems with XFi Fatal

Hello fellow troubleshooters. Well I've been working on my XFI issues since there are so many of them trying to make the one piece in my newly built system work as intended. I will put my hardware info below this post for comparison purposes if it helps you at all or for feedback/ideas. Well first off I had the crackling noise popping so on even when my machine was idle. If you have not done this yet do it
!!! Start, Control Panel, Sounds Speech and Audio Device, Change Speaker Settings, Advanced (in device volume), ok now there is a bunch of sliders go to "options" check everything, ok now that you see all the sliders mute Everything besides: Play Control, Wave, CD Player for testing purpose. You will probably hear a difference as you do it. Especially Mic 2. Ok well that issue resolved my popping crackling noises when idle. Ok so I still have a shared IRQ issue since I have an Asus A8N32-SLI Deluxe board and the slots go as such PCI-E, PCI, PCI, PCI-E, PCI. Well since the GeForce 7800 GTX cards I have take up not just the PCI-E slot, but also the PCI slot is covered from the Huge Fan. Then the Same thing for the Second graphics card. So I have only one slot that works for my PCI Fatalty sound card. Well this forces me to share PCI IRQ between one of the Video Cards and the Sound Card. Its not a "conflict" it is simply sharing the IRQ, after the above issue fixed my popping issue this no longer was a concern. Now my big issue is that I sent my Sub Woofer in for RMA, I have the Gigaworks S750 7. THX speakers, they are great but when I really crank up the volume on them I would get the sound like a speaker was blown in the left rear channel, so I swapped another speaker in its place and I have the same problem. So the RMA folks said to send in the Sub Woofer which cost me over $30 to ship the thing only to have them tell me there is no problem. Well I had recently done RMAs on my sound card, both Video Cards, and my mother board too in hopes of fixing the next problem. So everything is new though I got a refurb on the mobo. So I'm just waiting on my Sub woofer now so I'm using my headphones and guess what I'm finding there is this noise in the left speaker, an issue I sent the headphones back for a long time ago when I was using them waiting to buy my speakers. I have the Creative Pro Gamer headphones. So now I read a post about someone else with the same issue left channel, and I have to wonder I am not alone and that usually means in Creative Labs land there probably is others with this issue that have spouses that wont let them stretch their audiophile legs with extreme volume, if this is you try it out kick up the bass, and see if you have this problem too, if so please post it here. I have no clue on this one and I am open to any ideas. Ok and the last issue!! This is the real problem I'm facing now. I play EQ2 I love my MMO titles with the occassional single player title for those short stints at the computer between work, parenting, and stuff my wife demands be started before she finishes speaking of it (those of you married know what I'm talking about). I have 2 operating systems, XP Home, and XP Pro 64. Home I use for Office, graphic design, and general applications. XP Pro 64 I use purely for gaming. All my games are installed through this OS which is on my 2 74 Gig Raptors in Raid 0, I have another Partition for XP Home, and a 3rd for all the game installs. So I recently found that after selecting Extreme Graphics option in EQ2 then moving the rest of the sliders to Max that my G5 keyboard which has a performance monitor in it showing the amount of Ram usage showed me hitting about 90% and would spilke at the same time as I found I had frame rate slowdown. So I decided to get 2 more gigs of Corsair Twin XMS 3500Pro 024x2 memory bumping me up to 4 gigs. Well I had to go into the bios I found and change a memory setting to discrete and enable the memory hole in order for XP Pro 64 and the motherboard to see the memory. At this time I was working on other things with my computer, and suddenly the popping noise came back so I'm pissed now.... But oddly its not happening in XP home, only in XP 64. So I'm thinking I may have to go to XP home for my gaming OS, then just before I install home I remember that XP home wont register 4 gigs of memory.... So I go turn off the memory hole and discrete settings and this sets the memory to 2 gigs.... Crackling sound in ALL EAX GAMES goes away.... So now clearly my issue with my sound card and EAX crackling noise is Memory related somehow. Now I have isolated it to 4 gigs of memory, but it makes me think of those folks with this issue perhaps something is amiss with their memory and how it works with timing, or onboard memory on the sound card which is a first time memory is put on a sound card?.... Any input is appreciated as to how to repair this issue, thanks for reading, below is my system set up.
rocessor >
?Model:???? x AMD Athlon(tm) 64 X2 Dual Core Processor
??????4400+
?Speed:???? 2.2GHz
?Model Number:???? 4400 (estimated)
?Performance Rating:??? PR7072 (estimated)
?Cores per Processor:?? 2 Unit(s)
?Threads per Core:??? Unit(s)
?Type:????? Dual-Core
?Internal Data Cache:?? 2x 64kB Synchronous, Write-Back, 2-way set,
??????64 byte line size
?L2 On-board Cache:?? 2x MB ECC Synchronous, Write-Back, 6-way
??????set, 64 byte line size
?<Mainboard >
?Bus(es):???? ISA PCI PCIe USB FireWire/394 i2c/SMBus
?MP Support:???? 2 Processor(s)
?MP APIC:???? No
?System BIOS:??? American Megatrends Inc. 8.2
?System:????? System manufacturer System Product Name
?Mainboard:???? ASUSTeK Computer INC. A8N32-SLI-Deluxe
?Total Memory:???? 3.9GB DDR-SDRAM
?<Chipset >
?Model:???? Advanced Micro Devices (AMD) Athlon 64 /
??????Opteron HyperTransport Technology
??????Configuration
?Front Side Bus Speed:?? 2x 005MHz (200MHz data rate)
?Total Memory:???? 4GB DDR-SDRAM
?Memory Bus Speed:??? 2x 200MHz (400MHz data rate)
?<Video System >
?Monitor/Panel:??? Default Monitor
?Monitor/Panel:??? HP D895 HP P20 2-inch Monitor
?Adapter:???? NVIDIA GeForce 7800 GTX
?Adapter:???? NVIDIA GeForce 7800 GTX
?hysical Storage Devices >
?Removable Dri've:??? Floppy disk dri've
?Hard Disk:???? WDC WD2500KS-00MJB0 (233GB)
?Hard Disk:???? WDC WD3200JD-00KLB0 (298GB)
?Hard Disk:???? NVIDIA? STRIPE? 38.49G
?Hard Disk:???? Generic USB CF Reader USB Device
?Hard Disk:???? Generic USB MS Reader USB Device
?Hard Disk:???? Generic USB SD Reader USB Device
?Hard Disk:???? Generic USB SM Reader USB Device
?CD-ROM/DVD:???? HL-DT-ST DVD-ROM GDR860B (CD 48X Rd) (DVD 6X
??????Rd)
?CD-ROM/DVD:???? HL-DT-ST DVD-ROM GDR860B (CD 48X Rd) (DVD 6X
??????Rd)
?CD-ROM/DVD:???? HL-DT-ST DVD-ROM GDR860B (CD 48X Rd) (DVD 6X
??????Rd)
?CD-ROM/DVD:???? HL-DT-ST DVDRAM GSA-463B (CD 40X Rd, 40X Wr)
??????(DVD 5X Rd, 5X Wr)
?<Logical Storage Devices >
?.44MB 3.5" (A:??? N/A
?Applications - games - storage:233GB (5GB, 65% Free Space) (NTFS)
?Xp home (D:???? 24GB (5.6GB, 23% Free Space) (NTFS)
?CD-ROM/DVD (E:??? N/A
?Xp 64 (F:???? 24GB (5GB, 63% Free Space) (NTFS)
?Raptor games (G:?? 90GB (7GB, 8% Free Space) (NTFS)
?Ssdisk (H:???? 629MB (CDFS)
?Bf2xpack cd (I:??? 677MB (CDFS)
?Farstone (J:??? 00MB (CDFS)
?Removable Dri've (K:?? N/A
?Removable Dri've (L:?? N/A
?Removable Dri've (M:?? N/A
?Back up dri've (N:??? 298GB (3GB, 44% Free Space) (NTFS)
?Removable Dri've (O:?? N/A?EvolovE

Evolve,
I have the a8n-sli Premium which as you stated is basically the same board with a couple extra items. I have the latest beta bios ver -06. Since the early fall release the option which we will be talking about was available in the premium board which it I remember was Bios rev 9. I would download the latest bios rev.
07.04 (latest beta?or go with 06)?and flash in. Here are the steps to get the proper memory options to work and I have also included my system specs to compare.
) Hit Del to get into Bios
2) Go to the second tab on the top of the screen "Advanced"
3) Select the first option in the menu "CPU Configuration"
4) Select the first option in the "CPU Configuration" menu called "DRAM Configuration"
5) Select Manual configuration from the first Menu item.
6) The last two options in the same menu for DRAM are s/w remapping over 4G and h/w remapping over 4G. Select the "s/w remapping option over 4G" and enable it. Disable the "h/w remapping over 4G."?
7) Hit f0 and save the config.
You should now at post have 4GBws total but only 3GBs of usable memory and your X-fi should crush it in XP64 and XP32.
My Specs
A8n-sli premium (Bios -06)
amd X2 4400 (~2.5 GHZ)
4GB LL patriot memory (~228 HZ)
X-Fi Extreme Music
LSI 320-2e PCI express SCSI RAID controller (256MB buffer)
2x Seagate Cheata 5K.3?dri'ves
All water cooled
Good Luck
PapaH
By the way this is defiantly a XP64 driver problem because even with h/w remapping enabled in XP32 the card sounds fine. It only happens in XP64.

Problem with memory usage and CPU usage

Hello,
i have a problem with the memory usage and cpu usage in my project!
My application must run for more than 24 hrs. The problem is that the longer it runs the bigger is the memory and cpu usage!
It starts with ~15% CPU usage and ~70 MBytes memory usage. After ~ 24hrs the CPU usage is ~60% and the memory usage is ~170 MBytes!
After 3 days the CPU usage is almost about 70% and the memory usage is about 360 MBytes!
What can I do to reduce this huge recource usage?
Thank you!

Hi Pahe,
   I think the issue is memory usage, since CPU usage can increase due to greater memory requirements.
   Anyway, it's difficult to debug without seeing your code, can you post it (possibly for LV 7.1 compatibility)? Or just post a JPEG of the piece of code that can give problems...
   I guess you're appending data to an array instead of replace data elements, but I can't be sure...
   Have a nice day!
graziano

MSI Mainboard S-775 X48 - Problems with memory, i think

MSI Mainboard S-775 X48
INTEL Core 2 Quad Q6700 2.67GHz
MSI GeForce 9800GTX 512MB GDDR3
OCZ TECH DDR3 4GB ( OCZ TECH DDR3 PC3-12800 1600MHz Platinum XTC Dual Channel 2GB Kit(2x1024MB) 7-7-7 (OCZ3P16002GK))
THERMALTAKE 750W ToughPower
Hello.
I have bought a new computer a week ago.
First time i started the computer, two of the light diodes on the ram slot 3 and 4 was red. And have been ever since.
The bios was on default, and the computer freezez now and then, maybe every hour or something. I tried to take out the 3 and 4 memory module and set the memory volt on 1.9. And everything worked very fine.
So i tought maybe i should innstall the other two again. And now the computer is just unstable, artifacts in games, suddenly's restart's m.m.
i know its something about "spd" ,but that its way over my league.
So my questions, what is the right numbers to fill inn. ? and is it because of the memroy i have this problems?
Appriciate all the help, and sorry for bad english.
is this good enough?
Memory Frequency   534.0 MHz (1:2)
CAS#         7.0
RAS# to CAS#      6
RAS# Precharge      6
Cycle Time (tRAS)   15
Command Rate      1T
Quote
CPU-Z version 1.45
Processors Map
Number of processors   1
Number of threads   4
Processor 0
-- Core 0
-- Thread 0
-- Core 1
-- Thread 0
-- Core 2
-- Thread 0
-- Core 3
-- Thread 0
Processors Information
Processor 1 (ID = 0)
Number of cores      4 (max 4)
Number of threads   4 (max 4)
Name         Intel Core 2 Quad Q6700
Codename      Kentsfield
Specification      Intel(R) Core(TM)2 Quad CPU Q6700 @ 2.66GHz
Package         Socket 775 LGA (platform ID = 4h)
CPUID         6.F.B
Extended CPUID      6.F
Core Stepping      G0
Technology      65 nm
Core Speed      2670.2 MHz (10.0 x 267.0 MHz)
Rated Bus speed      1068.1 MHz
Stock frequency      2666 MHz
Instructions sets   MMX, SSE, SSE2, SSE3, SSSE3, EM64T
L1 Data cache      4 x 32 KBytes, 8-way set associative, 64-byte line size
L1 Instruction cache   4 x 32 KBytes, 8-way set associative, 64-byte line size
L2 cache      2 x 4096 KBytes, 16-way set associative, 64-byte line size
FID/VID Control      yes
FID range      6.0x - 10.0x
max VID         1.263 V
Features      , VT
Chipset
Northbridge      Intel X48 rev. 01
Southbridge      Intel 82801IR (ICH9R) rev. 02
Graphic Interface   PCI-Express
PCI-E Link Width   x16
PCI-E Max Link Width   x16
Memory Type      DDR3
Memory Size      4096 MBytes
Channels      Dual (Symmetric)
Memory Frequency   534.0 MHz (1:2)
CAS#         7.0
RAS# to CAS#      6
RAS# Precharge      6
Cycle Time (tRAS)   15
Command Rate      1T
Memory SPD
DIMM #1
General
Memory type      DDR3
Module format      UDIMM
Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
Size         1024 MBytes
Max bandwidth      PC3-10700F (667 MHz)
Part number      OCZ3P16001G
Manufacturing date   Week 28/Year 07
Attributes
Number of banks      8
Nominal Voltage      1.50 Volts
EPP         no
XMP         no
Timings table
Frequency (MHz)      476   571   667   762   857
CAS#         5.0   6.0   7.0   8.0   9.0
RAS# to CAS# delay   5   6   8   9   9
RAS# Precharge      5   6   8   9   9
TRAS         15   18   21   23   26
TRC         20   24   28   32   36
DIMM #2
General
Memory type      DDR3
Module format      UDIMM
Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
Size         1024 MBytes
Max bandwidth      PC3-10700F (667 MHz)
Part number      OCZ3P16001G
Manufacturing date   Week 28/Year 07
Attributes
Number of banks      8
Nominal Voltage      1.50 Volts
EPP         no
XMP         no
Timings table
Frequency (MHz)      476   571   667   762   857
CAS#         5.0   6.0   7.0   8.0   9.0
RAS# to CAS# delay   5   6   8   9   9
RAS# Precharge      5   6   8   9   9
TRAS         15   18   21   23   26
TRC         20   24   28   32   36
DIMM #3
General
Memory type      DDR3
Module format      UDIMM
Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
Size         1024 MBytes
Max bandwidth      PC3-10700F (667 MHz)
Part number      OCZ3P16001G
Manufacturing date   Week 28/Year 07
Attributes
Number of banks      8
Nominal Voltage      1.50 Volts
EPP         no
XMP         no
Timings table
Frequency (MHz)      476   571   667   762   857
CAS#         5.0   6.0   7.0   8.0   9.0
RAS# to CAS# delay   5   6   8   9   9
RAS# Precharge      5   6   8   9   9
TRAS         15   18   21   23   26
TRC         20   24   28   32   36
DIMM #4
General
Memory type      DDR3
Module format      UDIMM
Manufacturer (ID)   OCZ (7F7F7F7FB0000000)
Size         1024 MBytes
Max bandwidth      PC3-10700F (667 MHz)
Part number      OCZ3P16001G
Manufacturing date   Week 28/Year 07
Attributes
Number of banks      8
Nominal Voltage      1.50 Volts
EPP         no
XMP         no
Timings table
Frequency (MHz)      476   571   667   762   857
CAS#         5.0   6.0   7.0   8.0   9.0
RAS# to CAS# delay   5   6   8   9   9
RAS# Precharge      5   6   8   9   9
TRAS         15   18   21   23   26
TRC         20   24   28   32   36
Hardware monitor
Fintek F71882F hardware monitor
Voltage sensor 0   3.33 Volts [0xD0] (+3.3V)
Voltage sensor 1   1.23 Volts [0x9A] (CPU VCORE)
Voltage sensor 2   0.31 Volts [0x27] (VIN2)
Voltage sensor 3   0.98 Volts [0x7B] (VIN3)
Voltage sensor 4   0.97 Volts [0x79] (VIN4)
Voltage sensor 5   1.10 Volts [0x89] (VIN5)
Voltage sensor 6   1.51 Volts [0xBD] (VIN6)
Voltage sensor 7   3.33 Volts [0xD0] (VSB3V)
Voltage sensor 8   3.20 Volts [0xC8] (VBAT)
Temperature sensor 0   40°C (103°F) [0x28] (TMPIN0)
Temperature sensor 1   37°C (98°F) [0x25] (TMPIN1)
Temperature sensor 2   49°C (120°F) [0x31] (TMPIN2)
Fan sensor 0      2019 RPM [0x2E7] (FANIN0)
Hardware monitor
Intel Core 2 Quad Q6700 hardware monitor
Temperature sensor 0   44°C (111°F) [0x38] (core #0)
Temperature sensor 1   42°C (107°F) [0x3A] (core #1)
Temperature sensor 2   38°C (100°F) [0x3E] (core #2)
Temperature sensor 3   36°C (96°F) [0x40] (core #3)
Dump hardware monitor
Hardware monitor
GeForce 9800 GTX hardware monitor
Temperature sensor 0   58°C (136°F) [0x3A] (GPU Core)

I think you are going to need to go into the bios and manually set the memory voltage and the memory settings.
Try setting the memory voltage in the bios to 1.9 and then manually set the memory settings to 7-7-7-20 and see if that works. If not; then change the memory settings 8-8-8-21 and see if that helps. You might also need to up the northbridge voltage a notch or two since you are running memory in all four slots.
Psy

Msi k7n2 delta2-FSR and problems with memories(ddr 400);help me!!!

hello!!!!.
I am very frustrated because is imposible that memories work fine to 200*2.I´ve tried twinmos and now ocz premier ddr-400.When i used memtest i have a lot of errors and frozen in windows.
If i choose vdim 3.30 memtest no errors but this is a voltage very high.I don´t now what can I do.
Is a bug of this motherboard?
In other forum tell me that this motherboard don´t work good with memory to 400 but the motherboard has dual channel.
i need help.
thanks!
pos data=sorry for my english

Quote from: Stu on 26-March-06, 01:48:25
how can you have a stable OC if you have memory errors?
i don´t Know but prime no errors.
Quote from: Stu on 26-March-06, 01:48:25
forget about the OC for now, and get it working properly at stock speeds, then you can worry about getting an OC right
I have tell than 166 cpu(default values in bios),there are a lot of errors(more of one hundred and froozen in windows) in memtest.

MSI GF 6600 AGP AND problem with clocks

Hello,
I've got a big problem with saving clocks in my graphic card. Neither RivaTuner nor coolbits don't work - after rebooting computer the clocks are reseted and forced to default values.
I'm using fw 71.89 (previously 71.84).

Winter,
Run Driver Cleaner and get rid of all the old Drivers. Then install the latest nVidia ForceWare Drivers. From there try to set the clock speeds you want. (Make sure you set it to apply at startup.)
Remember that there are two speeds, one for 2D and another for 3D.
Take Care,
Richard

MOVED: MSI 785GT-E63 problems with temps and temp hardware

This topic has been moved to Off-Topic Technical.
https://forum-en.msi.com/index.php?topic=140927.0

I also use cpuid hwmonitor to check temps n volts 12 vlt rail is at 12.05 during load. The gpu load temps on the lightning nvr exceed 72c at stock and 76c with the oc. Should I get a new mobo? Compatibility issue? I was looking at a asrock 990fx extreme 3 as this would allow me to upgrade my CPU later if I choose. I am on my current main pc bc bulldozer didn't grab me. Some benches r less than the x6s, my two 6970s perform btr than a single 7970 for my needs and the only increase I would see is if I got two 7970s that's way to much coin n would be bottlenecked by my current CPU I'm sure. Any ideas? I'm at a loss

MSI GF615M-P33 problem with sb audigy se

Hi everyone
First of all in case it's useful, here's my system:
Windows xp sp2 32bit
AMD Athlon X2 240 2.8GHz Socket AM3 2MB
MSI GF615M-P33 GeForce 6150SE Socket AM3
Asus Radeon X1550 512mb (old card works fine)
Sound Blaster Audigy SE
Crucial 2GB DDR3 1333MHz/PC3-10600 Memory CL9 1.5V
0 Maxtor 80GB SATAII 7200rpm 8MB Cache
1 Maxtor 250GB SATAII 7200rpm 8MB Cache
G7 680 watt psu
So this is my third msi board and everything is fine except windows is giving me this error code: Your computer's system firmware does not include enough information to properly configure and use this device (sound blaster audigy). To use this device, contact your computer manufacturer to obtain a firmware or BIOS update. (Code 35).
I had a look at what I think is the bios version according to the boot screen A7597nms V2.0 123109 (does this look right?). Also, the advertised version of my board had a red pcb, mine is black and the version is 1.2, don't know if that's important, mentioning anyway.
Now I know the card works with the board because I did something slightly different, (just to see if it would work and save time). After building the computer I didn't reformat the hard drive from the previous mother board, just plugged it in and installed the new chipset drivers etc. Everything fine, soundcard working, except the cpu was only in single core and running very cool; less than 30 degrees c. So, decided to reformat properly, all good, cpu in multi and running around 40 degrees c, but just this problem with the sound card.
Another difference I notice is in windows control panel under Power Options I can't enable 'advanced power management' the option isn't there, so have to switch of the computer manually (which isn't a major problem). In the bios I always disable ACPI as I run a lot of audio processing software and according to some stuff I've read, can cause problems with irq's and all that technical stuff that I don't know much about.
Anyway, to the point. My question is: do I need to update the bios to 2.1 or would it be better to buy a new sound card. I've tried various bios settings and updating the drivers but makes no difference. I've even reinstalled windows with acpi enabled, again, the same error code.
Any help/questions much appreciated. Hope I've explained this well enough.

Quote
So this is my third msi board and everything is fine except windows is giving me this error code: Your computer's system firmware does not include enough information to properly configure and use this device (sound blaster audigy). To use this device, contact your computer manufacturer to obtain a firmware or BIOS update. (Code 35)
Quote
In the bios I always disable ACPI as I run a lot of audio processing software and according to some stuff I've read, can cause problems with irq's and all that technical stuff that I don't know much about.
What HAL is installed? Look in device manager under "Computer"

K7T266 PRO2-RU and Problem with a FEW DISPLAY ADAPTERS ...

Hello ,
I was using my mainboard with 32 MB Creative Riva TNT2 Ultra until creative's fan was damaged . I tried 16 Creative TNT2 m64 display adapter of a friend of me , but it didn't work with K7T266 PRO2-RU. Many sounds are coming from mainboard while D-LED shows Testing RTC (or boot attemp, I'm not sure about that) (Same symptoms with "no graphic adapter" - I tried again after unplugged the display adapter - )
At the beginning I was thinking that the 16 MB creative graph adap. was broken . So , today I bought a new graphic adapter 128 MB of Creative 3d Blaster5 Radeon 9200SE . When I plugged it into mainboard , I saw the same problems with 16 MB Creative TNT2 m64 . After that , I found another 32 MB Creative TNT2 Ultra from my friend and it worked with my mainboard FINE .
- I tried all of the old bioses of MSI K7T266 PRO2-RU
- I tried to start the computer with no any other devices (such as HDD , sound card , tv card etc. ) . Only display adapter was plugged in the mainboard , but it didn't work . System hanged up everytime I tried .
- I made some bios adjustments which are suggested at this forum ....
But none of these worked .... ?(
What is the problem ? Why only 32 MB creative TNT2 Ultra is working with my mainboard , but 16 MB Creative TNT2 M64 and 128 MB Creative 3DBlaster5 Radeon 9200SE are not while all of them are working FINE with an old PII mainboard . (tvout+DVI) I'm looking forward to hear from you . , Help me please .
Ps : Can new beta bios solve that problem ?
XP pro
2100+ 0.18m XP CPU with coolermaster CP5
40 GB Seagate Barracuda IV
300 watt Codegen Power Supply
2*256 MB Kingston DDR 2100 Memory
( No floppy , no souncard , no tv card etc , no any other devices like cdrom , dvdrom , cdrw etc.)

That's it!
I provided a few PSU's from my friends and tried 420 watt thermaltake and 520 watt VANTEC Stealth 520A PSU ...
Same situation happened and 128 MB Creative ATI Radeon video card didn't work ...
The problem can not be about PSU ...
I tried two different brand of fx 5200 (128 MB ) video card on my system (with 300 watt codegen PSU) . Everything is ok .
And I also tried the RADEON card on my friend's computer which is running with 230 watt Elan Vital PSU . It worked perfectly ...
So what can I think about that situation?
The Answer is : There is something about MSI mainboard ... When I wanted to contact with support center via e-mail , I got an automated e-mail answer which is not completely able to solve any of my problems.
Besides , I saw the problems between brand new Nforce mainboard of MSI and ATI video cards ...
SO , if we get all of these informations together , we can say "THERE IS SOMETHING ABOUT MSI" ...
The solution is not buying expensive PSUs...
That's really bullshit , I can buy a brand new mainboard instead of an expensive PSU.
Finally , I bought an Asus mainboard , everthing is going ok now!
I'll not buy products of MSI anymore because they didn't do anything to solve my problem . Goodbye MSIIIIII ....................................... ........

MSI P45-C51 (Problems With 4GB DDR3 1333)

Hello,
I have a problem with my motherboard P45-C51.
According to test reports, this motherboard supports 4GB DDR3 modules (1333).
msi.com/file/test_report/TR10_1836.pdf
Data specifically are:
Model: Kingston KVR1333D3N9/4G
Size: 4GB
2 DIMMs: V
4 DIMMs: V
R.S.T: OK
In the absence of stock the store, I bought a similar one:
Fury HiperX DDR 3 1333 (HX313C9F/4)
however, the motherboard does not recognize the memory (when I turn on the computer, 3 beeps sound and restarts, return to ring 3 times and then restarts and so on)
With 2 GB DDR3 1333 DIMM working properly.
I have last Bios v5.7
I found an online store the specified memory for my motherboard (Kingston KVR1333D3N9/4G) but want to be 100% sure it worked properly before buying.
Thnks.

hi,
With Fury HiperX DDR 3 1333 (HX313C9F / 4) i deleted the CMOS but I did not recognize. After much searching, I concluded that the problem could come from the distribution of the chips.
The Kingston (Fury HiperX DDR3 - 1333 - HX313C9F/4) memory have 512Mbx8 Chips (single-sided)
The G.Skill Ripjaws (F3-10666CL7D-8GBRH) memory have 256Mbx16 Chips (in two sided)
With G.Skill The mbo detect the memory and boot normally. No necesary delete CMOS.
The only problem is latency, latency detects and configures it is nine. However, changing the latency in the BIOS manually to seven working properly.
Thnks.

P35Neo2 FIR and problem with booting

So I have problem with booting my compie. Compie try to boot to the part of start windows, after that in case of switch into graphicis mobo going down and restarting (WinXP SP3). I think, that problem is not in PSU, cos i have 800W XILENCE (+3,3V 28A, +5V 32A, 4x+12V 20A, -12V 0,5A, 5VSB 3A), Board P35 Neo2 FIR, E7200 proc, bios 1.9 (updated). I have 5 disk and use raid function in bios. Graphic Radeon HD3650, Memory Zeppelin 4x1GB KIT 800Mhz.
I start with change of PSU from 550W to 800W but it didnt work, previus PSU had (+3,3V 30A, +5V 32A, 2x+12V 18A, -12V 0,8A, 5VSB 3A),
i try change memory, but no efect.
After update bios there was standard warning about bad cheksum, after resave Bios settings it was gone, and compie boot after that.
Any idea?
Thanks

So my problem is solved...but my feeling of this is not good...
I updated BIOS from 1.9 to 1.10, reset Bios settings, after restart i pressed F2 for load standart settings and i changed in Bios only that i am using RAID and disable disket and it works...i boot my compie into windows without any problem...
So i try change another things in Bios and my compie hangs in continous resets without booting into windows...no BSOD only restart and restart...
After reseting Bios settings and again Load to Default it works...and run windows...
There was only one new thing ... screen flick for the second with new screen about checking NVRAM ....this screen was not visible before (and maybe this is the problem), cos if i change something in BIOS about clocking and power management and other ones, this screen is by booting missing...and compie not run in Windows...
Next thing what i see, that in CPU multiplication dont work multiplication 9,5 and proc used frequency 2400 (9x) (it is E7200 on 2533)
i hope that this bios 1.10 fixed my problems...and my opinion is that P35 Neo 2 FIR is not ideal board for E7200 proc...so i m looking for another proc...and maybe another board...

New C6-01 user/phone and problem with backup/resto...

Hello everyone.
I recently purchased a new C6-01 (and first-time Nokia owner) and having trouble with getting maps restored onto a new 32GB uSDHC card and need some help.
It is my understanding that I can backup and restore all my phone contents and settings to a new memory card using Nokia Suite. So what I did is performed a complete backup using Nokia Suite, ejected the old uSD card (that came with the phone), put in the new uSD card that I had purchased and format it, then performed a complete restore to the phone and the new memory card.
During the restore, I saw errors on the phone display that said something like disk write error and gave me the option of stop or retry. I hit the retry a few times and still getting the error. Thinking it may be a bad uSD card, I returned/exchanged for another identical one. With the 2nd new card, I still get the same error message so I rebooted the phone and ran restore again but this time instead of restore everything all at once, I selected a few items at a time and eventually got everything restored, at least without errors this time.
When I ran maps after the restore, it told me that I needed to download the maps, and when I tried to download it thru a WiFi connection (at my house), I keep getting Disk error - cannot complete write. Retry or data will be lost. At this point if I run Files, it will show drive E but not any free space number (and selecting it will show free space not available). A reboot will bring back drive E and show 29.4GB free. So I am completely stumped at this point and believe that for whatever the reason I can not get maps loaded onto a non-Nokia-provided memory card.
I am running Nokia Suite 3.5.34 on WIndows XP w/SP3. The new 32GB uSDHC card is a class 4 card made by Sandisk. The phone is running the Belle Refresh v111.040.1511 dated 7/28/2012. Map version: v3.09 12wk20 b01-MW OpenGL MN-Map version 0.2.46.103
Sorry for the large amount of information posted here, but I wanted to provide enough details for you to look at. Please feel free to ask for more information and thank you in advance for your help.
Bill

yes I reformatted the card, and after it was finished, I ran Maps. When it told me I need to download the maps (and gave me 3 options), I exited and connected the phone to my computer, browsed and deleted the cities folder and the qf file. Waited a little bit and reran Maps. This time I used the WiFi connection from the phone to download.
I gave me an error when I tried to download the entire USA maps, so I selected Texas and Pennsylvania state maps. Those downloaded ok. Next when I tried to download New Jersey, it started a little bit and the disk error message came up again so I hit stop. Ran Files and saw the memory card is grayed-out (did not indicate and free space), I know the same problem is happening again.

MSI 645Ultra and problem with memory.

Similar Messages

Maybe you are looking for