MSI 651M Combo-L Video Int problems

I have install at MSI 651M Combo-L Windows XP prof+SP1 (Windows 2000 prof+SP3/SP4). After install Video drivers for intergration video, my system is abend with error 0x7F. With using Windows 98 - video is installation and work - good. My BIOS - 1.3, Video Drivers - Driver version: Win2K/XP: 6.14.10.2170.
Please help.

a marginal psu may be?
http://www.memtest86.com on ram

Similar Messages

MSI 651M Combo-L

Just installed an MSI 651M-L motherboard with a 2.0 Ghz Celeron processor. (All new)
Turn on for initial boot and nothing. CPU fan comes on, power supply fan on, Power switch and HD LED on, but no CMOS boot. CD ROM and CD ReWriter trays will not open although lights are on. If I disconnect them from the IDE cables, trays open and close.
Tried different RAM, different video card, different monitor, nothing works.
There is not a beep, nothing. Is this just a bad board?

What is the D-bracket status ?

MSI K7N2G-ILSR onboard video initialization problems

Hi, today I replaced my wife's trusty Abit KT7 motherboard with a MSI K7N2G-ILSR. I used the onboard video since she doesn't play games. Everything seemed to be working fine until I went to boot it up. The computer started up as usual, but the monitor did not intialize like it should. The message on the monitor said that " the monitor was working correctly and to check the cord or the computer." I rechecked all of the connections and everything seemed to be installed correctly. I thought that maybe there was something wrong with the onboard video, so I decided to install the Radeon 9000 that was in the old system. To my suprise I received the same message when I started the computer up the second time. I have built several systems and have never encountered a problem like this before. I read the thread about problems with the Radeon cards, but no one mentions anything about problems with the onboard video. I am using a Duron 750, Antec 330 watt PSU and 512 megs of Kingston Value Ram. I know that several posters have recommended that nforce 2 users need a more pwerful PSU and better ram, but I have a hard time beleiving that those things would cause the video not to intilaize. I would appreciate any feedback and/or suggestions because I need to make a desision about hwat to do with this board. Thx.

Well I appreciate the replys. I formated the harddrive before I installed the motherboard because I was worried that the via drivers would cause problems when I booted it up and installed Win XP. Bonz, you are right, I am just guessing that everything is OK since I can hear the system start up, but I can't see anything since the video never intializes. I rechecked all of the connections and even took the motherboard out and reinstalled the cpu, memory and motherboard and the same thing happened. I started thinking something was wrong with the monitor so I unplugged the monitor from my system, which I know works, and it did the same thing. I just wish I could get the video to intialize so I could see to get into the bios to look around. I will check the jumpers on the board and continue to mess around with it. I would appreciate any feedback I can get. Thx again.

Msi 915G combo-fr memory readout problem

well i bought this ram which is capable of running at 533 mhz at 3224 timing or 700 mhz at 43312 timing so i buy it right and i buy this board so ever thing boots up but it reads it as 400 so i go in bios and put it to 533 but it still says 400 when boot. i think there needs to be a bios update and also when i raid fsb frequency is raises the fsb above 533 but it doesnt give me that fsb eather it over clocks from 400 so if i have 250 fsb it will make it 500 witch is under the miniumum setting for my ram so what could be done to fix this i think is bios programmer guys at msi provide bios update with a forcable memory fsb option that raises or lowers by typing in or raising 1 mhz at a time link to memory http://www.techniz.co.uk/modules.php?name=Reviews&rop=showcontent&id=186
some people with problems i have also links
http://www.ocforums.com/showthread.php?t=363573
https://forum-en.msi.com/index.php?topic=69004.0
thank you very much

Please read the Forum Rules. You are asking to speak with someone from MSI and there aren't any that visit here.
You are asking for a memory clock that is totally independent from the cpu clock. That will not work; they have to run at a fixed ratio. No bios change can possible "fix" the physically impossible.
Your best memory performance is when the two clocks run syncrhonously, which for your cpu is 400. The ram you have purchased would be suitable for a 1066 FSB cpu and board without overclocking, or it is great stuff for overclocking.
Quote
been 2 days now?
For rapid personal response, the cheque you mailed us must first clear the bank.

MSI KT2 Combo-L Memory Timing Problem

Currently I have two sticks of Kingston 256MB PC3200 CAS3-3-3-8 ram on this motherboard. (Worked in Dual Channel in my P4P800 at 2.5-2-3-5@PC3200)
Running AMD XP2000+, 266FSB
They're rated to perform fine with 2-2-2-6 timing in PC2100 mode...(checked both datasheets and utilities)
I have already set all these in the BIOS with Command Rate = 1T, FastCommand = Ultra, Bank-Interleave = 4 way
Funny thing is, in CPU-Z or other utilities. I'm getting 2-3-3-6...or RAS to CAS delay = 3, RAS Precharge = 3 instead of both being 2.
Is there any way to fix this problem as I want to set the timing as low as possible...
Thanks.

Quote from: me_AMD on 29-January-06, 19:37:06
...CPU-Z is probably reading SPD rather than your BIOS setting...
SPD has 2-2-2-6 at 266MHz...
So i doubt it's just CPU-Z. Even Everest and Sandra report the same thing.
The funny thing is that it wouldn't lower it anymore even tho I chose all the lowest values...On my other AMD machine, I could lower it all to 2-2-2-6. This is the reason I'm asking.

MSI 915P Combo FR problems

Hello people! I have problems with my mobo , my mobo is :
"Motherboard ID   63-0100-000001-00101111-022306-GrantsD$0AAAA000_915P/G COMBO A7058IMS V1.9 02/23/06" ( everest copy/paste) . Now i have updated my bios to the 1.9 version, the latest available, before that, the mobo would not accept double sided DDR1, and after the update the problem persists, and i think one of the ram slots is not working properly , beacause it won't accept DDR1 single or double sided.
Does the latest bios-update contain previous versions?
Please help me , i want to upgrade my RAM and i can't find single sided memorys anywhere . Thank you in advance.
My configuration is:
CPU Type   Intel Pentium 4 531, 3000 MHz
Motherboard Name   MSI 915P Combo-FR (MS-7058)
Module Name   Corsair VS512MB400C3 ( single sided )
Video Adapter   NVIDIA GeForce 6600
Audio Adapter   C-Media CMI9880 @ Intel 82801FB ICH6 - High Definition Audio Controller [B-1]
Disk Drive   HDS722525VLAT80 ATA Device (7200 RPM, Ultra-ATA/100)
Optical Drive   HL-DT-ST DVDRAM GSA-4165B ATA Device
Network Adapter   Realtek RTL8139/810x Family Fast Ethernet NIC

What's the exact problem ?
you have one stick of ram and the system fails to boot with it ?
or you added ram and the system fails to boot ? or does not detect the extra ram ? ...

MSI K7N2 Delta-ILSR, Mouse problem & Video off problem solved!!!

I find the following information that I collected very interesting at the very least...
Here goes...
The video off problem that I was having was directly linked to the mouse. Here, let me explain the video off problem. In the BIOS Have the Standby mode set to S3. The problem occurred when I started windows, then went into standby, then started back up, then restarted the computer, the monitor would act as if it were in sleep mode, or rather there was no signal being sent to the monitor. Well the odd way I fixed that is by plugging in a standard 2 button PS/2 mouse. Also this fixed the issue with the mouse sometimes not working in windows.
Here is how I tested.
Logitech MX700 Cordless Optical Mouse, PS/2 & USB= failed.
Logitech iFeel Optical Mouse, USB= failed.
Microsoft Cordless Ball Mouse, PS/2= failed.
Standard Artec (Cheapy brand) Ball Mouse (With no wheel), PS/2= All issues fixed, and passed.
When I said failed I do not mean they didn't work, I mean they sometimes didn't work and also caused the Video off problem after restarting the computer.
Obviously it isn't the ports (PS/2 or USB) that are the problem, it is more like the mouse itself, and the amount of buttons in particular. As you can see above the only mouse that works correctly is the one that only has 2 buttons, the rest has 3 or more buttons along with a Wheel. The MX700 has 8 buttons + wheel, WOW!
Anyways I figure out it was the mouse, and not the memory.
Obviously MSI needs to make a patch for this mouse problem.
I'm still having a hard time believing that the mouse caused the video not to work, but it is true! I spend well over 5 hours testing this crap. Every time with the mice with more then 3 buttons it messed up, and every time with the 2 button old fashion mouse it worked flawlessly!
MSI, get to work on a new BIOS to fix this mess!!! :]
BioHaz

Quote
Originally posted by Raven_
hi
its possible to use an ps/2 mouse AND a usb mouse at the same time.
i used the ps/2 mouse in windows and the usb mouse when playing games.
you can get some trouble if you do it the way i did it.
i was in windows surfing and the pointer just jumped all over the screen.
when i looked on the other side under a table a friends little kid played with the usn mouse. )
bye
LOL, that isn't what I'm talking about.
There seems to be a problem with my motherboard accepting mice with more then 2 buttons. It works the first time, but if you restart the computer, the video goes off. If you have both installed, it still messed up.
BioHaz

MSI X52P Combo Drive Problem...

Hello all
I recently purchased the MSI X52P Combo CD-RW / DVD-ROM drive to replace my old CD-ROM drive. Installation went well, XP Pro booted up, installed it's own ATAPI COMBO52XMAX driver and the drive appears as DVD/CD-RW Drive in my drive listing as expected. The only problem is, it will not read any disc in a normal XP Pro boot.
After investigating, the drive reads discs perfectly using my old Win98 boot disk which uses a different ATAPI driver (the drive flew through a dir *.* /s on the bundled 600MB odd Nero CD in seconds) and also works perfectly in Safe Mode.
As it worked perfectly in Safe Mode I took that opportunity to install Nero. I then rebooted and discovered that I can use the drive to burn a CD with Nero in normal mode (which reads perfectly in another drive) but again in normal mode won't read any discs including the one I burnt. I'm just trying to remember what the differences between Normal and Safe Mode are. They both use the same driver but doesn't SM use Real Mode Drivers?
Anyway, so far I've tried...
Every combination of IDE channel / master slave setup possible.
Updating the firmware, it's now the 1.40 version.
Checking this forum, seems other people have had similar problems.
A bucket load of things that perhaps only mad people would try.
For the record, there are no device conflicts and AMIBIOS reports it as VER 1.40 ATAPI COMBO52XMAX on boot up. Note, I have been building / tinkering / playing with PC's practically all my life but this is really the first time that I have been stumped with a hardware problem.
Any help / suggestions / ideas would be greatly appreciated. I know the drive works perfectly, just not in normal mode

AHA!
Getting somewhere.
Device Manager - IDE ATA/ATAPI - Secondary IDE Channel - Properties - Advanced Settings
Changing Transfer Mode from 'DMA If Available' to 'PIO Only' caused the drive to immediately spring into action and read discs of all types. However, I'm not happy with that so will fiddle further. PIO mode is processor intensive whereas DMA mode uses the disk controller to transfer data to memory without lugging the proc.
So without looking I am guessing that the difference between Safe Mode and Normal Mode is that Normal Mode tries to use DMA first whereas Safe Mode just uses PIO to be safe. My hard drives are happy chugging along in DMA mode so I'm sure the X52P should too.
Hope this information is useful to anyone else having difficulty reading discs.

MSI 651 Combo / MS6769 Problem with Temperature

Hi. I´m having some troubles with my mb, since 2 weeks ago. Suddenly, it starts to appear that cpu temperature go 70 º C (158 º F), and i hadn´t do anything. I changed the cooler, and put some new grease, and nothing happen. Then i searched in this forum, and i found a message simmilar, that said something about upgrade bios, and thas what i recently do (WS6769 v1.0 originally, then V1.3, then V1.2). But nothing...
What should i do? buy another mb? I don´t want to.
Thanks.
Claudio

Well, i´m pretty sure that it is the mother board, because, i already changed all what´s possible to change: processor, RAM, hd, power supply, processor.
Din: I don´t know what´s "corecenter". I already upgraded BIOS (to v1.2 that supuestly fix my problem), and put thermal paste (grease? in spanish "pasta disipadora") between CPU cooler and CPU. And i do change the processor (i put a p4 1,8GHz), with other FAN processor (CPU cooler), and the same temperature.
Danny:Those details you ask me:
In a label on the power supply (lVoltage MAXAmpere): +5V 30A, +3.3V 20A, +12V 15A, -12V 0.8A, -5V 0.5A, +5Vsb 2.5A.
It is a Maxpower 300 Watts ATX, model PX300.
On BIOS PC Health: Sys Temp: 18ºC/66ºF, CPU Temp 66ºC/150ºF (up to 70ºC), CPU Fan speed 2909 RPM, Vcore 1.68V, 3.3V 3.26V, +5V 5.10V, +12V 12.03V, -12V -12.19V, VBAT(V) 3.26V, 5Vsb(V) 5.14V.
I have a Celeron 1,8 GHz, socket 478, a MSI 651 Combo MS6769 Motheboard, with nothing else. Hd Maxtor 30Gb, Rewriter MSI 52x24x52.
The problem: From one day to another, it wasn´t load XP. It resets itself after a few seconds (about 5 secs). On the BIOS PC Health section, i actived the CPU Temperature beep on "too much degrees" (i don´t remember the exact name, but that´s the idea). And that´s how i realize that the temperature is the problem. I think it is how the motherboard inform the temperature, and it is a nominal temperature, not real. If it´s real, i already had a burnt processor.
Anything else that can help to find a solution for me?
Very thanks.
Claudio

MSI VOX Audio / Video Sinc problem

Hi All.
Last week i bought a VOX TV Tuner. Nice device works well except for what i want it for.
When I try to cpature at Full PAL DVD resolution I get audio / video sinc problems. The audio is usually ahead of the video. Half PAL DVD or below it's fine.
I suspect it is the basic design of the box that is the trouble. Having the audio feed to the sound card rather than than in the USB2 feed has been a no no ever since the problem was discovered back in the USB 1 days. USB2 is capable of 400Megbits..
However I contacted another user who has no problems and says there is a patch for Direct x PAL video capture. Does any one know of this patch or has any one had the same problem as I have??
This device seems so new that there is no info on the net about it..
TIA.
System : P4. 2.4 Gig, 512 Meg ram, fast HDs, Direct X 9.0 (have not installed 9.0b yet) Asus Mobo P4Pe. Matrox Mystique video card. Win 2K SP4

Quote
However I contacted another user who has no problems and says there is a patch for Direct x PAL video capture
I would chase that up as it sounds promising.

[VIA] MSI KM2M COMBO(MS-6738 VIA 8375 and G-force 6600 or 6600GT..Help

Hi and thanks I would like to buy a videocard like these two MSI GEFORCE 6600 GT 128MB TV-OUT DVI VID-IN AGP or
MSI GEFORCE 6600 256MB TV-OUT DVI VIDEO-IN AGP.what u think guys and i have this system..
Mothebord....MSI KM2M Combo (MS-6738) 3 PCI, 1 AGP, 2 SDR DIMM, 2 DDR DIMM, Audio, Video
chipset   ..VIA VT8375 ProSavageDDR KM266
CPU    AMD Athlon XP, 1800 MHz (13.5 x 133) 2200+
VideoCard   NVIDIA GeForce FX 5200 (128 MB)
Microsoft Windows XP Professional
1024GB DDRRAM PC2100 266MHz
Thankz

sorry for that memory is like you said 266MHz and not 233, and the price of the two cards isn't that much different..i can buys either one ...what i want to know is if my motherbord can take such cards and not to have any problems in future,i don't want to buy any of these videocard who doesn't fit this mothercard
thanks again

"915P Combo and PCI-Express problem"

Hello friends, I have a pc with the following configuration: mobo 915P Combo with a processor pentium 4 530 3.0 ghz, memory kingston 1GB Kit DDR 400 dual channel, psu 500w ATX with connector 20-pin, video card XFX Geforce 6600 256 MB PCI-EXPRESS, sound card audigy 2 zs, hard disk 120 GB seagate 7200 rpm SATA. And I have a problem with the port PCI-Express and my video card, if I install the video card the computer it doesn't start up well, that is to say, it start up and to the 3 seg this shut down automatically and 5 seg later this tries to start up but without success , after several intents this can start up perfect and everything works well . And if I don't install the video card pci-express and I intall my old video card port pci 16 mb Banshee the pc starts up perfect and doesn't have problems. what is the real problem? 1) the video card pci-express, 2) the port pci-express of the mobo, 3)that I have a psu with connector 20-pin? Thanks

dear moderator,
i got same problem as Calvido. My system specification MSI 915G Combo with the lastest bios v1.8 with a processor pentium 4 530 3.0 ghz, memory kingston 1GB DDR 533 dual channel, psu 350w True power, video card Leadtek Geforce 6600 256 MB PCI-EXPRESS, hard disk 120 GB maxtor 7200 rpm SATA. And I have a problem with the PCI-Express, if i use the intergrated graphic intel 900 it dun give me any problem n i used for more than 6mth.
It happen when i try to upgrade my intergrated graphic card to PCI-E. 1st i try with the Inno3D geforce 6600 256mb PCI-E n when my com start until windows it become blank screen for awhile the screen appear again for no more than 1 min became blank again. 2nd try i use Leadtek Geforce 6600 256MB PCI-E it seem alright but when i click on icon it start to delay ...until hang. 1st i thought my OS problem so i format my system, but problem still the same so i repeat format until 7 or 8 times. Problem not solve.
I try to send email to MSI but no reply
Pls help me to solve the problem
best regard

MSI 915G combo no sound or internet

Hi
Motherboard: MSI 915G Combo
For one day ago I decided to format my hard drive.
I installed Windows Xp professional and all drivers.
But when the computer had started up so didnt the sound or the internet work, I've tried to reinstall the drivers to my motherboard, but it didnt work. So are there a problem with my motherboard, or something else?

Have you installed the cmedia audio drivers properly? Get the latest ones from http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=604&kind=1

MSI R48R4870-T2D1G-OC video card and the MSI K9A2 Platinum

I recently bought the new video card for my system the R4870-T2D1G-OC.
MSI stated that the power cord for the video is not a required, and the MSI board has its own connection for power to the video.
When I tried installing the new card all I get is a series of beeps, as if there is not video card installed. BEfore I send it back and replace it with another I would like to verify that it does not require the power connector and that perhaps I need to do something special before I repalce the card.
I have always used the MSI mainboards and never had a problem till now.
Daniel

Quote
The system boots and I see the dos screen, then it goes black
You mean you see the BIOS logo / POST screen, and then nothing? So the card is working then, no beeps?
Quote
I have replaced the power supply and loaded the drivers supplied by MSI. Now I have no video.
Can you elaborate, as I don't know how you can install drivers if you're not getting any display? ???
Quote
What can be done to get the APPROPRIATE drivers for windos Vista, or do I need to install the 3rd party software to get the ATI cards to work.
Download the Full Catalyst Suite for your appropiate OS version from here:
http://game.amd.com/us-en/drivers_catalyst.aspx

MSI 651M-V SiS 651 having trouble finding audio drivers sis 7012

Hey there folks....
I recently aquired a 2nd hand computer, which came wiped clean with no disks for drivers, no info etc...
I've been having a hell of a time tracking all the drivers down, and I am currently trying to track down the multimedia audio device drivers... With no success.
When I use MSI live update it has no options for audio device drivers, I've tried downloading SIS 7012 audio device drivers and I get an error... I'm assuming this is because the drivers are for a card, not onboard...
Any help here would be GREATLY appreciated... I've managed to find drivers for everything I've tried so far... but this one has totally stumped me and i am getting real frustrated!!!!!
System specs according to Everest.... (if theres anything else needed let me know this is just the summary)
Computer:
Operating System Microsoft Windows XP Home Edition
OS Service Pack Service Pack 2
DirectX 4.09.00.0904 (DirectX 9.0c)
Computer Name HOME-PC2
Motherboard:
CPU Type Intel Celeron D 320, 2400 MHz (18 x 133)
Motherboard Name MSI 651M-V (MS-7005 v2.0) (3 PCI, 1 AGP, 2 DIMM, Audio, Video, LAN)
Motherboard Chipset SiS 651
System Memory 512 MB (PC2700 DDR SDRAM)
BIOS Type Award (10/06/04)
Communication Port Communications Port (COM1)
Communication Port ECP Printer Port (LPT1)
Display:
Video Adapter NVIDIA GeForce FX 5200 (256 MB)
3D Accelerator nVIDIA GeForce FX 5200
Monitor IBM 6546 G52 & G54 [15" CRT] (66-C0852)
Multimedia:
Audio Adapter SiS 7012 Audio Device
Storage:
IDE Controller SiS PCI IDE Controller
Floppy Drive Floppy disk drive
Disk Drive WDC WD400BB-75FJA1 (37 GB, IDE)
Optical Drive HL-DT-ST CD-ROM GCR-8523B (52x CD-ROM)
SMART Hard Disks Status OK
Partitions:
C: (NTFS) 38138 MB (30282 MB free)
Input:
Keyboard Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
Mouse Microsoft USB IntelliMouse Explorer
Network:
Network Adapter SiS 900-Based PCI Fast Ethernet Adapter (192.168.0.169)

you can find all drivers which you need for your board here:
http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=576

MSI 651M Combo-L Video Int problems

Similar Messages

Maybe you are looking for