MSI-6967 power transmission level

Why I can't change the power transmission level on my computer.

Dear starfoxACEFOX,
Thank you for reporting this issue.
Here is the latest Beta BIOS for your review.
The latest Control Center v1.0.173 from our website:
http://www.msi.com/index.php?func=downloaddetail&type=utility&maincat_no=1&prod_no=2025

Similar Messages

  • Can setting power output level at 65mw cause a one year old router to fail?

    Recently my router WRT54GS v2.1 that is only one year old but has been in 24/7 service failed and the technician that worked on it said the failure was probably due to the power output level being set at 65mw and other firmware settings ( particulars available ) that had been used but were working fine to provide wireless service. The output was fed to a Smart Amp 500mw power amplifier with Automatic Gain Control then through 30 feet of 400 cable to an Omni-directional 14 dbi antenna. Coincidentally the power amp seemed to fail at the same time. The maximum input to the Smart Amp which has AGC is 23dBm (200mw) max. Is it possible that the firmware configuration and the 65mw setting were responsible for the failure of either or both devices?

    If the ABS and Router/Modem are both giving IP Addresses out, (that's what tells everything on the Network where to send/get stuff to/from), then everything gets confused... a bit like trying to get US Mail delivered when your street has 2 names, and your abode has the same address as other houses on the block!
    You just want the ABS to pass on the IP addies that the Router hands out, and not try to do it itself.
    If your base station is connected to a router or other network device that is using NAT to share a single Internet connection with multiple computers on your network, and you are using DHCP to provide private IP addresses, you need to turn off NAT and DHCP on the AirPort base station.
    Most networks need only one device using NAT and DHCP to provide IP addresses.
    To turn off NAT and DHCP:
    Open AirPort Admin Utility, select your base station, and click Configure.
    Click Network and deselect the "Distribute IP addresses" checkbox.
    If your base station supports Power over Ethernet (PoE), by default the "Distribute IP addresses" checkbox is not selected, and the base station is not using NAT or DHCP.
    With NAT and DHCP turned off, the base station acts as a simple bridge between the wired and wireless computers on the network.

  • Power transmission project

    Hi Gurus.
    I am shifting to power grid transmission project.I need face client interview.So
    Could you please give the idea of Power transmission project's business scenario?
    Please tell me the areas i need to prepare?
    Bcoz as per my idea they maintain like pipeline material?
    I need overview of power projects business flow.
    So kinldy provide this.

    Hi,
    You have to look into different Bussiness processes.
    1. Normal purchaing cycle
    2. imported purchasing cycle.
    3. Vendor Evaluation
    4. Refurblishment Process
    5. Split valuation
    6. And stock transfers
    Thanks & Regards,
    Kiran

  • MSI 6967 or PC2PC license problems!!

    I have 2 MSI 6967, also known as PC2PC.  The drivers on CD are erratic, but I previously managed to get it to work fine with a upgrade to a newer 1.3.x driver.  Now with 1.4.x the damn thing is asking for a license key on install (I was unable to retain the compressed driver file that worked, regrettably).  
    So I went to the slightly rubbish web form to get these, and I entered the correct BD address for each of my devices (I know this to be true, as I when I try to re-register these the web service gives a 'rogue registration' response, so it must store the registered BD's), and obtained a 32-digit key for each.
    When it asks for one of these keys on install, I give it, and it seems ok.  That is, until it has finished, whereupon the bluetooth system tray icon remains red (inactive, or problem), and only the option to 'Start using Bluetooth' is given on right-click.  Naturally I tried this, but it says:
    "Your bluetooth software license does not include use with this Bluetooth device. [6]"
    When I click OK, it then tries to get me to point it to a new, valid license file.  The only one I can see is in the unpacked files that came with the driver download.
    I entered the BD correctly on registration, and it must have been valid as I got a 'valid' response i.e. the web form authorised it as an MSI bluetooth device with that address (presumably the whole purpose of the form, apart from spamming you to high heaven).  I can't do anything else now as it won't let me re-register these BD's anyway.  I can't find the mysterious older driver that worked now, as you can only download the latest (i.e. ) one.  I can't even verify the BD's now, as it doesn't give me the option to go to configuration of the device (although surely they are fixed identifiers anyway, like MAC addresses?).
    Come on MSI, this is POOR service!!  I own these devices, I paid for them, you let me use them for a while and now you have told me to shove it...  If there is no way around this insanely crap rigmarole, please make a driver history available.
    I recently ordered a new-build pc, and I specifically avoided MSI motherboards and other components because of this specific problem I am having with my 'legacy' MSI bluetooth omponents.
    Can someone please let me know how I can get my stuff working again?

    hi
    i bought the adapter today and it was shipped with the old 1.3.1 drivers that didnt work on my w2k pc *EDIT*(bttray say no device, but w2k devicemanager say device is ok and drivers are running)*/EDIT*. so i tried to get the update and ran into the same stupid problems (wrong license file message) :(. the only positive think is that by reading in this forum i find out that:
    1. im not alone with my problems.
    2. if msi was thinking when the talk about 'link to the future', that i have to read lots of rather old postings, that only states that msi didnt care about the problems, or simply can't fix them. and the only solution ist to go to the darkest corners of the internet to get a crack for something that i already payed for.  i think its better for me to stay in the past and never again buy parts from msi, not for me nor for any of my customers (i'm nearly 15 year's in the pc/network troubleshooting bussines).
    3. tomorrow i have to go back to the schop where i bought this useless pice of hardware and give it back. then i wait that the acer adapters are available again. (i use already one on my notebook and was fully satisfied with it, and had mostly no problems at all, at least not such stupid ones).
    greetz nb

  • [Request] UEFI GOP VBIOS for MSI R7750 Power Edition

    Hello, I need a GOP/UEFI Vbios for MSI R7750 Power Edition.
    S/N: 602-V271-08SC1208010276
    ROM: goo.gl/tphw4h
    (Temporarily I have no permission to post a http link, so I had to give a shorten one.)
    Regards!

    here it is
    for flashing: http://www.techpowerup.com/downloads/2306/atiflash-4-17/
    flash syntax from pure DOS, after booting from bootable USB key:
    atiflash -p -f -noaper 0 xxx.rom [ENTER]
    where "xxx.rom" will be your vbios file which you want to update

  • MSI 6967 bluetooth headset problem

    I have recently bought a MSI 6967 as it supports the headset profile. MSI was installed with the 1.4.2.10 drivers. When i tried pairing my Jabra bt200 headset i was able to record normally on sound recorder however, i wan't able to use MSN yahoo etc... as the microphone would not pick up any sound.
    Is there anybody out there that would be kind enough to help me sort out this problem. I have winxp sp1
    thanks

    bumpin

  • Upgrading From Dual Core to Quad Core on an MSI 7246 Power Up Edition

    Good day folks.
    I'm upgrading a dual core Pentium Extreme Edition 955 (3.46 GHz) to a quad core Intel QX6800 Extreme Edition (2.93 GHz) which my MSI-7246 Power Up Edition is supposed to support.
    I'm running Windows XP with all the latest patches installed.
    Are there any special procedures I need to follow to accomplish this without a hitch? I.E., I certainly do no want to have to reinstall the OS.
    I've read a couple of posts which talk about deleting the processor entries which are now correctly listed in Device Manager.
    Thanks in advance for any help.

    Quote from: Henry on 14-November-08, 13:32:48
    I forgot to add, clear CMOS wouldn't hurt before you start it up after the CPU change.
    OK. Will do. Sounds like good advice.
    Appreciate the tip.
    EDIT: As a follow-up the upgrade went smoothly except for loading the drivers for the 2nd, 3rd & 4th cores. It took me a couple of hours but I finally discovered a work around. Basically, I had to try and manually pick a driver. With Windows XP the list presented under Intel did not contain the one I wanted. However, by picking another one and then bailing at the confirmation window it would somehow put the right one in for a given core.
    Go figure ....   

  • PC suddenly restarts while playing games MSI 660Ti Power Edition OC 2GB

    Hi,
    I have the following problem since I replaced my graphics card (before 9800GTX+, now MSI 660Ti Power Edition 2GB) I got 3 random restarts while playing games. The computer is not overheating, the CPU's temperature is around 58-59 degrees after running prime95 for 3 hours. The graphics card temperature is 70 degrees after running furmark for 1 hour, the stress tests never failed, just when running games. The computer has been stable. For case cooling im using (2X12cm front, rear 1X14cm below 1X12cm and above 1X12cm +1 X14cm).
    I got two random system restarts while playing Doom 3 BFG and one system restart after playing Wolfenstein for 4 hours. The PC just restarts itself.
    What could be wrong? I have no more ideas? Should I replace the CPU cooler (im running the stock CPU cooler but all stress tests dont show overheating?!)
    Is it possible that the PSU is the reason, but it should be strong enough ...
    The system:
    GA 870A-UD3
    AMD Phenom II 1090T (cooler box)
    MSI GeForce 660Ti Power Edition OC 2GB
    12GB RAM (12GB Kit 3X4GB DDR3 Kingston Genesis 1600)
    Samsung 256GB 840pro
    WD Blue 500GB
    Thermaltake Thoughpower Q-Fan 750W PSU
    Housing NZXT Source 210 Elite
    OS: Windows 7 Ultimate 64-bit
    Thank you.

    The temps for the graphics card are quite normal. I have the same one and under load it will go to 70 to 75C, depending on ambient. What Nvidia driver are you using? Did you do a new driver installation?
    If I look at your CPU though, then you are very close to the max CPU temp and throttling may invoke the shutdown    http://products.amd.com/en-us/DesktopCPUDetail.aspx?id=640&f1=&f2=&f3=&f4=&f5=&f6=&f7=&f8=&f9=&f10=&f11=&f12=
    62C is max.
    Could also be your PSU that's not completely stable and continuous power draw may cause Overcurrent or overtemp protection. Speculating here as to probable causes.
    Another possibility is your RAM. That should normally be paired in 2's. Have you tested with only 2 modules ? Remember we don't support that MB here, but its just another test I would run. But you would know, probably having run it like that with the previous GPU.

  • MSI 670 POWER EDITION SLI HELP!

    Okay so i recently bought another MSI 670 Power Edition card. I loved my original and wanted a bit of a performance boost.
    I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
    So after a few days of testing i get about 10-20fps increase in certain games. Now after comparing my PC to other Computers with similar specs and my cards are faster than theres.
    I am not getting that much of an improvement as i should.
    On unigine Valley "Everything max at 1920x1080" i get a score of 2333 thats with both cards. To me that seems rather low or am i being silly. Also i was watching a video of a guy running the Metro Last Light benchmark and he was hitting over double what i had in terms of FPS.
    Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly. Any help would be awesome THANKS :D

    Quote from: rydek on 14-July-14, 02:34:20
    I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
    Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly.
    As flobelix stated before, you are limited to PCI-E 2.0 because of your Sandy CPU.
    Talking about bandwidth, SLI with PCI-E 2.0 x8-x8 is the equivalent of PCI-E 3.0 x4-x4.
    Not very good, but not very bad either.
    Quote from: rydek
    unigine valley sli - 2349
    unigine valley single original card - 1718
    Tomb Raider Tress FX off everything Ultra average FPS 62.7 - SLI
    Tomb Raider Tress FX off everything Ultra average FPS 36.3 - Single GPU original
    Your scores are ok.
    With a better CPU (i7 3770K), the scores are around 2200 (single) and 3000 (SLI).
    Those with higher scores have overclocked GPUs (and CPUs).
    Tomb Raider is one of those few games with great SLI scaling (most of the games are not).
    As you can see, you get a 70-75% boost in this game.

  • MSI GTX570 POWER EDITION helppp

    Hi, I just bought my MSI GTX570 POWER EDITION from amazon. And it seem to be some problem about this card. It runs poorly on the 3d mark11. And on starcraft2 it recommend the setting to only "meduim, suggested for 258VRM" but aren't the gtx570 is equipped with 1280VRM. Is there something wrong with my card? I have updated all the newest drivers already.
    3d result  http://3dmark.com/3d...8UuRNSxXxfNyXL9
    print scr http://tinypic.com/r/xm5wz8/7

    Quote from: freshlemon on 26-August-11, 12:27:02
    it says, "Your Score is Low Compared to Similar Systems.
    There may be a problem."
    is there anything i can do to improve the performance?
    It's not low, as you can see the most people with the same card has the same scores and they are into the same big graph as you
    Quote from: freshlemon on 26-August-11, 12:27:02
    is there anything i can do to improve the performance?
    Overclock CPU or install fastest CPU or OC the GPU further or both

  • MSI 7750 Power Edition OC.. Overheating .. please help.

    i bought msi 7750 power edition. it's idle temp remains constant at 39` and while playing games like darksiders, temp reaches 79` even with moderate or low settings. the fan on such temp reaches max speed .. 99% and makes it really noisy. is the temp normal or is there any defect wid my piece ? .. Please Reply

    Temp is absolutely normal under load. Anything below 9ß°C is nothing to worry. Try using Afterburner (>>How to use MSI Afterburner<<) and start Kombustor out of it to check tempa under maximum load.

  • MSI GE70 Power Button LED is Solid Orange

    Hello,
    My MSI GE70 power button LED is glowing solid orange as of an hour right now, is this normal?

    Quote from: Satanlygun on 26-July-14, 22:01:07
    It does this every few seconds and it just worries me a lil. Just hoping it's nothing serious. I haven't noticed anything wrong software wise but, could it be telling me something is wrong internally hardware wise?
    Thanks
    Do you have MSI Afterburner, GPU-Z, AIDA64, or any other programs that MIGHT check the GPU's on your notebook? If so, close them. See if it continues happening.
    You can also enable the "Display GPU Activity Icon in the Notification Panel" in your NVidia control panels -> Desktop -> Add a checkmark next to "Display GPU Activity Icon in the Notification Panel"
    This will add a small box down in your notification panel (by your clock) and you can mouse over it to find out what program is causing your GPU to get enabled. This can help debug the problem as well.

  • MSI GTX660TI Power Edition problems

    Hi all,
    I have a problem with Battlefield since I have installed my new GPU the MSI GTX660TI Power Edition.
    I have a Acer Aspire i7, with 6GB memory and a Corsair GS 800W, Windows 7 Home Premium
    Since I have installed my new GPU my game freezes and my systems tells me that there had been a problem with the Nvidia Windows Kernel mode and that it has been restored.
    It happens with both BF3 and BF4....while typing this topic message the same thing happens.....
    It also says Directx error....but I have the latest drivers....
    Could it be the Bios, mainboard or is my GPU not working as it should?
    Thanks for your help.

    List full system specifications, read >>Posting Guide<<

  • Msi 975x power up editon

    msi 975x power up editon  support fsb 1333 intel cpu????????

    Quote from: prozik on 11-February-07, 18:44:59
    guys look at this link http://event.asus.com/mb/fsb1333/ asus support that bu msi???
    Well, if the Asus PW5 DH can support FSB 1333, there should be nothing to prevent the 975x PowerUp to support it. It will be interesting if MSI release a FSB 1333 BIOS compatible, because at this speed (333 x 4) I have the reboot problem in all its (infamous) glory...

  • MSI 975x Power Up Edition, W-64bit, Dual Core Centre won't install

    I have the following setup
    Motherboard   MSI S775 Intel 975X ATx Audio Lan power Up Edition
    Chip      Intel Core 2 Duo E6400 Socket 775 2.13GHz
    Chip Fan                QuietPC SCYTHE Ninja-Plus Heatpipe
    Grapics Card   XFX GeForce 8800GTX 768MB DDR3 PCIE Dual DVI TVo
    Case      Thermaltake VA7000SWA Shark Aluminium Full Tower - Silver
    Power Supply   Tagan 800W PSU - Dual Engine
    Ram      Corsair Memory 2X1GB XMS2-6400 240 DIMM UNBUFFERED PRO DDR2 LED
    Network Card   Buffalo Airstation 125* High-Speed Wireless Desktop PCI Adapter + AOSS
    Hard Drive   2x  Western Digital Caviar 250GB S300 16mb 7200rpm
    DVD Writer   NEC 18X DVD+/+RW/12X RAM IDE LabelFlash Silver OEM
    Windows      Microsoft Win XP Pro 64B OEM & Vista Upgrade Coupon
    The problem I have is that when I try and install the Duo Core centre I get the following VBIOS error
    Flash_MMIO_MAP DeviceIoControl error
    twice before starting the Install wizard. The wizard works and asks me to reboot. After reboot the App won't work at all. I have uninstalled and installed a few times but to no avail. Is there anything else I can do.
    Many Thanks

    Quote from: DryHeat on 08-February-07, 04:45:21
    Support OS: Windows XP/2000/Vista
    Does not support x64 and you are better off without it.
    Quote from: manitou153 on 02-June-07, 22:40:10
    I have the same problem with this following error trying to install the Dual Core Center 2.0.0.6 : "runtime error. Could not call proc".
    How can I fix the problem ? I use Windows Vista Ultimate Edition 64.
    In other words, MSI Dual Core Center does not support Windows Vista 64.  You can try CoreTemp, but again since you have x64 you need to read this:  http://www.alcpu.com/forums/viewtopic.php?t=211

Maybe you are looking for