MSI 770-C45 DDR3 1600 Problems

Hi people,
                Sorry if this is a common problem but did look through the forum but couldnt quite find a problem like mine.
I have followed custom pc computer build for a gaming rig and have had hang ups randomly which allow me to do nothing but switch off system.
 To cut a long story short i have tried everything to fix this but now it seems to be running ok as i have changed settings for ram to 9-9-9-24 and timing to 2T.
I have also set the volts up to 1.77 (or nearby) but i am wondering if this is correct thing to do. I am stress testing it now with prime95 and hoping these setting are correct.
M/B=msi 770-c45
Mem=corsair dominator ddr3 1600 (2 sticks in same colour port which is blue)
Proc=AMD athlon II 2 pro

If the system is stable, then dont change anything.
An AMD-cpu does NOT support 1600MHz -- that is, the memory controller can handle 1066MHz or so. If you set the memory frequency higher, then you are overclocking the system which may result in freezing or other system problems. By losening timings a bit (9-9-9-24 2T) you solved it. Now, keep on testing. If the lot stays stable, then don't change anything else.
Also, use CPU-Z to see what timings/frequency-combinations your memory can handle.

Similar Messages

  • Msi 770-C45 problem. not posting

    Dear MSI,
    i have got exact same problem as in https://forum-en.msi.com/index.php?topic=129732.0
    when i start computer cpu, gpu, psu everything works but nothing shows up on monitor. it's not gpu problem. i tried everything, no result. what's more interesting, when i switch off power supply and switch it back again, computer starts automatically. i thought it was because of power button, but no. any ideas? thanks!
    -mobo: msi 770-C45
    -cpu: AMD Phenom2 x3
    -ram:  mushkin ddr3
    -psu: OCZ 600 MXSP

    Do you also have a vga? What means Mushkin ddr3? Number of sticks? Mushkin Model? Exact cpu model name?
    Also we won't read through that old thread so describe for yourself. As you are saying dear MSI let me remind you that this is a Users-to-Users Forum so you are not talking to MSI.

  • MSI 770-C45 with TV turner card problem

    My problem is that  it will freeze up after I start the TV turner program.  I have tried two different TV turner cards, both are of PCI-E 1X interface.  Both TV turner works fine in other motherboard of 780G chipset (Vista or Window 7).  Currently I am using Mygica 8557 in a 64 bit Windows 7 environment, the computer will freeze 30 seconds  after the TV software (TotalMedia) start . However, I can ran 3DMark2006 without any problem.  Before using Mygica 8557, I use another TV turner PE186Q , the case is even worse, the computer will freeze during driver installation (Vista 32bit) .  But the same card work fine with another brand 790GX motherboard.
    I would suspect it is the IRQ problem but since there is no adjustment option for PCI-E resouces in BIOS, there is nothing I can do.
    Did anyone have the same problem like mine ?
    My config is as follow :
    Phenom II 545
    MSI 770-C45
    G. Skill DDR3-1333 2G x 2
    WD 320G hard disk
    ATI 2600XT
    Corsair cx400 400W power supply
    MyGica 8557 , Grandmars PE186Q

    Quote from: sparkeh on 23-January-10, 22:31:51
    Thanks for all the advice.
    Tried with 1 stick and the system was alot more stable, no BSOD's or any kind of freezing.  I ran prime95 overnight with 1 stick and all was fine, if I insert another stick the system is still stable but I get an error in prime95 after a few minutes.
    [Jan 23 12:02] Worker starting
    [Jan 23 12:02] Setting affinity to run worker on logical CPU #2
    [Jan 23 12:02] Beginning a continuous self-test to check your computer.
    [Jan 23 12:02] Please read stress.txt.  Choose Test/Stop to end this test.
    [Jan 23 12:02] Test 1, 4000 Lucas-Lehmer iterations of M19922945 using FFT length 1024K.
    [Jan 23 12:03] Test 2, 4000 Lucas-Lehmer iterations of M19922943 using FFT length 1024K.
    [Jan 23 12:06] Test 3, 4000 Lucas-Lehmer iterations of M19374367 using FFT length 1024K.
    [Jan 23 12:07] Test 4, 4000 Lucas-Lehmer iterations of M19174369 using FFT length 1024K.
    [Jan 23 12:10] Test 5, 4000 Lucas-Lehmer iterations of M18874369 using FFT length 1024K.
    [Jan 23 12:10] FATAL ERROR: Rounding was 0.5, expected less than 0.4
    [Jan 23 12:10] Hardware failure detected, consult stress.txt file.
    [Jan 23 12:10] Torture Test ran 8 minutes - 1 errors, 0 warnings.
    [Jan 23 12:10] Worker stopped.
    I am in the process of buying a new PSU, the system is so unstable with all memory slots populated.
    Quote
    Tried with 1 stick and the system was alot more stable, no BSOD's or any kind of freezing.  I ran prime95 overnight with 1 stick and all was fine, if I insert another stick the system is still stable but I get an error in prime95 after a few minutes.
    Re-test the each stick alone. [You may have defective stick]
    If each one is stable at his own, before fill all 4 DIMM's:
    * Leave Memory timings to Auto
    * Ensure 2T is used
    * Drop memory freq. to 1066
    * Apply memory voltage recommended by memory vendor

  • MSI 770 c45 audio driver install problem

    Good day,
    I have built a system consisting of
    MSI 770 c45 mb
    Athlon II 245
    4 gigs ram markvision
    1000 gig (storage) and 320 (os) hitachi hd
    9400 gt video card
    media card reader
    dvd burner (liteon)
    generic case and power supply
    the problem I am getting is that I have installed Windows xp with sp3 slipstreamed and I am getting problems installing the audio drivers from either the cdrom that came with the mb or from msi website. Lan & system drivers are installed.
    I have upgraded the bios
    I have booted up with Ubuntu 9 live cd and I can get sound. which means the audio section of the mb is ok.
    I have tried to install the driver in safe mode and still no luck.
    Help!......... I have no idea what to try next.

    https://forum-en.msi.com/index.php?topic=115476.0

  • MSI 770-C45 power problem

    Hi. I have a problem with my MSI 770-C45. When i turn on my computer, nothing happens. On motherboard only 1LED is ON.
    CPU: AMD Athlon X2 240
    MB: MSI 770-C45
    PSU: Corsair VS450
    COOLER: Fera PRO
    GPU: GeForce 7300GT
    RAM: Kingston 4GB and 2x2GB
    All fans are working. When i turn it on, i can't turn it off (power button) .
    What is problem?
    Sorry for my English, but i'm from Poland.

    remove the RAM and reinstall it as miss seated RAM is common to happen (press them down on both corners at the same time till both catches on each DIMM slot click into place)!
    also have you connected the 4 pin CPU power connector?

  • MSI 770-C45 locking up/blue screening/other errors on boot

    I recently built a new HTPC and have been having allot of problems getting it to boot.  It may take 10-15min of trying to boot up over and over with random blue screens, lockups, or errors that the C drive needs to be checked for consistency before Windows will finally load up and work.  At first I thought it was a bad drive, but according to Western Digital’s HDD Diag util, both the controller and the drives surface checks out OK.  I just wiped the drive out and reinstalled Windows 7 again, and this time went with IDE instead of AHCI, hoping it was a driver issue.  It only worked well for a day before the same problems started rearing their ugly head again.
    At this point I don’t know if I have a memory issue, a CMOS setting wrong (which are All Auto), or what.  I hoping someone here might have an idea of what this problem could be.   
    My system specs: 
    MSI 770-C45 Motherboard -  BIOS v1.9 05182010
    AMD Phenom II X4 945 Deneb 3.0GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 95W Quad-Core Processor HDX945WFGIBOX
    4GB RAM – Memory Master-2-Pack 2GB PC3-10666 DDR3 DIMM Memory Kit-MMD4096KD3-1333 SKU: 9360032
    MSI R4550-MD1GH Radeon HD 4550 1GB 64-bit GDDR3 PCI Express 2.0 x16
    Drive C: - Western Digital 320GB WD3200AAKS
    Drive D: - Western Digital 1.5TB WD15EARS
    Linksys WUSB54GC v3 Wireless USB Adapter
    Windows 7 64bit Enterprise
    All recent MSI 770 and Radeon Drivers

    Quote from: Mavrick007 on 23-July-10, 02:39:51
    According to MSI, my motherboard supports the following modules:
    DDR3 800/1066/1333/1600*(OC)
    http://www.msi.com/index.php?func=prodmbspec&maincat_no=1&cat2_no=171&cat3_no=656&prod_no=1812
    This are the speeds of the DDR 3 RAM supported ,1600Mhz beeing done with overclocking ,because the CPU memory controller is no able to do 1600 by default.
    Quote from: Mavrick007 on 23-July-10, 02:39:51
    When I look at the test results for my Motherboard:
    http://www.msi.com/uploads/test_report/TR10_1812.pdf
     I see 1333 RAM list like PC11000 DDR III RAM (DDR-1333).  However, If I go to a site like Bestbuy or NewEgg and search for DDR3 1333, it shows results like Corsair - 2-Pack 2GB PC3-10666 DDR3 DIMM Memory Kit.  I see PC3-10666 and PC3-10600, but nothing for PC11000.
    The only mention of 1333 modules on the test report is for 1333 OC
    When you see the PC 11000 DDR3 or PC3 10666 specifications they are refering to the theoretical bandwidth ,it s related to the frequency of course ,but it s something else it s a data rate.Its wikipedia but it s good enough -> http://en.wikipedia.org/wiki/DDR_3 Some specs are atipical like 10666 ,marketing thngyes
    Search the internet for memory that works ok with your CPU ,look for "real" DDR 3 1066Mhz or DDR 3 1333Mhz."real" means that that memory should be able to run at those frequencies without voltage increase over the default one.Usually when a memory vendor says you need to increase voltage for a specific frequency it means that you overclock and that there is no warranty they will work in your configuration.
    So you need DDR 3 1066Mhz or DDR 3 1333Mhz ,it needs to be AMD tested memory and it needs to be a known to work RAM on MSI motherboards timings wise.Look up on newegg and see what works.
    The performance gaps between 1066 and 1333 are small in real practice and you can overcome some loss by using a "real" DDR 3 1066Mhz , tweaking different timings ,using Command Rate of 1T for example ( you may "feel" it smoother in desktop than a 1333Mhz at 2T).

  • MSI 770-C45 - Windows Install stuck on 'system is starting windows'

    Hello,
    I am trying to get a machine setup, everything seems to be booting fine and nothing wrong hardware wise.  When I attempt to install Windows XP Pro SP1 or Windows 7 Pro, I don't get to the 'select partition' step.  It gets stuck on 'system is starting windows' each time.
    I have flashed the bios to the latest (1.4) and it didn't help it either.  When looking online I just find too many individual problems and answers to this issue.  I am at work now so when I get home I will update with more info as well as try a few more troubleshooting steps.
    -MSI 770-C45 AM3 AMD 770 ATX AMD Motherboard
    -AMI Rev 1.4
    -AMD Phenom II X2 545 Callisto 3.0GHz Socket AM3 80W Dual-Core Processor Model HDX545WFGIBOX
    -OCZ Gold Edition 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1066 (PC3 8500) Model OCZ3G10664GK
    -BFG Tech BFGEGTS2501024DE GeForce GTS 250 1GB 256-bit GDDR3
    -Antech (Will update the power supply later when I get home)
    -Maxtor 500GB Sata 3.0 (7200 RPM?, again will check when I get home)
    -LG dvd+/-rw drive
    -Still attempting to install the OS
    Thanks,
    Steven

    Couldn't edit post so just posting again with the real specs:
    -MSI 770-C45 AM3 AMD 770 ATX AMD Motherboard
    -AMI Rev 1.4
    -AMD Phenom II X2 545 Callisto 3.0GHz Socket AM3 80W Dual-Core Processor Model HDX545WFGIBOX
    -OCZ Gold Edition 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1066 (PC3 8500) Model OCZ3G10664GK
    -BFG Tech GeForce GTS 250 1GB 256-bit GDDR3 Model BFGEGTS2501024DE
    -Antec 500 W PSU Model EA-500
    -Western Digital 500GB SATA  Model WD5000CSRTL  (Originally attempted the install on a IDE 200GB Seagate but that failed as well)
    -DvD drive: Magicspin  Model DVDRW 1016IM
    As a note, I am troubleshooting a friends computer that he was setting up.  Further troubleshooting steps by me:
    Fredrik, I was unable to find the speed/memory handling option in the BIOs to change it down to UDMA2.
    I don't have a spare set of DDR3 Ram to test that out.  Have a spare PSU to test with but haven't done that yet.
    Switched out the DVD Drive to a Lite-On IT Corp. Model LH-52C1P DVD burner and it got stuck on 'Setup is loading files (Windows Executive)'
    Attempted to switch out the IDE Cable for the DVD Drive and found I couldn't put a new one into the Motherboard.
    Seems two pins (one over the other on the far left side) are bent just a little out of place and are loose.  Looks like I might need to exchange the board for a new one by the looks of it.

  • MSI 770-C45 Gameport compatibility

    The problem:
    I have an MSI 770-C45 mainboard and want to use the gameport on an Ensoniq ES1370. I can't get it to work in any way. I think the cause may be the mainboard reserving hardware address 201 for its own purposes (at least Windows XP tells me so, range 0x201 - 0x201 conflicts with "Motherboard resources" twice). Am I correct on this? Is there any way to get the gameport to work?
    Introduction:
    Hello MSI HQ forum users , I am meneer from the Netherlands. I'm 19 years old, male, christian, music-lover and I like tinkering with computers. I hope you'll be able to answer my question .

    Woah! What a lot of replies, quite an active forum!
    Quote from: Svet on 21-May-10, 06:21:26
    Read >>Posting Guide<<
    Try move the card to another PCI slot[board has 3 of them]
    Sorry, got a bit lost in all the sticky posts . Here goes:
    MSI 770-C45 mainboard
    CPU: AMD Phenom II X3 720 / 2.8 GHz
    Memory: OCZ Platinum AMD Edition Dual Channel Kit - 4 GB ( 2 x 2 GB ) - DIMM 240-pins - DDR3 - 1333 MHz / PC3-10666 - CL7
    Video card: SPARKLE SXX260896D3S-VP - Nvidia GeForce GTX 260 - PCI Express 2.0 x16 - 896 MB GDDR3 - DVI
    Harddrive: Samsung SpinPoint F1 Desktop Class HD642JJ - 640 GB - intern - 3.5" - SATA-300 - 7200 tpm -buffer: 16 MB
    Power supply: CoolerMaster Real Power M520 Modular PSU - ATX12V 2.3/ EPS12V 2.91 - 115/230 Volt - 520 Watt
    Optical drive: Samsung Super-WriteMaster SH-S223Q - DVD±RW (±R DL) / DVD-RAM - 22x/22x/12x - Serial ATA- 5.25"
    Operating system: Arch Linux 64-bit, Windows XP Home SP2 32-bit
    And I'll try the moving suggestion.
    Quote from: Henry on 21-May-10, 06:29:22
    That thing must be more than 10 years old and drivers are probably no good for XP. Creative took over the company so you would need to check with them if there are updated drivers.
      http://us.store.creative.com/
    It works flawlessly under XP (Professional) on another computer with an AMD processor, though that computer is less recent . Think Athlon 2600+, GeForce FX5200 and so on.
    Quote from: Stu on 21-May-10, 06:35:50
    Why do you need the gameport? If its for a game controller, why not treat yourself to a modern USB one? As Henry says, I've not seen any devices that connect to a gameport for 10 years or so now...
    There is that; it may not be worth the effort to get the old gameport gamepad working.
    Quote from: Mike on 21-May-10, 07:37:29
    Yes, there are converters.
    >>>Gameport to USB adapters<<<
    =) Those are more expensive than a shiny new USB gamepad.

  • MSI 770-c45 wakeup on lan

    I saw in bios that board have wake up event setup for lan, mouse, keyboard usb, and etc but I did not make anything to work. When I shutdown computer, board just switch off everything, no power on mouse, keyboard, lan on switch goes off.
    Does msi 770-c45 is working with wakeup events or those options in bios are there just decoration?!?
    Thanks for help!
    P.S. before MSI I had Gigabyte board witch worked fine wol

    Thanks for trying to help!
    I did not reinstall windows, I have win7 and winxp. Win7 have all drivers by default so switching board was really easy there. Anyway I think its not win problem, as I said when I shutdown computer, board just switch off everything, no power on mouse, keyboard, lan led on switch goes off. To wake up board on event from device you need power, so wake up on keyboard and mouse also does not work, no power, I switch them on in bios of course.
    Long time ago boards had jumper which you needed to put if you wanted wake up on keyboard or mouse, without jumper no power like in my case. With out led ON on my switch wol will not work that's for sure. Its really looking that board is missing power management for wakeup events, but I cant believe that is true as today every board have wol by default. Old cheap boards which I have in my company have wol, every single board so far which I saw have wol, MSI did not implemented in MSI 770-C45 ?!?
    Regarding S3 I dont know.
    This could be important to, mouse is on USB and keyboard is on PS2, so there is no power on USB or on PS2?!? Strange!
    Mobo: MSI 770-C45
    Proc: X4 930
    PSU: LC power 600W
    GPU: MSI 5770 1GB
    RAM: DDR3 4GB (2GBx2 GEIL 1600Mhz)
    HDD: 2x WD.

  • MSI 770-C45

    hi.
    cpu: amd ph.2 955 b.e. 3.2ghz w/ scythe katana 3 hs/fan
    m/b: msi 770 c45 am3
    ram: G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit
    psu: APEVIA ATX-AS680W-BL 680W ATX12V / EPS12V SLI Ready Power Supply
    vid: MSI 9800 xt oc 512 (known to work, using it now)
    put this together last night, it's my 8th pc build but 1st am3/ddr3. it will not post. tried ram in all
    ways (single and double). the m/b has 4 blue led lights that are all lit so i suppose the power is good. can't get to bios to see if cpu is doa. any suggestions? i don't get any beeps from speaker.
    edit: btw my old m/b (nforce 4) had a separate 4pin power(not to be confused w/ the 6pin on card) connection for the pci-e slot. i cannot find this on this m/b so i assumed it doesn't require it.

    i got my rma'd m/b back. it works great. had to place 1 2gb stick in dimm 3 to get it to post though. the manual says to use 1 stick in dimm 1 to ensure successful post. obviously this is incorrect. overclocks great btw... my phenom II 955 b.e. is running @ 3.8 ghz and still idles 38 celsius 55 full load

  • MSI 770-C45 Mobo Video Failure

    Hey all!
    Here's what I have
    MSI 770-C45
    AMD Phenom II X2 550
    1GB Crucial DDR3 1333 X2
    GeForce 8500GT
    My problem is that when I boot, I have no video. I threw in a PCI graphics card but still no video.  It's kind of embarrassing but I'm not sure where to go next. 
    Thanks for the help.

    This is the first I've ever put this together.  However I have seen the video card work. 
    PSU ThermalTake Pure Power 430 - worked on the computer I'm using right now.
    The CPU  power cable is connected.
    No I haven't tried to boot w/o the m/b in the case.  I will though.

  • MSI 770 C45 won't post.

    Hello,I just bought and built my new PC but it won't boot, the fans and the LED on the motherboard will turn on but nothing else happens, no beeping noise and the display gets no signal and the reset and power buttons nor the LEDs won't work. And when I plug my 4 pin connector to the motherboard it won't start at all.
    My PC:
    Amd Phenom II x4 955 3.2 gh
    MSI 770 c45
    Kingston ValueRAM 2GB DDR3 1333MHz CL9 Dual Channel Kit
    HIS Radeon HD4850
    Samsung 500GB SATA-II 7200 rpm 16MB SpinPoint F3
    Seasonic S12II-520 Bronze 520W
    I've searched the other posts, but I've already done that and it still doesn't work. And I think my PSU is more than capable to deliver the power for this system.

    Quote from: Humpy on 29-April-10, 07:08:26
    It did work outside of the case, my display turned on and I was too lazy to plug the PCIx connector to the graphic card and I started installing the mainboard back to the case, and now I get the same black screen with or without the PCIx connector plugged. But now I can start the PC with the 4 pin connector in, all the 4 blue LEDs on the motherboard are on and the power LED on the case is on too now. And I can turn off the PC by holding the power button.
    When mounting the board to the PC case take attention to this one marked with red:
         Motherboard Grounding to case causing No Post
    Test the motherboard outside of the case to verify that the motherboard is not shorting to the case and causing a problem
         •    With only the CPU and heat sink, memory, and video card (or onboard video) connected to the motherboard, place the motherboard on a non-conductive surface and retest the motherboard
         •    Check the case mounting standoffs to verify that they are lining up correctly with the mounting holes on the motherboard.

  • BIOS settings for MSI 770-c45 - overclocked with a Phenom II 550 Black Edition

    Hi,
    Wish I could say I knoew what these bios settings are, but I can't - I really need some help here.  Anyone who has this m/b knows that there is a dip switch to help you get a 10%/20% perf increase, but it fails for me...
    Anyone have some advice onthe appropriate settings?
    Many thanks,
    Sayer

    here's mine:
    Phenom II X2 550BE@4ghz
    MSI 770-C45 bios 1.3B2
    Team Xtreem DDR3 1866 C8 running DDR3 1550 7-7-7-21@1,8v
    cooling Thermalright Ultra 120 extreme, dual fans
    bios settings (Cell menu only, I dont think the others setting would affect)
    * AMD Cool N' Quiet--->disabled
    * CPU Fsb freq--->230mhz...might different with yours, depend on your CPU though
    * CPU Ratio--->17.5
    * CPU-NB Ratio--->x9
    * EC Firmware--->normal
    * Advanced Clock calibration--->disabled
    * Auto Overclock--->disabled
    * multi-step OC booster--->disabled
    * HT link control--->x9
    * vcore--->1,55v (must use good cooling with this voltage)
    * vdimm--->1,84v
    * NB voltage--->1,2v
    * CPU-NB voltage--->1,33v
    other setting are all auto

  • MSI 770-C45 3 long beeps

    hello i am bad in english but i have Nvida GeForce G100 and MSI 770-C45 and AMD Athlon II X2 250 and no ram in slott but i get 3 long beeps what is tath? and black screen, but without ram wil not screen comes up?

    Quote from: super2277 on 02-October-10, 09:12:33
    i read in bios and that ddr3 ram is down clokked to 1066Mhz self
    Quote from: Mark on 25-September-10, 04:43:27
    The memory controller on the Athlon II X2 CPUs support up to 1066mhz RAM so might I suggest a 2 x 2GB 1066mhz kit.

  • MSI 770-C45 - MAC address 00:00:00:00:00:00

    I've just upgraded my system around an MSI 770-C45 motherboard.
    I've noticed that the MAC address of the onboard RTL8111/8168B is 00:00:00:00:00:00.
    Is there a way/utility to reset the MAC address in the ROM ?
    The BIOS has been updated to V1.30, but this did not resolve the problem.
    Thanks.

    other than re-installing the net card driver you could try this utility to change the mac address to any one you like:
    http://www.technitium.com/tmac/index.html

Maybe you are looking for

  • How do I find Ibook audio files on Mac?

    An Ibook that i downloaded includes audio, i would like to be able to listen to the audio on my ipod instead of an ibook. Is it possible to transfer the files to itunes?

  • Photoshop brush strokes are smaller than the cursor, need to make them the same.

    My photoshop brush, pencil and Clone strokes are smaller than the cursor, which makes it very difficult for accuracy. Don't know what made them change, but want the cursor and stroke to be the same. I've tried different settings in the brush dialog b

  • Liaison imprimante

    Bonjour Impossible d'imprimer en liaisin avec ma borme AirPort Express Ma configuration -routeur NETGEAR 2200 -imprimante EPSON pro 4800 ( traceur) connectique USB -gestionnaire des machines OS X.6.8 -driver de l'imprimante..le dernier en date de EPS

  • Alternatives for 377 Processor

    I was trying to install GarageBand, but I'm running an iBook G3 with only 377 MHz. I'm told that no version of GarageBand will work. I'm just trying to run a MIDI controller (keyboard) on this Mac.

  • Take the phone and run?

    When I pick up my reserved phone at the Apple store tomorrow, is it required that they activate it for me, or can I pay for it, leave, and activate at my leisure myself?