MSI 770T-C45 won't post after flashing BIOS with M-FLASH

After flashing AMIBIOS 8.3 to v8.7 with M-FLASH via USB stick I can't get any post.
Had I read this forum before I wouldn't have done it, but here I am.
Fan starts, LEDs are off, no beeps at all, power button does nothing. Black screen.
After force flashing (yes, I am THAT stupid) the prompt said it would reboot in 5 seconds and after that nothing.
Here's my setup:
Board: MSI 770T-C45
Original Bios: v8.3
Flashed Bios: v8.7 (flashed with M-FLASH)
VGA: EVGA NVIDIA GeForce GTX 660
PSU: Enermax FMAII EG465AX-VE 460W
CPU: AMD Phenom x4 9650
MEM: Kingston DDR2-667 4x2GB KVR667D2N5/2G
HDD: SAMSUNG 840 SSD 250GB
OS: Windows 8 Pro 64bit
I tried every CMOS clearing method found in previous posts and threads (including this and this.)
1. Unplugged from power, waited 5 minutes, removed the battery (5mins), changed jumper position (5min), switched it back (5min), plugged it in (5min) and powered up with and without USB stick in the hub next to network hub with old BIOS (v8.3) inside. Pressed CTRL+HOME, anything, not a single message or beep or LED flashing.
Also I removed all RAMs and kept one in the first socket. Nothing.
I really don't know what to do next. What seems to differ from other users is LEDs non working, what does that mean?

The problem here is that after update 8.6 the m-flash module was updated, so yes your mobo is a brick, but there is still hope for it. I had the same situation a few days ago with the exact same model and was able to recover it by following the steps on listed on the below posts:
https://forum-en.msi.com/index.php?topic=133578.0
https://forum-en.msi.com/index.php?topic=129989.0
It may seem complicated at first, but trust me its not at all.
Anyways you probably already have another mobo, send it for RMA or used it as frisbee, but it may come handy for some other doing the same noob flashing as we did

Similar Messages

MSI 770 C45 won't post.

Hello,I just bought and built my new PC but it won't boot, the fans and the LED on the motherboard will turn on but nothing else happens, no beeping noise and the display gets no signal and the reset and power buttons nor the LEDs won't work. And when I plug my 4 pin connector to the motherboard it won't start at all.
My PC:
Amd Phenom II x4 955 3.2 gh
MSI 770 c45
Kingston ValueRAM 2GB DDR3 1333MHz CL9 Dual Channel Kit
HIS Radeon HD4850
Samsung 500GB SATA-II 7200 rpm 16MB SpinPoint F3
Seasonic S12II-520 Bronze 520W
I've searched the other posts, but I've already done that and it still doesn't work. And I think my PSU is more than capable to deliver the power for this system.

Quote from: Humpy on 29-April-10, 07:08:26
It did work outside of the case, my display turned on and I was too lazy to plug the PCIx connector to the graphic card and I started installing the mainboard back to the case, and now I get the same black screen with or without the PCIx connector plugged. But now I can start the PC with the 4 pin connector in, all the 4 blue LEDs on the motherboard are on and the power LED on the case is on too now. And I can turn off the PC by holding the power button.
When mounting the board to the PC case take attention to this one marked with red:
     Motherboard Grounding to case causing No Post
Test the motherboard outside of the case to verify that the motherboard is not shorting to the case and causing a problem
   •    With only the CPU and heat sink, memory, and video card (or onboard video) connected to the motherboard, place the motherboard on a non-conductive surface and retest the motherboard
   •    Check the case mounting standoffs to verify that they are lining up correctly with the mounting holes on the motherboard.

MOVED: MSI P45 Platinum won't post after warm boot

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=125291.0

Thanks for the reply DougKmcse
I have no trouble with the overclocking since this is only a minor overclock (2.8GHz), the only problem I have with this is it gets stuck at restart. With that 2.8GHz OC, i have the vcore @ 1.285v which was stable running 1hr Prime95. I just can't understand why it gets stuck during warm boot.. might try to experiment (400x6 = 2.4GHz) when I get home from work to see if the 400 FSB is causing this. And yes, I agree with you that it would be easier to use a lower FSB with a higher multiplier. I just wanted to try having 400 and having a perfect 1:1 ratio. I have some data suggesting a 1:1 (@ 400:400) is better than 1:1.2 or any other divider. I used Everest cache & memory bandwidth benchmark to test this. I got lower "ns" testing my RAMs (PC6400 DDR2 800) during 1:1 FSB:Ratio (400:400) vs 1:1.2 (333:400)

K7N2GM-V won't POST after shut down

Hi all.
I just did my first build on a K7N2GM-V and it won't POST after I shut down. When I hit the power button, PSU does not turn on, fans do not turn on, nothing happens. If I wait about 10-15 minutes, then it will POST and boot normally to my XP Pro SP1. Nobody seems to have had this problem and I am stumped.
Could it be due to my power supply? My PSU is the one that came with the X-QPack, which claims +3.3V(18A), +5V(22A), +12V(20A), -5V(0.3A), -12V(0.8A), +5VSB(2.0A). I don't have a spare PSU to test this with.
Any ideas? Please let me know what additional information might be needed.
Thanks.

Quote from: osnavi on 01-July-05, 07:25:53
What are CPU/system temps. idle/stressed ?
Using PC Alert 4, I saw 39C idle. I haven't stressed the CPU yet.

Macbook Pro won't login after sleep (sleep with low battery -- mac turned off maybe it's called save sleep)

Macbook Pro won't login after sleep (sleep with low battery --> mac turned off maybe it's called save sleep)
So if I hit the powerbutton my mbp booted like it is booting from the save sleep (so very fast and the login screen is there in about 10 sec.and there is no apple logo while booting just the desktop screen in "unsharp" ore foggy however...)
Then when i see the login (if the keyboard backlight turned on) i wand do tipe in my code but it won't work... the trackpad is not working; and when i plug-in a usb mouse the mbp is not powering on the usb-mouse (laser is off)
Why is that this way?
Is there n option to wake up the mbp fromm deep/save sleep without haveing issiues after that?
THX

Sorry for such a long delayed response...
I was able to get to an apple store this past weekend, and let me tell you... I'm about finished with there great "support".
Right before I went to the store, I tried to eject a disk. Well the cloth in the SuperDrive (I assume to protect the drive from dust and such) Pulled up with my disk. So I get the Apple store, describe my problem and what happened with the cloth piece. The "Genius" writes up a form and tells me they have to run diagnostic and it will take a couple days... and I will get a call when its done (1-3 days).
Well on day number 3 I called up the store and they told me it was ready to be picked up? I asked if anything had been fixed and they told me they could not reproduce my "sleep issue", so they couldn't fix that.. but told me the cloth piece in the SuperDrive had been fixed.
I drive an hour (one way) to the Apple store to find that all they did was PULLED OUT the cloth... they did not replace it! So basically I have a hole for a Super Drive.
I asked why I was not called to say that my computer was ready to be picked up... didn't get an answer on that one.
I asked why my SuperDrive was said to be fixed, when nothing was done... they told me that it would have to be sent out to the factory store for that to be fixed (FIRST TIME THEY MENTIONED THAT!) Oh, and that would take 5-7 business days. Well that's not going to happen right now considering I'm a college student that NEEDS a working computer!
So I go home, angry... start just putting all my important documents back on the computer. And the screen starts blinking!!!! I guess now I have the same thing described in another post on these forms...
Lets just say that I'm not very happy with Apple right now! If anybody else has success on either the sleep issue or the screen blinking issue, please let me know!
Thank you!

TS2734 my iphone won't beep after being located with find my iphone

my iphone won't beep after being located with 'find my iphone' app.
battery is fullly charged. the phone is not muted

The phone "beeps" only if "Play Sound" is ON and after clicking "Send" (even if no message). Just locating the phone doesn't make it beep.

MSI X99S XPOWER won't boot after a Windows 8.1 Update

Hi all, two days ago I was using my PC as normally and Windows needed to restart because of an update from Windows Update. It restarted and won't be able to boot again. I get a 04 debug code (Power on South Bridge Initialization) and I've tried clearing CMOS, without SSD/HDD... and there is no way.
I'm reading something about an Intel drivers update that can modify the firmware, do you know anything about it?
Board: MSI X99S XPOWER
Bios: Version 1.4
VGA: MATRIX GTX 780Ti
PSU: Enermax Platimax 850W
Intel Core i7 5820K
MEM: G.Skill 32GB in 4 sticks (8 GB each) @2400 MHz XMP
HDD: OCZ Vertex 450 256GB
COOLER: Akasa Venom Vodoo
OC: 4 GHz 1.15v
OS: Windows 8.1 x64
Thanks

Windows is not corrupted, I've tried that SSD on another computer without problems and in my computer without HDD/SSD and won't boot anyway.
If I'm able to boot with the secondary BIOS, I'll recover the first one by the following steps:
Quote
BIOS recovery with AFUDOS command
When BIOS updating fails or causes the computer non-bootable, you can recover the
failed BIOS by the steps below.
Preparation:
1. Prepare a bootable USB flash drive.
2. Download the latest BIOS file from the MSI official website at www.msi.com, and
then decompress the file.
3. Copy the AFUDE238.exe and the BIOS file to the bootable USB flash drive
BIOS recovery steps:
1. Power off the computer.
2. Set the Multi-BIOS switch to the functional BIOS ROM.
3. Insert the bootable USB flash drive you have made to the USB port.
4. Boot the computer into the bootable USB flash drive.
5. Set the Multi-BIOS switch to the failed BIOS ROM.
6. Execute the below command to flash the BIOS:
For example: AFUDE238 EXXXXIMS.XXX
7. Restart the computer after the BIOS flashing is complete.
Important
Do not use the Multi-BIOS switch when system is booting up.
But I have a doubt with the "Important" note because I need to change from safe BIOS to failed BIOS with the PC booted, right? So I'll use the Multi-BIOS switch with the system up...
Thanks a lot

MSI P55-GD55 Won't post 3 Beeps-Need Assistance

Built many PCs but never had a problem like this. Starting to think MB is bad.
Built this in Dec 2008
MSI P55-GD55
A-DATA Gaming Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600
Intel Core i5-750
OCZ ModXStream Pro OCZ500MXSP 500W
MSI N95GT-MD512Z GeForce 9500 GT 512MB 128-bit GDDR2 PCI Express 2.0 x16 HDCP Ready Video Card
Western Digital Caviar Black WD1001FALS 1TB
COOLER MASTER Hyper 212 Plus Cooler
2 weeks ago PC would do nothing at all after I turned off and then tried to restart. Thought I had bad power supply, but it checked out. Cleared cmos by removing battery and turned off oc genie and that seemed to cure problem.
Left PC on ever since. Had to turn off yesterday to check unrelated network issue and when I tried to restart It won't post. Just get 3 beeps. No video. Nothing. Tried to clear cmos, switch memory sticks, only use one mem stick in slot 1 and I get nothing but 3 beeps. Very unlikely that both sticks are bad. Tried powering on from internal switch and got nothing but 3 beeps. Beeps are less than 1 second in duration so I guess they are short beeps.
Any thoughts are greatly appreciated.
If I have to RMA to MSI how long does it take to get replacement? What do I have to send to MSI, all contents of retail box or just the board?

Quote
If I have to RMA to MSI how long does it take to get replacement?
Quote
I am ready to toss this board and buy another unless I can get this working.
At the moment there is know certainty about the definate cause for your problem. What makes you so sure that the board is the cause (and not your CPU (which hosts the memory controller, after all), faulty RAM sticks (have you tested every single stick of RAM you have in the first slot (check user manual) and cleared CMOS (with A/C power cable unplugged from PSU before each new start-up attempt)?).
A contact problem between CPU Pads and board socket pins could also cause this (please reseat CPU and heatsink). Another possible cause is a short-circuit problem inside the case (test the board outside the case on a non-conducting surface).

770-c45 won´t post.

hi guys!!!
well... yesterday i go to the shop and buy a whole system by parts. i get home to setup everything and i get nothing.
the system turns on with the first led on and that´s all. fans are working and the lights of my case too.
msi 770-c45
amd athlon II X4 640
asus eah5770
4gb kit ocz ddr3 pc3-10666 gold (low voltage)
the psu it's a generic one of "500W".
i asked in the shop about this, and they told me that i shouldn't have any problem with that PSU.
i tried everything already. 1 ram stick in every slot. without video card. without ram, without cpu... out of the case.
nothing changes. always the first led is on. the fans too and no beeps at all. all power cables connected.
i´ve been reading for hours and i just cant find any solution. so any help will be very apprecciated.
greetings from germany.

Quote from: Jack on 31-October-10, 18:27:48
Well, that is what the shop says. It does not mean anything. After all it is a theory, nothing more. What you need to do is an actual test.
yeah, i know that. it will be an issue if the generic PSU doesn't have enough power. but to don't post at all??? even a beep without the ram or anything on it. (it should be)
my first thougth was to test another PSU but i can't, unless i go and buy a new one.
i had read a lot about this MB and this same issue. but i cant find a why or a solution.
Quote
Have you connected the CPU power cable?
of course.

MSI P67AGD55 B3; Won't post

Hello everyone!
I just bought a new system for a friend, and I can't get it to post for some reason. I have built multiple systems before. Here's the system
MB; MSI P67AGD55 B3
CPU; Intel Core i3 3220
Ram; Crucialr 2x4GB Ballistix 12800
PSU; Antex Earethwatts 650W
GPU; AMD 6770
etc etc
Basically system won't post and I went through and tried 1 stick of ram, a different stick of ram in the main slot, no ram, no GPU, no HD etc attached.
When the computer starts it does 4 (i think1 long 3 short?) beeps, reboots, repeat.
Something makes me think it's bad ram but I'm not sure.

Which BIOS is currently on that board ? Check the little green sticker on the BIOS chip and post that.
I suspect that the board still has the initial BIOS versions for Sandy support.
You have added an Ivy CPU and for that you need the new IVY BIOS support series.
To flash the board, you will have to get a supported CPU first, either family or friends or a helpful PC shop.
My personal choice with that CPU would have been a 7 series board in the same price bracket.

MacBook Pro won't POST after 10.6.8

Hello All,
After installing 10.6.8 last night on my 4.1 MacBook Pro, it won't POST. The sleep indicator light comes on briefly and I can hear the optical drive spin a bit, and then it just shuts down. No display, nothing.
Any troubleshooting tips would be greatly appreciated.
I took a quick video of what it does. Here is the YouTube link to the video:
     http://www.youtube.com/watch?v=FiSVZ8OoQR0

denepeek wrote:
I appreciate the link but this sadly wont do us any good . Our Macs wont make it past the power on self test so we can try any of those methods listed.
            Resetting the SMC on Mac portables with a batteryyou can remove
Note: Learn about removing the battery on MacBook and MacBook Pro.
Shut down the computer.
Disconnect the MagSafe power adapter from the computer, if it's connected.
Remove the battery.
Press and hold the power button for 5 seconds.
Release the power button.
Reconnect the battery and MagSafe power adapter.
Press the power button to turn on the computer.
            Resetting the SMC on portables with a battery youshould not remove on your own
Note: Portables that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side)Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer. Note:The LED on the MagSafe power adapter does not change states or temporarily turn-off when you reset the SMC.

I think new mobo (MSI 770T-C45), is causing sleep problem in windows 7.

Hey all, I'm new and first time buyer of MSI mobo.... Finally got way from Biostar and Asus...lol Anyways, I upgraded to a 770T-c45 and so far so good. One problem been having is my PC wont sleep, monitor does but not pc. Before I upgraded everything was fine, so my only isolated cause is to be the motherboard, I think..
I've tried everything in power options.....geesh... I've gone into bios tried a few things there also, but still no change. I wonder if the APS thingy is causing this???
Anyone having this problem or maybe help with a solution.
Btw...i have this XCLEO WInd tunnel tower, and it has 2 huge (super bright) Blue fans on the side and it's really nice to get those to sleep along with pc..
thanks everyone.

Did you set the ACPI standby state to S3? If not, go to Power Management in the bios and change ACPI Standby State to S3.

Msi 770-C45 problem. not posting

Dear MSI,
i have got exact same problem as in https://forum-en.msi.com/index.php?topic=129732.0
when i start computer cpu, gpu, psu everything works but nothing shows up on monitor. it's not gpu problem. i tried everything, no result. what's more interesting, when i switch off power supply and switch it back again, computer starts automatically. i thought it was because of power button, but no. any ideas? thanks!
-mobo: msi 770-C45
-cpu: AMD Phenom2 x3
-ram: mushkin ddr3
-psu: OCZ 600 MXSP

Do you also have a vga? What means Mushkin ddr3? Number of sticks? Mushkin Model? Exact cpu model name?
Also we won't read through that old thread so describe for yourself. As you are saying dear MSI let me remind you that this is a Users-to-Users Forum so you are not talking to MSI.

P7N Mobo won't POST after a month, revisited

recieved new (not really new, it's been installed in something before) mobo from 2nd RMA, still no boot. amazing that the serial number was only sequence numbers away from the original. anyhow, system again 'barebones'd and still no POST. even tried a plain jane PCI video card to no avail. i'm shocked. MSI again offered to RMA, at this point what's the use? i ordered EVGA's model instead. at least they'll cross-ship if there's something wrong.
so, what are my options now except to RMA again? i don't want this board anymore, i'd rather have my dough back but i'm afraid it's $150 up in smoke.
guess i'll go try and find a port80 card from my lab and see if that'll tell me anything, because i'm pretty much done waiting for this thing to ever work right and so far sending it back 2x hasn't gotten me anywhere.

a bit of background:
Firstly, I'm a BIOS architect, so i'm not new to building/debugging systems.
system was originally working in following config: 2x1GB Patriot DDR2 800 (4-4-4-12, 2.1V set via BIOS), Q9300 2.5GHz (no overclock, stock voltages for everything else), 700W p/s, Zotac 8800GT 512MB PCIe 2.0 video, Samsung IDE DVD drive (master in IDE1), WD 40GB IDE drive (master IDE0), Seagate 160GB SATA I (SATA 1 port), PS2 keyboard/mouse, ethernet.
when the WD started to go (the OS disk) i cloned it to an 80GB Seagate SATA II laptop drive i had and ran that until i got a real replacement drive. The 80GB seagate went into SATA port 1 and the 160 moved to SATA 2. DVD i think i moved to IDE0. Things worked fine. New Seagate 250GB SATA II 3.5" drive arrived and i cloned the 80GB to that and swapped it into SATA port 1. THis is where the trouble started.
Upon rebooting, the system didn't come up all the way. I rechecked my drive connections and rebooted. The BIOS posted and indicated it had restored defaults due to 3x failed attempts to boot. (Of course this was only 2 boots, but i didn't pay much attention). I set the memory timing back to 4-4-4-12, 2.1V and checked all others (looked fine) and rebooted. system never posted after that.
Only thing system appears to do is power up and the CPU fan runs. Putting a 4 pin fan has the fan start up fast, then slows down (which to me says BIOS is booting enough to turn down the fan via the fan controller).
Figured it was a p/s issue, so tried one i had laying around, no POST.
Figured it was CPU problem, got a new one and tried again, no POST.
Thought perhaps it was a p/s issue again (the second one i had was pretty old, but came from a formerly working system), bought a brand new BFG 650W and tried again, no POST.
I then tried everything in the troubleshooting guides, removed from system to anti-static mat (i have a wrist 'leash' and the mat is properly grounded to house ground), and tried all combinations of no disk drives, no memory, single memory, tried old PCI video card, all no POST.
RMA'd mobo. They repaired something (didn't indicate what). Got system back, plugged it all back together and powered up, no POST.
Tried all troubleshooting tricks again, no POST.
RMA'd again, this time requested completely new mobo.
Got system back, plugged it all back together and powered up, no POST again!
Ordered EVGA mobo.
Got *another* RMA after talking to MSI tech support live. The only thing that he could suggest is that perhaps the new drive caused some problem to the board. This might be plausible, but SATA being hot pluggable, i wouldn't think that this could be an issue ever, even if i did plug it in while the system was on (which i didn't, every insertion/removal has been with system disconnected from power (removed A/C cable from p/s)).
Does *anyone* have any ideas that i might try?
(This is a system that's supposedly tested ok from MSI, and since i've got a different board coming if someone would like to toss me $100 i'd sell it rather then send it back). I'd rather keep it and get it working since i've spent my hard-earned cash and time on it already, but at this point it's been 6 weeks and i can't be without a desktop for any longer.

Disk Utility won't let me do anything with broken flash drive?

Hi there,
I own an 8GB SanDisk flashdrive that recently, and out of nowhere, changed permissions to write only. I feel like this may have something to do with the fact that when it was in my old Macbook I would close the screen with it still inserted and it would eject itself and the drive has possibly become corrupt because of this happening one too many times? Anyhow, when moving files around and to my new Macbook and what not, I tried to move some from this USB and it wouldn't let me. I eventually worked out that it would let me copy the files and paste them elsewhere, but now I have this flash drive with a bunch of files that can still be read and I don't know what to do with it because it won't let me delete them either. When I try it comes up with "The item can't be moved to the trash because it can't be deleted." I've tried Disk Utility and this is what happens under the First Aid, Erase and Partition options
I've also tried the appropriate commands in terminal to try to get the disk utility to respond and I kept recieving error messages there too. Also, when I click on the volume underneath the disk it shows all the space that all the files that are very much there are taking up but then also says there's zero files.
Anyone know what on earth is going on?! I mean I know the USB has probably just had it but I'm wondering if there's any possible way I can repair or erase it at this point?

I suspect that the USB is dead. This is the result I get when I insert my USB drive formatted the same as yours:
Note that the options are not grayed out.
You might connect it to a PC, if available, and see if there is any difference.
Ciao.

MSI 770T-C45 won't post after flashing BIOS with M-FLASH

Similar Messages

Maybe you are looking for