MSI 845PE Max-L

Is there a compability problem between Radeon 9200 Atlantis,P4 2.66 Gig prosessor and MSI 845PE Max-L ??
Memory module is DDR 400 512 Ram,HD is Maxtor 120 Gig ATA 100
Every single component works fine with my other Motherboard ( MSI 845E Max )
but when I try to start these in 845PE Max-L only thing that happens is prosessor cooler spins 2 seconds...then totally silence....I got a motherboard replaced once
already....
I cleared CMOS
tried another graphic card ( Geforce3 Ti 500 )
Nothing happens even with default settings...
Highly unlikely that two broken motherboards has been given to me !?!?!?!
Please someone tell me what to do..
E-Mail,MSN or here at the Boards...
- THX -

"Lower you DRAM Freq to 333MHz and increase you DDR Voltage to 2.7v, thereafter incrasing your AGP Voltge to 1.6v."
Why ? and how ?
cannot go to BIOS..
and I just asked if there is a compability problem...
Danny : no other cooler movement :(
just prosessorcooler spins few times,
there are no shorts between board and case through the standoffs.
I took motherboard out of case ( in case of that )
Whole F****n thing is starting to me off...
Never had this much problems with MSI-boards :(
So,once again ; every component works in 845E max ,same case,same powersupply etc.
Only sure thing seems to be : 2 broken motherboards ! ( god damn )

Similar Messages

  • MSI 845PE MAX

    i'm using the mainboard MSI 845PE MAX
    does anyone else uses this board?
    i just wanna know if this board can support AGP 8x graphic cards
    can anyone tell me? 

    hello, nope its support maximum AGP 4x. but good news is that you can use any AGP 8x VGA on it without almost any limitation. differents is quite little. only few visual increament. nothink performance related.

  • Does MSI 845PE Max supports LBA

    In fact all is in the title... Does MSI 845PE MAX (6580) supports for LBA drive?

    Yes, as you need to have the patch incorporated in order to recognize the total drive to start with. There is some info here: http://support.microsoft.com/default.aspx?scid=kb;en-us;305098

  • MSI 845PE Max Motherboard TV CARD problems

    hello,
    i'm use to MSI 845PE Max motherboard and avermedia tv card. i'm plug in to avermedia anywhere pci slot in motherboard but not installed avermedia. error is "ACPI bios system motherboard extension" How i can install to avermedia tv card.. HELP ME..!
    PoWeRGuArD

    i'm plug in to avermedia anywhere pci slot in motherboard
    dont understand this bit,try different pci slots

  • MSI 845PE Max Lan - MS-6580 Ver.2.0 boot failure

    I recently purchased this mainboard and components. All's working fine except for 1 strange issue:
    On each 1st boot-up (after I powered down) the harddisk (UDMA 100, 80GB Western Digital) is not detected. This results in a boot failure.
    After this 1st failure I reset and from then on booting is OK, harrdisk is succesfully detected (although it always takes about 10-15 seconds before detecting).
    Anyone else experiencing the same problems?
    This is my config:
    - MSI 845PE Max Lan
    - 2,4GHz P4
    - Western Digital 80GB 7200rpm (set as master, only device on its cable)
    - ATI Radeon 9700
    - 512 MB DDR (pc2700)
    Hope anyone can help out.

    Note: FSB533 CPU is required in order to choose DDR333 selection in the BIOS setup
    thats what is says here
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=364&MODEL=MS-6580

  • MSI 845PE MAX-L mobo no power whatsoever

    Hi,
    Just upgraded my mobo, RAM & processor to the following:
    MSI 845PE MAX-L mainboard
    Intel Pentium 4 2.4 GHz
    DDR-DIMM PC2700 512MB
    Put everything together and worked a treat from Monday. Reinstalled all my software including XP and had everting running smoothly for over 24 hours with the tower boxed up (so no possibility of accidentally touching any componentry).
    This morning I tried to switch on the machine and NOTHING. No response from the mobo no fans no lights no beep - nothing.
    Checked all leads in place.
    Then tried power supply (Eagle ATX 350W Switching Power Supply Pentium 4 compatible) on my old ABIT mobo together with my old 256 Mb SRAM & Hercules 3D Prophet 32MB graphics card. It worked!
    So put same setup back on the new MSI mobo, i.e. just graphics card, 512Mb DRAM, power supply & Intel 2.4 processor. Still nothing. Pretty sure got all my leads from the tower in all the right places on Mobo as they matched the previous configuration and that wouldn't have worked before, right?
    Whats going on, why does my pc work one day and then can't be arsed the next?
    Lloydich

    I had an Eagle 350watt PSU come supplied in my new case but i didnt trust the PSU so i took it out without even trying it.
    What is your complete system build setup?
    Those el-cheapo PSU's are not really upto running the most intense of systems despite what the manufacturers say.
    Unplug a few components from off the PSU and try to boot up again... its not impossible the PSU is dead... honestly if you spend alot of money on a new system it seems criminal not to get a decent PSU, im not criticisng here im just surprised how many people dont consider getting a 'good' PSU to power their new state of the art PC's.
    Try the unplugging of a few components that connect to the PSU if this dont work for you then if possible try a better PSU (350 watt does not neccesarily mean its good, some cheap 350 watt PSU's are less powerful than a good 300 watt PSU)

  • Have the MSI-845Pe MAX(pure version) PCIlock and AGPlock???

    I have a question.
    I want to buy this motherboard and I don´t know if this motherboard have PCIlock and AGPlock for a little overclocking.
    thanks for all.

     I'm sure. It's in the bios under "frequency/voltage control".
     You have the choice of AUTO (unlocked), and several locked frequencies. Currently have mine set at 66.67/33.3.

  • _IDE problems_ with MSI 845PE Max + Win2k

    Hi!
    I hope somebody have an idea, because I'm out of tip.
    I've been using XP, and I had no problem with IDE drivers. But now I decided to install Win2k instead of XP. I installed it, configured everything (VGA + Tuner + Audio ...), and everything looked fine.
    But I noticed I have some problem with the Win2k's default IDE drivers, because if I listen to an MP3 and meanwhile I start to copy a big file from CD to HDD, the mp3 playing flickers audibly!!! :( So the mp3 slows down, and sometimes it pauses. And this is not the only symptom of the problem: my HDD is a bit slower than it was under XP (booting is too slow). However it's a quite fast HDD (WD 800BB). And another problem: during CD-writing the writing buffer always decreases to 10-20%, and then increases back to 95%, and again back to 10-20%. So it oscialltes. But under XP it was constantly 95%...
    And then I remembered when I installed Intel Applicatin Accelerator under XP, the booting became much faster, and maybe it got faster after booting too.
    So I installed IAA 2.2.2 which comes with the mainboard's CD. After install it asks for restart. I click Ok, it starts, and says need another restart, because Win finished installing new drivers. It's ok, restart. Now booting is much faster, everything looks ok, but before I could log in I got a sudden blue death because of "ntoskrnl.exe", and it complained about some memory problem. And next time Win didn't started. Hanged up at booting. :(
    Ok, next install of Win2k. And everything is the same: Win2k is ok until I install IAA (I tried it with version 2.3 too, but the same...). So it always does blue death, and sais about memory things. (But memory must be ok, because I had XP before and I had no problem with memory, and I tested it with memtest86 too).
    Please, if somebody have the same issue, or knows about any sollution, please tell me a tip what to do! Some kind of another IDE driver for me, or should I configure something else???
    I hope somebody helps!
    Thx,
    Dexx

    [
    Don't install the IAA, install the intel inf and in the IDE controller's properties enable "DMA if available".
    Man! THX! I cannot believe I didn't noticed it wasn't set automatically to DMA if available... But why doesn't windows automatically sets it to DMA ? Argh...
    And the IAA? Why doesn't it work on Win2k if it worked on XP correctly? I don't understand.
    By the way now the only thing that is missing: my fast booting
    But I don't care, now everything looks fine afterall...
    Thx,
    Dexx

  • 845PE MAX and MSI TI 4800SE Problem! Please Help!

    I'm tring to upgrade to a TI 4800SE on the MSI 845PE MAX Motherboard. But windows XP won't boot. I can't get in the BIOS setup. Just the MSI logo at startup, and it retarts every 8 seconds. Please help! Tried uninstalled ATI driver first.
    System:
    P4 2.4Ghz
    MSI 846PE MAX
    ATI All-IN-Radeon
    Windows XP

    Is that video card 4x or 8x AGP.  Not sure but I think that mobo only supports 4x agp.

  • Problems installing windows2k pro on a 845PE max

    hi..
    i've recently bought 2 sets of msi 845pe max motherboards and started installing one of them. it was okie... then i started installing the other one but i can't seem to complete copying the files from the cd to the comp and will prompt me telling me that a file cannot be copied over. so windows cannot start up. i swopped components and it didn't work. so finally i tried swopping IDE cables and it worked perfectly..... so i've got a few spare IDE cables and used them and now my working system cannot work! is there a benchmark for IDE cables or wat seems to be the problem?
    HELP!!!!!!!!!!!!!!1

    Scurran08 wrote:
    Thanks bob,
    I have read elsewhere on the Internet that windows 8 is supported on bootcamp and that it works.
    Sometimes yes, often no, but it is unsupported officially so you'll have to live with it.

  • Big Problems w/ 845PE Max-L

    Installed today,
    P4 2.2
    M/B MSI 845PE Max-L
    G/F ti4600
    512. samsung PC2700
    Upon startup,
    I get power it seems to everything but, I have a blank screen and i hear 1 beep followed by 8 beeps. It wont go into bios or anything. Any help would be appreciated.
    Thanks,
    Ed

    Ok...
    Unplug all the IDE cables and re-attach JUST the HD cable from the MB to the HD making sure the connectors are on securely and are lined up with the connectors at the back of the hard drive fully.
    If that boots to bios screen ok then shutdown again and re-attach JUST the floppy connector (again making sure it securely fitted to both MB and to the back of the floppy) then boot back to the bios screen again to check that its ok with the 2nd cable fitted, then shut down and re-attach the CD-ROM cable... again making 100% sure that all the IDE cables are attached correctly and securely both to the MB and to all components.
    Bootup again to BIOS and see if everything is as it should be... (HD, floppy and CDROM all detected properly now?)
    Now in the BIOS use auto-detect wherever needed to detect the size of the HD etc (im unfamiliar with your BIOS so the auto detect may not be required but try it anyway) save and exit the BIOS.
    Spend a little time attaching the cables to make sure they are ALL attached perfectly... it is very easy to miss align them if you are keen to get the PC up and running.

  • Sensors 845PE Max-L

    hi!
    i have a MSI 845PE Max-L.
    What does the Sys-Temp (Winbond 1) stand for??? Case or NorthBridge?
    And Winbond 3 has always ~60°(Celsius). What does this Sensor measure?
    The Winbond2-Diode measures the CPU-Temp right?
    tia
    geforceraid

    I don't try the high density memory myself, so please refer the memory test report here which is supported by MSI website.

  • G3Ti200 Pro-TD compatibility with 845PE Max 2

    I have a MSI G3Ti200 Pro-TD MS-8851 geforce 3 graphics card and a MSI 845PE Max 2 MS 6704 Mainboard. There is a sticker over the AGP port on the board which says I can only use AGP 1.5v 4x cards in the slot and If I dont I can seriously damage the mainboard. Will my card be compatible with the board?. Thanks

    it will be fine
    any modern gf cards fine,older tnt2 can be gpx4 but not all are

  • 845pe max - no signal on monitor

    Hello. I have problem with booting my pc. There's no any picture on the monitor, though the button lights green without flashing. The signal's are like this: 1, then after pause of about minute 2 beeps, and then 1. The d-bracket stays at position "Initializing floppy drive controller". The floppy isn't connected (though if to connect all the same). Clearing cmos didn't help.
    Thanks in advance for any help.

    Well, yes, it worked everything allright before.
    I've changed the video for a new one, tried different ram in different slots, changed the battery, cleared cmos with jumper...checked the cables... The monitor is working on another computer.
    configuration:
    # intel pentium4
    # msi 845pe max
    # kyngston/ddr/333mhz, 512mbx2
    # zotac/nvidia geforce 6200/agp/256bm
    # seagate 320gb ide
    # windows xp
    # power man Power Output:430W 18A @12V Output

  • 845PE Max won't detect X800 AIW

    I'm having an issue with my old 845PE Max mobo. I've had the Radeon X800 All-In-Wonder work before on this mobo, but after a recent format the card just won't budge! The mobo detected the card as a plug & play gfx card and everything went smooth, but after the recent format things didn't go as smooth.
    When I boot the computer with the Rad now, XP doesn't detect it as a plug & play card and the annoying vgasave is initiated. I've read and tried several fixes. Installed the newest INF update with the MSI Update Tool (which didn't do the trick), tried the INF update from Intel and finally booting XP by hitting F8 and running VGA Mode, none of which worked.
    What I don't get is why the card worked fine before the format, but not after?!
    Probably time for me to get out from under my rock and get a new rig, but I'm not willing to give up on this one quite yet. Any ideas would be greatly appreciated.
    Regards,
    Fischer
    PS: Before you ask, I've got SP2, Framework 2.0 and the whole nine yards in XP updates.

    Thanks for the input. I'll try, but if it doesn't work I'll just plug in a dated Nvidia card and pass the rig on. I'm crawling out under the rock and getting a new mobo+chip+ram+pci express gfx, and design a new rig. :D
    To reflect on this mobo: I've had this mobo since it came out, quite a few years ago, together with some cheap 512 sticks and a Intel P4 2.4 Ghz which I've been able to squeeze 3.1 Ghz out of with a later dual rad watercooling solution, and it's been running like this for years without a glitch. So, I think it's safe to say that I got more then my moneys worth. Salute!
    Thanks for the help, both of you.
    Regards,
    Fischer

Maybe you are looking for