MSI 845PE Max Lan - MS-6580 Ver.2.0 boot failure

I recently purchased this mainboard and components. All's working fine except for 1 strange issue:
On each 1st boot-up (after I powered down) the harddisk (UDMA 100, 80GB Western Digital) is not detected. This results in a boot failure.
After this 1st failure I reset and from then on booting is OK, harrdisk is succesfully detected (although it always takes about 10-15 seconds before detecting).
Anyone else experiencing the same problems?
This is my config:
- MSI 845PE Max Lan
- 2,4GHz P4
- Western Digital 80GB 7200rpm (set as master, only device on its cable)
- ATI Radeon 9700
- 512 MB DDR (pc2700)
Hope anyone can help out.

Note: FSB533 CPU is required in order to choose DDR333 selection in the BIOS setup
thats what is says here
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=364&MODEL=MS-6580

Similar Messages

Does MSI 845PE Max supports LBA

In fact all is in the title... Does MSI 845PE MAX (6580) supports for LBA drive?

Yes, as you need to have the patch incorporated in order to recognize the total drive to start with. There is some info here: http://support.microsoft.com/default.aspx?scid=kb;en-us;305098

MSI 845PE MAX

i'm using the mainboard MSI 845PE MAX
does anyone else uses this board?
i just wanna know if this board can support AGP 8x graphic cards
can anyone tell me?

hello, nope its support maximum AGP 4x. but good news is that you can use any AGP 8x VGA on it without almost any limitation. differents is quite little. only few visual increament. nothink performance related.

MSI 845PE Max Motherboard TV CARD problems

hello,
i'm use to MSI 845PE Max motherboard and avermedia tv card. i'm plug in to avermedia anywhere pci slot in motherboard but not installed avermedia. error is "ACPI bios system motherboard extension" How i can install to avermedia tv card.. HELP ME..!
PoWeRGuArD

i'm plug in to avermedia anywhere pci slot in motherboard
dont understand this bit,try different pci slots

MSI 845PE MAX-L mobo no power whatsoever

Hi,
Just upgraded my mobo, RAM & processor to the following:
MSI 845PE MAX-L mainboard
Intel Pentium 4 2.4 GHz
DDR-DIMM PC2700 512MB
Put everything together and worked a treat from Monday. Reinstalled all my software including XP and had everting running smoothly for over 24 hours with the tower boxed up (so no possibility of accidentally touching any componentry).
This morning I tried to switch on the machine and NOTHING. No response from the mobo no fans no lights no beep - nothing.
Checked all leads in place.
Then tried power supply (Eagle ATX 350W Switching Power Supply Pentium 4 compatible) on my old ABIT mobo together with my old 256 Mb SRAM & Hercules 3D Prophet 32MB graphics card. It worked!
So put same setup back on the new MSI mobo, i.e. just graphics card, 512Mb DRAM, power supply & Intel 2.4 processor. Still nothing. Pretty sure got all my leads from the tower in all the right places on Mobo as they matched the previous configuration and that wouldn't have worked before, right?
Whats going on, why does my pc work one day and then can't be arsed the next?
Lloydich

I had an Eagle 350watt PSU come supplied in my new case but i didnt trust the PSU so i took it out without even trying it.
What is your complete system build setup?
Those el-cheapo PSU's are not really upto running the most intense of systems despite what the manufacturers say.
Unplug a few components from off the PSU and try to boot up again... its not impossible the PSU is dead... honestly if you spend alot of money on a new system it seems criminal not to get a decent PSU, im not criticisng here im just surprised how many people dont consider getting a 'good' PSU to power their new state of the art PC's.
Try the unplugging of a few components that connect to the PSU if this dont work for you then if possible try a better PSU (350 watt does not neccesarily mean its good, some cheap 350 watt PSU's are less powerful than a good 300 watt PSU)

MSI 845PE Max-L

Is there a compability problem between Radeon 9200 Atlantis,P4 2.66 Gig prosessor and MSI 845PE Max-L ??
Memory module is DDR 400 512 Ram,HD is Maxtor 120 Gig ATA 100
Every single component works fine with my other Motherboard ( MSI 845E Max )
but when I try to start these in 845PE Max-L only thing that happens is prosessor cooler spins 2 seconds...then totally silence....I got a motherboard replaced once
already....
I cleared CMOS
tried another graphic card ( Geforce3 Ti 500 )
Nothing happens even with default settings...
Highly unlikely that two broken motherboards has been given to me !?!?!?!
Please someone tell me what to do..
E-Mail,MSN or here at the Boards...
- THX -

"Lower you DRAM Freq to 333MHz and increase you DDR Voltage to 2.7v, thereafter incrasing your AGP Voltge to 1.6v."
Why ? and how ?
cannot go to BIOS..
and I just asked if there is a compability problem...
Danny : no other cooler movement :(
just prosessorcooler spins few times,
there are no shorts between board and case through the standoffs.
I took motherboard out of case ( in case of that )
Whole F****n thing is starting to me off...
Never had this much problems with MSI-boards :(
So,once again ; every component works in 845E max ,same case,same powersupply etc.
Only sure thing seems to be : 2 broken motherboards ! ( god damn )

MSI MPower Max Command Center Error ver. 1.0.0.59

Hi everyone! I apologise in advance for my poor English.
I was very pleased with my new PC (and also with the motherboard!) until command center made me upgrade to ver. 1.0.0.59. Every time I open it I get this error message and sometimes (1 on 4 sessions) it significantly lowers CPU's clock.
The part in Italian says: " It's impossible to find part of the directory ...... \LU5_LMU.xml"
How would you fix it? Should I reinstall the previous version and, in that case, where can I download it from?
Thanks for your help,
Gilberto

here http://www.msi.com/product/mb/Z87_MPOWER_MAX.html#download
and click on utility

Have the MSI-845Pe MAX(pure version) PCIlock and AGPlock???

I have a question.
I want to buy this motherboard and I don´t know if this motherboard have PCIlock and AGPlock for a little overclocking.
thanks for all.

I'm sure. It's in the bios under "frequency/voltage control".
You have the choice of AUTO (unlocked), and several locked frequencies. Currently have mine set at 66.67/33.3.

_IDE problems_ with MSI 845PE Max + Win2k

Hi!
I hope somebody have an idea, because I'm out of tip.
I've been using XP, and I had no problem with IDE drivers. But now I decided to install Win2k instead of XP. I installed it, configured everything (VGA + Tuner + Audio ...), and everything looked fine.
But I noticed I have some problem with the Win2k's default IDE drivers, because if I listen to an MP3 and meanwhile I start to copy a big file from CD to HDD, the mp3 playing flickers audibly!!! :( So the mp3 slows down, and sometimes it pauses. And this is not the only symptom of the problem: my HDD is a bit slower than it was under XP (booting is too slow). However it's a quite fast HDD (WD 800BB). And another problem: during CD-writing the writing buffer always decreases to 10-20%, and then increases back to 95%, and again back to 10-20%. So it oscialltes. But under XP it was constantly 95%...
And then I remembered when I installed Intel Applicatin Accelerator under XP, the booting became much faster, and maybe it got faster after booting too.
So I installed IAA 2.2.2 which comes with the mainboard's CD. After install it asks for restart. I click Ok, it starts, and says need another restart, because Win finished installing new drivers. It's ok, restart. Now booting is much faster, everything looks ok, but before I could log in I got a sudden blue death because of "ntoskrnl.exe", and it complained about some memory problem. And next time Win didn't started. Hanged up at booting. :(
Ok, next install of Win2k. And everything is the same: Win2k is ok until I install IAA (I tried it with version 2.3 too, but the same...). So it always does blue death, and sais about memory things. (But memory must be ok, because I had XP before and I had no problem with memory, and I tested it with memtest86 too).
Please, if somebody have the same issue, or knows about any sollution, please tell me a tip what to do! Some kind of another IDE driver for me, or should I configure something else???
I hope somebody helps!
Thx,
Dexx

[
Don't install the IAA, install the intel inf and in the IDE controller's properties enable "DMA if available".
Man! THX! I cannot believe I didn't noticed it wasn't set automatically to DMA if available... But why doesn't windows automatically sets it to DMA ? Argh...
And the IAA? Why doesn't it work on Win2k if it worked on XP correctly? I don't understand.
By the way now the only thing that is missing: my fast booting
But I don't care, now everything looks fine afterall...
Thx,
Dexx

MSI 845PE Max2 (MS-6580 v2.0) Help Please!

OK... I'm confused ?(
Well... I got the MSI 845PE Max2 - L (MS-6580 v2.0) on
order. Now I'm reading that alot of peeps having so
many problems with it! 8o
I just read a reply from Assaf saying that the board was SUED?
First off, what does this mean?
Should I return this board when it arrives or keep it?
Also, Im a little unclear of the difference between the
845PE Max2 (MS-6704) & the 845PE Max2 (MS-6580 v2.0)
Why are there 2 Different models that both say 845PE Max2?
NOTE:
I plan on using my Crucial DDR 333 (2 x 256MB) & a PIV 2.40 (533MHz FSB).
My other Specs are below.....
Any help will be appreciated.
I rather not even open the box if this board has MAJOR problems.[/color]

Uhmm i think you are mixing boards
There is no such board (at least not yet) as a 845pe-max2 version 2.0 there is a 845pe-max version 2. There is some difference between the max and the max2 board. The max version only has room for two dimms, no bluetooth/raid and gigabit support. So you are talking about two completely different boards but with very similar names I'm not a motherboard expert but i have tried the max2 version (6704) and i wasn't completely satisfied, cpu temp is way off, bios upgrade caused wierd problems, when using my adaptec 2940uw controller raid bios disappers. I think this is a result of the companies releasing their products to soon, as far as i can tell (and i have been reading a bit ) all 845pe based motherboards have their problems. When you ask what to buy everyone is saying asus p4pe, i for one think that asus is overpriced and i really don't wanna waste money on a serial ata solution which has no future. Their onboard audio isn't suported by freebsd. I have not decided quite yet, i was actually rather satisfied with my msi 845pe max2, it has a lot of nice features and i like msi liveupdate, the board runs perfectly with other os's than windows, but i will see some response from msi regarding those problems there is,
and currently i'm awating to see if msi will release a bios that perhaps will fix those problems i (and alot others) had with this board.
Regards
Maynard

845PE MAX and MSI TI 4800SE Problem! Please Help!

I'm tring to upgrade to a TI 4800SE on the MSI 845PE MAX Motherboard. But windows XP won't boot. I can't get in the BIOS setup. Just the MSI logo at startup, and it retarts every 8 seconds. Please help! Tried uninstalled ATI driver first.
System:
P4 2.4Ghz
MSI 846PE MAX
ATI All-IN-Radeon
Windows XP

Is that video card 4x or 8x AGP. Not sure but I think that mobo only supports 4x agp.

Problems installing windows2k pro on a 845PE max

hi..
i've recently bought 2 sets of msi 845pe max motherboards and started installing one of them. it was okie... then i started installing the other one but i can't seem to complete copying the files from the cd to the comp and will prompt me telling me that a file cannot be copied over. so windows cannot start up. i swopped components and it didn't work. so finally i tried swopping IDE cables and it worked perfectly..... so i've got a few spare IDE cables and used them and now my working system cannot work! is there a benchmark for IDE cables or wat seems to be the problem?
HELP!!!!!!!!!!!!!!1

Scurran08 wrote:
Thanks bob,
I have read elsewhere on the Internet that windows 8 is supported on bootcamp and that it works.
Sometimes yes, often no, but it is unsupported officially so you'll have to live with it.

Big Problems w/ 845PE Max-L

Installed today,
P4 2.2
M/B MSI 845PE Max-L
G/F ti4600
512. samsung PC2700
Upon startup,
I get power it seems to everything but, I have a blank screen and i hear 1 beep followed by 8 beeps. It wont go into bios or anything. Any help would be appreciated.
Thanks,
Ed

Ok...
Unplug all the IDE cables and re-attach JUST the HD cable from the MB to the HD making sure the connectors are on securely and are lined up with the connectors at the back of the hard drive fully.
If that boots to bios screen ok then shutdown again and re-attach JUST the floppy connector (again making sure it securely fitted to both MB and to the back of the floppy) then boot back to the bios screen again to check that its ok with the 2nd cable fitted, then shut down and re-attach the CD-ROM cable... again making 100% sure that all the IDE cables are attached correctly and securely both to the MB and to all components.
Bootup again to BIOS and see if everything is as it should be... (HD, floppy and CDROM all detected properly now?)
Now in the BIOS use auto-detect wherever needed to detect the size of the HD etc (im unfamiliar with your BIOS so the auto detect may not be required but try it anyway) save and exit the BIOS.
Spend a little time attaching the cables to make sure they are ALL attached perfectly... it is very easy to miss align them if you are keen to get the PC up and running.

Sensors 845PE Max-L

hi!
i have a MSI 845PE Max-L.
What does the Sys-Temp (Winbond 1) stand for??? Case or NorthBridge?
And Winbond 3 has always ~60°(Celsius). What does this Sensor measure?
The Winbond2-Diode measures the CPU-Temp right?
tia
geforceraid

I don't try the high density memory myself, so please refer the memory test report here which is supported by MSI website.

G3Ti200 Pro-TD compatibility with 845PE Max 2

I have a MSI G3Ti200 Pro-TD MS-8851 geforce 3 graphics card and a MSI 845PE Max 2 MS 6704 Mainboard. There is a sticker over the AGP port on the board which says I can only use AGP 1.5v 4x cards in the slot and If I dont I can seriously damage the mainboard. Will my card be compatible with the board?. Thanks

it will be fine
any modern gf cards fine,older tnt2 can be gpx4 but not all are

MSI 845PE Max Lan - MS-6580 Ver.2.0 boot failure

Similar Messages

Maybe you are looking for