MSI 848P Neo-V (MSI MS-6788)

Hi,
Sorry for bringing a question about kind of prehistoric motherboard, but it still do the job for me (for now).
I have upgraded my hard disk to a 500Gb Samsung (SAMSUNG HD501LJ), which SATA II. I knew very well that my motherboard does not support SATA II and only SATA I.
However, as I wanted to check the HDD, I noticed using HWINFO32 that the HDD details about transfer mode are as follow:
Ultra-DMA Mode: Total: 7 (SATA), Active: 5 (ATA-100)
So of I understand well, although capable of running in SATA I, the disk is still running in ultra-DMA 5 (=ATA 100), correct?
I have tried various BIOS setting according to the manual:
Native Mode:
ATA Configuration: PATA+SATA
S-ATA Keep Enabled: Yes
P-ATA Keep Enabled: Yes
PATA Channel Selection: Both
P0-1st/P1-2nd or P0-3rd/P1-4th (does not change anything)
I have also tried:
Native mode
SATA Only
P-ATA Keep Enabled: Yes
PATA Channel Selection: Both
Combined Mode Operation: SATA First.
S-ATA Ports Definition: P0-1st/P1-2nd
Results are still the same.
So few questions:
1/ Am I missing something?
2/ Do I need to set jumpers on the MB or on the disk?
3/ Do I need to install specific Intel SATA driver (either during Windows install or after)?
4/ Is the BIOS configuration correct?
Thank you in advance for your help.
Cheers,
Rv
PS: I am running Windows XP SP2.

Performance of S-ATA l and Ultra-DMA 100 P-ATA are just about the same so I wouldn't waste any time worrying about it. I compared 2 HDD's I have a few years ago, Maxtor 60 GB Ultra DMA 100 P-ATA and Maxtor 80 GB S-ATA l and performance was exactly the same for both of them.

Similar Messages

MSI 848P Neo Series MS-6788 Model

Hi,
I'm new to building PCs and I have just built a P4 2.8GHz 800FSB Machine with an 848P Neo Series motherboard.
I have a few issues:
I cannot use a PS2 mouse it simply will not work.
With my PS2 keyboard, turning on num lock or caps lock causes the PC to lock up.
Is there some sort setting in the BIOS I need to change or is the board faulty?
Another issue I had which has now magically fixed itself - when I turned the pc on, I had to turn num lock on and then off to get the monitor to come off standby and to get the pc to start booting - any ideas?
Could you please help with with these problems as I don't have long to return the motherboard if it is faulty.
Thanks in advance

Hi Maggioni,
Look on side on PSU.....somewhere the will be the different "Rails".... list 12V,3.3V,5V, in AMPS. IE- 12V+ = 20A etc.
Hmmm, as for Keyboard.....is it a standard 105 or 102? Maybe, it is an enhanced with extra keys? Wireless or Corded. (If wireless....try changing the batteries)
Also try changing keyboard....borrow or buy a budget one.
Del

MSI 848P neo-V

my love:
MSI 848P NEO-V
CPU celeron 2,4Gh bus 533
Ram 512Mb
HDD seagate sata 80Gb
AGP Asus V9400 X
today, i make a ghost file with nortonghost ver 7.0, there's strange. Ghost speed just about 100Mb/Min ( same specification with ASROCK is 400Mb/min) . I don't know why, i think it maybe come from Cmos setting. Mod and ACE please help me.thanks in advance

thank you, i've just enable it, i will check later, there is another problem, i just bough a CDRW, i install into my computer, but my computer doesn't analize, it looks like nothing install,my computer only analize my old CD, if i take out my old CD then my computer "see" my new CDRW and i use normally. Please help me, i need to use both CDs.thanks
note: i set master for my old CD and slave for new CDRW.
one more thing, onchip controller ATA(s) have two selections, one is lagacy mode,one is native mode, please explain what different between them??

MSI 848P-Neo - Mobo don't start at all

Hi,
I have a MSI 848P-Neo mobo with a P4 Ht 3.0 Ghz on it. New PSU 360W Enermax (12V 26A, 5V 32A, 3.3V 32A). No HDD or CD Drive are plugged. No card in PCI slot, except VGA in AGP Slot. 1 RAM stick in slot.
When I power on the system, the D-Bracket with Diag led light as follow:
1 and 3 are red
2 and 4 are green
I check in manual for signification but this case isn't in the manual.
I don't hear beep from speaker.
Can you confirm me that is the mobo the problem ?

Have you Clear CMOS Guide yet with power cord removed from the PSU 1st?

CL3 Memory wont work on Intel 848P Neo Mainboard? any help?

Hi,
I purchased Kingston DDR Ram recently and put it into my computer. It worked fine but sometimes I start computer up and it comes up with a message saying something is wrong with the memory timings. I dont think it is configured properly.
In the BIOS there was an option to "CONFIGURE DRAM TIMING BY SPD" and i set that on ENABLED. If i set it to DISABLED then there are other options that I have to set.
These options are as follows:
1. CAS# Latency [Options 2 or 2.5 Clocks];
2. RAS# Precharge [Options 2, 3 or 4 Clocks];
3. RAS# to CAS# Delay [Options 2, 3 or 4 Clocks];
4. Precharge Delay [Options 5, 6, 7 or 8 Clocks];
5. Burst Length [Options 4 or 8 Clocks].
These are the 5 settings i can modify and in the "[]" brackets are the options i can select from for each one. Could you please tell me how I am to configure this in order for the memory to work. The Ram voltage is set at 2.6v. The CAS# Latency only allows 2 or 2.5 clocks so im not sure if thats the problem or not.
The specifications of my computer as as follows:
RAM - Kingston KVR400X64C3A/1G 1GB PC3200 CL3 184
Motherboard - MSI 848P Neo (MS-6788 v1.0)
Motherboard BIOS - A67991MS v1.0081203
Motherboard firmware - V1.0 initial release
CPU - Pentium 4 2.53Ghz
Regardless of the settings I have done so far, if it works past POST and loads windows...after sometime it randomly resets. Any idea why this is the case? I suspect its the CAS Latency. The manual says you can select 3 Clocks but i dont see that option, just 2 or 2.5

The Kingston Site is not always correct or to be more precise: it does not state the operating conditions under which DDR-400 is possible on this mainboard. In this cases the problem is not the modules as such (they are able to run @DDR-400) if they are put into a system that supports that.
In your case the problem is the mainboard's chipset which can only make the memory run @DDR-400 when an FSB-200-MHz processor is installed. You are currently using an FSB-133-MHz processor. With such a processor, the maximum memory clock speed that the system can run at is DDR-333. I just checked the Intel Datasheet for the 848P Chipset. That is also the reason why all DDR-400 modules mentioned in the official MSI Memory Test List for this mainboard were tested with an FSB-200-MHz-CPU installed.
The only thing you can do to get aroung this "problem" is to install a supported FSB-200-MHz-processor.
Quote
Also, when i look at my motherboard manual, it shows option for 3 as CAS latency but in reality when i check the bios its not there (which im assumin is reason y it wont work).
It would probably be there once a processor is installed that will enable higher memory clock speeds than DDR-333. However, the actual CAS latency is only of secondary importance here. The main question is why DDR-400 is not possible (which would automatically yield a CAS Latency of 3 by settings the values in the corresponding SPD Profile). And as I said: DDR-400 is only possible with an FSB-200-MHz-Processor.
With your current configuration, the highest possible memory speed is DDR-333 @2.5-3-3-7. In case that runs fine & stable everything is working as it should.

848P Neo-LS Fan Control

As said - no control of the damn fans (Case/CPU) on my 848P Neo-LS. On the CoreCenter the button lits up on mouseover, but when pressed, nothin' happens (as said in manual, press to toggle user/auto modes for fan control).
Also CoreCenter doesn't show the Case fan's speed, but Northbridge (NB fan) fan's speed, which is obviously 0. Also NB temp is N/A. Also +12V is N/A. Also the FSB stays always at 101 Mhz, not 100. No overclocking done.
Today upgraded the CoreCenter to the most recent vers (1.7.0.0.), and the button doesn't lit up anymore...?
When I installed SpeedFan 4.17, it allows me to control the Case fan's speed from 2300 - 2700, but nothing more. Interesting.
CPU - Celeron 2.0
RAM - 256 MB Kingston
CPU Fan - OEM intel fan A80856-003
Case Fan - MJ 802512
Both fans with speed sensors, of course.
Should I update the bios?
Help somebody!

To be sure I opened the case and stopped the fans by hand (I don't use the corecenter prg - piece of crap), to see that i have mistaken both fans (in SpeedFan prg). The one who varies by 400 rpm is the Cpu fan.
Doooh.
The bios health screen doesn't show +12V at all - just aint there...
The MSI tech support sez - flash the bios, and if anything doesnt change, the CoreCell chip has gone (faulty, whatever).
Flashed the bios (1.0 - 1.9 now). No changes.

Does the 848P Neo-LS support celeron D 315???

Does It???, in the msi page says that celeron D wont work on 848P Neo-LS motherboard, but other motherboards with this chipset works fine with celeron D, someone knows if it works or not?

Well my mobo (KT6V-LSR) doesn't even list the 2600+ barton, but I haven't had any issues, but where the CPU support actually lists it as NO, that usually means they have done testing. So I would say most likely no, but depending on where you buy it from you may get a chance to try it.
Good Luck
Jeremy

848P Neo-LS RAM-memory ?

Hi someone who ones where i can find witch ram memory i should have for my 848P neo-LS ??
I have Kingston 512 Pc3200 CL3 is that ok ?
thanks
Henke L

http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_detail.php?UID=493
The Memory Modules link on that page will give you the modules the board has been tested with. Others may work as well, but just haven't been tested.
I didn't check to see if the Kingston are in the tests, but they do work with other boards using the ICH5 chipset.

848P NEO-LS SATA (Native Mode) - Cant Install WinXP

Okay guys -
I have a 848P Neo-LS which seems to be somewhat rare on this site in the support sections.
Its a brand new board and looks very fancy. I have a lot of experience with PC's as I repair them on a daily basis however this is my first adventure into the land of SATA.
To go with my lovely new MSI motherboard I have purchased a 120GB SATA Hard Disk.
In the BIOS for the motherboard under "Intergrated Peripherals -> On-Chip IDE Configuration" I can choose to operate the On-Chip ATA in either legacy or native mode. According to the manual that came with the board for Windows XP, I should use Native mode (which is exactly what I want as it allows for 6 ATA devices, as opposed to only 4 with legacy mode - im using a mix of SATA and P-ATA devices).
When set to Native mode and booting the Windows XP Pro installation CD, it gets so far then I get a blue-screen warning me about a possible harddisk problem?
But if I set it back to legacy mode and boot the Windows XP Pro installation CD, everything goes through okay and I can choose to begin installing XP if I wish.
However I want to run in Native mode as this will allow me the mix of SATA and P-ATA Harddisks that I want to run. The manual provided with the MSI board also instructs me that this should be possible.
Its not working - what is wrong???? From my knowledge of NT based operating systems im guessing I need to press F6 during the installation CD boot sequence and insert a driver disk for the SATA controller? Although it seems strange that this works in legacy mode - perhaps I have answered my own question here and that isnt the problem?
Or maybe I need a BIOS update, or maybe something entirely different????
Can someone please answer my question as I would love to get using this wonderful new PC.
Thanks in advance for any advice.
Delirum Sky

You don't need to install any SATA drivers for your board. I suspect a compatibility issue with the HDD or on of the other SATA/IDE devices you have connected. I would do the following:
Search the Maxtor site for common issues with your model#
Install XP in legacy mode and then switch to native mode as suggested above. I have switched back and forth between modes with no trouble.
If you still get problems,
1. Update to latest BIOS if one is available. Most new Bios'es on the newer boards include fixes to compatibility issues with SATA devices and memory.
2. Try installing XP with only the HDD and a generic CDROM or CDRW attached. If this works, install the other devices back one at a time and test to rule them out as the culprit.
With a recent Bios and your setup I would set On-Chip Config:
Native mode
SATA Only
Keep PATA active-Yes
Both channels
Leave rest at default.
Hope you get it working.

[848p Neo S]please Help Me

Hi
Please Help Me
My Pc is Very Slowly
*** any person enterd her replay me please***
EXAMPLE:-
TRANSFEAR 4 GB FILMS IN 10 MINUTES
Component
MOTHER BOARD MSI 848P NEO S
PROCESSOR INTEL P4 2.6 CASH 512 PATH 800
RAM 256 DDR PATH 333
VGA 128 ATI RADEON 9200 SE
H.D 80 GB WESTREN DIGITAL 7200 RBM
SOUND CARD 128 DIGITAL CREATIVE
FAX INTEL
PLEASE HELP ME
WHAT CAN I DO ?
THANKS

Hi,
I would say 4.9Mb/s on such a large file is good....
1GB = 1024Mb
1Gb = 2.5 mins to transfer
Therefore 4.9Mb are transferred every second...... If you are looking for the 100MB/s that's PEAK and not actual......
Del

Problem with 848p NEO V and GeForce FX 5600 point of View

Hello there,
I have bought a mobo yesterday (848p NEO V) then when I tried to plug the graphic card (Ge Force FX 5600 point of view) the computer reboots just before entering Win XP PRO.
So I tried another graphic card (ATI 9200), all worked fine.
In the same way, I tried my GeForce in another mobo (ECS P4VXAS) and of course all worked fine.
Each time I tried the MSI mobo with the GeForce card (using diffrents drivers), it doesn't work.
Does someone know where could this problem come from?
Thank you very much
PS: Sorry for my ugly english.

MOBO: MSI 848p NEO V
CPU: Intel P4 2.4 A
Ram: 512 M DDRSDRAM PC3200 (noname) two 256 modules
DD: 40Go (MAXTOR), 40Go (MAXTOR)
Display: Point Of View GeForce FX 5600 128mb
Sound: Sound Blaster Live! 5.1
Controler Card: Sillicon Image 0680A ULTRA ATA 133
DVDROM: LG
CDROM: Samsung
DVDRW: Liteon
OS: Win XP Pro SP2 FR (all critical updates installed)
all cddrive on motherboard IDE controler
hard drives on controler card
PSU: 350w noname
Tell me if you need anything else.
Thanks

848p Neo

Can any one help me I have just bought MSI 848p Neo motherboard and keep getting
Pci fast ethernet controller v2.11 (001205)
PXE-E61: Media test failure, check cable
PXE-MOF: Exiting PXE Rom
Cant get my head around the problem. Thanks Keith

Disable "boot from network" or similar in the BIOS.
Moan Guide

848P Neo-S Drivers

Hi, I've both a mother board 848p Neo-S , I've install al correctly but I've lost the drivers cd-rom, so i haven't sound !
In MSI Homepage http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=493 i have downloaded the win xp service pack (as they indiques) but the sound is not here yet.
Anyone can help me?
Thanks

Please read and provide information requested in Moan Guide

Overclocking p42.66 (c1) on 848P Neo-LS help!!!

hi i am looking to overclock my p4 it but i dont know what settings i should have in the bios.
here is my system:-
INTEL P4 2.66GHz (C1 STEPPING)
AKASA P4 BLUE LED HSF (UPTO 3.6GHZ)
MSI 848P Neo-LS
1GB SAMSUNG DDR333 PC2700 CL 2.5
ABIT SILURO GF FX5600 ULTRA OTES 128MB DDR 400/800 (FLIP CHIP)
80GB SAMSUNG HD 7200RPM
550W QTEC PSU.
i have updated the bios rev. to 1.2 (latest).
also i have 7 80mm blue led akasa fans installed in clear case for controlled air flow.
any help in this matter would be great.
if you need any more info i would be glad to help.
cheers

read this guide:
https://forum-en.msi.com/index.php?threadid=40413&sid=

Cant boot computer with 848P neo-v mobo

Hello
I've got a pentium 4 computer with 256ram and an MSI 848P Neo-V motherboard. Yesterday I tried to start up the computer without anny problem. I notice that my mouse and keyboard don't work. I press the reset button but it doesn't work. Suddenly I got a black screen. Since the i'm unable to boot the computer. If I press the start button the fan's are working the Hard disk is spinning the processor fan is spinning.
But that's it nothing on the screen. :(
So I went looking for the problem I cleared the cmos settings put in a new battery. tried new ram, New harddisk, new Graphics card, new power supply But its still not working.
The only strange thing that i'm noticing is that the red led at the front of the case stay's on. Normaly it flashes when the cpu is working but it stay's on.
It also seems like the computer Is looking for a dvd.
Is the motherboard dead or is there a problem that I did not think of.
Thx
Btw: sorry for my bad english

Hello Realiks,
please provide full system specs including PSU details. Read the >>Posting Guide<< to get an idea of what we need to know.

848P Neo-LS [help configuring ...]

I just set up a 848P Neo-LS
support for:
800mhz FSB
400mhz DDR
I installed a P4 2.8c which should be able to run at 800mhz
I don't feel the mainboard manual give enough detail to explain how to set up the bios and when i view "CORECENTER" it shows my pc running at 200mhz FSB. and when i click where it shows this on the right pannel, what's with the 200mhz x 14.0=2807 mhz?
I just want to make sure my pc is running at 800mhz FSB and my 400mhz pc3200 ram i have is running optimally as well.
ALSO, in the bios it shows the DRAM, PSB 400MHZ, PSB533 MHZ AND PSB800MHZ.
IF PSB is stands for another bus what bus is it and y do the equivalants to 400, 533 and 800 only = 100-344mhz, 133-500mhz and 200-500mhz respectively?
ANY help would be appreciated, i know from viewing this forum that there are MANY of u out there that are EXPERTS with MSI boards and setting them up.
thanks for any help
IRISHHUNK
(St.PAtricks day's commin up, have fun

And PSB (Processor Speed on BUS) is Basically the same as FSB (Front side Bus) only it is a different Name, So set your PSB to 800 and you should set your Memory to 400MHZ or "Auto" if you have this Choice.You may also come across something called PBS (Processor Bus Speed) which is Actually the FSB Divided by 4 so it is PBS X 4 = FSB in your Case PBS=200 X 4 = 800MHZ FSB or PSB.....But we tend to use FSB in this Forum so as Everybody does NOT get Confused .........Sean REILLY875

MSI 848P Neo-V (MSI MS-6788)

Similar Messages

Maybe you are looking for