MSI 865PE Does not boot???

Good afternoon everyone!
I am having a problem getting system to boot. I have everything plugged in and system seems to start but no video. Fans are running, Northbridge running but nothing happens. Have unsitted everything but still no luck. Any suggestioins??
MSI 865PE NEO2-FIS2R 865PE P4 800FSB Skt478 DDR ATX
Kingston HyperX KHX3200K2/512 512MB Kit DDR400 PC3200 Memory
Intel® Pentium® 4 Processor 2.8GHz, 800MHz FSB, Socket 478
Googlegear 601AEB-420DF Mid Tower
ATI Radeon 9200 AGP 8X 128MB DDR

Fixed problem!! D Bracket came to life and found bent CPU tooth. Fixed and up and running!!

Similar Messages

MSI P6N SLI V2 does not boot up from cd/dvd and few other problems

HI
I just bought a computer P6N SLI V2 + E6750. It has following problem. It does not boot from cd.
I have Sata HD. CD/DVD is installed to IDE as a master.
I have done settings in bios so that First boot is cd/dvd and second is sata HD. Anyhow it still goes to the hd and stars windows.
I was only able to boot up from cd when I disabled hd from boot sequency. Meaning I left only cd/dvd there.
Hopefully you pro's can help me.
Then there is another problem. Windows is telling me that it found new pci device. I do not know what device. I have only Graphig card (geforce 8800 gts) installed into pci-E. Drivers and software are also installed, I assume proberly. How to find out what windows thinks it found.
Third problem is onboard soundcard. I cannot get any sound out from the machine. I have downloaded driver from realtek, but still no sound.
Unfortunatelly I do not have original software for motherboard. Only the latest from MSI website.
Hopefully someone can help me.
thanks.

About bootup, i dont know yet.
To find out what windows found, look in devicemanager.
To go there go to controlpanel, system then choose devicemanager.
There you can see what's installed.
Last, your soundcards needs to be enabled in bios, under integrated peripherals there should be a line with "onboard sound", enable this and sound should work, unless its broken.

New system does not boot properly

I just set up a new system with:
a MS-6728 Neo2 FIS2R Mobo,
1gb Geil PC-3500 RAM (2x512),
2.6C proc.
2 Maxtor 120gb IDE drives RAID 0 with the onboard promise controller.
Lite-On DVD burner
ATI radeon 9800 video card
Enermax 300 watt power supply with:
3.3v - 28amp
5v - 30amp
12v 22amp
170watt total 3.3/5 combined
My problem is that my system NEVER boots up normally. It always freezes in the bios startup. The D-bracket stops at almost every possible combination of led's, which according to the manual the problems were: Testing RTC, Initialize Video interface, Testing memory, Initializing floppy controller, Memory detection, Decompressing bios to ram, possibly more. Sometimes I also just get beeping, either a continuous beep or 8 beeps. A few times it would display the bios startup screen, but halfway down would be gibberish characters and would be locked up. When I then turn the computer off then on again, the bios is reset at least somewhat(i know because I usually disable the full screen image on startup) and says memory timings are too tight, and I have the choice to enter bios or hit any key to automatically fix things. If I hit any key it will boot up ok. However when I restart/turn off the computer, the next time it again does not boot. I tried upping the ram voltages from 2.5-2.9v, and that seems to stay that way in the bios, even when it resets itself. Everything else is set to auto/slow. If I try to manually adjust the memory timings, even to the slowest possible settings, it does not boot, and I must turn it on/off a few times till the bios resets again, with the boot process stopping at one of the possiblilitys mentioned above. Using the info tab on speedfan, I got the memory info, and it displayed the voltage at 2.5v, not sure what that means but it is strange.
What I have already attempted:
I sent back the ram and got a new set, which hasn't changed anything. The first time the other ram failed memtest, this time it passed(for about 2 hrs). So I don't think its the ram.
I borrowed an antec truepower 430w powersupply, which had no effect.
I went back to bios version 1.3 from 1.9, which also seems to have no effect.
I was hoping to overclock the system a bit and enable performance mode etc etc, but now I'll be happy to just not have to go through a song and dance everytime I restart the computer. This is only the second computer I have built from scratch, and the first with raid, but that seemed to all go ok. Please help me diagnose the problem!

I too am having problems with my system.
865PE Neo2-FIS2R
2 Maxtor 120GB S-ATA drives, RAID 0, Promise
2 512MB Geil Ultra CL2-3-3-6
HP CD-RW
What IDE settings are you using?
E.g...Native? P-ATA Only...all of those settings
For me...sometimes XP will install and boot...but eventually system is unstable and XP crashes and corrupts itself...Event Manager errors different each time
Someone mentioned problems with Maxtor and AMI BIOS...anything I should keep in mind?
Sorry about all the different questions. I'm sure exactly where my problem lies. MSI thinks it may be my memory AND/OR on-board IDE controller since I can't get the on-board Intel RAID setup to consistently "see" and setup my RAID drives...even when it has worked...XP doesn't like the Intel configured RAID drives. Also tried just one S-ATA drive through on-board Intel and Promise. Next I will try a plain old IDE Hard Drive...no S-ATA...and make sure my memory passes memtest86+ testing.
Any other gems you can offer for this config??? Thanks.

KT6V + sempron 2800 does not boot when BIOS saved

Hi,
I have just bought a new sempron 2800 to be use on a KT6V LSR. I plugget in my KT6V but was not recognised well (but all was working ok with windows). To be recognised, I have flashed with the last bios of MSI my motherboard... and now I have the following problem:
- I clear CMOS, then boot. It comes ok (processor detected and set a 1200Mhz)
- Then CMOS has a bad checksum: I enter setup, then load default, save.
- I reboot: the computer does not boot up.
If I re-clear CMOS I can re-enter setup and modify frequencies or other options. But when I save my modifications, then the computer does not reboot anymore (I have to re-clear cmos again)...
I tried to apply the configuation I found in this thread:
http://forums.amd.com/lofiversion/index.php/t69536.html
It says that SDRAM must be at 333, FSB at 166 and multiplicator at 12. When applying this settings, it does not boot (the leds indicate that the chipset initialisation (the first step) does not pass).
If I just load biios default, the leds indicates that it fails when checking the memory (second step of boot). I suspect that it's a problem of memory (but my memory was working well before !): it's 2x512 of DDR 400.
Any suggestion is appreciated :D . I spent several hours trying to configure the bios but it does not boot..
(I'll also try to find help on AMD forums...)
(Some extra info: my PSU is 26A for 12V, so it seems that it's not due to the PSU (as I read in the FAQ of this forum).
Thanks,
Ptitmain.

AMD Geode™ NX Processor Family & DB1500 Development Board
Powerful Software Development Capability for AMD Geode™ NX Processors
The AMD Geode™ NX processor family consists of three versatile and powerful products - the AMD Geode™ NX 1250@6W* processor, the AMD Geode™ NX 1500@6W processor** and the AMD Geode™ NX 1750@14W processor.***
The AMD Geode™ NX processor family leverages advanced architecture to provide powerful solutions for a variety of Internet edge, peripheral applications, and more. The AMD Geode™ NX processor family provides the highest x86 performance for fanless operations.
The NX processor family leverages Mobile AMD Athlon™ processor technology to deliver superior computing power for a variety of thin-client and other applications including point-of-sale terminals, kiosks, high-end printers and home media systems.
Key features include:
* Low-power consumption
* Advanced 7th generation core
* Long-term manufacturing and support
* 128KB level 1 cache
The AMD Geode™ NX processor family is supported by existing low-cost infrastructure, proven architecture and a long-term supply commitment.
The Geode NX 1250@6W processor is based on an AMD Athlon™ core and demonstrates the company’s commitment to making enhancements to its x86 product offerings and delivering a full line of x86 products to market. The AMD Geode family of embedded solutions is part of AMD’s strategy to offer assets, resources and vision for extending x86 solutions from low-power embedded solutions up through the highest-performing server platforms. The Geode NX 1250@6W processor is a cost-effective solution for customers requiring sub-one gigahertz performance without a fan. Operating without a fan not only reduces design costs and allows for better power management, but also allows the processor to co-exist in virtually any environment because it can operate silently.
The AMD Geode NX 1250@6W processor broadens the selection AMD’s customers have for x86 solutions that range from sub-one watt to 14 watts, allowing them to choose a processor that best meets their individual design needs.
.13um fabrication process
128/256KB L1/L2 cache
266MHz Front-Side Bus
Floating Point logic
AMD PowerNow!™ technology
Less than 6 watt maybe i should replace my PSU with battery (typical) to 9 watt (maximum) Total System Power Dissipation
Socket A compatibility
3DNow!™, MMX™ and SSE Instruction Set

[solved]kernel 2.6.27 does not boot

Today I have updated my kernel to version 2.6.27. But now my computer does not boot anymore. No error message, last line says:
pci 0000:00:00.0: Enabling HT MSI Mapping
Can anybody help me?
FSM
Last edited by FSM (2008-10-14 10:28:52)

Glad it worked !!:)
You should make it permanent by adding it to your menu.lst file. And mark this thread [Solved] please
Last edited by Onwards (2008-10-14 10:23:11)

P35 Neo does not boot

Hi,
I have just bought a P35 neo F and a Code 2 Duo E6550 processor.
When I switch the power on, the cpu fan starts and stop and then start again which looks OK for this motherboard - My problem is that the system does not boot after this - I have tried different combinations (with or without memory, with or without hard drive, with or without graphic card, I have tried 2 different graphic cards, 2 different power supply... no result - Could someone help me ?
My config :
MB P35 Neo F
Proc Intel core 2 duo E6550
Power supply Enermax extreme power 500W
Graphic card Asus EN 8600 GTS
Thanks

Quote from: gatebill on 25-January-08, 22:06:15
I've tried a Kingston PC2 6400 CL5 - the system still do not boot up - I can see the keybord blinking at the beginning of the boot process but the screen noes not receive any signal - I get a bip after about 20 sec and another one again after 20 sec.
The processor or the mother board must be faulty...but how to know which ?
MSI P35 Neo2-FIR (bios v1.5)
Intel E2180
Tuniq Tower 120
2 x 1GB Ballistix PC2-8500
XFX GeForce 8600GT
Maxtor 80GB
Seagate 250 GB
Advance 550 watt PSU
I just finished building this rig, and had exactly the same "no boot" issue using Ballistix RAM. The board powered up, then it did the auto shutdown thing which is normal, and then it started up for real, the diagnostic LEDs on the mobo light up, the CPU fan spins, I get a single beep but then just a blank screen, no POST screen, can't enter the BIOS
I tried a minimal build outside the case using just the graphics card, monitor, keyboard, and a single stick of Ballistix RAM in four different slots, re-setting the CMOS at each attempt, But still no POST
I was advised the Ballistix may be the problem as they're rated at 2.2v and the MSI board sets 1.8v until you change the voltages in BIOS, so I ordered 2 sticks Kingston Value RAM 667MHz rated at 1.8v, Inserted a single stick then powered up, but still no POST, Inserted the second stick and the board fired up! I needed both sticks inserted to boot, glad I ordered 2 sticks of Kingston instead of one, I'm keeping them as a backup if the Ballistix fail. Inserted the Ballistix and they're running fine @ 1160 MHz CAS 5: 5: 5: 15: 2T 2.3v

New MBP i5 does not boot after hard disk swap

Hi there,
I received my new i5 MBP today. After booting it once with the installed HDD to check if it's ok, I exchanged the hard disk for the one in my Late 2008 Macbook Pro. After doing this, my Late 2008 Macbook Pro boots fine with the (new) hard disk from the new i5 MBP, but the i5 MBP does not boot with my old hard disk.
To give you some details:
- I have installed 10.6.3 on the (old) hard disk that's not booting.
- The i5 MBP boots fine from the installation DVD
- Disk utility finds and can read my hard disk, no errors
- PRAM NVRAM reset did not help
- when booting in safe mode, I can see the system stop booting after or while loading Extensions.mkext
My guess is, it tries to boot and load the wrong Extensions for the new system (CPU? GPU?). I have no idea how to fix this.
Any help would be greatly appreciated!

Focx,
Welcome to Apple Discussions.
Inserting the drive from an earlier model MBP will probably not work. The version of the system you have on that HD is designed for earlier hardware so when you put in in your new machine it's going to be recognized. What I'd recommend is re-installing the disk that came with the new machine and of course putting the 2008's disk back in the old machine. Then use Migration Assistant on the new machine and migrate your data from the old machine into the new machine.
This will provide a much more stable system and should work just fine.
Regards,
Roger

Satellite L745D-S4214 Does not boot; HDD recovery partition not working

I tried to apply the recent windows 7 updates and my laptop no longer boots. I tried to press F12 and select the HDD Recovery partition, but it does not boot regardless. There is a message that it does not communicate to a specific device. I believe the address called out was 0xc0000e9, but I am going by memory. I never created a recovery CD because I thought I was covered by the HDD partitions. This was purchased on 10/26/2012, so it should still be under warranty.
PLEASE HELP!

Hi I'm going to assume that your recovery works like mine and that the recovery partition is still good and not corrupted.
Shut down your PC. Press F12 and select HDD recovery. Click enter. This should start the recovery from the hidden recovery partition.
PS I would advise you to make the recovery discs or USB recovery Try this first.
Perform a power cycle
Even when your laptop is off and unplugged, residual power can still be held in some components. While this is normal, clearing it can help with boot problems. Perform these steps to complete what’s called a power cycle.
Ensure the laptop is turned off.
Unplug the laptop's AC power cable.
Remove the battery (if the model has a removable battery).
Unplug all wires or peripherals. This includes CDs, DVDs, USB sticks, mice, printers, and any other accessories.
Hold down the power button for thirty seconds.
Reattach the battery.
Connect the AC adaptor to the power socket that was confirmed to be working in the first step.
Connect the other end of the AC adaptor to your computer.
Try starting the computer.
If your laptop starts normally now, you're done!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

Satellite M30-107 does not boot correctly after Recovery disk usage

Hi
I've recently got hold of a second hand toshiba Satellite M30-107 laptop, and decided to freshen it up.
I used the toshiba recovery disk, but after doing so the laptop no longer loads windows.
When turned on it shows the Toshiba start up disk for about a second then goes to a blank screen and freezes.
When turned off and on again a screen comes up reporting an error in shutting down and gives the options to start in safe mode etc. but choosing any of the options causes the machine to freeze.
Any help or advice would be much appreciated.
Thanks
jt

Hi
Sounds a little bit like the notebook does not boot due to the Windows software issue
Did you recover the M30 with the original Toshiba recovery CD which was supplied with this M30 unit?
Maybe Im wrong but for me it looks like a wrong recovery CD was used and an image with non compatible drivers was installed
You could try to install the OS from original Microsoft Win XP CD and could check if it would be possible to get the notebook ruining using clean OS.
In such case we ( you and me ;) ) could find out if this issue could be related to the software or hardware.
Bye

X102e - Hard drive does not boot into Windows

Hi, I was trying to reinstall Windows on my X120e.
I tried clean install with Windows 7 Professional, but the hard drive does not boot into the Windows once it has done the first phase of the install(you know, the copying part)
After the restart done by Windows, it goes as far as "Starting Windows" but does not actually boot into the Windows.
When I try to install Windows with another HDD, the device works well, but I can't swap the HDD because it is not 7.5mm think HDD.
Is there any possibility the HDD will work trough any software-level process? The HDD works fine as external HDD when tested with external HDD adapter, and installs well. only problem is that it fails to boot
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Thank you for reply.
This is not exactly the issue. I was talking about the HDD originally installed in the PC.
The PC successfully recognizes the external disk I used to install the Windows, but the problem was that I did not boot into the "First boot" screen, which basically works on the already installed data.
As of now I have installed an SSD and is working fine. strange part is that HDD works just fine when I use it as an external HDD via adapter. Strange huh?
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Toshiba Satellite P870 upgraded to Win 8.1 does not boot

I have a Toshiba Satellite P870 with Win 8 preinstalled. Soon after upgrade to Win 8.1 and basically successful removal of “watermark error” (secure boot activated) the machine stopped booting completely: after pressing the power button ventilator sound
is heard with periodically changing loudness as well as clicking sound from the speakers. The screen stays black. Attempts to start the PC through pressing F2 or zero buttons did not produce any result. Neither did I succeed with recovery discs I created before:
the system simply does not boot from the disk. It looks like I tried all options offered by Microsoft and Toshiba. I would be happy to roll back to factory settings.
Could someone give me hint what to do next?

Hi,
For the issue, let us know how to remove the “watermark error".
Meanwhile, I would like to confirm if you could access the BIOS.
I suggest you update the BIOS version to test it.
If you want to repair the startup issue, you should use windows 8.1 recovery discs or installation discs.
Meanwhile, if you cannot access the BIOS, it may be caused by hardware, I suggest you contact the Toshiba manufacturer for further help.
http://support.toshiba.com/
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact
information.
Regards,
Kelvin hsu
TechNet Community Support

Satellite A105 WIN XP does not boot or load...

Ok, so my wife's laptop has a boot issue. Model is A105-S4284
The Toshiba/Phoenix screen loads, but does not boot/load XP. It gives a black screen, then sits for a few secs and restarts. it will continue this loop indefinetely as far as I can tell. When this happened, she complained that it has been taking longer for it to boot into XP recently. (Wish she had told me before)
I can get to BIOS system utilites, Boot menu, and can access F8/Win Advanced options boot choices. I have tried the following:
Safe Mode
Safe Mode w/command prompt
Last known GCFG
Disable Auto restart on failure
I have also done a battery pull and unseated the memory, even swapping left/right, and attempted boot from just one mempry module, all with no change.
Apparently her DVD/optical drive is toast (apparently has been) so I can't do a recovery disc, but I did make a recovery USB drive. No dice there either.
What have I not done? Since I can access the adv. opt. menu it seems winXP is still there. most likely she shut it down while XP was installing something, and now there is some type of error in the registry or somewhere, but I can't seem to recall or remember what my next steps would be to gain access to I can try to clean it up and recover.
I would do a complete wipe and start from scratch, but her entire work portfolio is on the HDD and she (foolishly) has not backed it up, at least not recently. Is my best bet to get an outboard drive enclosure and set the jumpers to slave, so I can attempt to recover the data that way?
I'm a bit stubborn, and know my way around a computer, and I refuse to give up and drop it off at the geek squad.
Please help!

Satellite A105-S4284
her entire work portfolio is on the HDD
First things first. You should rescue the files.
Remove the hard drive and place it in an enclosure accessible from a desktop via USB.
-Jerry

Reset Password - System does not boot from DVD

My System: Macbook Pro - 2Ghz Intel Core Duo - OS X - 10.6.8
Hi everyone,
i forgot my password. So i want to boot from install DVD to reset the password. Unfortunately my macbook pro does not boot from DVD (10.6.3).
I press c all the time...but sometimes the macbook pro throws the DVD out...and sometimes nothing happens.
The DVD drive is working fine...
Any other idea?
Thanks in advance.
Fabian

So when you boot holding option it shows a padlock with a password field? Is that correct?
In that case we're talking about the firmware password, which you can't reset via the install disk. There is only one way to do this, I'm not certain if one is allowed to divulge that information publicly - might want to try googling "reset firmware password"

Macbook pro does not boot after upgrading ram

I have a macbook pro late 2011 which runs with mavericks operating system . I have tried to upgrade my macbook to 8Gb. Macbook does not boot when the two ram slots are filled with 4GB ram but runs well when the slots are filled with 2GB ram. When i try them individually with one slot of 2GB ram and another slot with 4GB they run perfectly which shows status ok in the RAM info. What could be the problem .

Around here, most of us recommend only Crucial and OWC for RAM because it's guaranteed to work with Macs and it's what most of us have. If I were you, I would return the RAM and look at purchasing RAM from either Crucial or OWC. If you can't get their RAM to work then you'll know that there's some trouble with your actual slots.
Good luck,
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

HP Z620 does not boot when external Seagate hard drive is connected

I'm troubleshooting an HP Z620 workstation with 32GB RAM, one 500GB HDD + one 1TB HDD running Win 7 Enterprise 64 bits, this user has 2 external USB 3.0 HDDs, one Buffalo 2TB + one Seagate Desktop Backup Plus 4TB; the problem comes when the external Seagate HDD is connected and the PC is turned one, for some reason the PC does not boots, it shows a message that states "Non-disk or no boot disk error" and sometimes it tries to boot, but then goes thru the "Windows repair option" or "Start Windows normally" routine, none of these results on starting the PC.
The only way this PC starts and works properly is when PC is started with the external Seagate HDD disconnected and then connected once the Win 7 is up and running; the problem described above does not happens with the external Buffalo 2TB HDD and the Seagate HDD have been tested throughly and no errors or problems have been detected on it.
I'll really appreciate your attention to this, as well as your prompt response.
Regards,
Gaspar Campos

Hi:
You may also want to post your question on the HP Business Support Forum -- z Workstations section where there may be more folks familiar with that issue.
http://h30499.www3.hp.com/t5/Workstations-z-series-xw-series/bd-p/bsc-272#.U1k4uv1OXGg

MSI 865PE Does not boot???

Similar Messages

Maybe you are looking for