MSI 865PE NEO FISR2 Audio not working properly

The audio on my board is not working properly. I have it set for 6 channel and am using Creative Labs Inspire 5.1 Speakers that have 3 inputs that match the 3 output jacks on the mobo. However, its just not right. It is sending anything to all 5.1 speakers and also to the proper speaker at same time. So every sound is coming through all speakers and it a tad louder on the speaker it should be coming out on. Anyone else have any clue as to what setting I can change to correct this or is this something wrong with the cmedia drivers?

The answer to all your suggestions is yes, already did it and in the demo app the sounds work fine. Its just so odd, I may just go to Circuit City tomorrow and buy another set of speakers and see if it is possibly them that are causing the issue. Then if so, I'll just return the Creative Labs ones as I just bought them 2 weeks ago and CC has great return policy
Actually, one of your questions I did not either understand what you meant or did not see the option Quote
Did you enable the output port correctly - LR to LR, surround to surround, center/lfe to center/lfe
The only thing I see is setting phones, 2, 4 or 6 channel in the cmedia control panel and then I plugged in the proper cables.

Similar Messages

HT201210 AUDIO NOT WORKING PROPERLY AFTER INSTALLED IOS7

After installed ios 7
photos not able to see fully
audio not working properly.... [no treble, no depth in sound, very low soung even the volume is full]
get strucks while playing games

This board is full of people that are update crazy...
even when they have perfectly good working systems.
i know i thought well it's just a security update not a major update.
Best advice... whenever updating the OS, unplug all
firewire devices.
will take note of that from now on.
Was this auto-update? Try downloading the file and
running the update again with all firewire devices
unplugged.
While the 828 is disconnected perform the factory
reset
again.
Disconnect the firewire cable from the 828mkII
-Press the Setup knob
-Turn the Setup knob all the way to the right
-Press the Select knob
-Press the Value knob
-Power off the interface and plug the firewire cable
back
in
-Power the interface back on
i have the original 828 not mark 2, so no reset i know of, just power on off.
After the Mac updates... reboot and plugin the 828,
see if that doesn't get you going.
pancenter-
cheers pancenter, i'll give it a whirl updating without the interface plugged in. thanks for all your help.

MSI K8N Neo 3 Sound Not Working

Hello All
I recently got MSI K8N Neo 3 but the problem is that I don't able to detect the sound card in Windows XP.
The sound card don't detect in Windows XP Service Pack 2 Till November 9 Updates.
My System Specs are
MSI K8N Neo 3
AMD Sempron 2500+ 64-bit
Kingston Value RAM 512MB
Nvidia Vanta 16MB
HardDisk Sata 250GB Western Digital
Power Supply 20 Pins (Not 24 Pins) 300 Watts (Atleast Written)
I don't know the where the problem is . The Audio is enabled in board. I have updated one motherboard bios before checking but the sound was not working so I got new one in replace. I don't upgrade the bios and install Windows XP Today but no sound.
Looking Forward to solve this problem.
Regards
Faisal

Yes, the PCI Sound card is not there. If the sound card is not detected, How I can move the sliders. The Sound icon is only show when the drivers are there and my sound card is not detected. Maybe some hardware conflict or some voltages problem. That I want to confirm. Which thing is creating problem?
Thanks for your Reply...
Further Suggestions Needed

New laptop - beats audio not working properly

Product name:HP Envy dv7t-7300 Quad Edition
OS: Windoze 8
Issue: This is a brand new notebook. We were using Skype video and the sound volume was very poor (very low). So we decided to plug in the USB-powered speakers we have used on a Dell laptop for hte last year. There was no sound. We unplugged the speakers and there was no sound from the notebook. On a whim, Iplugged the speakers back in and out and suddenly the enhanced (beats) audio started to work, but we could not control the voilume (the volume bar showed 0% but the sound was extremely loud. I played a youtubs video and the sound was still loud. I played a system sound from the control panel and the sound was extreme;y loud.. I plugged the speakers back in and there was again no sound. I unplugged them and again there was no sound.
No sound. I have rebooted twice and still no sound. Windoze 8 shows everything working fine. It apperas that ther is a hardware mechaniscal issue in the headphone plug. Also, when watching the sound controls on Windoze 8, Control Panel -> Hardware and Sound -> Sound, there are currently three sound devices onthe Volume Mixer display: S235HL, System Sounds, and HPConnectRe..... When I plug in the speaker mini-plug, the S235HL panel disappears. When I unplug the mini plug, the S235HL display momentarily (1/4 second) appears and then disappears. When I do it a third time, I get a pull down on the System Sounds which allows me to make the S23HL display appear again.
I'm pretty sure that there is supposed to be some way to control the volumn on the beats audio, and I'm pretty sure that the headp[hones jack is supposed to work properly like it has on my presios 5 or 6 laptops. Is this a mechanical issue? Or are we doing something wrong?

Hello nancyes. I understand you're having trouble with your sound.
Have you tried uninstalling the device's drivers and allowing Windows to reinstall them? Try the following.
From either the Metro or Desktop views press the Windows+X key combination. This opens the Context Menu.
Select Device Manager.
Expand the "Sound, video, and game controllers" section.
Right click on your audio device and select "Uninstall."
Now reboot your PC.
Windows will automatically install the device when it loads.
Verify whether the problem persists.
I'll keep an eye out for your response. I hope you have a great day!
Please click the white star under my name to give me Kudos as a way to say "Thanks!"
Click the "Accept as Solution" button if I resolve your issue.

Yoga 3 14 audio not working properly

Hi, Could someone please help me? I just bought the yoga 3 14 two days ago. When I am trying to listen to something with my earphones plugged in there is an echo sound. However, if i unplug the earphones and plug back in when the video player is running the echo goes away. The speakers themself have no echo sound. The same earphones are being used with my ipad and there is no echo issue. Has anybody else had the same issue. I have updated all drivers and the computer says that my conexant smart audio is the latest version.

Hi
Have you tried this:
http://h30434.www3.hp.com/t5/Notebook-PC-Sound-and-Audio/lost-sound/m-p/4231472
Regards
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

Audio not working properly

I've been having a slight problem with the audio on my iPad. I honestly can't say how long this has been going on, because it hardly does it. If I had to guess, I would say about 2 months or so. When the audio is working, it works perfectly fine. Every so often I go to listen to music, play a video, or use my sleep machine app and it does nothing. This is exactly what happens... I can use it and it works just fine, put it down for a few hours and come back and when I go to play music I tap the triangle (play symbol) and then it shows the pause symbol like it does while music is playing, but instead of staying that way it automatically goes back to showing the play symbol as if I paused it and it won't play any sounds while this is going on no matter if I try another song, a different app, or a video online. I've had someone tell me to check my volume buttons, but that is not the issue. When this happens the controlls are no different than they were when I was using it and it played just fine and I live alone so I know no one changed the settings while I wasn't using it. Also the fact that it doesn't even stay on play leads me to believe that the problem isn't entirely in the audio. It's an easy fix when this happens, I just turn the iPad off and then turn it back on and it works as if nothing ever happened. I've considered restoring it to see if that helps, but I wanted to check and see if anyone else has had this problem before. And then even if I do restore it, it may take a while to know if it solved the problem, because this doesn't happen all the time. I'm trying to avoid going to the Apple store at all costs because there isn't one where I live so I would have to drive about 2 hours or so in order to take it to one. I only want to do that if it's absolutely necessary so any and all help is greatly appreciated! Thanks!

Try this first home button and power button same time until u see apple logo come on and release it,see how you goes.

Audio not working properly on exporting keynote to Quicktime

Hello everybody,
I've created a Keynote presentation, with voiceover. It runs perfectly when launched in keynote, standalone, but as I try to export it to quicktime, the audio from an embedded video clip (just one out of 3 clips embedded in the whole presentation) stops after a few words (while the other work perfectly).
I'm going nuts! I tried saving the file afresh under different name, redoing the voiceover, tossing and reinserting that clip that stops, and save again, no luck!
Anyone experiencing the same issue?
thanks,

Hello, I have the same problem, my Quicktime movie has some of the audio files but not others. This is for a professional job so the delay while I try various settings is not helping my cause. I thought Quicktime was a well-proven solution!

Z87 MSI Mpower Max Adaptive vcore not working properly?

Hi, first time MSI MB user here.
After I finished tweaking my OC settings, I changed the vcore voltage from fixed to adaptive mode, since that is said to lower the idle temps.
However, it doesn't seem to work in the way that I thought it would.
Vcore voltage stays at the same value regardless of whether the CPU is idle or under load. I thought it would lower itself when the CPU is idle.
Am I misunderstanding something here?
Voltage check done by AIDA64 and CPU-Z 1.64.3
Below are my bios settings:
BIOS ver. 1.1
CPU Ratio Mode - Dynamic
Adjust CPU Ratio - 45
EIST and Turbo boost -enabled
Adjusted Ring ratio - auto (39x)
Adjusted Ring Frequency - 3900Mhz
VCCIN Voltags - 1.95V
CPU Core Voltage Mode - Adaptive
CPU Core Voltage - 1.25
Thanks.

Quote
Once the CPU V. is taken out of auto and set manually, the voltage isn't going to drop at idle.
Quote
That's not what I was led to believe?
Yup! Turns out your belief is correct. The rules 'have' changed with Z87!

Audio not working properly in U410. Need to retry several times, and then it works

Hi,
I have an U410 with Win 8.1. I went throught the troubles upgrading to 8.1. Installed the Conexant driver 8.65.3.53, and then de Dolby Gui.
However, when I want to: listen to music, see a film with WMP, or see a youtube video, the sound doesn't work and hence, the video doesn't start. If I click retry (or reload the web page) several times, in the end it starts working.
Any clues??
Thanks
P

It seemed that the AUDIODG.EXE memory leak issue was unrelated but...It showed crashin in the event log, and the solution for such service has sorted my sound problem
Disable the sound enhancements:
http://i.imgur.com/TTbiv35.jpg
And problem resolved.
But this is still a fix, not the solution.

1.44B Bios for MSI 865PE NEO FISR2

Can any of you mods send this file my way? My email is [email protected] Thanks.
Also, what are the supposed fixes included with this bios?

hi Misdeismo,
I'm sorry but we do not distribute beta BIOSes, with exception though. Usually when particular user has problem and we feedback to MSI, once MSI tell us to give him/her a try on the beta BIOS, there we will send the beta BIOS to him/her. Other than that, we don't. We are a bit conservative on this. 8)
Anyway, we don't stop users using beta BIOS, provided they know the risks and voiding warranty. As you see when users claim he/she has the beta BIOS and willing to distribute, we won't block or remove the threads unless being told by MSI, but MSI never do that.
I'm quite sure some users already have hand with 1.44B BIOS. Probably you can approach them. :D

MSI 865PE neo-2p, d bracket, code not in book

well suddenly my MSI 865PE neo-2p is not working, no beeps, no screen tuning on, and the d bracket2 is all wierd
lights 1 and 2 are going red and green like a schoolbus
lights 3 and 4 are red
board is out of case (on a wooden piece of wood) and the problem still percists
i have everything but the d bracket and power wires going to the board disconected
i also tried a diff PSU, no change

What I'd do is to strip off the system completely and only put CPU, and then RAM, and then display.... one by one, and see how far the system goes.
Try this
1. board + CPU --> 3 long beeps, indicating no RAM --> your CPU is fine.
2. board + CPU + RAM -> 8 long and short beeps, indicating no display, --> your RAM is fine.
3. board + CPU + RAM + display card --> see the POST screen --> everything is OK.
4. add in HDD --> detected in the BIOS --> everything is OK.
5. add everything else --> detected in BIOS --> everything is OK. Continue boot to Winblows. See anything missing.
If you can't even get out of 1, 2, or 3. Try clear CMOS.

Clip inspector in imovie not working properly - when I select a picture - and select clip adjustment it tells me that I need to select one or more clips to view Inspector tools and in a clip the audio adjustment only shows a speaker? help

Clip inspector in imovie not working properly - when I select a picture (in project library) - and select clip adjustment it tells me that I need to select one or more clips to view Inspector tools and when I select a movie clip and then click on audio adjustments the audio adjustment appears as a speaker icon and I don't know how to get to the various audio options? It was working fine one minute and then I seemed to lose the functionality. Also editing a photo in a photo or getting rid of ken burns effect etc does not seem to work. help

Can anyone shed any light on this as I am having the same problem? One minute it works fine, the next you get the error message above.
Many thanks.

Audio is not working properly and battery is not lasting

audio is not working properly and battery is not lasting over 30 mins

Hello swampdonkey,
I see that you are having a problem with the sound and battery on the computer. I would like to help with this issue but I need some information.
Can you provide the model and product number of the computer? Here is a link that shows how to find that information.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

"Itunes has detected a problem with your audio configuration. Audio/Video may not work properly".

Turned my Dell running windows 7 off 2 days ago. Turned on today. Launched ITunes and got message "Itunes has detected a problem with your audio configuration. Audio/Video may not work properly".
All my albums are there but won't play.
Deleted Itunes and reinstalled. Same as before.
Any ideas ??

Hey MrCurwen,
I was able to find an article that included the same error message you're experiencing:
iTunes for Windows: iTunes cannot run because it detects an issue with QuickTime
http://support.apple.com/kb/TS1371
According to that article, if you see the error message "iTunes cannot run because it has detected a problem with your audio configuration," QuickTime may need to be reinstalled. Please follow the steps below to uninstall QuickTime and then download and install QuickTime using the QuickTime standalone Installer.
On the Start menu, click Control Panel.
Follow the steps appropriate for your Windows operating system below.
Windows Vista and Windows 7: Click Uninstall a program (or if using Windows Vista's Classic View of the Control Panel, click Programs and Features) and select QuickTime in the list of currently installed programs.
Click the Remove button (or Uninstall for Windows Vista and Windows 7) and follow the prompts to remove QuickTime from your computer.
Download QuickTime. Note: There are two options for downloading QuickTime, be sure to select the option that does not include iTunes.
During the download:
If you choose to run the installer, proceed to the next step.
If you choose to save the download, double click the QuickTimeInstaller file, then proceed to next step.
Follow the on-screen instructions to install QuickTime.
Reopen iTunes.
Cheers,
David

K9N2G Neo Front panel audio not working

I have plugged in various cases and i/o bays into the audio connector on this mb and NONE of them work. Yes I have tried the "disable detection" option with no luck. I am currently trying to use a silverstone fp32 i/o bay that definately supports hd audio but it still doesn't work. I made no wiring mistake as it was a plug and not seperate wires.
http://www.silverstonetek.com/products/p_contents.php?pno=fp32
What do I have to do to get front panel audio that was promised with this board?
edit: you know I have NEVER had trouble with AC97 yet I have NEVER gotten HD audio to work properly EVER

It doesn't follow AC97. But it is a Realtec chip, and they often run into problems. For example they'd like their drivers installed while in SafeMode.
Where exactly did the problem come up? Is the HD controller enabled, (BIOS)?
Is this relevant, stolen from the Englizsch only manual:
"When you are playing the first audio source (for example: use Windows Media
Player to play DVD/VCD), the output will be played from the rear panel, which is the
default setting.
Then you must to select the Realtek HD Audio front output from the scroll list
first, and use a different program to play the second audio source (for example: use
Winamp to play MP3 files). You will find that the second audio source (MP3 music) will
come out from the Line-Out audio jack of Front Panel."
Off: Think this is the first time this board come before my eyes in this forum.

MSI 865PE NEO FISR2 Audio not working properly

Similar Messages

Maybe you are looking for