MSI 945P NEO-F, soundblaster problem
MSI 945P NEO-F, I945P, Socket-775, ATX S-ATAII, GbLAN, DDR2, PCI-Ex16
Intel Pentium D 930 3.0GHz Socket LGA775, 4MB, (overclocked to 3.2)
TwinMOS 1 GB - DIMM 240-pin - DDR II
Power supply 430 Watt
WD800GD Western Digital 80GB WD Raptor Serial ATA Drive
(including above raptor there are 5 internal hd's, 2 dvd burners)
im trying to install a Creative SoundBlaster Audigy 2 ZS
i uninstalled all drivers for on board sound card
and then disabled on board sound in the bios
then when i install hardware and drivers for new soundcard it doesnt work
im a newbe at this is the jumpers or something i have to change?
sorry if this is in wrong section
my system detects the soundcard but the creative control center does not detect it
"no cards found"
im running vista at moment (using vista creative drivers)
(in xp detected device and creative control center detected it too but no sound)
i may invest in new psu alright but i dont think this is the problem in this case as i tryed soundcard before i bought hard drives
the soundcard is probably 7 years old maybe its just no supported????
(it was top of its range 400 euro in its day)
Similar Messages
-
MSI 945P Neo-F - PC doesn't boot
Hey,
my PC worked for about 1 1/2 years, but a few days ago suddenly it didn't boot - the screen was black and the PC made some beep sounds (1x long, 2x short -> video card defect). I installed the D-Bracket and it says, that there is a problem with the floppy device (but i have NOT a floppy device). I did the C-MOS reset -> nothing changed. I changed the RAM sticks -> nothing changed. I unplugged all devices (but video card, CPU, RAM, PSU) -> nothing changed. What shall I do now? (I have no other video card - only AGP, but my board doesn't support AGP)
PC Data:
Mainboard: MSI 945P Neo-F
CPU: Intel Pentium D 920
Power Supply Unit: 350W (with case "Jou Jye JJ-7029B") Detailled Specifications
RAM: 1024MB (and also tested with 512MB DDR2 Corsair Value-Kit [Dual-Channel])
Video-Card: MSI NX6600 - VTD256EH passiv
And... Sound+Networkcard, Mouse+Keyboard, DVD-Drive1) Reset CMOS
2) Test with only 1 x RAM
3) Test with a better PSU
4) Test with another GPU
Btw, I'll move your thread to Pentium 4 and Core Duo section for more discussions. -
MSI 945p Neo-2 V Hanging...help!
Hi, after an exhaustive search regarding the problem and one previous post topic about the same thing happening (with absolutely no resolution, I might add) I've decided to start a new post topic to see if anything can be done.
I have in my possession an MSI 945p Neo-2 V (MS 7176 ver. 2A1 written between PCI slots) connected to various other components, all of which appear in my signature. When everything is connected and the power switch is pressed, the power turns on, the heatsink fan and computer fan both turn on and the hard drive clicks to life. After that..nothing. No bios, no "no os detected", nothing screaming at me that I done eff'd up. At this point the diagnostic bracket sits on this:
1. Red 2. Red
4. Red 3. Green
which tells me it's hanging on the video initialization. After RMAing the first board that did this to me and getting a completely new board and processor, the same thing happens.
I have tried the various steps suggested in the other topic: separate component testing, using only one memstick to get bios to post, sitting the mobo on a non-conductive surface and turning it on, checking front panel jumper connectors, but nothing seems to be working. I swapped out every component with known working ones to no avail. I swapped in every component to a working computer and separately they all work fine as well. The people I'm making this computer for have been waiting about a month for the RMA to go through and everything and I'm about to lose both my mind and reputation here. Can anyone help?
EDIT: Here's a link to the original topic I found - https://forum-en.msi.com/index.php?topic=94091.0
Other Edit: guess it's a neo-2 v, not hQuote from: cas on 22-October-08, 07:26:52
i suggest you to swap the graphic card first and see how it goes.
Prior to this incident did you OC your rig??
Alternatively try clearing cmos or jump start the psu using a screw driver
-Yes, I swapped out graphics cards, with a known working one. Still no change. I thought "broken pci-e x16 slot" but this is the second mobo of that type that's doing this, so either this particular type of mobo is crap or I'm getting shafted.
-No I never OC'd (wasn't going to try, either), since it never got past the video init, and therefore couldn't get to the bios.
-Cleared the cmos (the JBAT1 jumper I believe) and still no change.
-And I really don't trust myself with a screwdriver and electricity.
-Finally, no, I didn't update the bios. This happened out-of-box. -
MOVED: MSI K8N Neo 2 Platinum Problem
This topic has been moved to Overclockers & Modding Corner.
MSI K8N Neo 2 Platinum ProblemA lot of things could be wrong but it will be easier to figure out if we know what you did. When you say you changed settings in Bios, do you remember your last settings and what you did?
It might be helpful if you created a sig (as described in the forum rules) to show what you have in your system like my sig below. (Hint- use profile button in sign on screen.)
Things could be broken even if there is no visible evidence (such as flames or melted component) of course.
If I had to guess and your d-bracket reading is correct, corrupted bios requiring new bios chip, but let's not guess as a lot of things could be wrong and you don't want to invest in a new bios chip if the board cannot be brought back to life. Consider removing parts and testing them in an other machine. Start with CPU and memory?
Good luck. -
MSI K8N NEO Platinum Edition PROBLEM
Hi (my english is not good sorry for that)
I just got my new computer:
MSI K8N NEO Platinum Edition
AMD Athlon64 3200+
Western Digital Caviar 160Gb
PNY Verto GeForce 6800Ultra 256Mb
1GB Value Select pc3200
Levicom 500W
The Problem is that when i start the computer, it boot and die directly no bootscreen what so ever, it boot and die. i dont know what to do plz help meMake sure you have Both the ATX Wires on.. theres the Big one! (21Pins i think).. and the Small 4Pin Connector both need to be connected.. if you havent done so yet.. Another thing you could do is Take everything out and place it on a cardboard or something appropriate for the mobo.... I think your motherboard is shorting?.. if it's touching your case.. I had somewhat the same issue long time ago.. give it a try..if you want hope it helps..
-
MSI 875P NEO FIS2R AGP problems
I have just purchased an MSI 875P NEO FIS2R motherboard and there is a sticker covering the AGP slot which says "Please use only 1.5V AGP cards to avoid pernament damage to this mainboard". However, on the website it says here http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=434
"One AGP slot supports 8x/4x at 0.8V (AGP 3.0) or 4x at 1.5V
(3.3V is not supported)." I want to use 8x agp @ 0.8v and the website says this ok but the sticker on the AGP slot on the motherboard says only 1.5V. Is this a mistake on the website or on the Motherboard and is it possible for me to use 8x AGP @ 0.8V without damaging the motherboard?
I want to use an ATI radeon 9800pro.
Anybody using 8x agp @ 0.8V and have they have any problems?Assaf IS THE MAN!! His answers are NEVER WRONG.. WORRY NO MORE about the voltage...
-
MSI P965 Neo-F reboot problems
Hi,
I have a MSI P965 Neo-F motherboard in my PC, everything works great except for one thing, rebooting.
When i reboot or reset, it shuts down the operating system/BIOS, after that the PC stays on but my screen stays black.
Does anyone know a solution?
Thank you,
ghostrider090
full specs:
Core 2 Duo E6600 (overclocked to 3GHz)
MSI P965 Neo-F
2x Kingston Value Ram PC5300 1GB
Club3D Geforce 7950GT 512MB
Huntkey 450W (modded with coolermaster fan)
Samsung SH-S182D
2x Western Digital Caviar SE 250GB 8MBI dont know solution ...
i see the problem in mobo or revision of P965 itself ... there is many problems with restarts, reboots, first boot. It depend on version of BIOS you have, but i not found any version which solve this for me ...
i using v1.9 now ... and i have problem with boot after hybernation with vista..
after turning my computer off (in vista is normal to hybernate and shut down) i can boot my computer .. by its very strange. So, power comes up, but then instantly comes Windows Vista with logon screen - NO posting by BIOS, no RAID initial screen, no scaning for hardware... it comes instantly to windows - but windows are in some inconsistent state and i cant login (freeze/BSOD ... but pointer can be moved by mouse and login button shows efect if i move pointer over - so windows are in memory and working) ... in this state is HDD led all time ON (shining) ... i can shut down and boot up again and everything is OK (windows are normaly restored from disk)
with older v1.5 BIOS ... my computer goes to same state like is described here - BLANK ... and BIOS setting was reseted
so and here is one similiar problem
https://forum-en.msi.com/index.php?topic=100524.0
and one my thread .. its particly about this
https://forum-en.msi.com/index.php?topic=107722.40 -
MSI K8N Neo 2 Multiplier Problems
Check this out:
Sudhian has found problems with the MSI K8N Neo 2 clock settings that have caused memory problems for them.
http://www.sudhian.com/showdocs.cfm?aid=616this has already been shot down..
Upsetting information -
MSI k8n neo platinum post problem
I just bought a 2nd hand K8N neo platinum and I can't get it to post, I have reduced down to 1 stick of ram(tried all slots) vga and cpu running out of case. I have an ultra 600 psu that certainly should be doing the buisness as everything was fine on an NF7S-V2 up until 1/2 hour prior.
On the led device it's starting 4 red then after a couple of seconds it goes 1 red 2 red 3 green 4 red which I found relates to keyboard controller. I've tried with various keyboards but no joy. I get nothing on the screen at all but that's the next stage in post.
My memory is Twinmos 3200 twin x 2 x 512 double sided, which I saw in the sticky can be troublesome.
Any body got any ideas?i am having an almost identical problem.
First the system wont go past post,then i realised it would but only boot if i had the USB mouse unplugged (i noticed the d-brackets lights changed after i unplugged the mouse)
then i was able to get to windows, however i couldn't do much (mouse wouldnt detect if replugged, keyboard not detected - all lights off)
So i tried clearing the CMOS
now i am having the same problem, except this time i get CMOS checksum error - defaults loaded
then it tells me to press f1 to continue to del to enter setup, which i cant do since the keyboard wont work. so now im totally bamboozled
I've tried changing the PSU as well with no luck (both were 500watts)
Funny thing is, the pc having the problem is identical to the pc im writing on now, presonally i think the motherboard is not v good, since alot of people have this problem or similar to it. (and yes im using the keyboard and mouse now, that i tested on the other pc)
SPECS:
MSI k8N Neo Platinum
Powercolor Radeon 9800 Pro
AMD 64 3000+
1GB Geil Memory
Maxtor 160GB
500watt Magna Dual Fans
Will check what the D-bracket says and will report back.
ok here goes:
(with usb mouse plugged in)
1= green
2= red
3=red
4=green
(without usb mouse plugged in) - but bare in mind i cant press f1 (no keyboard) to continue else i would probably be able to get to windows.
1= green
2= green
3=green
4=red -
hi all
i have msi 965 neo-f mainboard . But when i m shutdown computer my usb port dont close.What can i do ?my system
msi 965 neo f mb
e 6300 cpu
2*512 elixir ddr667
thermaltake 560w psu
ide hdd
7600gs
my problem : I shutdown computer but usb ports not close . my pc close but my webcam sensors work. -
MSI 865PE Neo Series Restart Problem
Hello,
I have a problem on my MSI 865PE Neo Series Mobo when i restart my system using windows or by pressing ctrl+alt+del my pc won't restart and stay there forever on a black screen but when i press my reset button it will restart normally this is my one and only problem regarding this mobo... pls any help here. fix or any tips and suggestions...
(*by the way this is just my friends computer and im the one who builds it and maintain it...)
System Specs Of My Friend's PC:
MSI 865PE Neo Series Intel P4 Motherboard w/ HT Technology Support
Intel P4 @ 3GHz/800MHz FSB HT Technology
512MB DDR400
MSI NVIDIA GeForce FX 5700 @ 256MB DDR
550W PSU 12A-30no guyz im using Windows XP Pro SP1 and its not a OS problem because the first time i boot the system i have no OS yet and then i press ctrl+alt+del then my system wont restart at all even in windows ive updated all drivers and mobo bios and increasing DDR Voltage to 2.8v and disabling HT has no changed at all any help would be appreciated... i think this is some problem with MSI mobo power management that it can't match ur psu so well unlike ASUS and GIGABYTE mobo runs perfectly fine. by the way its not my pc its my friend's pc and im the one who builds and hope to fix this one and only problem... everything else is ok except for the Restart Problem!!!!
My System Spec:
GIGABYTE GA-8INXP Intel E7205 Chipset P4 MB
Intel P4 @ 3GHz/500MHz FSB
1GB Dual Channel DDR266
ASUS ATI Radeon X800XT @ 256MB GDDRIII/AGP8x
Seagate 80GB SATA HDD
Maxtor 80GB IDE RAID HDD
Microsoft Windows XP Professional Edition @ Service Pack 2 RC1 (fully updated)
My Friend's Spec:
MSI 865PE Neo Series P4 MB
Intel P4 @ 3GHz/800MB FSB
512MB DDR400 CL2.5
MSI NVIDIA GeForce FX 5700 @ 256MB DDR/AGP8x
80GB IDE HDD (x2)
Microsoft Windows XP Professional Edition @ Service Pack 1 (fully updated)
*this is not a windows problem motherboard power management or bios settings bug here..
*its my first time to handle a MSI Motherboard
*and if any guyz out there need help regarding other problems or any problems in ur pc pm me in ym @ [email protected] -
When I swicth on my pc only the front lights and the cpu fan turn on, there's no beep and no video. Then I turn it off, wait five seconds, swicth on again and then computer boots. I've change my old power supply for a 550 W 24 pin new one, the 12V CPU power connector is pluged to the board and also installed a new cooler master fan to the procesor. Please help me. My specifications are:
MB: MSI 965P Neo Bios Version 1.5
Video Card: ATI Radeon X1600 pro pci express
Pocesor: Pentium 4 3.06GHz
Memory: 1GB DDR2 Super Talent T533UB1G
Power Supply: ATX 550 W
Hard Disk: SATA Samsung 250 GB
CPU Fan: Cooler MasterPSU Specs:
RHYCOM-SGT
Input: 115V 6A 60Hz
Model: ATX550W-4
Red: +5V = 35A
Yellow: +12 = 19A
Orange +3.3V = 28A
White:-5V = 0.5A
Blue: -12V = 0.8A
Purple: 5VSB = 2.0A
Green: PS-ON
Gray: P.G
Black: GND -
AMD64 3200 + MSI K8T Neo FISR2 memory problem
I've had one KVR400X64C25/512 and it have worked like a charm. Now I've bought another one (total 1gb).
When I've inserted it and start the computer I only get the CoreCell logo scren, it do not boot correctly.
AMIBIOS is version 3.21a
I've tried the following:
* run only the new memory [works]
* run only the old memory [works]
* DIMM1 + DIMM3 [only CoreCell screen]
* DIMM1 + DIMM2 [only CoreCell screen]
* DIMM2 + DIMM3 [only a black screen]
what should I do?Quote from: Tiresmoke on 22-August-05, 21:48:12
A PSU is rated to run at +/-5% and that is well within it's rating. As for wether ists big enough there is no way we can say as you still did not give full system specs.
If it won't run with the third stick of RAM then pull it out for the moment and see if the system will boot again. If it does then during post you will see a Bios version listed. That board only supports Bios versions to 2.2 at the moment so please also list what actuall Bios version you have.
Ok, have booted with one instead of two sticks (one works, two don't, do not have three sticks)..
AMIBIOS A6702VMS v2.2 released 030405. The autodetect settings (at startup): Clock = 400Mhz, CAS 2.5 which seems correct.
More info:
AMD64 3200
MSI K8T Neo FISR2
AMIBIOS A6702VMS v2.2
Seagate 120GB SATA (no ides)
CD rw + DVD-r combo drive
floppy drive
Saphire GF6800 (no GT or Ultra)
Creative Audigy 2 Platinum Ex
that's whats running in it -
MSI K8t NEO + Audigy Boot Problem only when power is unplugged on the PSU
I ran into a really weird problem today.
I switched the ps off by reaching back and pressing the button. I repress the button to power on the ps, then I click on the button in the fron of the case to power up the machine. System keeps rebooting itself every 1 sec. Bracket shows 4 red lights. In the manual, it says it means bad cpu. I remove the audigy and it boots fine. I install the audigy, 4 red lights.
So, This time instead of turning the puter off by using the button on ps. I used the button on the case by holding it down for 5 seconds. I reboot and puter boots normally.
So the problem is, if i turn the puter off by using the button on the PS and with audigy in the syste. Nothing on screen, and puter keeps rebooting itself every one second. Solution is to turn the puter off by using the button on the case.
Has anyone ran into this problem? I have never had this kind of problem. It is really weird. Any feedback is apreciated.
Oh and it is only with audigy. I tested this with original live, and also other PCI cards like nic, and another cheap sound card. Non of these cards showed this problem.Cavemankr!
I never knew you could shut down the computer by holding down the start button for 5 seconds.... well I've never really had the need to...until I got this K8T Neo job. I wondered why it wouldn't turn off when I just pushed it. I've been using the PSU switch with these problems.
Yep! She booted right up. Audigy back in action. I also realized I had my PC hooked straight in the wall (while checking to see if my surge protector was working this weekend), so turning off the surge protector wasn't cutting power to the cheapo PSU.
So put me in your camp!
I'll just plug the PC straight into the UPS and keep power fed to the Enermax. I hope that was the cause of my keyboard/mouse cold boot problem also.
I'll assume the cheapo PSU will behave similarly. I don't really want to go through the swap again.
I wonder why that happens!
Buddy
Vor uns liegt ein weites tal
Die sonne scheint mit glitzerstrahl -
Msi k9n neo v2 display problems
having problems with this motherboard it doesnt appear to have the vga port on the back of the board, and when trying to boot with a graphics card and the monitor connected still dont get andy visual display at all.
specs are amd xp3800+ cpu
2gb ocz ddr 800mhz ram
msi k9m v2 moboard
eye-t 550w psu
asus 7600 gte gfx cardHello!
Are there any unused so called stand-offs/spacers/distanser behind the motherboard and the case?
Use a single stick, in the slot closest to the processor.
"That PSU is actually an Aspire 500watt power supply rebadged as 550watts. Has only 25 amps on its +12V rail." http://answers.yahoo.com/question/index?qid=20080913152438AAO3iEt
Suggests you try another one, of some quality.
Maybe you are looking for
-
I own a one month old HP Omni 220 PC (all in one). The operating system is Windows 7. It is connected to wi-fi network in the home. The Internet portion works fine. And, for about 30 days, it would print to our new wi-fi connected HP Photosmart 7510
-
How can i see the progress of import?
Hi. Does anyone happen to know how you can see the progress of file import on FCPX? I was importing from my camera and after a while thought FCPX was done, so i tried to eject the cam. Then FCPX prompted me that it was still busy importing. Is there
-
How to fix error messages a nd prompts upon logic pro startup
Hi all, this may be an easy one for you... When I boot up Logic 8 I have to bypass 2 hurdles before it starts up.. The first one is:"Loading audio files for unknown.exs" I see when I open up EXS24 that "unknown" patch is called up. It's just a sample
-
Something I discovered when trying to set up my Mobile Me account to ipod touch 2nd gen
I went to set up my mobile me account on my ipod touch 2nd gen and shows the option of Find my iPod. Will the find my iphone work??? I did set up an iCloud because I got an iPhone 4s today.
-
CO documents...........
Hi Gurus, As in FI we have FB03 to view the doc that we have posted. Similiarly what is the t code to view the docuemnts posted in CO. Actually i did KB11N hence i want to view the document that has been posted. Regards.