MSI AP11B Access Point ACCIDENT

Hello all, this is my first time here.
First of all, my english is bad.. so .. excuse me.!!!.
My problem:
I have purchased one AP11B Access Point to "experimentation"...
the first times.. the AP11B Work Very well. I need more distance between AP's. so
I decided put an antenna external.. but.. HERE IS MY PROBLEM.... when I resolding the PCB... i broke the OUTPUT CAPACITOR (C2).
Result: THE AP11B DOES NO WORK!... i mean.. no connect to another AP11 and this is very close..
I need some information about these capacitor... value if is possible..
o anything....
thanks!!!!!!

okay.. i fixed the AP.
now.. i have a PCI encore Wireless at 80/90 Mts...... but.. this NO connect.
i made 2 external antenna (1=AP, 1=PCI wireless).. but.. still no conecting....
any idea ?

Similar Messages

Possible to mount off the external antenna of the MSI AP11B?

Hi! I am thinking of buying the MSI AP11B Acces Point. But is it possible to mount of the external antenna, and mount another antenna to boost up the signal?
Best Regards

First I want to tell that my english is very bad ..
The external antenna basicly is a RF cable and nothing more. Put one RF conector on this short cable (aprox 5-6 cm) and attache an external antena. You must change in web settings antenna type for external ....
Inside the AP you find a internal patch antena. In diversity mode the AP use both.
Regards

MSI AP11b wireless IEEE802.11b Access Point

hi to all msi admin there and members.
im new here in this forum can anyone help me to answer my question about MSI AP11b wireless IEEE802.11b Access Point product.
I'm planning to buy MSI AP11b wireless IEEE802.11b Access Point to use my new laptop with wireless and enable me to share my internet using ap11b accesspoint..My problem is im using an usb adsl modem with (no Rj45 jack)only USB. so i can only connect my adsl modem to my desktop pc and i want to share my internet to my laptop using the wireless connection,but the problem is i dont know if this MSI AP11b wireless IEEE802.11b Access Point can help me to share my internet connection over my laptop. i have an idea and i dont think if this would work ex. if i buy MSI AP11b wireless IEEE802.11b Access Point and right after then, as usual my desktop pc is currently connected in the internet using my usb adsl modem, i want to use my desktop pc as a server using internet connection sharing(ICS) (im using WinXP) i have ethernet card that is built on my board and which ap11b available is RJ45 JACK im gonna plug my rj45 and connect it to rj45 jack of ap11b.
is this possible that im going to use my desktop pc to become serve because my adsl modem(USB)(no rj45)r and share my internet using ap11b wireless accesspoint on my wireless laptop?
anyone i need some good advice in this cases...

yes, you could use ap11b to become server and share internet for your wireless laptop.
You have to connect the ap11b to your desktop PC ethernet card via RJ45.
If the ASP can give you more than 2 IP, you can choose "Bridge model" in the "Network Connections" setup.
If the ASP only give you 1 IP, you should share the Internet Connection.
Network connections-->Local Area Connection-->right click-properties-->Advanced-->click "Allow other network users to connect through this computer's Internet connection"

How to configure MSI RG54SE II as Access Point ?

I have an msi router:
Firmware Version:
3.5.2 Build 070402 Rel.60023n
Hardware Version:
RG54SE II v1 081520C2
And i want it to configure it as an access point to a wireless network/ or another access point . Can you help me on how i do this ?
Regards,
Daniel

Hi. I Had a similar problem and found a solution. If you have another device as your primary router then:
1. connect ethernet cable from LAN port of your primary router to LAN port (NOT WAN!) of your RG54SE (I will just call it MSI).
2. go to web interface of MSI
3. if MSI has ip address in wan connection then release it. (Network->WAN) (I set my wan connection type to dynamic ip because there is no option to disable it)
4. in Network->LAN set ip address different from primary router (but in the same subnet) and out of DHCP pool
i.e. if your primary router has ip address 192.168.1.1 and its dhcp pool is 192.168.1.100-199 then you can set local ip address of MSI to 192.168.1.2
5. Disable DHCP on MSI router.
6. If your primary router also has active wi-fi then you must switch MSI wi-fi to another channel, so they do not interfere with each other.
that's it! It's simple and it works!

MSI 180 wireless LAN question (Cant connect to my linksys access point)

Hi all,
This is my first post, I couldn't find the answer, hope I am not double posting:)
I just bought myself a nice barebone MEGA 180 today together with 512Mb of memory, an Athlon XP 3000 and some other stuff.. Its up and running almost nicely now:)
The thing I cant seem to figure out is how to get my wireless network going. I've installed the driver but within my network setup I can't seem to set the security correctly. It can find my access point but it wont allow me to set the security the way I want. I use WPA Pre-shared Key with TKIP but the standard windows XP network stuff (which seems to be used here) only allows me to use normal WEP..
I had this problem with other computers aswell where the standard windows functionality just dont cut it but installing the drivers that came with those cards seem to fix the whole problem as they bypassed the standard XP stuff..
Is something similar needed for the 180?
Hope someone can help me out here, I dont want to go changing my network back to WEP.

would it be a hassle to convert to WEP encryption? at least just to see if that works?
have you looked for any updated drivers at www.msi.com.tw?

IEEE802.11 Access Point AP11B

Hello,
Does this product (AP11B) has ability to establish wireless connection betwen two (or more) AccessPoints. Something like LAN-to-MultiPoint mode.
I have one RoamAbout Access Point and I need to connect one more Access Point to my network. I need to connect these two APs because I can't establish connection with the first one so I planed to put another one in my network on place where I can connect to it.....an he must be conected with RoamAbout because it is connected to DSL link.
I hope you understand my question...if not, then I will send you a few more informations with images that can explain my problem and my need.
THANKS
Marko

with the new firmware yes. D0.0.0.22

How can I monitor the active access point + data c...

My privider (o2 Germany) requires me to use different access points (APN, proxy) on my phone (N80) depending on the type of browsing I want do do (WAP vs. "normal" access), and each of them has a "high cost trap" if I use the wrong one for the particular service.
Very annoying - up to the point that I consider not using the phone for online access at all because I'm so scared to run into uncontrollably high fees.
Anyways. I wonder if there is add-on software for my phone that helps me monitor my data connection, i.e.:
* show me the currently used access point at the top of the display (yes, I know I can go into some deep menus to look it up, but that's not very helpful or even easy to use)
* automatically disconnect when the conn is idle for a while (One of the data modes is time-based, meaning I do not want to have it open all the time by accident)
Currently, all I can see at the top of the display is that I have a data connection at all, but that does not give me enough information to know I'm in the right mode for what I'm doing.
Thomas

You can force a disconnect by pressing the red/hangup key for a couple of seconds when the phone is in the standby state.
And in menu > Tools > Settings > Connection > Packet data change the setting "Packet data conn." to "When needed" and leave the "Access point" setting there to "None".
When you or apps on your phone are not doing any data transfer, then regardless of whether it is a WAP or "full" Internet packet data connection, you should not cumulate any charges.
You can also move the Connection Manager app from the Tools submenu to the main menu, or even to the Active standby apps list (or the softkeys) for quicker access. No need to deep dive into menus for it then.
And for individual apps, you can usually set the default access point to whatever is best to use for that particular app. For the browsers ("Web" and "Services") you can also make them ask you to pick the access point every time you connect.

DigiCell - Software Access Point

How do I activate Software Accesses Point in DigiCell ??
Do I need the msi AP54G wireless to use access point in DigiCell ??
Jim

Unfortunately WPA is not available with with Software Base Station. I don't know why Apple decided to leave it out.
To get the security without WPA you may want to consider utilizing a VPN over a non-encrypted network.

K8N Neo2 Plat : how to switch the provided PCI Wifi card to access point mode ?

in digicell, I can't click on "access point mode"...
do some people have succeeded in turing the neo2 plat 54g into an access point ? If yes, how ?
thks

I also have downloaded the latest driver from the manufacturer of that wifi special card (code 2500 something if I remember well)
have you found any way to configure it to access point mode, else than with DigiCell ?
I think I will reinstall DigiCell one more time and reinstall it, I'm almost sure the problem is in it ;-)
I already has problems seeing my Acrobat Suite and tells me I don't have the Reader, it already opens IE in stead of the default browser [but it's supposed to be that way, according toi MSI], and it didn't detect CoreCenter I ghad installed previously, until I reinstalled CoreCenter over itself ;-)
What a nice tool :D

Unable to stop the event logs on access point console

Hi team,
I have an AIR-LAP1131AG-E-K9 access point having ios c1130-k9w8-mx.124-21a.JHB1.
When I am trying to take the console of it there are many logs generated like LWAPP ...Go join the controller, Discover controller etc. and the ap is unable to register to the controller(2112 with ios version 6.0.199.4). I'm trying to enter the command but there are many event msg generated....How do i stop this event log. I tried entering the command no debug all. but still there are many logs...
I want to enter the the following commands
#lwapp ap ip address <ip addr>.
#lwapp a pip default-gateway <gateway ip addr>
#lwapp ap controller ip addr <controller ip>
#wr me
Revert me back on urgent basis
Thanks in advance..

Thanks Rashika,
Now the access point got registered to the controller..This happened becuse of country Code..
I have changed the country code to UK, Belgium it started working fine.
Initially when it was IN the access point was not getting register..
But now the problem which arised is that the user is unable to get authenticated to the radius server.
Radius server is reachable and we have done every changes required for radius server authentication.
Users are getting rejected.
Customer is saying that the radius server is in IN domain and the WLC/access point is in UK,BE and hence the users are unable to connect..
Is it so??
Rply
Thanks in advance...

How do I make my AirPort Extreme a access point?

I just bought a Time Capsule and now I want to extend my range of my network. How do I make my AE an access point?

In this case, you will want to configure both base stations in an extended network.
Dynamic WDS - Extending a Wireless Network Setup
If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
Open AirPort Utility, and then, select the base station that will connect to the Internet.
Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
Click AirPort in the toolbar, and then, click Wireless.
Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
Next, select the base station that will extend this network, and then, choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
Enter the base station network and base station password if necessary.
Click Update to update the base station with new network settings.
(ref: Pages 43-44 of Apple AirPort Networks.)

How do I configure my AirPort Extreme as a wireless access point? My cable modem goes to a router, and one of those ports goes to my AirPortExtreme.

I am about to hook up my airport extreme. My cable modem goes into a router, and one of those ports will supply my airport extreme. I was told by the Apple Store that I would need to configure my airport extreme as a wirreless access point. How do I do this?

With sbcgobal I got a Gateway 2wire modem. What I would like to know is how do I set up my APE as remote?
Unfortunately, you won't be able to do this as few non-AirPort routers will work with AirPorts in a Wireless Distribution System (WDS).

Can't HP Officejet pro 8100 do wifi access point?

Yesterday my HP Officejet pro 8100 arrived and I try to connect via wifi. I thinked that It need a infrastructure access point to print via wifi.
When I powered on the printer I osserved that It create an access point autonomously with SSID: HP-Setup-7A-Officejet Pro, with IPv4 address server, etc...
I was very happy and I printed a page with my smartphone samsung s4 connected directly with printer access point (not wifi direct but standard wifi).
Today no changed occurred but I can't use printer with its own access point, but only with an external wifi access point.
Someone can help me, please? It could be an hardware problem?
Thanks,
Luca
P.S. in web server I checked that "access point connectivity" (Punto di accesso wireless connettività in Italian) is checked.
This question was solved.
View Solution.

Hello lucait
To print via WiFi you need to have a wireless router setup. Once you have the wireless router setup correctly you will have a SSID and Wepkey that will enable you to add devices to your network. The network will allow all your devices to communicate not just with each other but with the internet. At the moment your printer was not put in a network so instead of broadcasting on a network it is broadcasting on it's own network called HP-Setup-7A-Officejet Pro which is only good for a short period of time to allow you to setup your wireless. I am going to assume you have a wireless network and you are just needing assistance getting the printer setup on that network.
To set your printer up on a network you will need to reset your network defaults so your printer begins to broadcast that HP-Setup-7A-Officejet Pro network again. You can do this buy following the steps on the HP Support document Resetting the Network Settings. Once you have done this you can begin to install the software that came with your printer on your computer. You want to set the printer up wirelessly when the option arrives. The software should configure your printers wireless for you and put it on the network. Once completed you should be able to access your printer from all your devices as long as they are on the network.
I hope this helps resolve your wireless issue. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Setting up a netgear n300 as wireless bridge/access point with airport extremee

I just replaced my netgear wireless router with the airport to allow our many devices on the network without knocking each other off and also increase the speed. But would like to use the netgear as a wireless bridge or access point so that I can still connect my NTFS formatted hard drive to be shared on the network. Any suggestions would be appreciated. I can not seem to find my netgear router with 192.168.1.1 as that comes up with another device. I have tried doing this with a windows laptop in another room but can not seem to make it work. I am now hooked up directly to the airport thinking i need to do it that way and still no luck. Please help.

As long as you intend to do this over ethernet it will work.. you cannot easily wireless repeat or bridge to an apple router.. you would need specific hardware to do it.
What is the exact model of netgear you have?
The setup method depends on the functionality of the router.. but lets assume it does not have a bridge or WAP mode.
You use WAN bypass.
1. Setup the Netgear with IP address in the correct IP range for the rest of the network.. it is hard to talk generalities so lets say the apple is main router and your network is now 10.0.1.x .. then set the Netgear to 10.0.1.250 (apple uses IP 2-200 by default) you can use any value you like outside the DHCP range. Up to the limit which is 254 as long as you keep track of all static IP devices. Apply this setting and power cycle the router.. and you might need to power cycle the computer as well to pick up the new IP.
2. Turn off the DHCP server in the Netgear. You may lose connection to the netgear now.. do not worry about it.. (this can be combined with one.. if you firstly turn off dhcp before you change the IP.. but whatever is possible.. at some point you will need to change around and if you forget what IP .. you will be in a mess.. so write it on a label and stick on the base of the router.. also without dhcp you will either need to reset router to factory using reset button or use static ip on the computer. )
3. Plug ethernet from LAN of the main router to LAN of the Netgear. Reboot the whole network is often necessary.
4. In your computer plugged somewhere in the network.. open browser and go to the address you set.. 10.0.1.250 in my example.
5. You can then setup the Netgear to do whatever you like.. DIsk access is fine.. wireless is fine.. it just cannot be a router.
Many many reboots if you get lost. Hit reset and start over.

New wireless network with several access points

Hi,
We are planing to deploy a wireless network that will cover two floors consisting of about 5 or 6 Access points. It should have 2 or 3 SSID (placing the clients in 2 or 3 different VLANS).
What would be the best solution for this?
I read a lot about wireless controllers. What about an option to just buy standalone access points? Are they all configured to work with the same SSID's and on the same channel?

A centralized controller should make your life easier:
- Centralized config - set up everything on the controller and it gets applied to the AP's.
- Centralized monitoring - when someone has a problem, you can check the controller instead of having to figure out the AP to which they are connecting (computers don't always connect to the closest AP)
- Dumb AP's - if someone steals one of your APs, they will not be able to learn much about your network from a lightweight AP
- Radio Resource Management - let the controller make the channel and power setting decisions for you
- If you use PoE, you may never have to get on a ladder and use the console port of a lightweight AP. The AP is managed by the controller, and for the rare occasion that you can't get an AP to respond - just cycle the power to the AP via the switch port.
There are some downsides:
- Cost of the controller (since you're buying AP's one way or the other)
- Most cost: If your wireless network is important, then you typically want a second wireless controller as a backup
- Probably more downsides, but my brain hurts today

MSI AP11B Access Point ACCIDENT

Similar Messages

Maybe you are looking for