MSI delta ILSR no FSB 400 badge

I have bought a MSI delta ILSR moherboard and noticed that there is no green FSB400 badge near the AGP slot as seen in the picture but instead there is a black chip with mcp-t. My bios is version 7.00. Could anyone tell me why there is no green badge is this because mine in and older board as I have only bought it 1 weeks ago.
[ALIGN=center]XP 2800 333
Corsair XMS3200 256mb 400
Gainward golden FX5200 sample
XP professional
Maxtor 120gig 8mb cache[/ALIGN]

I didn't like the sticker(Orange) on my first ILSR 400 fsb Delta, I thought it had hampered the cooling the southbridge needs.
That board failed me and RMA'd it.
I have the replacement and it doesn't have a sticker but it definently is a 400fsb delta.
This board is twice what the first one was.
I hope that makes you feel better.

Similar Messages

Msi delta ilsr black screen

I have bought a msi delta ilsr and have installesd twin mos ddr400 pc3200 256mb, pny fx5200 128mb graphics card, xp2800+ and that is it and get nothing just a black screen. also I am using a new qtec 550w psu, all the fans work on the mobo but a black screen

the lights are 2 green and 2 red and then they are red and 3 green, I have tried this ram in another mobo and it works ok.
why the black screen, I hear a beep when the computer is powered up but just a black screen.
could it be the pny fx5200 graphics card???
or a dead mobo??
but the fans all work
shall I put the hard drive and dvd rom etc to the board???

Cam the MSI-Delta-ILSR unlock the multipliers?

Can the MSI K7N2-Delta-ILSR unlock the multipliers of an Athlon XP like the Asus A7N8X? If don't, why the A7N8X can do it? What's the big trick?
Can anyone answer to these questions?

Wonkanoby just answered your question here...if you want to unlock anything above the 12.5 setting in BIOS then you have to do the wire trick to your processor.
Bonz 8)

Errors with MSI Delta-ILSR

2 things is wrong:
When i start it up, it shows something like
"no drive in fastattach, bios not installed" but i´ve heard
that its nothing to worry about?
Second is that sometimes when i start and always when i restart, it only start sounding like an ambulance and the screen acts like no graphic-card is installed... also when i change FSB to make the cpu right clocked, it say i only got 512 DDR ram (i got 1024, which is showed when less clocked)...
pls help, the memory is 2x512 DDR ram 2700 Twinmos
if it´s the memory that causing trouble, i will personally
break the MB in two parts and throw it away as the junk it is...

hi
twinmos is a hit or miss i belive.
Quote
When i start it up, it shows something like
"no drive in fastattach, bios not installed" but i´ve heard
that its nothing to worry about?
this just tells you nothing is connected to raid.
but there is one thing you can do.
give us a complete list of what you have
memory cpu hd cd dvd zip
and dont forget to include 3.3v 5v and 12v rails on the psu.
but it sounds like it could be a memory malfunction.
you can always try memtest86
its a program that test your memory.
bye

K7N2 Delta-ILSR can't get IEEE 1394 working

My Mainboard K7N2 Delta-ILSR nForce2 Ultra 400 (601-6570-030)
I can't ever remember seeing the onchip 1394 controller settings in Bios.
I do remember seeing it in windows XP before I reflashed the bios to ver 7.6 using Live Update, I have read about problems with the mainboard not likeing the FX5900 Video cards, so I thought I would update the bios to save any problems.
I then re-installed XP and thought nothing of it. Everything was running well intil I wanted to do some video capturing from my camcorder. I then realised that there where no 1394 drivers installed and no controller could be found. I read the manual and it said to set the 1394 controller in Bios to Auto. When I went to Bios there was no onchip 1394 controller shown in the intergrated peripherals or any where else in Bios.
Can someone suggest what to do next please?

Try the followin steps
Hit the DEL key to go to the BIOS SCREEN
goto LOAD BIOS SETUP DEFAULTS and press ENTER
press F10 to save it to BIOS.
NOW again go to the BIOS and go to the INTEGRATED PERIPHERALS check out whether there is ONCHIP 1394
All the Best !

MSI K7N2 Delta-ILSR and Mushkin

Does anyone know if the MSI K7N2 Delta-ILSR has any issues with Mushkin ram. Specifically, with Mushkin PC3200 2-2-2? I previously had Mushkin PC2100 2-2-2 in it with no issues, but that was on a 266 FSB. On a 400 FSB, there may be issues. I dont know.

I did a little troubleshooting on my own and learned some things. I borrowed my neighbors computer (athlon xp 2600+ (266) on an asus A7N8X-E Deluxe with 2 512 meg sticks of Mushkin PC2100 2-2-2 ram). This computer has a generic 300 watt power supply, so you have to take this into account after seeing the results. First I ran prime95 on his machine and it ran rock solid. I substituted my PC3200 memory in his machine, and first ran it at 266 with no errors. Then I bumped the memory up to 333 and I got an error after 1 hour 17 minutes. Then I bumped the memory up to 400 and couldnt get past 10 minutes without an error.
I then put my proc and his memory in his computer, and my proc ran stable, and I didnt get any of the rebooting that I was getting in my machine. When I put my memory in his machine with my proc, I get about the same results as with his proc.
When I put my proc in my machine with his PC2100 memory, I still got some rebooting. When I substituted my PC3200 memory in, I still got the rebooting.
I then underclocked my processor down from 200 mhz bus to 191, and kept the ratio at 1:1 for memory, and still got some rebooting.
I then changed the ratio to 6:5, so the bus is now 159. The timings are at 5-2-2-2. The computer is running very stable and goes through prime95 with no errors.
I can put my proc and ram in my neighbors computer and get no rebooting, whereas in mine it wont stop rebooting when I have it set to spec. It looks like I have to change my mobo and/or my PSU. My PSU is an Enermax 431 watt and I have never heard of an Enermax going bad. That makes me suspect the mobo a little more, but I dont really know.
I will continue to experiment with bus speeds, ratios, and timings to see if I can get any more out of this system. But at least it is running OK now.

Does MSI produce a "K7N2G Delta-ILSR" ?

Hi all,
does anyone konw, if MSI produces a "K7N2G Delta-L" or "K7N2G Delta-ILSR" having a FSB of 400?
I didn't find any information about a Delta-Version of the K7N2G on the MSI webpages. Although a german ebay-dealer sells bundles using such a board.
( see http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=3453495856&category=23186&rd=1 sorry, it's german !!!)
I sent him an email, but he is still convinced, that this board exists.
Thanks for any replies,
af4711

no as the onboard vga boards using the vga usually cannot get past about 185 fsb any way
mine would run 200 fsb but only with a vga card in it

Internet Connection Problem on MSI K7N2-Delta-ILSR

Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
Athlon XP 2400+ Overclocked to 2205MHz
2 memory modules of 256MB 400 manufactured by Samsung
TharmalTake Volcano 11
Triplex Xabre 400 PRO with 128MB
Hercules Gamesurrround Fortissimo III 7.1
Microcom InPorte Home modem 56k
Leadtek winfast 2000 (TV/FM radio)
Acard SCSI controller (Acard AEC-6710D) for my scanner
WesternDigital WD800 GB
WesternDigital 15.3gb
Bios ver.7.4
Can anyone help me?

Quote
Originally posted by Roger Wilco
Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
Anyone else in the same boat?
Hi,
Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck
Rob

Data corruption on MSI K7N2 Delta ILSR

Hi all,
Just got my new MSI K7N2 Delta ILSR up and running.
Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum )
While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
Then the overclocking began I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
When using an FSB of 166mhz no data corruption or crc errors.
What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
Help!
gr,
Remco

Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended
Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome
gr,
Remco

MSI K7N2 Delta ILSR Memory problems

I'm trying to burn in a system in a 50 deg C (122 deg F) room for a minimum of 12 hours. The main system components are as follows:
Motherboard: MSI K7N2 Delta ILSR
CPU: AMD Athlon XP 2800+
Memory: 2x512 OCZ PC3200 EL
My problem is that the burn-in software continues to freeze up during the memory test. I've already contacted the software manufacturers and the software is stable. It's a problem with the way the motherboard handles the memory. I've tried putting the memory in dual channel configuration and changing the timing settings in the BIOS. The SPD settings are 2.5-3-3-7. Right now I have them at 3-4-3-8. It's a lot more stable than it was under the default settings but it still freezes up sometime after 7 hours. Unfortunately, I wasn't around when it froze so I don't know exactly how long it lasted. I can say that after 7 hours, it wasn't showing any slowdown in performance. If anyone could think of anything else I might be able to do to get the system stable, I would greatly appreciate it.

Thanks for the suggestions. The CPU FSB is 200, so it's already matched up there. And we have a ton of fans already. There are two in the front, 4 inside and 1 on the back. It's a custom case, 2u high. The power supply is oversized and more than adequate to provide the required power. I have four of these units running right now. Two with 2x512 sticks and two with 1x1024 sticks. For each combination, the memory clock speed for one is 166 and 200 for the other. I have been loosening up the memory timings trying to get the system stable, but it still isn't. If the power supply is good, and I'm unable to cool the system anymore due to limititions within the case, is there anything you can think of to stabilize the system. Maybe other settings in the BIOS or suggestions on how to go about getting good timings for the memory. Thanks.

MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chip

I tried to install 3 of the Crucial Ballistix Tracer (1 Gig Each) in this motherboard (MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chipset) and it will not run stabilly no matter what I tried. Is this a bios conflict with the memory? If so, are there any new bios updates? I have tried cas settings and voltage settings but nothing works. It will how ever run perfectly with only 2 sticks in single channel mode. It will not run same 2 sticks in dual channel mode. Anyone have any ideas? Anyone know of any new motherboards with maybe NFORCE 4 Chipset that support all 3 sticks of this memory and an AGP graphics card? Im thinking of a new motherboard but I still need to have AGP and SATA.
Barton 3200 core proc.
System has ran fine for a solid year until I tried new memory. Please help!

Quote from: freakytiki4u on 07-November-06, 23:42:33
Ok I tried to use relaxed FSB by -10 and relaxed mem timings but still unstable due to the motherboard trying to use dual channel memory. If you can modify the bios to where it will not have the capability of dual channel memory I truly believe it will work. Will u try this for me? I would greatly appreciate it as I am really not ready to spend all the money on new equipemtn when this suits my needs for now.
sure but as i said before this is gona be experimental and risky. Here we go:
MSI K7N2 Delta ILSR Experimental MOD E1(Disable Dual CH ability)
Procedure is automated in best possible safest way to BIOS update.
Prepare a blank diskette in a good condition(newest one etc.)
]execute file under XP will make bootdisk with automated BIOS update procedure. when diskette is ready, reboot PC and boot from FDD(floppy), wait a bit, then you will be asked for final confirmation about BIOS update process, press a key to proceed, after BIOS update is complete, ensure that you got successfully output message from flash program. then power down your PC, remove power cord from the PSU, hit power button several time to drain caps electrify, touch with hands some metal for ES discharge, and Clear CMOS.
pull back power cord, power up your PC, when you see CMOS checksum error,(expected msg) hit F1 to continue to re-build DMI pool data, then reboot and enter in BIOS, LOAD BIOS DEFAULT, and SAFE AND EXIT.
NOTE: Ensure your PC is stable before proceed with BIOS update.
NOTE: Use it at own risk, chance of failure is big, cannot guarantee results and safest as provisional mode which can guarantee it will work stable with features. also cannot test it personally before give you. (don't have mobo anymore)
Using it may end with dead mainboard (BIOS chip re-flash will be required, if somethink goes wrong)

MSI K7N2 Delta-ILSR (MS-6570) BSOD problems grrr

I recently purchased this board and although it is an awesome product, I'm having a problem with BSOD's when I play a game for a certain period of time
Specs:
MSI K7N2 Delta-ILSR (7.6 BIOS)
AMD Athlon XP 2800+ Barton
512MB (2x256MB) Samsung PC-2700 DDR memory (2.5-3-3-6 1T)
MSI 128MB GeForce4 Ti 4200 (4X AGP)
NVIDIA nForce on-board sound
Western Digital 80GB drive w/ 8MB cache
MSI X48 CD/CD-RW/DVD combo drive
Windows XP Professional SP1
PSU:
Turbolink 420watt (came with case)
+3.3V is 28A
+5V is 40A
+12V is 18A
So what happens is I get a STOP error during the game that shows the kmixer.sys driver as the culprit. Sometimes it's accompanied by PAGE_FAULT_IN_NON_PAGED_AREA too. I read somewhere that kmixer.sys has to do with windows audio and that it's a 3rd party driver issue or a memory issue. I'm using the latest NVIDIA 3.13 nForce platform drivers. I ran Memtest lastnight for 12 hours straight and 0 errors. I'm thinking the memory may not be compatible with the board nor dual channel, is this possible? I have also tried several different drivers for both video and chipset including MSI's own and I still get the kmixer.sys BSOD when playing games. My previous motherboard was an MSI KT3 Ultra2-R (MS-6380E) which I had no issues with. Any help would be greatly appreciated. Thank you in advance.
--Update--
I just tried to play a game with audio disabled and it crashed this time with DRIVER_IRQL_NOT_LESS_OR_EQUAL with nv4_mini.sys as the problem. My IRQ table shows some sharing, but device manager shows no conflicts.

Ok I tried running the DTM-CB3 module which is nForce2 approved at 3-4-4-11 2T timings and experienced the same result even at 2.6 and 2.7v. I tried both in dual-channel and same thing happened. However, I downloaded a program called Prime95 and ran the CPU torture test and the system returned a fatal error within the first few minutes. CPU Temp was at 57 C and the warning beep (set to 60C though) sounded intermittentley which is strange. I let it cool down then ran the torture test again and about 5min. later the system either seized completely or the program crashed. IE has also crashed randomly on me. I did this several times, before trying a different FSB/DRAM ratio. So I left the system at 200 FSB and used a 6:5 ratio so my memory was running at DDR333 and processor was a 3200+. I ran Prime95 again and the system locked up just as it did the other times. So after I did this a few times with consistent results. I went back and set the FSB to 166 and tried a 5:6 ratio so the memory was DDR400 and processor was the normal 2800+. I ran it again and to my suprise it passed all the tests and after an hour of this, I tried a game and that was perfectly fine as well. I checked the temps and CPU was only 45 C this time. So I'm thinking the processor can't handle anything above 50C or it's just plain overheating. I ordered a Thermaltake Silent Boost HSF today which is tested up to 3400+ so this should fix my problem. If not, then I'm going to replace the memory with a 512MB Geil PC3200 golden dragon dual-channel kit.

[MSI K7N2 Delta-ILSR] Trouble

Hello,
I have some serious trouble with my pc, my system specs are:
-Unlocked Amd 2400+ (AXDA2400DKV3C from August 21, 2002)
-Msi K7N2 delta-ilsr
-Palit GeForce FX5900XT
-Std. 512mb pc2700
-Std. 512mb pc3200
-More stuff
The problem is that I can't change the multiplier. If I change the multiplier from 15x (standart) to for example 13x, the system won't boot. Than I have to put a jumper at the 100mhz fsb setting, then I must change the multiplier back to by h/w & save the settings. So I am only able to change the fsb, but not the multiplier
Anywone who know's a solution for this problem?
Thanks,
Sape

Quote
Originally posted by Wonkanoby
http://www.nforcershq.com/forum/viewtopic.php?t=48585
i told how to there
Yes but I would like to be shore
Quote
Originally posted by Tango
How do u know that your CPU is unlocked?
Sounds like to me it is locked because you can change the fsb and not the multiplier.
Because the processor is from 2002, and then it's unlocked

MSI K7N2 Delta ILSR (MS 6570) trouble With ATA card

Hi, i have major trubble.
Ihave two 300gb, two 120gb and two 80gb harddrives + 1 DVD burner and 1 CD burner with ultra DMA 100 PCI card and it works fine without using the sata or ide3 raid function. I purchased an new PCI ATA 133 card and the system won't boot. I have tried for an long time to get the raid function to work but wihtout results with my old ATA 100 card (it works when i unplugg the ide cable from ide3).
Is there anybody that knows with type off PCI ATA 133 card that works or how too coop whith this problem.
I've got the latest bios ver. 7.8 but no difference
AMD XP2800+
Kingston 2x512mb
ATI Saphire Radeon 9600pro 256mb
Soundblaster Live Value
XP pro sp2
MSI K7N2 Delta ILSR (MS 6570)

I went to JME-Data and purchased an
True430
ATX 430 Watt Power Supply with PFC
For AMD™ and Intel® systems including
Pentium® 4
Dedicated output circuitry
Voltage feedback
Antec Low NoiseTechnology
AQ3 - Antec 3 year parts & labor warranty
True430 is a 430 Watt 6-output, dual fan-cooled ATX12V (Baby AT or PS/2 Size) power supply designed for personal computer or industrial applications.
Its ATX12V compliance allows its use with the latest Pentium 4 processors while its backward compatibility ensures its usability with any ATX-based AMD™or Intel® system
The prise 1099:-
And everything works great, Thank you very much for the tip. :-)
No more blue screen and it even works with my memory Kingston Value Ram 2x512 ddr400.
Is it possible to change the FSB from 166 to 200, and what should i think about before action. Like i said before i have an xp2800+
Alltså är det möjligt att få cpu gå på samma frekvens som minnena om man ökar FSB har några tip så är jag tacksam.
Att en nätdel kan göra så mycket helt otroligt TUSEN TACK för hjälpen till och med cpu tempen har sänkts från ca 56 till 46 grader fattar ingenting.

Msi 6570 delta ilsr/msi 6590 kt4 ultra

Hi could anyone here tell me if it is worth upgrading from a MSI 6590 KT4 ULTRA to a MSI 6570 Delta Ilsr Mainboard . Thanks in advance.

the good thing with nforce is the locked agp and pci
so as that cpu uses 13 as a multiplier you might be able to o/c it ok but not much more that the 180 or so you should get now on the old board
the main benefit with the board is with pc 3200 and an xp 2500 now as new cpu are locked
as most of them will get up around 200 fsb x11
best of all you would get soundstorm
but read as boards fussy on ram and you did not post details as asked

MSI delta ILSR no FSB 400 badge

Similar Messages

Maybe you are looking for