MSI Digicell Power on agent assistance needed

ok, so the other day i was just messin around looking at the 'power on agent'.  set ip up and tested for auto-logon, and it all went ok.  since doing this m computer now persists in turning itself on at 12:00 am EVERY day.  i went through a phase of turning the power switch off, so that it couldnt turn on, but this is starting to grate on me now, as i shouldnt have to do it.
re-installed windows yesterday, and thought everything would be ok.  got home from work earlier and the computer was on.  does anybody know how to de-activate this feature?
thanks.

cheers for that, found the "wake on alarm" setting enabled to every day @ 00:00:00.
i hadnt realised that tbe power on agent simply chenged these settings in bios, although that does explain why it was still happening after uninstalling digicell, and re-installing windows.
thanks.again.
one final thought, should there not be a bit in the user guide informing you how to de-activate this.  all i found in the guide was how to turn it on, no mention of reversing the process.

Similar Messages

  • [Request] UEFI GOP VBIOS for MSI R7750 Power Edition

    Hello, I need a GOP/UEFI Vbios for MSI R7750 Power Edition.
    S/N: 602-V271-08SC1208010276
    ROM: goo.gl/tphw4h
    (Temporarily I have no permission to post a http link, so I had to give a shorten one.)
    Regards!

    here it is
    for flashing: http://www.techpowerup.com/downloads/2306/atiflash-4-17/
    flash syntax from pure DOS, after booting from bootable USB key:
    atiflash -p -f -noaper 0 xxx.rom [ENTER]
    where "xxx.rom" will be your vbios file which you want to update

  • Upgrading From Dual Core to Quad Core on an MSI 7246 Power Up Edition

    Good day folks.
    I'm upgrading a dual core Pentium Extreme Edition 955 (3.46 GHz) to a quad core Intel QX6800 Extreme Edition (2.93 GHz) which my MSI-7246 Power Up Edition is supposed to support.
    I'm running Windows XP with all the latest patches installed.
    Are there any special procedures I need to follow to accomplish this without a hitch? I.E., I certainly do no want to have to reinstall the OS.
    I've read a couple of posts which talk about deleting the processor entries which are now correctly listed in Device Manager.
    Thanks in advance for any help.

    Quote from: Henry on 14-November-08, 13:32:48
    I forgot to add, clear CMOS wouldn't hurt before you start it up after the CPU change.
    OK. Will do. Sounds like good advice.
    Appreciate the tip.
    EDIT: As a follow-up the upgrade went smoothly except for loading the drivers for the 2nd, 3rd & 4th cores. It took me a couple of hours but I finally discovered a work around. Basically, I had to try and manually pick a driver. With Windows XP the list presented under Intel did not contain the one I wanted. However, by picking another one and then bailing at the confirmation window it would somehow put the right one in for a given core.
    Go figure ....   

  • My BB9810 refuse to load OS7.1 software on my phone after the download has completed. My phone has freezed/stucked since morning. Pls urgent help/assistant needed as I can not access/use my phone for over 24hrs now.

    My BB9810 refuse to load OS7.1 software on my phone after the download has completed. My phone has freezed/stucked since morning. Pls  urgent help/assistant needed as I can not access/use my phone for over 24hrs now.

    Hi there,
    Use the method described in the link below to get back up and running:
    http://supportforums.blackberry.com/t5/Device-software-for-BlackBerry/How-To-Reload-Your-Operating-S...
    I hope this info helps!
    If you want to thank someone for their comment, do so by clicking the Thumbs Up icon.
    If your issue is resolved, don't forget to click the Solution button on the resolution!

  • I am looking to take my Macbookpro to the philippines from USA...  What power adapter do i need?

    I am looking to take my MacBookPro with me to the Philippines.  What power adapter do I need there?  Who sells them? etc. I would prefer to keep it all apple if I can.

    Buy Apple World Travel Adapter Kit. That's all you should need.

  • Unable to execute startscen.sh for AIA PIP Agent-Assisted Billing Care 2.4

    Hi all.
    I am executing the 'Sync Collections Actions Integration Flow' of 'Agent-Assisted Billing Care' PIP to transfer collections data.
    I just install AIA 2.4 with ODI 10.1.3.5, BRM 7.4 and Siebel 8.1.1.
    After executing the following command for the first time :
    ./startscen.sh SYNCCOLLECTIONACTION 001 GLOBAL -v=5
    I obtain the following error :
    java.lang.Exception: Error: No value to affect to this variable for DefDate:2009-06-12 16:09:30.0
    DefN:null
    DefV:null
    IndStore:L
    ITxtDefT:null
    ITxtVar:null
    SessNo:23200
    VarDatatype:A
    VarName:AIA_COLLECTIONS_PROJECT.AIA_HOME
    at com.sunopsis.dwg.dbobj.SnpSessTaskSqlV.execStdOrders(SnpSessTaskSqlV.java)
    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTaskTrt(SnpSessTaskSql.java)
    at com.sunopsis.dwg.dbobj.SnpSessTaskSqlV.treatTaskTrt(SnpSessTaskSqlV.java)
    at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java)
    at com.sunopsis.dwg.dbobj.SnpSessTaskSqlV.treatTask(SnpSessTaskSqlV.java)
    at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java)
    at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java)
    at com.sunopsis.dwg.cmd.DwgCommandScenario.treatCommand(DwgCommandScenario.java)
    at com.sunopsis.dwg.cmd.DwgCommandBase.execute(DwgCommandBase.java)
    at com.sunopsis.dwg.cmd.e.i(e.java)
    at com.sunopsis.dwg.cmd.e.y(e.java)
    at com.sunopsis.dwg.DwgJv.treatCmd(DwgJv.java)
    at com.sunopsis.dwg.DwgJv.main(DwgJv.java)
    at oracle.odi.Agent.main(Agent.java)
    I read the procedure from "Siebel CRM Integration Pack for Oracle Communications BRM: Agent-Assisted Billing Care 2.4 - Implementation Guide (E14801-01)".
    Thanks,
    Patricia.

    Could you open the package which is above the scenario SYNCCOLLECTIONACTION.
    If you open this package, it should contain a variable step (maybe several) which is named like your variable.
    If you click on this step you should see in the General Tab a field Linked Object which can't be empty. Could you confirm it ?
    At Right of this field you should see a Type ListBox. Try to find the variable step which contains as Type *"Refresh Variable"*, and then right click on this step and Execute this Step, it should execute a refresh on this variable.
    After that try again to execute your scenario.

  • HT1807 I am travelling to Ireland and would like to know what type of power converter I will need in order to charge my Iphone 4S

    I am travelling to Ireland and would like to know what typw of power converter I will need in order to charge my IPhone 4S.

    The iPhone charger is capable of using any voltage from 100 to 240v.  So you won't need a converter.  All you will need is a plug adapter like this:  http://www.adaptelec.com/wa7-travel-plug-adapter-for-england-ireland-etc-type-g- bs-1363-p-3.html

  • IPhone 5. My on-off button rarely works. I can power off with assistive touch. Is there a way to power on with assistive touch, given that the icon disappears?

    My on-off button rarely works. I can power off with assistive touch. Is there a way to power on without the on-off switch?

    Depending on what you mean by power off.  If you mean putting the phone to Sleep, you can tap on the Home button to bring it back. If you turn it off completely, then the only way to turn it on is to use the physical Power Button.

  • PC suddenly restarts while playing games MSI 660Ti Power Edition OC 2GB

    Hi,
    I have the following problem since I replaced my graphics card (before 9800GTX+, now MSI 660Ti Power Edition 2GB) I got 3 random restarts while playing games. The computer is not overheating, the CPU's temperature is around 58-59 degrees after running prime95 for 3 hours. The graphics card temperature is 70 degrees after running furmark for 1 hour, the stress tests never failed, just when running games. The computer has been stable. For case cooling im using (2X12cm front, rear 1X14cm below 1X12cm and above 1X12cm +1 X14cm).
    I got two random system restarts while playing Doom 3 BFG and one system restart after playing Wolfenstein for 4 hours. The PC just restarts itself.
    What could be wrong? I have no more ideas? Should I replace the CPU cooler (im running the stock CPU cooler but all stress tests dont show overheating?!)
    Is it possible that the PSU is the reason, but it should be strong enough ...
    The system:
    GA 870A-UD3
    AMD Phenom II 1090T (cooler box)
    MSI GeForce 660Ti Power Edition OC 2GB
    12GB RAM (12GB Kit 3X4GB DDR3 Kingston Genesis 1600)
    Samsung 256GB 840pro
    WD Blue 500GB
    Thermaltake Thoughpower Q-Fan 750W PSU
    Housing NZXT Source 210 Elite
    OS: Windows 7 Ultimate 64-bit
    Thank you.

    The temps for the graphics card are quite normal. I have the same one and under load it will go to 70 to 75C, depending on ambient. What Nvidia driver are you using? Did you do a new driver installation?
    If I look at your CPU though, then you are very close to the max CPU temp and throttling may invoke the shutdown    http://products.amd.com/en-us/DesktopCPUDetail.aspx?id=640&f1=&f2=&f3=&f4=&f5=&f6=&f7=&f8=&f9=&f10=&f11=&f12=
    62C is max.
    Could also be your PSU that's not completely stable and continuous power draw may cause Overcurrent or overtemp protection. Speculating here as to probable causes.
    Another possibility is your RAM. That should normally be paired in 2's. Have you tested with only 2 modules ? Remember we don't support that MB here, but its just another test I would run. But you would know, probably having run it like that with the previous GPU.

  • MSI 670 POWER EDITION SLI HELP!

    Okay so i recently bought another MSI 670 Power Edition card. I loved my original and wanted a bit of a performance boost.
    I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
    So after a few days of testing i get about 10-20fps increase in certain games. Now after comparing my PC to other Computers with similar specs and my cards are faster than theres.
    I am not getting that much of an improvement as i should.
    On unigine Valley "Everything max at 1920x1080" i get a score of 2333 thats with both cards. To me that seems rather low or am i being silly. Also i was watching a video of a guy running the Metro Last Light benchmark and he was hitting over double what i had in terms of FPS.
    Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly. Any help would be awesome THANKS :D

    Quote from: rydek on 14-July-14, 02:34:20
    I run a MSI Z68 GD80 G3 mobo with i7 2600K. 16GB of Corsair Vengeance memory.
    Then i read that it could be because i have a sandy bridge and it doesn't utilize PCI.E 3 correctly.
    As flobelix stated before, you are limited to PCI-E 2.0 because of your Sandy CPU.
    Talking about bandwidth, SLI with PCI-E 2.0 x8-x8 is the equivalent of PCI-E 3.0 x4-x4.
    Not very good, but not very bad either.
    Quote from: rydek
    unigine valley sli - 2349
    unigine valley single original card - 1718
    Tomb Raider Tress FX off everything Ultra average FPS 62.7 - SLI
    Tomb Raider Tress FX off everything Ultra average FPS 36.3 - Single GPU original
    Your scores are ok.
    With a better CPU (i7 3770K), the scores are around 2200 (single) and 3000 (SLI).
    Those with higher scores have overclocked GPUs (and CPUs).
    Tomb Raider is one of those few games with great SLI scaling (most of the games are not).
    As you can see, you get a 70-75% boost in this game.

  • MSI GTX570 POWER EDITION helppp

    Hi, I just bought my MSI GTX570 POWER EDITION from amazon. And it seem to be some problem about this card. It runs poorly on the 3d mark11. And on starcraft2 it recommend the setting to only "meduim, suggested for 258VRM" but aren't the gtx570 is equipped with 1280VRM. Is there something wrong with my card? I have updated all the newest drivers already.
    3d result  http://3dmark.com/3d...8UuRNSxXxfNyXL9
    print scr http://tinypic.com/r/xm5wz8/7

    Quote from: freshlemon on 26-August-11, 12:27:02
    it says, "Your Score is Low Compared to Similar Systems.
    There may be a problem."
    is there anything i can do to improve the performance?
    It's not low, as you can see the most people with the same card has the same scores and they are into the same big graph as you
    Quote from: freshlemon on 26-August-11, 12:27:02
    is there anything i can do to improve the performance?
    Overclock CPU or install fastest CPU or OC the GPU further or both

  • MSI 7750 Power Edition OC.. Overheating .. please help.

    i bought msi 7750 power edition. it's idle temp remains constant at 39` and while playing games like darksiders, temp reaches 79` even with moderate or low settings. the fan on such temp reaches max speed .. 99% and makes it really noisy. is the temp normal or is there any defect wid my piece ? .. Please Reply

    Temp is absolutely normal under load. Anything below 9ß°C is nothing to worry. Try using Afterburner (>>How to use MSI Afterburner<<) and start Kombustor out of it to check tempa under maximum load.

  • MSI GE70 Power Button LED is Solid Orange

    Hello,
    My MSI GE70 power button LED is glowing solid orange as of an hour right now, is this normal?

    Quote from: Satanlygun on 26-July-14, 22:01:07
    It does this every few seconds and it just worries me a lil. Just hoping it's nothing serious. I haven't noticed anything wrong software wise but, could it be telling me something is wrong internally hardware wise?
    Thanks
    Do you have MSI Afterburner, GPU-Z, AIDA64, or any other programs that MIGHT check the GPU's on your notebook? If so, close them. See if it continues happening.
    You can also enable the "Display GPU Activity Icon in the Notification Panel" in your NVidia control panels -> Desktop -> Add a checkmark next to "Display GPU Activity Icon in the Notification Panel"
    This will add a small box down in your notification panel (by your clock) and you can mouse over it to find out what program is causing your GPU to get enabled. This can help debug the problem as well.

  • MSI GTX660TI Power Edition problems

    Hi all,
    I have a problem with Battlefield since I have installed my new GPU the MSI GTX660TI Power Edition.
    I have a Acer Aspire i7, with 6GB memory and a Corsair GS 800W, Windows 7 Home Premium
    Since I have installed my new GPU my game freezes and my systems tells me that there had been a problem with the Nvidia Windows Kernel mode and that it has been restored.
    It happens with both BF3 and BF4....while typing this topic message the same thing happens.....
    It also says Directx error....but I have the latest drivers....
    Could it be the Bios, mainboard or is my GPU not working as it should?
    Thanks for your help.

    List full system specifications, read >>Posting Guide<<

  • Msi 975x power up editon

    msi 975x power up editon  support fsb 1333 intel cpu????????

    Quote from: prozik on 11-February-07, 18:44:59
    guys look at this link http://event.asus.com/mb/fsb1333/ asus support that bu msi???
    Well, if the Asus PW5 DH can support FSB 1333, there should be nothing to prevent the 975x PowerUp to support it. It will be interesting if MSI release a FSB 1333 BIOS compatible, because at this speed (333 x 4) I have the reboot problem in all its (infamous) glory...

Maybe you are looking for