MSI FX950 Ultra AGP voltage setting please

Hi All
Anyone know what the AGP voltages should be set to in Bios for the MSI FX5950 Ultra.
Thanks

leave it be at auto 1.5 it sets itself to

Similar Messages

MSI 645 ultra xp / 2000 problem please help.

I've got 3 MSI 645 ultra mobos. I've tried every thing i can think off to get xp installed and working. I don't get as far as formating the hard disk in the setup. I relpaced the power supply with a qtec 550 watt power supply (the gold one). i've flashed the bios to 1.9, i've used different hardisks and cables. I've checked the memory PC2100 and 2700. It's a pentium 4 1.5, I've tried a 2g in it as well. I'm using an ATI radeon 7500 but have tried a s3 agp card. All the other components work fine in another machine but not on my 3 MSI boards.
Please help some one out there must have had the same problem. I'll buy the first person who fixes it cakes!!!
Ta
Gus

Hi,
I ran memtest 3.0 and there were no errors. it ran for 9 hours.
I am only using one hard disk at a time. it's set as a master on IDE1 and the CDrom is on IDE2 as a master. should I use cable select?? I also tried the hard disk and CD on ide2 and that did not work either.
Ta

MSI FX950 Ultra Bootup problem

Hi All
I have a problem on bootup where the M/B alarm will sound it will not bootup and the all case and CPU fans are running except the fans on the Video card. If I turn the pc of and on a few times it will suddenly come back to life the fans on the video card will run and the M/B will bootup into windows fine.
Has anyone else experienced this kind of behaviour and or what can be causing
this?
M/B MSI K7N2 Delta ILSR
AMD 2800+ Barton
Crucial Memory 2X 512MB DDR 3200 Dual Channel (CT6464Z40B.16T) 64MX64
MSI FX5950 Ultra VTD256
Antec True 550w Power Supply
Thanks

Andy,
If it sounds like a Siren going off, it is your CPU over heating.
If it is a beeping, then check the DLED and tell us what it says the problem is.
Take Care,
Richard

MOVED: MSI k9n ultra-2f voltage problem

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=121178.0

Quote from: BOSSKILLER on 01-November-08, 04:22:10
Look for extra vcore option in Cell Menu.
oO ok i see it , thanks

MSI 645 Ultra-C AGP voltage?

Would like to know what is the AGP voltage of the motherboard mentioned above, can't find it anywhere in the MSI site.
Asking because I'm using that mobo, and my newly bought ATI radeon 9600xt just won't work on it. When I say it won't work, I mean it crashes at any attempt to do 3d rendering(including direct3d test at dxdiag). My older card GF2MX worked pretty well.
Someone suggested that "cause new graphic cards are using 1.5V......... Old 4X AGP are only compatible with 3V graphic card. " How true is that? Could that be precisely just why my new graphic card won't work on my mobo? The board I mentioned above only support 4xagp true enough, but I'm not sure of the voltage. Does anyone know? The manual does not specify it.
Yeap, I installed and updated to the latest drivers.
Thank you!

My mobo can support 4x/8x AGP but I did use older AGP cards on it so no worries. I used to have an SIS 645D SA7 mobo from Abit that runs 2x/4x AGP Gart but also supports 4x/8x AGP cards as well as 1x/2x & 2x/4x AGP cards since 4x are found in all current AGP cards and on almost the new AGP cards, the RAMDACs are running on 1.5v(including the older GF4 series) so it's definately supported.
Just follow my suggestions on increasing your AGP Voltage for your ATI card in BIOS and use Omega drivers for ATI based AGP card. It won't harm your ATI card at all .
Lastly,I recommend that you do a clean un-installation of your old nVidia drivers or any older versions of AGP drivers before installing the new drivers. You may also be required to update your AGP Accelerator Gart driver for SIS based mobo, check the mobo's driver page for the latest version .

MSI KT4 Ultra and AGP 8X mode

Hello,
I have a MSI KT4 Ultra Motherboard but I can't set the AGP mode manually! It is set on AUTO!
I want to set it on AGP 8X!
I have a Radeon 9700 pro VGA card so it must be possibble to set it on AGP 8X
Please help me.......
Maurice Schreuder

It's at 8x already.
More info read the top KT4 Unofficial FAQ.

MBO MSI 645 Ultra and Ati Radeon x1650pro 512MB agp

I tried to upgrade my comp. with new graphic card Ati radeon X1650pro, 512Mb, AGP. X1650pro works great 3 days and then colapsed. When I became a new one from shop, It hapen the same: work great 3 days and then colapsed. I dont know what to do. I have old MBO MSI 645 ultra, intel pentium 4 on 2,4 Ghz, 1280 RAM, 80Gb + 120Gb hard drives, Samsung DVD player and LG DVD-RW... I think this motherboard dont support Ati Radeon X1650pro graphic card. I have before Ati Radeon 9600pro 256Mb and it work perfectly. Dont tell me that its time to buy all new (MBO, procesor, etc...) Regards from Croatia...

If you place Ati 9600 back in system, is all OK?
Could be faulty 1650pro card...........
Please couls you list all components in your system.........

MSI FX5200-T128[8917]Has 5200Ultra Chip Will it need AGP Voltage rise

Hi,
Some where in this forum i saw that someone is talking about after removing the heatsink of 5200 and seeing it is 5200 Ultra ...It happened to me too...
My GPU is ought to be 5200 but under the heatsink it is 5200 Ultra
soo i need help about that how can i found vga bios for to turn its bios to 5200 Ultra's
My xp drivers saying it is 5200, after i updated bios will it be turn to 5200 Ultra...?? it must be but is there any compability issues known by anyone ??
And it is 5200 Ultra why it doesn't needs external power input[From PSU] like other Ultras have ?
If i rise the AGP voltage will it be helpful to use all power of 5200Ultra ?
thanx for your time ...
Sorry for my english

Since this issue is regarding a VGA card I'm moving your thread to the VGA Forum...
Bonz

Setting up MSI 745 Ultra with Athlon xp

Hi I'm trying to set up my cpu and motherboard. I have
Athlon xp 1800+
MSI 745 Ultra motherboard
40gb Maxtor HD
256 DDR333
Inno3d Geforce 4 mx440
Win XP pro
I set my FSB to 133 so it's 266 and set ratio so that ram is 333. When I save and reset computer the settings go back to default fsb speed but XP crashes all the time.
If I switch off the computer and then back on again (instead of reset) a message says incorrect ram frequency even though it is 333 ram.
Someone said I need to set my IRQ list, but isn't this done automatically? Does anyone know what settings I should put in the bios, I'm using the latest update...
Also bios and XP says my cpu is 'mobile amd 4' not 'xp'. I have right cpu as I have checked part number
Thanks

Go to this msi forum a lot of info for the msi 745ultra
1 thing go back to the 1.3 bios the 1.4 sucks big time
http://www.ocworkbench.com/ocwbcgi/ultimatebb.cgi?ubb=forum&f=21

MSI K9N ULTRA 2F max vdimm (max DDR2 voltage!)

1st: I would like to ask you, the maximum voltage for the vdimm, that MSI K9N ULTRA-2F provides.
2nd: Will it work with OCZ PC2-6400 EL DDR2 1GB (2X512MB) GOLD EDITION GX XTC ?
Greetings from Greece

Original 7250 supports 1.80 - 2.45v in 0.05v steps , latest bios is :7250v143
K9N ULTRA 2F is MS7250-040 and use another bios , latest : 7250v31
It supports DDR2-800 (PC2-6400) DDR2-667 & DDR2-533
The OCZ DDR2 PC2-6400 Gold GX XTC Rev 2 Dual Channel 2 GB nominal voltage is 1.95 volt
Latest bios for this board is
K9N Ultra (MS-7250) V3.1 BIOS Release
1. This is AMI BIOS release
2. This BIOS fixes the following problem of the previous version:
- Update AMD NPT version.
- Update SB module version.
- Support AMD AWAY mode.
Hard to say for sure if the VDIMM is the same (max 2.45v) since no manual is availible on any MSI location for
this K9N Ultra-2F version (only found it at Japan site ) . But it should be the same .

Please advise good RAID card for MSI 745 Ultra

I wish to add a RAID controller,
so that I may have a backup of my data drive
(IBM 40gb 7200rpm ATA100).
I have purchased an identical drive
that I want to use as a mirror ("RAID 1", I believe
this is called.
What RAID controllers would be the most compatible, fastest, and most reliable?
The drive will be doing some hard work, writing audio data while it is being received in Cakewalk SONAR.
So the write speed must be able to keep up with "real time."
Thank you so much for your advice!
Here is my setup:
MSI 745 Ultra (SiS 745 chipset)
AMD Athlon XP 2000+ CPU
512mb PC-333 DDR
ATi Radeon 8500
M-Audio Delta 44 & Audiophile 2496
Enermax 350w Power Supply Unit (do you think it's enough?)
Seagate 7200 20gb HD (WinXP on Primary Master IDE)
MAXTOR 20gb 5400rpm (Primary Slave)
SONY 52x CD-rom (secondary master)
... and ASUS 40x CD-RW (secondary slave)

3Ware makes the best IDE RAID controllers, hands down.
Basically, a 3Ware RAID controller is comparable to a SCSI RAID controller except that its IDE. Just about every other IDE RAID controller, the ones you find soldered on a motherboard in particular, is crap. Go 3ware, or don't go RAID at all. You won't regret it.

MSI FX5950 Ultra VTD-256 System freeze in fullscreen 3D games

Greetings everyone
I changed from a MSI GF4 Ti4200 to a MSI FX5950 Ultra VTD-256 about two months ago and since then I have the following problem:
During any 3D game I have tested so far (which are a very few, I admit... too little time available) and after about 10 secs to 10 minutes of the game running in fullscreen, the system freezes completely (no mouse movement, no alt-tab, no soft reset) while the sound goes on looping. Games I have tested include UT2003, Star Wars Racer, Syberia. System also freezes during any version of 3DMark.
Strangely enough, I never had a problem with UT. No problem also with any game in windowed mode (where available), for instance played UT2003 in windowed mode for about an hour, then switched to fullscreen, then system freeze after about one minute. Furthermore, no prob in any 3D app (3DS, ...) or while developing 3D (OpenGL).
I have tried each and every available VGA driver, either from MSI or straight from nVidia. No change at all except with the 52.16 drivers using which the system still freezes but does not remain frozen, instead, after about two minutes a BSOD comes up announcing that...
"A problem has been detected ...
The problem seems to be caused by the following file: nv4_disp.
If this is the first time ...
The device driver got stuck in an infinite loop. This usually indicates
problem with the device itself or with the device driver programming the
hardware incorrectly.
Please check with your hardware device vendor for ...
Technical information:
*** STOP: 0x000000EA (0xFF0B5020, 0xFF6CB810, 0xFF597198, 0x00000001)
nv4_disp"
Same behaviour with the card severely underclocked through the MSI Timings control panel tab.
Other things I have done:
- Changed aperture size to various values: No change
- Reinstalled nForce2 drivers: No change
- Uninstalled and cleaned (Driver Cleaner) sound drivers, disabled SB: No change
- Disabled onboard audio and LAN: No change
- Tried all possible device driver setting for AA, filtering, rez, others: No change
- Checked memory (memtest86+): No errors
Another issue with the card that might be of use mentioning here is that the 3D!Turbo Experience app does not display Temperature, Voltage and Frequency: The respective displays are dimmed and controls are grayed.
Thanx in advance for ANY help / suggestions / similar experiences
Jorge

Greetings my good mates.
GlennVidia, a great and professional post about parametric differences! Finalreminder thanx a great lot for the versions and info! It seems that 3D!Turbo Experience does not work with 5950U eventhough it bundles with it. On my mobo the "Version 1" tag is under the VGA so this is probable why you can't see it (needless to say that I am not suggesting that I want you to remove your VGA just to give me this not-so-important info ).
Here's what happened last night.
I finally decided that I could no longer avoid what I've been avoiding since the very beginning, that is, mess with my other desktop, a Linux box with a Shuttle AK32 mobo, an Athlon XP 1800+, 256 of noname DDR and various other stuff. Another reason I didn't transfer the card to the AK32 mobo at the first instant is that I had always considered the AK32 an inappropriate testbed for the 5950. However, I felt I was in desperate need to check the 5950 on another mobo. So I set up the system above with very conservative bios settings and crap memory timing, the 5950, the Heroichi 450w psu, neither chassis nor chipset fan, and then installed WinXP Pro, SP1, DX9.0b, Hyperion 14.45 and MSI VGA 56.63.
The 5950 was running at AGP 4x, CPU at 50-52C idle, system 27C idle, voltages a little low (for instance, 11.75 for the 12+), however:
- 3DMark 2003 completes at first run (first time I was able to see the entire test).
- 3DMark 2001 completes at first run.
- UT2003 does not freeze no matter how long it runs (and I am talking extreme settings for AA, details, resolution, etc).
- Both 3DMarks keep running countless times or in loop mode without freezing.
I understand that the AGP 4x makes a huge difference on the communication between the mobo and the VGA. However, I doubt that the problem will go away on the K7N2 if I set it to AGP 4x (which I am not willing to do anyway). There are yet many tests to be done (new K7N2 bios, etc), however this is the first optimistic result I have got since three weeks now and I am quite happy about it. I might be wrong, but now I am almost 100% certain that the 5950 is not faulty.
Furthermore: On a K7N2, Finalreminder had the exact same problem as me with 3DMark 2003, that is, freezing during CPU tests (mine would also always freeze during the CPU tests and nowhere else). I think this rules out the chance of a HW fault on my mobo only.
Another pattern I have isolated is that better cooling has solved most (if not all) of Finalreminer's problems and quite a few of mine (at the beginning, 3DMark 2001 would freeze during the first run and UT2003 after a few minutes), and this too is common in both cases, Finalreminder's and mine. However, in my case, the freezing is still there even in extremely low temperature cases. To rule out the chance that temperatures go high during fullscreen 3D, I used Motherboard Monitor to log temps and voltages. Right now the log file is on a non-attached disk so I can't upload it and give you the url (I'll do that), but I can tell you that the temps and voltages are great during an entire 3DMark that ended-up freezing: CPU goes to max 58C, system to max 37C.
I think that the only hypothesis that may still stand is that MSI K7N2 Delta and MSI 5950U VTD-256 is, sometimes, a bad combination, no matter how ridiculous this may sound.
By no means am I suggesting that this is MSI's fault! As GlennVidia has explained in his latest great post about parametric differences and as my basic knowledge of electronics enables me to understand (I am a radio amateur), these are things that happen and cannot be predicted. I trust MSI and will keep trusting it.
To solve my issue, after some more testing, I am most probably going for a new mobo. I am open to suggestions and wondering if it would be a good idea to start a new thread about WORKING combinations of MSI 5950U-VTD256 and various mobos. This forum has been far too helpful for me to go out and buy something without getting feedback first .
Jorge

Msi kt3 ultra, msi gf4 4200 tvout problem

I have a msi gf4 4200 64mb card and i have a msi kt3 ultra aru and windows xp,
my problem is tv out is garbled in pal , ntsc is grey (iam in europe), the colours seem inverted blues are red, etc and theres a ghosting effect around moving images like in videos or around the cursor
Ive tried everything from default mem setting , to high performance , tried diferent driver sets , tried windows 2000, tried via chipset drivers, latest msi, nvidia gf drivers, pal b , g , i , 60hz, diferent resolutions, clone view, single output to tv, stretch view , nothing seems to fix it, the only thing that comes close to fixing it is using the tvtool http://tvtool.info/ with color fix correction activated, but the images isnt stable its got a weird strecthing, shimmering effect on the bottom half of the tv image
Iam sure that the problem is not tv or cable related because i tried a friends p4 (board msi sis 645dx) with the exact same model gf4 4200 (not my one) with my scart cable and tv set up and it worked fine.
Could it be a voltage problem? ive even tried upping agp and core voltage a bit to see if helps, and nothing

mhuizing,
nope havent tried a diferent tv , but it should work , i tested the connection with a friends computer
exact same gfx card model and it worked fine!
My old system leadtek gf3 ti200 , epox 8kha+ worked fine with this connection.
Iam using a scart cable to a video , then from the vid to the tv via antena cable
i upgraded and voila, i got some headaches for free :P !!!

Problem with my MSI KT4 Ultra

Hi all!
I have a BIG problem, I have tried to look at this board, but there is many different answers out there ;(
I have KT4 Ultra with Athlon XP 2600+
I have set FSB to 166, and when I startup BIOS says Athlon XP 2600+.
But in windows system, it only says:
AMD Athlon XP2600+
2.09Ghz !!!!
768Mb RAM
Why is windows only says 2.09Ghz??
AND, I think my system is very slow. I used to have AMD 1200Mhz. And this sytem is almost like my last computer.
My System:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive

Quote
Originally posted by swedecom
Ok, I use these settings in my BIOS, are they right for my system??
MY SYSTEM:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive
MY SETTINGS IN BOIS:
Spread Spectrum = +- 0.25%
CPU FSB Clock = 166Mhz
CPU Ratio = Auto
CPU Vcore = (V) Auto
DDR Voltage (V) = Auto
Termination Vol (V) = Auto
AGP Voltage (V) = Auto
Hope someone can help me out

Safe Agp Voltage

What is considered safe for agp voltage? It is the one setting that I have not tried messing with because I am afraid of hurting/killing my card. I am using an MSI 5900 Ultra by the way. Thanks

Keep it as close to the "Default"(1.5 v) voltage as possible....As the newer cards as your is Gets the majority of its power from the "Molex" connector.......Sean REILLY875

MSI FX950 Ultra AGP voltage setting please

Similar Messages

Maybe you are looking for