MSI GE620DX not working touchapd and bluetooth
good day
I have a question on my MSI
I have a MSI GE620DX where my motherboard deteriorated in version 2.0 which has Windows 7 64bit I bought a new board but in version 1.0 and I installed Windows 8.1 64bit there and not me Bluettoth (constantly on and off), and even not tuchpad ...
I did UPDATE BIOS to version E16G5IMS.10R (build 24.10.2012)
I tried a firmware update but I could not do this while.
I think the problem is in Windows or in BIOS, or is it due to the fact that there is another version of the motherboard?
I installed Windows 7 64 bit Bluetooth works. The touchpad does not work ... does not work with Windows installation and does not constitute key for the touchpad that are on the motherboard ... I have installed the driver MSI SUPPORT still nothing ...
I also tried connectors that go to moterboard
This is a motherboard: 63-0100-000001-00101111-102010-Chipset $ 0AAAA000_MSI GE620 / GE620DX / FX620DX / FX623 E16G5IMS VER: 1.0r 10/24/2012
PHOTO BIOS: http://www.photobox.co.uk/my/photo/full?photo_id=20705038832
When installing FIRMWARE I progressed through DOS and USB key after opening the "eCall" they wrote: "Target board FileName is different!"
SCREEN: http://www.photobox.co.uk/my/photo/full?photo_id=20705087535
I read somewhere that you just rename the file "16G5EMS1.416" but then I have written of the file is corrupted ...
And I have a plate "E16G5IMS" no "E16G5EMS1" ...
Similar Messages
-
How can I get bluetoth working again and can I go back to old jelly bean version?
Have you tried resetting network settings in settings, general, reset, reset network settings.
Complete that and from there try and go into settings after it restarts and see if you can manually connect to the network that you wanted. -
Not working USB and Bluetooth GPRS connection with LG KS360 Tribe
Hello, I just bought an LG KS360 Tribe and I can't use it to connect to the Internet. I also successfully use a Nokia phone with USB connection.
With the LG phone, when I click on "Connect", it tries to connect to the Internet for a few seconds, then the connection drops. on the phone I can see that 0KB of data have been transfered.
Bluetooth connection is the same. I use the Generic GPRS/3G driver.
Please help me with this one...
ThanksResolved! I've searched for similar problems with generic LG phones. This is what I found: http://www.taniwha.org.uk/
I've download the zip file http://www.taniwha.org.uk/files/Generic3G2007-02.zip
(just search for "Generic 3G Scripts" inside the page).
Then:
0. Unpack the zip
1. Copy the "Generic 3G *" scripts in "/Library/Modem Scripts"
2. Start the Network Manager
3. Connect the LG KS360 phone using the USB connector
4. Install the new device
5. Where you should put the phone number, write the APN address
6. In user I've inserted "none". Same thing in the password field.
7. Click on Advanced and select the driver "Other" and "Generic 3G CID1".
8. Click "OK", "Apply" and "Connect".
All works for me. -
Not working WI-FI, Bluetooth and quickly discharged battery on my iPhone 4S (MD234 / A).Switcher WI-FI is not active(gray color), Bluetooth always search(badge"network activity") and total time to completely discharge the battery is about 4-6 hours.
I'm trying to cast network configuring, reset all settings, erase all content and settings and nothing helped. I also tried to restore the iPhone, restore from backup, restore DFU mode and also nothing helped. My iPhone does not fall, not shock and not get water.
The problems started after updating to IOS 6.1.3. In all previous firmware it worked good.
I never put Jailbreak! And I buy his new!
Updates to IOS 7 will fix all the problems?
(English)
Не працює Wi-Fi, Bluetooth і швидко розряджається батарея на моєму iPhone 4S (MD234 / A). Переключатель WI-FI не активний (сірого кольору), Bluetooth завжди веде пошук (значок «активна мережа») і загальний час до повного розрядження батареї становить близько 4-6 годин.
Я намагався скину налаштування мережі, скинути всі налаштування, видалити весь вміст і налаштування і нічого не допомагало. Я також спробував відновити iPhone, відновити з резервної копії, відновити в DFU режимі, і також нічого не допомагало. Мій iPhone не падав, не стукався і не попадала вода.
Проблеми почалися після оновлення до IOS 6.1.3. На всіх попередніх прошивках він працював добре.
Я ніколи не ставив Jailbreak! І я купив його новим!
Оновлення до IOS 7 вирішить всі проблеми?
(Українська)Not working WI-FI, Bluetooth and quickly discharged battery on my iPhone 4S (MD234 / A).Switcher WI-FI is not active(gray color), Bluetooth always search(badge"network activity") and total time to completely discharge the battery is about 4-6 hours.
I'm trying to cast network configuring, reset all settings, erase all content and settings and nothing helped. I also tried to restore the iPhone, restore from backup, restore DFU mode and also nothing helped. My iPhone does not fall, not shock and not get water.
The problems started after updating to IOS 6.1.3. In all previous firmware it worked good.
I never put Jailbreak! And I buy his new!
Updates to IOS 7 will fix all the problems?
(English)
Не працює Wi-Fi, Bluetooth і швидко розряджається батарея на моєму iPhone 4S (MD234 / A). Переключатель WI-FI не активний (сірого кольору), Bluetooth завжди веде пошук (значок «активна мережа») і загальний час до повного розрядження батареї становить близько 4-6 годин.
Я намагався скину налаштування мережі, скинути всі налаштування, видалити весь вміст і налаштування і нічого не допомагало. Я також спробував відновити iPhone, відновити з резервної копії, відновити в DFU режимі, і також нічого не допомагало. Мій iPhone не падав, не стукався і не попадала вода.
Проблеми почалися після оновлення до IOS 6.1.3. На всіх попередніх прошивках він працював добре.
Я ніколи не ставив Jailbreak! І я купив його новим!
Оновлення до IOS 7 вирішить всі проблеми?
(Українська) -
Brightness control does not work with the bluetooth keyboard connected on my iPad2. Please someone could help me ?
Julien-
I have the Apple MC184LL/A Bluetooth Wireless Keyboard. The brigtness control works with mine, as do most of the other functions.
Try cycling the keyboard off and on. Hold the power button until the green LED goes out. Then press it one more time to turn it back on.
You might try resetting the iPad's network. Go to Settings-General-Reset-Reset Network Settings. Then you may need to reconnect your WiFi and Bluetooth.
If that doesn't help, try resetting/rebooting the iPad. Hold both the Home and Sleep buttons for several seconds until the Apple logo appears. Ignore the "Slide to power off" arrow. The iPad will restart in a couple of minutes. Resetting this way will not hurt anything, and sometimes clears up mysterious problems.
Fred -
Macbook Air Late 2010 model, 10.6.7, 2.13 4g ram. Trackpad is not working properly and in sometimes not at all. Need suggestions to resolve this issue? I have applied all Mac updates and still having problems with the trackpad.
The machine has a 1 year warranty, book an appointment with your local Apple Store or AASP to have it looked at.
You can try doing a SMC reset however I don't think that is the solution.
SMC RESET
• Shut down the computer.
• Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
• On the built-in keyboard, press the (left side) Shift-Control-• Option keys and the power button at the same time.
• Release all the keys and the power button at the same time.
• Press the power button to turn on the computer.
PRAM RESET
• Shut down the computer.
• Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
• Turn on the computer.
• Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
• Hold the keys down until the computer restarts and you hear the startup sound for the second time.
• Release the keys. -
I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
AndyIf you are searching the registry, check for the "Senforce" string. It should be at HKLM\Software\Senforce
Try running the install program for the ZSC with the following command line:
setup.exe /V"STUNINSTALL=1"
If you've specified an uninstall password, try this one instead:
setup.exe /V"STUNINSTALL=1 STUIP=password"" (please note the double quote at the end)
Let me know if that helped you.
Daniel
>>>
From: Andy_DeWees<[email protected] du>
To:novell.support.zenworks.endpoint-security-management
Date: 2/5/2009 12:52 PM
Subject: I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but the login prompt did not appearfor ESM client or the icon was not in the systray. Everything seems towork, besides at times (a couple times today) it terminates his ethernetcard/connection. I would re-image his computer but he has severalapplications and
I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy -
Audio is not working properly and battery is not lasting
audio is not working properly and battery is not lasting over 30 mins
Hello swampdonkey,
I see that you are having a problem with the sound and battery on the computer. I would like to help with this issue but I need some information.
Can you provide the model and product number of the computer? Here is a link that shows how to find that information.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓ -
after update to IOS 4.3.5 my Iphone incoming and out going calls is not working properly and I have to remove the SIM regulerly to conduct or receive a call
It is not practicale to do this always any one faces the same problemThere may be a problem with the SIM card. Get a new SIM card from your carrier - there should be no charge for a replacement.
If no change with a new SIM card, the standard troubleshooting steps in order are:
Power your iPhone off and on.
An iPhone reset, which is done by pressing and holding the home button and the sleep/wake or on/off button simultaneously until you see the Apple logo and then release.
Restore your iPhone with iTunes from your iPhone's backup.
Restore your iPhone with iTunes as a new iPhone or not from your iPhone's backup.
If no change after any of these steps in order, your iPhone has a hardware problem. -
I am a windows user that has converted to Mac and loving it but when I updated to Lion my wireless internet dongle would not work anymore and the Macbook Pro does not recognise the device at all so I am unable to reinstall it again. Any ideas would be greatly appreciated.
Go to Finder > Preferences then select the General tab
Make sure External disks is selected. -
I have the iPad 2 16GB, bought it in August 2011, I worked perfectly but in mid-August 2012 I took her to the store because the microphone did not work reviewed and changed me, but to my surprise that the new iPad had the problem is disconnected WIFI signal I have to be glued to the router, and I did everything he says is supported by the Apple and all other pages and forums regarding this problem is not solved and always disconnects when connected always disconnects again!! passing will be settled as no longer factory warranty although it has neither the three months I renewed new, please help because the investment has been great and I can not use only as "a mirror" I'm waiting a true solution, thanks ....
Sincerely,
CatlosThis does help me because I am pondering on wether to buy an airport extreme to solve my ipad 2 connection woes. I have an extremely old router dLink 524....but I have NEVER had any problems with it at all ever. My xbox connected great to it and netflix ran flawless through my xbox.....now I have an ipad2 and an apple tv and they are BOTH having horrible connection problems. I have read most of the forums on how to fix it by changing the settings on my router but since mine is so old I couldn't do some of the suggested solutions. So here I am debating on whether to spend all this $ on an airport extreme? I am just hoping that if I go and purchase this, my connectivity issues problems will go away like yours did. Just wondering if you have ATV as well and if the AE solved its problems? I have read about AE solving ipad2 wifi problems, I'm just hoping it will solve my ATV as well.
**Glad they didn't "moderate into extinction" your post yet, lol, Thank -
made in cosmos help please need it
using System;
using Cosmos.Compiler.Builder;
using System.Threading;
using System.Windows.Forms;
namespace IUOS
class Program
#region Cosmos Builder logic
// Most users wont touch this. This will call the Cosmos Build tool
[STAThread]
static void Main(string[] args)
BuildUI.Run();
#endregion
// Main entry point of the kernel
public static void Init()
var xBoot = new Cosmos.Sys.Boot();
xBoot.Execute();
Console.ForegroundColor = ConsoleColor.DarkBlue;
a:
Console.WriteLine("------------------------------");
Console.WriteLine("WELCOME TO THE NEWLY OS MADE BY THE STUDENTS OF IQRA UNIVERSITY!");
Console.WriteLine("------------------------------");
Console.WriteLine();
Console.WriteLine();
Console.WriteLine();
Console.WriteLine("\t _____
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t| | | |
| | |___________");
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t| | | |
| | |");
Console.WriteLine("\t|_____| |____________| |____________| ____________");
string input;
Console.WriteLine();
Console.Write("\nAbout OS : a");
Console.Write("\nTo Shutdown : s");
Console.Write("\nTo Reboot : r");
Console.Write("\nStart Windows Normaly : n");
Console.WriteLine();
input = Console.ReadLine();
if (input == "s" || input == "S"){
Cosmos.Sys.Deboot.ShutDown();
else
if (input == "r" || input == "R"){
Cosmos.Sys.Deboot.Reboot();
else
if (input == "a" || input == "A"){
Console.ForegroundColor = ConsoleColor.DarkBlue;
Console.Clear();
Console.WriteLine("\n\n\n-------------------------------------");
Console.WriteLine("version: DISPLAYS OS VERSION");
Console.WriteLine("about: DISPLAYS INFO ABOUT ANGRY OS");
Console.WriteLine("hello or hi: DISPLAYS A HELLO WORLD");
Console.WriteLine("MESSAGE THAT WAS USED TO TEST THIS OS!!");
Console.WriteLine("-----------------------------------");
Console.Write("You Want to know : ");
input = Console.ReadLine();
if (input == "version"){
Console.WriteLine("--------------------");
Console.WriteLine("OS VERSION 0.1");
Console.WriteLine("--------------------");
else
if (input == "about"){
Console.WriteLine("--------------------------------------------");
Console.WriteLine("OS IS DEVELOPED BY Qazi Jalil-ur-Rahman & Syed Akber Abbas Jafri");
Console.WriteLine("--------------------------------------------");
Console.Write("Want to go back to the main window");
Console.Write("\nYes : ");
string ans = Console.ReadLine();
if (ans == "y" || ans == "Y")
goto a;
Thread.Sleep(10000);
else
if (input == "n" || input == "N")
Thread.Sleep(5000);
Console.Clear();
for (int i = 0; i <= 0; i++){
Console.Write("\n\n\n\n\t\t\t\t\t ____ ____ ___
Console.Write("\n\t\t|\t\t | | | |
| | | | | |");
Console.Write("\n\t\t|\t| | |---- | |
| | | | | |---");
Console.Write("\n\t\t|____|____| |____ |___ |____ |___| | | |___");
Thread.Sleep(500);
Thread.Sleep(5000);
Console.Clear();
BootUserInterface();
Console.ReadLine();
// Form1 fo = new Form1();
else{
for (int i = 0; i <= 5; i++){
Console.Beep();
Thread.Sleep(1000);
goto a;
while (true);
private static void BootUserInterface() {
Thread t = new Thread(UserInterfaceThread);
t.IsBackground = true;
t.SetApartmentState(ApartmentState.STA);
t.Start();
private static void UserInterfaceThread(object arg) {
Form1 frm = new Form1(); // use your own
Application.Run(frm);
Hi
Jalil Cracker,
>>when user pres n then it must go to a form but error arises and not working good and threading is not respondin
Could you post the error information? And which line caused this error？
If you want to show Form1, you can use form.show() method
Form1 frm = new Form1();
frm.Show();
In addition, Cosmos is an acronym for C# Open Source Managed Operating System. This is not Microsoft product.If the issue is related to Cosmos, it would be out of our support. Thanks for your understanding. And you need raise an issue at Cosmos site.
Best regards,
kristin
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
My bridge is not working normally and keep given me this message : bridge encountered a problem and is unable to read the cache . Please try purging the central cache in cache preferences to correct the situation
And did you then actually purge the cache?
Please realize that you have given ZERO details.
BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
a screen shot of your settings or of the image could be very helpful too.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
Hello, it's been 5 days now since my imessage has not working..and i have chatted to the costumer for two times. I took thier advice and instructions just to enable to send and receive on it but unfortunately until now its still NOT working. Is there anybody who could help me please?
Try this even if you have already. Just make sure to follow the steps specifically.
Go to settings > Facetime > send and recieve > tap on your apple id and sign out. If your not signed in then that will work as well.
Go to settings > Messages > sent and recieve > tap on your apple id and sign out.
Restart the iPad by doing the slide to power off setup. Just hold the power button on the top right till it turns off.
After the iPad has been restarted:
Go to settings > Facetime > and sign in
Go to settings > Messages > and sign in
Wait about 3 min then restart the iPad again. Same instructions as above.
When you restart you should be able to use messages again. If not then call support again and talk to someone higher than the first level support they have. -
When I try to uninstall iTunes I get a message saying iTunes 64 msi can not be located and I should enter an alternate path. How would I know where it it is? I get the same message when trying to install the update to iTunes 10.6.1.
Download the Windows Installer CleanUp utility from the following page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
To install the utility, doubleclick the msicuu2.exe file you downloaded.
Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?
Maybe you are looking for
-
Different ways to call a servlet
Hi, I have created a servlet which generates a PDF report. The servlet is called through a html standard link. All this work well but I would like to avoid calling the servlet through the url because it risks to change. There is means to call a servl
-
How to open 8.0 project from generated files
Hello- Is there a way to work from generated files in a project after it is published?? We lost the 'originals' which were on a hard drive that got zapped. Now I am scrambling to figure out how to open it when I can't see the xpj file??? I know th
-
How good is RAW photo editing in iPhoto '08?
Can it compete in any way with Aperture? Is it worth it? I was settled on Aperture until this came out. It has some feaures that make it seem a little Aperture-ish, or Aperture-lite. I don't do much RAW editing, but I up the saturation, play a little
-
ORA-00904: "T1"."TOT_COSTS_UPLIFTED_FUEL_QTY": invalid identifier
Please help to solve this error: ORA-00904: SQL> select "c31" "c1", "c30" "c2", "c28" "c4", "c29" "c6", "c25" "c8", "c34" 2 "c10", 3.4592 "c12", "c35" "c14", case when "c27"<>0 and "c28"<>0 then 3 ("c27"*"c35")*"c25" else 0 end "c16", "c26" "c18", ("
-
Hi All, We have developed a custom AME approval hierarchy for iRecruitment. The hierarchy includes delivering FYI notifications as well. The FYI notification gets generated we can see the FYI notification when we login to oracle apps. But it is not g