MSI GF615M-P33 problem with sb audigy se

Hi everyone
First of all in case it's useful, here's my system:
Windows xp sp2 32bit
AMD Athlon X2 240 2.8GHz Socket AM3 2MB
MSI GF615M-P33 GeForce 6150SE Socket AM3
Asus Radeon X1550 512mb (old card works fine)
Sound Blaster Audigy SE
Crucial 2GB DDR3 1333MHz/PC3-10600 Memory CL9 1.5V
0 Maxtor 80GB SATAII 7200rpm 8MB Cache
1 Maxtor 250GB SATAII 7200rpm 8MB Cache
G7 680 watt psu
So this is my third msi board and everything is fine except windows is giving me this error code: Your computer's system firmware does not include enough information to properly configure and use this device (sound blaster audigy). To use this device, contact your computer manufacturer to obtain a firmware or BIOS update. (Code 35).
I had a look at what I think is the bios version according to the boot screen A7597nms V2.0 123109 (does this look right?). Also, the advertised version of my board had a red pcb, mine is black and the version is 1.2, don't know if that's important, mentioning anyway.
Now I know the card works with the board because I did something slightly different, (just to see if it would work and save time). After building the computer I didn't reformat the hard drive from the previous mother board, just plugged it in and installed the new chipset drivers etc. Everything fine, soundcard working, except the cpu was only in single core and running very cool; less than 30 degrees c. So, decided to reformat properly, all good, cpu in multi and running around 40 degrees c, but just this problem with the sound card.
Another difference I notice is in windows control panel under Power Options I can't enable 'advanced power management' the option isn't there, so have to switch of the computer manually (which isn't a major problem). In the bios I always disable ACPI as I run a lot of audio processing software and according to some stuff I've read, can cause problems with irq's and all that technical stuff that I don't know much about.
Anyway, to the point. My question is: do I need to update the bios to 2.1 or would it be better to buy a new sound card. I've tried various bios settings and updating the drivers but makes no difference. I've even reinstalled windows with acpi enabled, again, the same error code.
Any help/questions much appreciated. Hope I've explained this well enough.

Quote
So this is my third msi board and everything is fine except windows is giving me this error code: Your computer's system firmware does not include enough information to properly configure and use this device (sound blaster audigy). To use this device, contact your computer manufacturer to obtain a firmware or BIOS update. (Code 35)
Quote
In the bios I always disable ACPI as I run a lot of audio processing software and according to some stuff I've read, can cause problems with irq's and all that technical stuff that I don't know much about.
What HAL is installed? Look in device manager under "Computer"

Similar Messages

Msi gf615m-p33 - incompatible with GPU?

so i bought that mbo, and i bought at first 9800 GT . and,,,, it wont work.. no boot, no any sound, no picture...then i bought xfx 550 psu, and still no working..than i tried ond 3850 gpu,and it works..... but today i bought 4890 gpu,and again, it wont work!! .. same like 9800 .. no boot.. no nothing.. im mad.. i tried both gpu at my friend ,and it works.. so, its mbo problem... i updated bios with msi online update,,and nothing.. so..whats is wrong with this mbo?

I think that is because of the testing method. I think this series has no separate transistors/regulators for 3,3 and 5 volt lines, but rather a "converter" from the 12 volt. Usually that leade to high efficiency and "stable" power.
The thread sounded PSU:ish from the start, but you have to trust a few things in life, and I put some truxt in XFX Core series. - Made by Seasonic, which is usually a sign of quality. The problem is we can't say what PSU is in exer's box...
...Intermissing...
Here is from the 550 Watt test, by Jonnyguru:
"Seeing how my test results were not consistant with other review sites reviewing the same two power supplies, I have retested both units. The results are on the next page....."
http://www.jonnyguru.com/modules.php?name=NDReviews&op=Story3&reid=225
Long time has passed, but my opinion about XFX Core Edition was formed I believe from this review:
http://www.hardwaresecrets.com/article/XFX-PRO-650-W-Power-Supply-Review/1165/10

MSI GF615M-P33 without LAN driver.

I put together a pc with the MSI GF615M-P33 yesterday. With the CD from MSI I was able to install the drivers for Chip, Sound, CPU.
Now, I was not able to press neither the "LAN" or "RAID" buttons in the program to start installing the drivers for this.
The only LAN driver I found for MSI GF615M-P33 was at msi.com. But only for 32-bit Vista. I use Windows 7 64-bit.
Can someone tell me where to find drivers? Really need to get my webconnection up and running as fast as possible!
PC Specs
# Cooler Master Elite 310 Black/Blue Fans: 1x 120mm rear, ATX, mATX, 2x USB, 1x Audio, 17 dBA
# Silver Power SP-400P2C 400W Super Low Noise, 2x PCIe, 12cm Fan
# AMD Athlon II X2 250, 3,0Ghz, AM3, 2MB, 65W, Boxed
# Kingston ValueR. DDR3 1333MHz 4GB, CL9, Kit w/two matched ValueRAM 2GB DDR3
# MSI GF615M-P33, Socket-AM3, m-ATX, GeForce 6150se, DDR3,SATAII, GbLAN, PCI-Ex16
# Sapphire Radeon HD 4670 512MB GDDR3 PCI-Express 2.0, DVI-I, native-HDMI, HDCP, Lite-Retail
# Seagate Barracuda 7200.12 500GB SATA-300, 16MB, 7200RPM

Quote from: Fredrik on 19-January-10, 05:13:18
I think you have to find out at Realtek's site if they have come up with drivers:
"Supports 10/100/1000 Fast Ethernet by Realtek 8211CL."
...Can't find any by a quick glance. It wont work with Windows 7 own drivers?
The Realtek's pages has no drivers for the 8211CL, tried that yesterday.. Doesn't seem like Win7 works with it...
Quote from: adamantine on 19-January-10, 05:21:35
I'm not sure, but the standard nforce driver may have installed the LAN drivers for you.
I just downloaded newest nForce and geforce drivers fron NVIDIA, everything including LAN works except audio (which I disabled anyway). It shows up on device manager as "nForce Ethernet" or something like that.
Good luck!
I will try that.
Thanks for both answers!

Sound problem with the Audigy 2 va

Hi, I have asound problem with the Audigy 2 value. most of applictaions I played got sound. however, when I play FS2004, the sounds come on only the ATC voice in game playing, 5sec after the voice over, the sound is gone, and only when another voice is playing, the sound comes out. please helps out.

Shedden,
I would suggest going ahead with a cleansweep and reinstall of the card. Here are instructions on how to cleansweep and reinstall your sound card:
http://us.creative.com/support/kb/ar...asp?l=2&sid=72
Jeremy

Weird problem With my Audigy 4

Hi all, I have a weird problem with my audigy 4. When I install the Nvidia IDE and Sata driver for my motherboard, I get sound problem in BF2, It glitches, I don't here my gun, well it's all ****ed up. Does anyone know why?Thanks in advance.

I have had every iphone model ever made. I have never had a problem like this before. It appears that there are small spots all over the screen. Not to be confused with the "yellow spots" other iphone 4 user have been reporting due to the glue not drying before they reached the customer. This is a different type of spot. I would compare it to a petrie dish that scientist test for things in.
The only thing I can think of is something is happening with the coating over the glass (oleophobic coating maybe braking down?). It only happened on the front screen and not the back glass. You can get the spots to go away when you use a micro fiber cloth to remove the natural oil from your face against the phone. The minute you start using the phone again, they appear. They are kinda annoying and make your phone screen look dirty and have a weird glare in it when your in the sun.
I made an appointment tomorrow to go to the apple store to see what they can tell me. Hope fully its nothing major. The worst thing that could happen is the phone gets replaces by another. Ill keep everyone update.

HELP! MSI GF615M-P33 7597 Ver 1.3 BIOS needed!

Hallo!
Please help. on GF615M-P33 7597 Ver 1.3 (!!Ver1.3!!) BIOS crashes :( But Bootlock is alive and Ctrl+Home works ok.
I cant find BIOS for this motherboard.
Please make a dump of this bios if you have same ver 1.3 http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=171&prod_no=2134 motherboard and send me **Email-Address removed to protect user from spam**
best regards! Pavel

http://www.msi.com/product/mb/GF615M-P33-V2.html#/?div=BIOS
sn: 601-7597-100b1008615634
when i put the 3 files on my usb stick, an then go on my msi pc i put in usb port and go on my pc.
they print me on the screen:
"FILE NOT FOUND
PLEASE COPY LAST BIOS.... ..."
i would like to download the bios from the site but is only live update5.
My MSI pc is bios cleaned in the moment i work with him i'm not put upgrade or anything else but i work for my office and in a moment they say me this....
:bonk:Virus??? i'm not understand!!!!

Problem with microphone, Audigy 2, and a Dell (not the same problem as the 8 million other topi

Hello,?I recently reformatted my hard dri've and had to reinstall drivers for nearly everything, etc. I have a Dell Dimension 4600, and an Audigy 2 sound card. My microphone worked fine before the reformat and then it was broken. Its not that it wasn't picking up my voice (I have read that the typical problem with Dell computers and microphones was that you had to almost scream into the microphone to get it to hear anything). When I tried to record something, it would record what was coming out of my speakers, and not what I was saying (no matter how hard I yelled). So, when I was playing Counterstrike, everybody heard my gun shooting and grenades exploding etc. instead of my voice (which was what was coming out of my headphones). So I downloaded the ISO available here and through some complicated, random process of uninstalling and reinstalling the various sound drivers I found on the internet, I managed to get my microphone to work perfectly. I changed some settings before I went to bed on Sunday night, and when I tried to use my microphone on Monday it didn't work again (and I had the same problem as before).
So I reformatted again and am trying to figure out what order I installed and uninstalled etc.
So my question is, has anyone else has this specific problem (when attempting to record it records what comes out of the speakers/headphones and not what is being said into the microphone) and remembers how to fix it's? What I did was really bizarre, something like downloading Dell drivers, installing them, uninstalling them, downloading Creative drivers, installing them, installing Dell drivers on top of them, uninstalling both, downloading the ISO, reinstall the Creative drivers, install the files from the ISO, or something like that. Obviously that includes a lot more steps than are needed and because part 3 of the ISO is currently down (I don't have a CD burner so had to redownload the whole thing (I just used a CD emulator last time)) I can't work on it right now :/

HalberdBlue wrote:
Hello,I recently reformatted my hard dri've and had to reinstall drivers for nearly everything, etc. I have a Dell Dimension 4600, and an Audigy 2 sound card. My microphone worked fine before the reformat and then it was broken. Its not that it wasn't picking up my voice (I have read that the typical problem with Dell computers and microphones was that you had to almost scream into the microphone to get it to hear anything). When I tried to record something, it would record what was coming out of my speakers, and not what I was saying (no matter how hard I yelled). So, when I was playing Counterstrike, everybody heard my gun shooting and grenades exploding etc. instead of my voice (which was what was coming out of my headphones).So I downloaded the ISO available here and through some complicated, random process of uninstalling and reinstalling the various sound drivers I found on the internet, I managed to get my microphone to work perfectly. I changed some settings before I went to bed on Sunday night, and when I tried to use my microphone on Monday it didn't work again (and I had the same problem as before). So I reformatted again and am trying to figure out what order I installed and uninstalled etc.So my question is, has anyone else has this specific problem (when attempting to record it records what comes out of the speakers/headphones and not what is being said into the microphone) and remembers how to fix it's What I did was really bizarre, something like downloading Dell drivers, installing them, uninstalling them, downloading Creative drivers, installing them, installing Dell drivers on top of them, uninstalling both, downloading the ISO, reinstall the Creative drivers, install the files from the ISO, or something like that. Obviously that includes a lot more steps than are needed and because part 3 of the ISO is currently down (I don't have a CD burner so had to redownload the whole thing (I just used a CD emulator last time)) I can't work on it right now :/
Actually, it's not a problem but a setting. On surround mixer .rec source setting --> when you set it to What U Hear everything you hear becomes recorded --> for microphone recording set it to microphone (also set "monitoring while recording" on/off).
jutapa

Problems with new Audigy driv

<p class="MsoNormal">I have just installed a Sound Blaster Audigy Platinum Model SB0090 to replace my old SB Li've. When upgrading from older Audigy drivers to the latest drivers available on the Creative support website, I find that they cause serious problems with my 4. digital speaker system (Boston BA7500G). With either of the newest drivers installed, when I adjust the volume using either the Creative Surround Mixer or the Creative Remote Control, it causes the rear speakers to stop working. Closer investigation revealed that moving the volume slider in Creative Surround Mixer had a strange effect in Windows Audio Control Panel. Upon opening the Speaker Volume tab in Windows Audio Control Panel, it revealed 8 speaker channels (suggesting that it detected the Audigy card as a 7. when in fact it only supports? 5.). When I moved the volume slider on the Creative Surround Mixer (in either direction) it had the effect of moving all but three of the speaker volume sliders in the Windows Audio Control Panel (Right Channel, Left Channel and Channel 8) to zero, with the result that the rear speakers stopped working. Inm other words, Windows was insisting that the speaker setup was 2. and not 4. as in the Surround Mixer selection. ?It made no difference if either or both of the checkboxes ?Synchronize with Windows Control panel? in Creative Audio Console or ?Move all sliders at the same time? in Windows Control Panel were checked or not. This problem is present in both SBAX_PCDRV_LB_2_8_000.exe and SBAX_PCDRVBETA_US_2_8_000.exe. It does not appear to be present with the older driver SBAX_WBUP2_LB_2_09_006.exe, so for now I have rolled back to that. In fact, with SBAX_WBUP2_LB_2_09_006.exe Windows Audio Control Panel only shows 2 channels in the Speaker Volume tab; Left Channel and Right Channel, but all speakers in my 4. system work and the controls in Creative Surround Mixer and Remote Control all work fine. I would like to be able to take advantage of the fixes available in the two newer drivers but they cause me serious problems. Can anybody help? Finally, the presence of a beta driver on the website suggests that a newer version is coming soon. I wonder?if this issue be addressed with the new driver.

I have some problem as you with new drivers SBAX_PCDRV_LB_2_8_000.exe and SBAX_PCDRVBETA_US_2_8_000.exe. Only in my case I use SB Audigy and headphone 5.. Always when I check 5. in Audio Console it reset to 2.. I can set 2. or headphone only.Message Edited by AlkaliX on 09-3-2008 09:53 AM

The problem with Creative Audigy SB0090

Hello.
Installed Creative Audigy SB0090.
Switched off the built-AC97 in the BIOS.
Do not hear a sound. There is a hiss, and through him to hear the faint sound. Plug speakers SVEN IHOO 5.. Help to understand and [email protected]

A can not be compatibility problems with Behola TV 505 FM?
where you can download this version?

Problems with my Audigy X-FI Platimun

Recently I bought the Audigy X-FI Platinum for my pc, replacing my old good Audigy Platinum.
These are my rig specs:
Asus A8N SLI Premium
AMD 64 3800 X2 Processor
ASUS GT6600 vcard
80 GB SATA Drive
60 GB SATA Drive
OS: Windows XP Professional SP 2 32Bit
Desktop Theater 5.1 DTT2200 Speakers.
The problem is that when I am viewing a DVD, playing any game or just listening mp3 the audio just go. I have to "play" a little with the cables that connect my speakers to the audiocard in order to get sound again. But when I hooked the speakers with my Audigy Platinum again I do not experience any kind of problem.
Any help would be appreciated!

No modified .inf file will enable the DTS or Dolby tabs in the Dell OEM XremeMusic. No hacked drivers will do either (maybe in the future).
I have the same card, and I've experimented a bit with it (I bought it to use it rather than to spend my time trying to enable functionalities that I actually don't miss), with the help of some "experts".
The only way to enable those functions involve component soldering/de-soldering on the PCB and firmware flashing.
This is not big issue as there's no warranty to void. Creative won't support this card, neither will Dell unless it was shipped as part of/upgrade of one of their systems.
But if you don't have the relevant skills and tools, unless you want to start hard-modding as a hobby, is just not worth it.
BTW, in my case the total cost was $9.00 deli'vered, so... what can I say? :P
Edit: I just saw in your screenshot the shortcut to "Owner's Manual" so I guess yours is a Dell system. Forget about hard-modding if you don't want to void your warranty big time.
And don't bother downloading the retail CD either. Save the bandwith for something else. There's a hack to install the applications of the retail CD on OEM cards, but it will make no difference whatsoever. It won't enable any extra functions on the card.
You can pick up the phone and complain to Dell if they didn't tell you about this "little" issue though. I have never bought a Dell desktop, so I can't really tell if they warn the customers about the card being OEM and limited in functionalities or not.Message Edited by MrToad on 08-23-2006 05:32 PM

MSI GTX560-TI Problem with Windows 7 Aero

Hi,
I received today my new MSI GTX560-TI , the problem is on Windows 7, when i point to a taskbar button, i can't see live preview of open windows anymore (it worked with my old ATI Radeon 4890)
- MSI N560GTX-Ti Twin Frozr II OC
- Nvidia ForceWare 266.66
- Windows 7 x64 SP1
Is a problem with the nvidia forceware drivers ? , it's been a while since i've used them (MSI Geforce 6800GS )
Thank you.
(Bios not yet flashed )

If you've moved from an ATI card, perhaps there are leftover driver fragments. Uninstall your current graphics card drivers, run >>Driver Sweeper<< and install the drivers again.
Does anything pop up when you hover over an active program?

MSI 645Ultra and problem with memory.

Hello.
I have big problem with my mobo. I can't run 645Ultra mobo (MSI 6547) with other memory than installed actually. Now I have Samsung DDR333 128MB (one-sided), and everything works well. But I tried to install another modules (2 pieces - 256MB DDR266 double-sided). After install one of those modules, my comp doesn't start. Mobo only beeps and there has no signal on my monitor. With installed two modules - my memory (ddr333) and one of those 256MB ddr266, computer runs, but POST shows me only 128MB :(.
What is going on? Does this mobo supports memory other than ddr333 (user manual says - YES, but now I'm not sure).

"645 ultra" DDR Brands tested with this board
http://www.msi.com.tw/html/support/testreport/6547/memory.htm
ddr 333 what brand :O
ddr 266 what brand :O
DDR 266 aka 2100 Cant run at 333 aka 2700 ;(

MSI NEO2 Platinum, problem with mouse Genius PS2 optical

Hello,
I have a MSI NEO2 Platinum motherboard with a mouse Genius optical PS2. When the S.O. init the mouse is not detected, I unplug and plug again the PS2 port and the mouse work perfectly ! ... The mouse is working perfectly, I test it in another PC, the problem is the motherboard !
The same situation is on Windows XP Professional and Linux Ubuntu 5.10.
Please help me, thanks for your attention !
Raúl.

Raúl,
The PS2 slot is NOT a hot plug! If you remove and reinstall it while there is power to the mobo you stand a very good chance of destroying the PS2 Slot.
Take Care,
Richard

[Solved] MSI GT60, Major Problem With Updating

Hi everyone, I've owned a GT60 since about January and I've had a few more minor problems so far, but now a rather annoying one.
I cannot update anything it seems, I've got numerous messages to install 8.1 for free, despite having downloaded and installed it a few times. When I download and install it no changes are made but it says the install happened and was successful. I now have this problem with a new version of Java, it asks me if the program can make changes to my computer once every session, even though I've downloaded it and clicked yes a few times.
On a side note, just today my audio stopped working. When I plug in headphones the audio comes in but all crackly. I uninstalled the drivers and reinstalled them, still wont work.
Thanks for any help

Quote from: Niloc;104288
Can you be more specific with which upgrades I've installed, do you mean windows updates or every single update for anything ever installed? What do you mean by run the windows 8.1 upgrade from market? If you mean did I download from there and then hit run when the little pop up comes on screen, then I did that. If I restore the system, will i lose anything? I'll give those instructions a try then. I should also have mentioned that everything was installing properly, until the update was released and I tried to install it. It never worked and then Java was giving me problems, and I had the audio problem, so I finally decided it was time to ask for some help lol.
About the audio, I only get the crackling from my headphones, the speaker is dead silent. Its also not just pure crackling, like songs sound mostly normal and understandable but with some crackling. I found that if I turn my volume just a few clicks up from being mute, there's no crackling. Its almost as if my volume is too loud at a normal volume and its blowing the speakers.
Thanks for the info
If you do a system restore, the system will be back to the factory settings which mean yes, you're personal data and self-install programs will be deleted.
*Make sure you backup all your personal data!
You can use F3 function to do the system restore and do the update after.
(Power on the notebook and press F3 after MSI logo shows up, and follow the instruction for the system recovery)
1.Execute MSI BurnRecovery Tool to create Windows 8 recovery discs.
2.Back up all personal files
3.Uninstall both NVIDIA and Intel VGA driver.
4.Uninstall touchpad driver.
5.Run Microsoft Windows Update. (Press WIN>search windows update>check for updates) *Make sure you install all important and optional updates.
6.Restart you notebook.
7.Check again if there is any available updates in Windows Update and do restart after the installation. (Repeat the updates till you don't see any updates available.)
8.Press WIN key and choose Market.(You should see the big "Update to Windows 8.1 for free" button and click it to start the update.)
9. System reboot after finishing the update
10. Go to MSI website and download+install the latest drivers.(including vga drivers and touchpad driver..etc)
For the audio: Try to uninstall the audio driver and reboot the system and see if the speakers work without Realtek audio driver.

MSI P45-C51 (Problems With 4GB DDR3 1333)

Hello,
I have a problem with my motherboard P45-C51.
According to test reports, this motherboard supports 4GB DDR3 modules (1333).
msi.com/file/test_report/TR10_1836.pdf
Data specifically are:
Model: Kingston KVR1333D3N9/4G
Size: 4GB
2 DIMMs: V
4 DIMMs: V
R.S.T: OK
In the absence of stock the store, I bought a similar one:
Fury HiperX DDR 3 1333 (HX313C9F/4)
however, the motherboard does not recognize the memory (when I turn on the computer, 3 beeps sound and restarts, return to ring 3 times and then restarts and so on)
With 2 GB DDR3 1333 DIMM working properly.
I have last Bios v5.7
I found an online store the specified memory for my motherboard (Kingston KVR1333D3N9/4G) but want to be 100% sure it worked properly before buying.
Thnks.

hi,
With Fury HiperX DDR 3 1333 (HX313C9F / 4) i deleted the CMOS but I did not recognize. After much searching, I concluded that the problem could come from the distribution of the chips.
The Kingston (Fury HiperX DDR3 - 1333 - HX313C9F/4) memory have 512Mbx8 Chips (single-sided)
The G.Skill Ripjaws (F3-10666CL7D-8GBRH) memory have 256Mbx16 Chips (in two sided)
With G.Skill The mbo detect the memory and boot normally. No necesary delete CMOS.
The only problem is latency, latency detects and configures it is nine. However, changing the latency in the BIOS manually to seven working properly.
Thnks.

MSI GF615M-P33 problem with sb audigy se

Similar Messages

Maybe you are looking for