MSI GNB Max (MS-6565): insufficient voltage

I have just installed my new GNB Max, and got XP Pro up and running. Upon installing PC Alert 4, I recieved a warning that the +3.3V was actually sub 3V(2.9+V). What effect will this have? And what kind of Variance should I tolerate?
Many thanks.

My GNB Max + Antec true power 430 read 3.33.
Sounds like a power supply not handling the load.
Acceptable tolerance in the PC industry is +-5% (3.135 is therfor the lower limit)

Similar Messages

  • MSI GNB MAX and RICOH R5C476II PCI to Cardbus bridge not working! Help

    Why my PCMCIA & CARDBUS Card Reader based on RICOH R5C476II Chipset not
    working on MSI GNB MAX BOARD (with newer bios 2.3)???
    My Card reader is fine and working properly on many ithers motherboards like: ABIT BD7-II based
    on Intel 845E Chipset, or ASUS TUSIM, ASUS TUSL, and ASUS PIIIB-F
    Why ??
    Please help me.

    Yes, sure. I'm trying to use all of five PCI slots, and after slot chnge I,m setting Reset Configuration data in BIOS.
    result is the same in all Card positions. Card is detected, but not working corectly.
    I'm trying to resolve any hardware conflicts by disabling all od internal mothebrord components like IEE1394 Audio, Serial Ata and others - no cahnges, no solutions ....

  • Realisticly:how much OC with my system?MSI GNB MAX

    Ok, How much OC I can get, with my system, if I change the 1.5ghz 266DDR Value RAM to something better. Any suggestions.
    I plan to ditch the ram for something better, but my mobo, and CPU aren't that fast compared to the C, and E, and the 64 stuff.
    I am using the 2.8B, E7205/i7205 mobo.
    Only fan cooling. Using the pipe101, will place the tornado on it. Does the vantec fan card improves my GF performance.
    I am just able to OC my card from 350 to 388mhz, 1.09ghz, others got a 420mhz on a supperior system. All using the inno3d 6800gt.. Or I'm looking at an "old" system already.
    The OC FSB is just up to 153. I read somewhere that it is useless/not worth to OC this system.
    So what do you think?
    my system is in the signature

    I would not push further than 160 FSB, you can corrupt your disks since PCI /AGP are not locked. Usually PCI frequency above 38 MHZ is not considered safe and 150 FSB corresponds to 37.5 MHZ PCI frequency. I corrupted my 30 GB WD at 160 FSB.
    I have GNB Max, P4 3.06HT, 2x 512MB KVR DDR333 (CAS2.5 rated). I oveclocked the system to 150 FSB,  P4 is running as 3.45GHz@600FSB (HT is on), with dual channel DDR300 memory (2-3-3-6 timings). System is 100% stable after testing with Linux kernel compile, Prime 95, 3DMark benchmarks. The performance gain in CPU intensive benchmarks is almost the same as increase in FSB frequency, which is 12.5%, since RAM overclocks in sync with CPU.
    If you settle at 150 FSB, your DDR266 will be running as DDR300. You can test it with its given SPD values and if not stable you can reduce CAS setting one step, i.e. from CAS2.5 to CAS3. If none of these are possible, you can upgrade with DDR400.
    I use Vantec Fan card with my GF4, but it did not help me increase my overclock. However, I removed the fan on my GF4 (heat sink is not removed just the fan) after trying to increase the overclock. Vantec Fan card is much more silent compared to the Thermaltake fan and copper heat sink combo. I still can overclock as before but do not need to put up with the noise of Thermaltake fan.  
    Hope this helps
    My Config:
    MSI GNB Max FISR
    P4 3.06 HT (SL6PG) (oc 3.45@600)
    2X KVR DDR333 CAS2.5 (running as DDR300 2-3-3-6 timings)
    Compro Personal Cinema GF4-Ti4200 64MB (oc 285/570)
    SB Live!
    DLink 802.11b wireless PCI
    Seagate 80GB EIDE (Windows XP SP2)
    WD 30GB EIDE (Slackware Linux current)
    NEC 4X DVDR/RW
    Sony 16X DVDROM
    etc

  • GNB Max MS-6565 and Dual Channel DDR ram

    What's the deal with this new type of memory?
    I can only find bits and pieces of information from online retail stores and I am bit frustrated.
    Does anyone know where I can find more information?
    Cheers

    Quote
    Originally posted by vaporas
    I visited the forum. Thanks for the tip. :-)
    Ok, you said that the MSI board cannot be overclocked. Fair enough, I guess you have tried it yourself.
    If you increase the fsb speed to 170MHz, why not decrease the multiplier?
    170MHz * 14 = 2.4 (2.38)
    instead of,
    170MHz * 18 = 3.06
    Also, do you know whether the mainboards that you mentioned (by Asus and Gigabyte) will allow me to increase the fsb speed to 200MHz?
    vaporas
    The multiplyer cant be changed on the P4's, unless u have an engineering sample, and theres no way we [general public] could get one. Plus raising the FSB on the MSI board IS the problem, it scales the AGP/PCI with it, and doesnt allow u to increase the voltage for AGP and Mem. With the FSB on the asus and gigabyte, it'll be more CPU limited untill you get to about 210MHz, but I think you should be able to easily clear 170 FSB, if not 180FSB before anything becomes limiting...

  • Can this ram work on i7205 MSI GNB MAX?

    http://www.twinmos.com/dram/dram_p_sp_ddr400.htm
    Can I use that RAM on my mobo. The mobo is 2.5v max I think.

    it might work but would only run at pc 2100 speeds
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=387
    • Support Dual channel DDR266 memory interface. Each channel supports 2 DIMM Sockets.
    • Support four 184-pin DDR DIMM sockets up to 4GB.
    • Support non-ECC(x64) or ECC(x72) DIMMs DDR PC2001 DIMM using 128Mb, 256Mb,
      512Mb and 1GB SDRAM

  • Gnb Max Ms-6565 & Usb

    Need some imput on the front USB2 connecters. The user guide says "2".
    Now I know one is on side of board ( JUSB1) but I'm not sure of the other
    one. Is (JDB1) the other one ? Its where you plug in the D-BRACKET.
    I have more use for it as a USB connection than the D-Bracket.
    Thanks
    Jutias

    JUSB1 has pins for connecting two USB ports. Page 2-28 in the manual shows the pinout. See the link in Wonkanoby's signature for info on a jumper you may have to remove.
    You can get a copy of the manual at http://www.msi.com.tw/program/support/manual/mnu/spt_mnu_detail.php?UID=387&kind=1

  • Anybody have ANY ideas? MSI GNB MAX FISR

    Does anybody have any knowledge of when MSI's next updated BIOS will be with the AGP/PCI frequancy selector and AGP/PCI Lock will be bought out? I look forward with anticipation! Anybody have release dates atall?

    aint that just stupid?,
    would it cost them more to make it with agppci lock?
    If it was with that i would have bought it  8)

  • MSI GNB MAX-FISR agp/pci lock

    Does it have agp/pci lock ?
    -Cheers, ScadamiCa

    aint that just stupid?,
    would it cost them more to make it with agppci lock?
    If it was with that i would have bought it  8)

  • MSI GNB Max and P4 3.06 with 56C Idle (Bios)

    is that ok or to high, i know about some bugs with the Temp Sensor so there are my 2 cents ! :D
    Please give me some feedback thx. !

    I had the exact same problem.  I bought a Cooler Master IHC-H71 CPU cooler and it brought me down to 40-44 at idle.  Ordered it from http://www.phamcomputer.com

  • Anyone got "GOOD" sound out of GNB-Max 6565?

    Hello,
    I'm getting a very lousy sound out of my 6565.  I tried all options such as with or without the S connector, 2, 4, and 6 channels, all possible inputs, different hardaware acceleration levels, etc.
    The sound output is bad, and the microphone doesn't detect anything.  I've noticed that many people were having the same problem.  Does this mean that this MB requires a special speaker system?  Can't I use two speakers like old times and get stereo sound out of them without any software/hardware tweaks?
    Thanks for any help?
    Maria
    MSI GNB Max-FISR 6565-010
    CT6472Z265.18T: 1024MB 184-PIN DIMM 64Mx72 DDR PC2100
    Intel Pentium 4 Processor 2.5GHz, 400MHz FSB, Socket 478
    XTASY Everything
    Windows XP Professional
    Two legacy speakers

    I have the same board but I didn't even try onboard sound.  My experience with onboard sound on other boards has made me just start with a good pci sound card (sound blaster audigy).  Every onboard sound I have tried either sounded bad or worse.  If the board had a creative chip on it you may get medium quality.  Don't waste money on new speakers to use with the onboard sound, spend the money on a soundcard.  Of coarse if money is not an issue you could buy both.

  • GNB Max temps and worries

    Okies, I have a question / problem... maybe?
    My MB, after being turned off for 30 minutes, on bootup, going DIRECTLY into the Bios, shows, under PC Health, a temp of 51C and climbs to 57..varying to..58.
    Now I have the 3.06 GHZ Intel chip.
    (No, I really don't care about anyone else's temp if they are overclocking or using something like a 2.4)
    No overclocking anything.
    Bios 2.2 and I did as Asaaf suggested and changed the thingys to 134 and 1.525.
    I have an Alpha PAL8942 - which is supposed to be a decent heatsink on the P4.
    IS THIS NORMAL / USUAL or not? If not, then should I take the sink off and re-apply the Artic Silver and try for "better"?
    Oh, and MB temp is at 41C. - But I didn't mess with tha because the fan came on the MB attached.
    Thank you in advance for your response.

    Quote
    Originally posted by scorpes
    I have a p4 3,06 ghz with standaard P4 cooler and GNB MAX with a total of 6 fans and my normal cpu temp is: 54c  and system temp is 35c, and mine cpufan speed is around 3700 rpm (says pcalert)
    but if i play a game such as unreal 2003, my cpu is getting very hot: between 80c/85c and my vcore is 1,4
    AND MSI SAYS IT'S NORMAL THAT THE TEMPERATURE IS THIS HIGH?
    (http://www.msi.com.tw/program/e_service/forum/viewindex.php?threadid=13840&boardid=10&styleid=1)
    MSI GNB MAX (ms-6565) motherboard
    P4 3,06 ghz processor with standaard p4 cooler
    1024 mb DDR 266 mhz (dual) memory
    Geforce 4 mx videocard
    60Gb Maxtor ATA133 HD
    Promedium Mars case with a total of 6 fans
    I have had the same problems. The cpu temperature was about 52c when the using was idle.
    When the using was more then 80% the temperature was rising in some secons over the 75c.,after replace the cooler there where no more problems. He was not realy good placed on the cpu
    Now the temperature is between 46c and 52c.
    MSI GNB MAX (ms-6565) motherboard
    P4 3,06 ghz processor with standaard p4 cooler
    2x512 mb DDR 266 mhz (dual) memory
    MSIGeforce 4 ti4800SE
    80Gb Maxtor ATA133 HD
    60Gb Seagate Baracuda ATA100

  • Very high temp. with GNB MAX

    Hello, i have a problem with my MSI GNB MAX motherboard and my p4 3,06 ghz
    My cpu temperatures are very high, with a maximum of 85/86c,,, is this normal??
    Anyone else having a similar problem like this?
    MSI GNB MAX (ms-6565) motherboard
    P4 3,06 ghz  processor with standaard p4 cooler
    1024 mb DDR 266 mhz (dual) memory
    Geforce 4 mx videocard
    60Gb Maxtor ATA133 HD
    Promedium Mars case with a total of 6 fans
    (not overclocked)

    If Vcor is 1.4 (I'm running 1.525 but reads 1.47 in PCAlert), AND fsb is set for 134, AND your HSF is running AND has good contact, there is no way for it to be that hot. The stock HSF is a pretty good part. I would suggest getting a temperature probe and touching it to the base edge of the HSF to see if you are really that hot. In Bios, I have the cut off threshold at 65C and alarm at 63C. I dont know the exact conversion but 86C is near hot enough to boil water. The laquer from the chip would probably begin to melt and create an odor.

  • MSI GNB FISR 6565-010

    I just ordered all of my parts to build my new work station.
    I am getting a little confused with the DDR situation. Many of the reports on the MB that I have read used the PC2700 ...333Mhz DDr's. Are the boards still only approved to run PC1600's and PC2100's?? What can I expect if I use PC2700's?? I was going to install some high quality OCZ's that were matched....4...256's PC2700.
     Also the latest Deluxe version of the board should be coming with ATA 133 and FireWire also??
     I am all ears...please send advice.Thanks
    Bill Vesia
    New station
    MSI...GNB-MAx-Fisr-6565-010
    2.8 Pentium 4 with Hyper Thread
    120 Maxtor ATA 133
    MSI Ti4200 VTD8X 128MB

    At the present time I am running 2 sticks of 2700 and the mem scores are well let me see if Ican simply post them here.
    SiSoftware Sandra
    Int Buffered iSSE2 (Integer STREAM) Results Breakdown
    Assignment : 3774MB/s
    Scaling : 3760MB/s
    Addition : 3965MB/s
    Triad : 3950MB/s
    Data Item Size : 16-bytes
    Buffering Used : Yes
    Offset Displacement Used : Yes
    Bandwidth Efficiency : 76% (estimated)
    Float Buffered iSSE2 (Float STREAM) Results Breakdown
    Assignment : 3777MB/s
    Scaling : 3766MB/s
    Addition : 3970MB/s
    Triad : 3953MB/s
    Data Item Size : 16-bytes
    Buffering Used : Yes
    Offset Displacement Used : Yes
    Bandwidth Efficiency : 76% (estimated)
    Test Status
    Memory Used by Test : 512MB
    SMP Test : No
    Total Test Threads : 1
    SMT Test : No
    Dynamic MP/MT Load Balance : No
    Processor Affinity : No
    Chipset
    Model : Intel Corporation E7205 Host Controller
    Front Side Bus Speed : 4x 158MHz (632MHz data rate)
    Max. Bus Bandwidth : 5056MB/s (estimated)
    Logical/Chipset Memory Banks
    Bank 0 Setting : 512MB DDR-SDRAM 2.0-3-3CL 2CMD
    Bank 1 Setting : 512MB DDR-SDRAM 2.0-3-3CL 2CMD
    Channels : 2
    Memory Bus Speed : 2x 158MHz (316MHz data rate)
    Max. Memory Bandwidth : 5056MB/s (estimated)
    Features
    MMX Technology : Yes
    SSE Technology : Yes
    SSE2 Technology : Yes
    HTT - Hyper-Threading Technology : No
    As you can see i am running just below the 4gig mark on bandwidth.  I stuck some 3500s in dual channel set (got a deal and I am waiting to see whether I need to buy another board to use) and the results did not change.  So i would say that you should go with 2700 so as to give yourself plenty of headroom on the ocing.

  • Gnb max make me crazy !! bug report

    Please help!
    I had before abit bd7II 845e mobo with p4 [email protected] ghz
    And audigy2 platinum soundcard and bluetooth dongle. 2*256mb ddr400 ram.
    My p4 1.8 ghz worked fine with 1.5v 133mhz@2400mhz in my abit mobo.I work with this computer half year without any problem.
    I bought the "new, fast..." msi gnb max with bluetooth,thinking how fast the double ram control,and the onboard bluetooth better than my usb dongle.
    My problems:
    1.:
    when i in bios set up fsb 133mhz then work all,but just 100 mhz : my p4 go 1.8ghz
    when i in bios set 160 mhz then ~120 mhz
    And once more can i set 178 mhz once not,than go the fsb 133 mhz and my p4 2.4 ghz, but when i restart my system than again work with 100 mhz. This game make me CRAZY!!!!
    When i set up in bios the fsb to 133mhz then why not work correctly 133mhz, why 100 mhz?????????????
    Thats the stupiest think what i saw in my life!!!
    2.:
    My audigy2 card what before in my abit mobo work perfect,this mobo once go infrared remote control, once not, i don´t know why!!!!!!!!
    3.:Bluetooth once work perfect,once not and i don´t know why !!!!!!!!! (It seems all right but just when i would like send program to my nokia,or activesync with my ipaq the say error with services)
    4.: I make test with msi fuzzylogic 4 to overclock my mobo. work great but this program is buggy. When i close than mak acces violation error.
    I tried with higher voltage too,but in bios and via fuzzylogic not worked perfect too.
    My mobo came from factory with bios 2.2, what i heard little bit buggy,later i flash bios 2.1 and try too.... wothout result.
    I need help,i need support!!!!!
    I SPEND 240€~240$ for this mobo,
    I´M NOT BETA TESTER !!!!!!!!!!!!!!!!!
    When msi not solve these problems next week then i give back this mobo to shop,and nomore buy another msi board.
    From januar 10 (bios 2.2) msi know  this bios buggy and 2 month later no update!!!!!!!
     X(  X(  X(  X(

    Please help!
    I had before abit bd7II 845e mobo with p4 [email protected] ghz
    And audigy2 platinum soundcard and bluetooth dongle. 2*256mb ddr400 ram.
    My p4 1.8 ghz worked fine with 1.5v 133mhz@2400mhz in my abit mobo.I work with this computer half year without any problem.
    I bought the "new, fast..." msi gnb max with bluetooth,thinking how fast the double ram control,and the onboard bluetooth better than my usb dongle.
    My problems:
    1.:
    when i in bios set up fsb 133mhz then work all,but just 100 mhz : my p4 go 1.8ghz
    when i in bios set 160 mhz then ~120 mhz
    And once more can i set 178 mhz once not,than go the fsb 133 mhz and my p4 2.4 ghz, but when i restart my system than again work with 100 mhz. This game make me CRAZY!!!!
    When i set up in bios the fsb to 133mhz then why not work correctly 133mhz, why 100 mhz?????????????
    Thats the stupiest think what i saw in my life!!!
    2.:
    My audigy2 card what before in my abit mobo work perfect,this mobo once go infrared remote control, once not, i don´t know why!!!!!!!!
    3.:Bluetooth once work perfect,once not and i don´t know why !!!!!!!!! (It seems all right but just when i would like send program to my nokia,or activesync with my ipaq the say error with services)
    4.: I make test with msi fuzzylogic 4 to overclock my mobo. work great but this program is buggy. When i close than mak acces violation error.
    I tried with higher voltage too,but in bios and via fuzzylogic not worked perfect too.
    My mobo came from factory with bios 2.2, what i heard little bit buggy,later i flash bios 2.1 and try too.... wothout result.
    I need help,i need support!!!!!
    I SPEND 240€~240$ for this mobo,
    I´M NOT BETA TESTER !!!!!!!!!!!!!!!!!
    When msi not solve these problems next week then i give back this mobo to shop,and nomore buy another msi board.
    From januar 10 (bios 2.2) msi know  this bios buggy and 2 month later no update!!!!!!!
     X(  X(  X(  X(

  • GNB Max-FISR and VCORE

    Mt CPU Core Voltage is showing up as 1.42-1.44 in
    the Bios & MBM.
    Is this a problem?? Should I change it to !.5 or so in
    the bios??
    The board has Bios 2.2 in it......
    CPU temp 50 deg Cel.
    Thanks
    Mike

    Thanks ASSAF for the reply. If 1.42-1.44 is ok I'll
    just leave it alone for now....untill CPU and MB ard
    broke in.
    My GNB Max-FISR is stable . I really like this board.
    Thanks
    Here's my setup .
    Intel P4 2.53/533 c1
    MSI GNB Max-FISR
    2x256 PC2100 Kingmax
    MSI GF4 TI4600 WD 80Gig/7200 8MB
    Antec 500W Yamaha CDW-FIE
    Creative 52X CD-ROM
    SB Audigy
    Promise Ultra 133 TX2
    WME

Maybe you are looking for