Msi gt780 illuminated keyboard software and RAM problem

hi i just bought a new msi gt780 i5 version how come there was no software included to alllow me to change the colors of the l.e.d lights and i did not receive the msi afterburner
and is it true the i5 version cant go over 8 gig of ram?

Quote from: derich on 06-July-11, 22:06:04
hi i just bought a new msi gt780 i5 version how come there was no software included to alllow me to change the colors of the l.e.d lights and i did not receive the msi afterburner
and is it true the i5 version cant go over 8 gig of ram?
you can find all utilities for your notebook, from msi web page:
http://www.msi.com/product/nb/GT780.html#/?div=Utility&os=All

Similar Messages

MSI GT780 DX Adding SSD and Recovery Problem

I right now have 750 GB Sata in my Laptop i recently purchased 240 GB SSD (Corsair)
Now my problem is
i want to recover the factory settings to SSD i mean i want to recover and install windows 7 with all pre installed drivers to SSD by keeping the recovery image in 750 GB Sata
is there any way please suggest and help me as i do not want to loose the image which came with laptop and the laptop is very new brought 1 month back
Please suggest me solutions for my problem

Hi,
Have you proved by using Win7 backup located in Control Panel?
If this tool doesn't work, then look at this tool:
http://www.apricorn.com/products/notebook-hard-drive-upgrade-kits/ez-upgrade-universal-hard-drive-upgrade-kit.html?type=reg&id=1023
Hope this helps.

HT201413 i cannot restore my ipad software i had download a new software on itunes but i couldnot download it on ipad or restore the old software and the problem is restoring ipad firmware

i cannot restore my ipad software i had download a new software on itunes but i couldnot download it on ipad or restore the old software and the problem is restoring ipad firmware

Try and force iPad into Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.

Windows 7 software, and password problems

A friend got a new computer (old had had 30 gb drive, 256 mb Ram, and viruses). So I helped hime pick up a new laptop (Windows 7 home premium), etc, and am helping him get everything set up. He has a Linksys wireless router wrt54g V8. He was able to connect immediately to the network as there was no security on it (it said unsecured)...his neighbors had secured networks, he did not. I said that this needed to be fixed. He had the origional cd (bought 11\07), so I tried to install the software on Windows 7. It would not install (wrong operating system\whatever). In my very limited knowldge of routers (set up mine a few years ago), I remembered that there was an ipaddress 192.168.1.1 where some things could be changed. We did get to the wireless tab, and there was a 'reset' button on it. I thought that this would be where we would be able to change it from unsecured to secured...apparently I was wrong. By clicking that button, his network disappeared from the list of networks. There is a new linksys... network in the list now. Anyway, I got him going again hard wired to the comcast router. How to correct this situation, I have a number of questions? Does this router work on windows 7, and where is the software to download and how to execute it (I did find a .bin file on line, but have no idea of how to execute it, if everything I need is in it, and if it is applicable to windows 7). OK, if I do not need to install anything on the new system, how do I recreate the wireless connection to the wireless router with a secured connection? How do I create a new network (or recover the old one) and secure it without software, and some kind of password (which he does not know)? Thanks.

What is the Model no of the Router...?
As you pressed the reset button on the router..You need to configure the router from scratch.And the router does works on Windows7.
As your ISP is Cable,follow the steps given here to configure the router.

MSI GT780 DXR keyboard problem

hello,
i've got a problem with my keyboard its like i cant press W,E and space in the same time...so genarly in games such as world of warcraft i cant move forward and starf right and jump in the same time...while i can if im starfing left side...no matter what i do i cant press those 3 buttons at the same time in all games...altho when i connect a USB keyboard to the laptop i can do that without any problem...is there an driver update to fix this problem or any way i can get it fix please help me guys and thanks.

Quote from: Tiradus on 26-December-11, 23:02:55
Hi Everybody,
I'm experiencing the same problem.
Is there anything to do to solve this problem ?
Thank you by advance and I wish you season's greetings.
Tiradus
hey mate,
sorry to tell u that there is no solution for this problem they said its a gaming laptop with a gaming keyboard !!
im sorry to said that a bullshit, now im useing an USB keyboard for gaming insted of useing the one in the laptop...

Z77GD-80 Boot and RAM Problems ( caused by ME Flash Fail )

Hi everyone , i recentlty updated my MB to Bios Version 1.2 and noticed that an option had been added => update bios and ME
tried that option , chosen the same bios file ( 1.2 ) , a warning popup came up that mentioned to not unplug or shutdown the system , the flashing went well until it decided to flash the "ME".
the device rebooted after the the flashing reached 100% ( i think that was when the BIOS flash ended ) ,another flashing started after the Reboot but it did not complete and rebooted @ 60%( ME flash ? ) ! since then i cannot boot using that Bios , the debugger keeps showing error 15 and 19 , going from one to another rapidly .
tried to boot using the second bios ( bios switch ) it did boot fine , but only detects half of my RAM ( 8 G ) tried each MB DIMM and Module separately and all worked fine !
tried to flash the first bios via booting from the second but that didn't work from bios ( strange thing was that when i saved the second bios in USB it was only 6Mb and would not be detected to flash , but my downloaded bios are 8Mb and were available to chose for update )
1-if i try to only flash the bios it restart @ 100 % but then the same debugger error appears after reboot
2-if i try the BIOS and ME , same thing happens it restart @ 60% and the debugger error appears
tried AMI bios flasher for windows , and it did flash the BIOS just fine but when it tries the ME , it keeps erroring that this Bios doesn't support this function
so i had 2 question in mind
1- How can i flash the ME to solve my problems ?
2- why is half of my ram not detected in the second Bios ?
any help would be appreciated
thansk

>>Use the MSI HQ Forum USB flasher<<
Use the forum flash tool to prepare a usb stick for flashing. Download the attached bios to your desktop and use option 1 of the tool, point the tool at the entire archive. After the flash (It will flash the me as well) do a full cmos clear with the cord removed.
Then re-install the ME drivers inside windows.
In regards to the non working bios, first try a full cmos clear, if that fails:
https://forum-en.msi.com/index.php?topic=160450.0

MSI GT780 - Backlit keyboard in most countries not available?

I would like to know why doesn't my country (Portugal), as well as many others, allow or sell any MSi's gaming series laptop WITH the LED back-lit keyboard.
I was a click away of ordering my own MSI GT780DXR-403PT (that's its name, in my country), when I noticed something that said, roughly translated, that the so-called back-lit keyboard wasn't really back-lit. So what I did was I called them (the seller) and asked them why didn't they sell the laptop with a back-lit keyboard.
They replied that MSi didn't ship any laptop with it, and what's even more curious is that, even though there are no LED's, the button to light them on AND the software to change the colors is loaded on the machine.
So, that said, I'd really like to know if and how can I buy a GT780DXR with a BACK-LIT Portuguese keyboard?
Thank you so much, and if this is a repost of some other guy, I'm sorry... I did try to search for a question like this, but nothing popped up.

Not sure why you're mentioning the UK since I clearly stated I'm from Portugal, but whatever. Also, thanks for the replies, but I'd really like to buy a keyboard with a >>Portuguese<< layout and with the back-lit keys.
This is so unfair, since the laptops are the same price as a back-lit one... MSi should really look into this, I mean, either lower the price since there are no lights, or get the freakin' lights on the machine.

MSI Z87-G65 Gaming BIOS causing RAM problem?

Hey
I updated my bios something like week ago from 1.7 to 1.8 and seems like it is causing ram to behave oddly. I installed the BIOS via live update 5 and flashed the computer via USB. Seems like the ram usage climbs to 100% at span of few hours, usually something like 2-4h. Also my SSD usage also is very high at the same time, around 50-100% changing rapidly. Haven't had the problem at earlier bios versions. Also task manager won't show any specific process that is using all that RAM/disc. Kinda annoying that can't use computer longer that that because it gets so laggy :(. I'll include some screenshots from task manager.
Thank you!
System specs:
MSI z87-G65 Gaming
Corsair Vengeance pro (2x8GB) 1866MHz C9
Intel i7-4470K
MSI Geforce GTX760 Gaming
PSU Corsair AX760

Quote from: Sea Dog on 31-December-13, 04:01:00
After the flash, was a PSU power cord removed, battery removed CMOS clear performed? Also, was the ME driver re-installed with the latest available? If none of that helps, then I would suggest to contact MSI Technical about the problems encountered with the new UEFI/BIOS revision. A reflash can be accomplished as well back to a version that was working. There is no real need to keep updating a UEFI/BIOS if all works without any problems with the exception of a specific improvement of a particular function that may have been less than optimal.
No I didn't, I'll try it that way and check out if it works. Tough ME driver is a latest but I didn't re-install it.
Thanks for response!

MSi z87-gd65 OC Genie and RAM frequency issues

Hey all,
I just built a new computer (my first build), and am quite glad with the capabilities of the machine. However, whenever I try to turn on OC Genie or bump up my ram speed to 2400 MHz(I believe this is the native speed, but the motherboard puts it down to 1333MHz) the system fails to boot, and sometimes hangs in a rebooting cycle. Eventually, the motherboard gives an error on the screen saying that the changes made have failed and was restored to default settings, and to press f1 or f2.
I admit I am a complete novice at overclocking, and probably do not know what I did wrong. I've updated the bios, cleared cmos, and tried both bios A and B, but have got the same results. I was hoping I could get some help on this forum and learn new workarounds! Any help is greatly appreciated.
My Build:
i7-4770k @ stock frequency
MSi z87-gd65
Corsair H100i
SeaSonic Platinum SS-860XP2 860W 80 Plus Platinum Certified
Samsung 840 Evo SSD 256 gb
Corsair Vengeance Pro 2400MHz CMY16GX3M2A2400C11R

Quote from: phantom24 on 19-October-13, 08:56:19
Hey man, thanks for replying. The first thing I tried, before overclocking, was to enable XMP from the UFEI. When i enabled it, the board would show that memory was OC'd to 2400MHz and bumped up to 1.65 voltage. This is all shown prior to rebooting. When I would reboot the computer however, the system would fail to boot and I would get the same error saying all "overclocking failed, reset to default settings". I believe that my ram is the cause for my inability to overclock. I found out that motherboard is not compatible with it at extreme speeds. The max speed I can get out of my ram is 2133MHz with no problem whatsoever in rebooting. This is without changing the voltage of the ram( keeping it at 1.5v) . If I change the ram voltage, I'm pretty sure it would fail to boot.
Yeah good luck with OCing and please let me know if you find anything useful. I'm afraid that this forum does not have much to offer, so you may want to try some other forums.
Jms and Xfx are right. By default mine booted to at 1600mhz. I enabled XMP and it brought it to the rated speed of 2133mhz. I'm not trying to overclock my ram further than the rated speed. Pointless to me, considering I'm coming from a rig that had ddr2 with 800mhz. As you can see in my pic, the one with blue LEDs is the 7.5 year old build. Still going strong. Anyhow, if you do overclock, make sure you disable the XMP. That way you can eliminate another possible instability issue. I'm a member of a few forums, and I was suprised to see these forums not respond very well. For the guys who did respond, I thank you! You may also want to check out overclock.net There's are plenty of people there and "clubs" you can be a part of. I'm finding a lot of useful information there. Most people won't get mad about noob questions unless you do like me and ask the same ones in multiple threads lol! Hop on over there and check it out. My name there is Scotty Mac.

White MB early 2009 and RAM - problems?

Hello,
anyone has any experiences with RAM upgrades for the new NVidia white? I bought some 'quality' RAM (4 Gig kit, Mac memory, DDR2, 667MHz, PC2-5300, CL4) but they only cause trouble .... ran memtest 4.21 and lots of errors occur.
So, is that a problem with compatibility with the NVidia MacBook or are the sticks erratic?
Anyone having any experiences with Corsair Ram or comparable?
thanks
Steff

Thanks for your reply ...
Your Macbook requires SO-DIMMs) of 667MHz DDR2 SDRAM, use ram that meets that spec and you'll be fine.>>
I had that ... 5300 DDR2, 667MHz, CL4 .... so it is not the whole thing .... On that site there is just the normal blahblah, nothing specific .... Bought that computer (decided for it), so I know the standard blahblah ....
I think that once you have some decent ram from a decent vendor that meets Apple's specs you'll not wish to go back to windows! >>
I have been a Mac user since I left the Atari ... so it would definitely not be 'going back to Windows' ....
dump the v4 beta. Use the current version 3.2.3 and I think you'll have no problems.>>
Maybe ... but if a beta software does not even work with the stuff of the developer ....
thanks
best
Message was edited by: steff3

T500 TurboMemory , Volume and RAM problems

Recently I found some problems with my T500.
1.Everytime when I restart the computer , the harddisk led will keep illuminating for about 5~7minutes. I checked "TaskManager -Resource Monitor -Disk" found "\Device\HarddiskVolume1\ReadyBoost.sfcache" was writing in high speed. Is it normal?
2.Everytime when I restart the computer, the volume was set to 50db, whatever I set before the restart, it will go back to 50, even set to mute.... Why?
3.I updated the RAM to 3G(1 2G single and 1 1G singal), from my computer I can see it says 3G memory, But in TaskManager only 2.5G can be used. 32bit Vista-B ATI 3650 graphic card.....why?

I dont know about the 2nd problem you have mentioned here but as for the first one I guess that's a little bit unsual. It shouldn't be busy more than 2-3 mins unless you have lots of programms to load.
As for the last problem you should be able to see 3GB installed I guess but I am not sure if you can use it since you have vista 32. I know that you definately will have problems with 4GB but not sure about 3GB.
=================================================================
Lenovo T500 - T9400 2.53 GHz - 2GB PC3-8500 1066 MHz - ATI Radeon HD 3650 256 MB - WXGA W/LED - 160 GB 7200 RPM - 2GB Turbo Memory
=================================================================

Keyboard events and scenes problem

I have 2 scenes. In both scenes, I have a movie clip that moves via keyboard control. If the goto next scene is triggered by the movie clip in the first scene the keyboard control works in the second. However, if I use a button to move to the next scene then there isn't any control over the movieclip in that scene. I've traced the keyCode in the second scene and it is picked up but the switch statement doesn't run. I'm migrating to Actionscript 3.0 and updating something I created in 2.0. I would like to do it without writing a class.
Scene 1 code:
stop();
stage.addEventListener(KeyboardEvent.KEY_DOWN, doKeyDown);
function doKeyDown(e:KeyboardEvent):void {
switch (e.keyCode) {
case Keyboard.LEFT :
   b1_mc.x-=5;
   break;
case Keyboard.RIGHT :
   b1_mc.x+=5;
   if (b1_mc.x>350) {
    stage.removeEventListener(KeyboardEvent.KEY_DOWN,doKeyDown);
    gotoAndPlay(1,"Scene 2");
   break;
next_btn.addEventListener(MouseEvent.CLICK, goNextScene);
function goNextScene(e:MouseEvent):void {
stage.removeEventListener(KeyboardEvent.KEY_DOWN,doKeyDown);
gotoAndPlay(1,"Scene 2");
Scene 2 code:
stop();
stage.addEventListener(KeyboardEvent.KEY_DOWN, doKeyDown2);
function doKeyDown2(e:KeyboardEvent):void {
switch (e.keyCode) {
case Keyboard.LEFT :
   b2_mc.x -= 5;
   break;
case Keyboard.RIGHT :
   b2_mc.x += 5;
   break;

does it work the same if you use the following? if yes, there's something other than the code you're showing that's causing the problem.
Scene 1 code:
stop();
stage.addEventListener(KeyboardEvent.KEY_DOWN, doKeyDown);
function doKeyDown(e:KeyboardEvent):void {
switch (e.keyCode) {
case Keyboard.LEFT :
   b1_mc.x-=5;
   break;
case Keyboard.RIGHT :
   b1_mc.x+=5;
   if (b1_mc.x>350) {
goNextScene(null);
   break;
next_btn.addEventListener(MouseEvent.CLICK, goNextScene);
function goNextScene(e:MouseEvent):void {
stage.removeEventListener(KeyboardEvent.KEY_DOWN,doKeyDown);
gotoAndPlay(1,"Scene 2");
Scene 2 code:
stop();
stage.addEventListener(KeyboardEvent.KEY_DOWN, doKeyDown2);
function doKeyDown2(e:KeyboardEvent):void {
switch (e.keyCode) {
case Keyboard.LEFT :
   b2_mc.x -= 5;
   break;
case Keyboard.RIGHT :
   b2_mc.x += 5;
   break;

Quad And RAM Problem

Hey all
I just received the 2x1GB modules I ordered from OWC earlier this week... I installed them and unfortunately, the OS is not detecting them... I installed them in the first two available slots, moving outward... I've got 2x256MB at the moment from Apple
So I booted into the Hardware Test and discovered that it's reporting a POST FAILURE on DIMM2/J6900 on the Main window and when I examine the detail view, I see that it's seeing the two new modules... it reports a POST FAILURE on both but given that the main screen is reporting on J6900, I'm guessing that only one is failed and since they're paired, it's failing the 2nd one?
I called OWC and they suggested that I reset the PRAM (no effect) and that I try to install them in other slots... now, I was under the impression that the RAM must be installed in the slots sequentially... is that just a guideline or does it not actually work if I skip a slot? It's easy to test my self but if I don't have to disconnect the G5 again to find out, all the better...
Thanks!

I had the same problem but resolved it by booting in open firmware and reseting the computer. I suggest you do the same.
Put the two 1GB chips in the first paired slots and the two apple chips in the next slots
Boot up holding down Command + Option + O + F until you see the grey screen with text
then run each of these commands
reset-nvram
set-defaults
reset-all
The last one will cause the computer to reboot and you should see all your ram... I hope
Kevan

MSI twin frozr II freeze and glitch problem.

Hi everyone,
I have a very annoying problem with my card. Whenever I play BF3 with a total random time I get some green glitches and the display freeze (see the attached screen).
Normally I get right back on windows with this little popup "display driver stopped answer and recovery successful". But now it just freeze and I have to do a hard reboot...
Here is my config:
-I7 2600k
-Asus p8p67 pro rev 3.1
-2x4Gb Ripjaws X
-OCZ 850w 80gold+
-MSI twin frozr II GTX 580 with latest drivers
-Win 7 64b
I've already look around google, I'm not alone but it seems there is no real solution. It's really sad to have this kind of prob with that expensive card... without any solution.
Some help would be very nice.
Thanks for any help.

Quote from: messem on 08-November-11, 00:11:28
I've never flash my vbios.
But after downloading and trying to flash it with the link you provide nvflash says that my current version is: 70.10.20.00.01 and the one I downloaded is 70.10.17.00.01.
So am I already in the lastest ?
Thanks
this number is not vBIOS ID, so in all cases it will remain the same.

Msi x79a-gd65 8d BSOD and Ram issue, Code 67

Hi,
Specs as follows:
Mobo: msi x79a-gd65 8d (Bios: latest 4.4)
CPU: 3960x
RAM: 2x8GB Corsair dominator platinum 1866MHZ (CMD16GX3M2A1866C10)
PSU: CM 1000watt
GPU: EVGA GTX 680 Classified 4GB
Mobo came back from MSI and they said there were bend pins, they fixed the bent pins. However the mobo still BSODs on stock settings and does not want to boot with 2x8Gb. It only boots with 1 stick.
I also get the code 67.
The mobo is only stable when I enable OC genie and run 1 ram module
Please help, thanks in advance!

>>Clear CMOS<< and retry. If no help try the second stick in any mem slot and see if it boots in any while other stick is installed too. If not try each stick individually to check if both are working.

Msi gt780 illuminated keyboard software and RAM problem

Similar Messages

Maybe you are looking for