MSI K7N2 Delta ISLR help :(

Ive had my current setup for about 5 months now, everything up untill now has run smooth. Yesterday when i woke up i heard my computer makeing this loud noise. when i finaly made it over to the computer i found out that one of my hard drives was spinning super fast and and vibrating in addition to clicking. I then proceded to check all my connections and made sure everything was physicly fine. Once that was done i rebooted my system and got a "array not found" error from the RAID. So i thought what ever, ill just send it back to western digital ( see sig for comp specs)
Today i went to best buy to pick up a western digital 80 gig hard drive to use for the time being. When i get home i pop it in the computer, blah blah blah, wont work, reconnect everything and it went into the windows install. more problems with the computer not detecting my hard drive but i end up fixing it. so finaly i get windows to isntall and i boot up and evertything into windows. install the nforce drivers and reboot and that is the last time my computer has run "normaly"
Now, when i go to boot my computer it takes a good 5 mins to get out of that 8x agp graphic screen from when you first power up, and after that its another minute or so before i get an error saying that there is no system disk.
Prior to all of this nothing crazy was done to the computer, no over clocking or new hardware. everything has been the same for about 2 months.
I might have left a few details out, so please ask for clarification if need be.

Sounds to me like your HD took a dive initially...how that happened is what you're after here...was it just the HD? Was it the controller? Was it a power surge into the system from the PSU caused by the AC in the house/apartment? Basically I sent you to the troubleshooting guide because that's what you're going to need to do to get to the bottom of the issue that you're having...that could entail changing your MB out completely with one of the same model, stripping the system to it's bare minimum, replacing the PSU with (hopefully) something bigger than 300W (these motherboards seem to be power hungry for more than even most generic 350W supplies can provide)...read about PSU's in that guide and what minimum requirements are these days for systems...
Really it comes down to how many components are in your system and how long your underwattage/current PSU can hold out against the strain that you put on it...in my experiences more power is never bad and have an over powered system is far better than cutting it close or being underpowered...this is what I feel you've done to your rig is underpowered it...

Similar Messages

MSI K7N2 Delta-ILSR Help Please.

Hi all
I have a MSI K7N2 Delta-ILSR motherboard that im putting together and I have a question.
In the middle of the socket where the CPU sits is a small CPU thermal protection sensor, my question is that the sensor is higher than the socket and will be touching the CPU when it is inserted is this normal or should sensor be bent downward so not to be in direct contact with the CPU?
I would not be asking this question if not for someone telling me not to put any external case sensor on the CPU direct only on the heat sink but in this case its built into the motherboard itself. Best to be safe than sorry I thought.
Many thanks

Hi Andy
I too have just bought an MSI K7N2-ILSR. On mine the sensor is bent down so as not to contact the cpu. Was like this when I bought it so I would suggest that it is not supposed to touch processor

Help with k7n2 delta-islr

I am thinking about purchasing the cyclone bundle from allstarshop.com
It comes with the msi k7n2 delta-Islr nforce2 ultra 400
With the athalon xp 2500+ barton
512 kingston ddr 400 pc3200 cl 2.5
ati radeon 9500 pro 128k 8x agp.
I will be running windows xp pro
Will this all work together seems the msi board has lots of issues?
Thanks for any help.

Quote
Originally posted by ally68
I am not that concerned with bench marks as I do not play alot to games. I guess what I am asking is the fx cards more compatible also if I do get kingston ddr400 should I get 2 256 stcks or one 512 stick?
For video the TI4600 would be fine and is more reasonably prices. As far as RAM Kingston is not on the approved list, like I said it may work fine or you may have problems depending on the chipset, but no matter what type of RAM you buy you definetly want to buy 2 X 256MHz so you can run dual channel.
Rob

HD Led not working with SATA drives on MSI K7N2 Delta

I noticed the HD led does not work with the SATA drives on my MSI K7N2 Delta ISLR
I confirmed that the led is not burnt out by reconnecting a spare IDE HD with XP on it to IDE 1 and the led worked when there was activity, but it does not work when connected to IDE3 or if the SATA drives are connected to Serial 1 & 2.
Could it be because the motherboard doesn't support and hdd led for the Promise SATA controller.
I had Bios v7.3 and flashed to v7.4 with no luck.
Could a new bios update fix this problem?
Anybody seen this before?

basically it not wired up so works for no one

Kate needs HELP!!! MSI K7N2 Delta ILSR

Guys...
pls help me...
I am assembling, yes I know I am a techi girl...., msik7n2 with radeon9600 and 2xCorsair Value Select 256Mb DDR 400Mhz PC3200 mem...(hence 512mb)
I installed everything assembled it... booted and loaded fine for about 3 times...
and suddenly....
>power on
>no video
>no beeps
>after checking hard nothing happens...
>only thing I can tell is that the d bracket is indicating "memory section"
....d-bracket from MSI K7N2 Delta ILSR is 1,3,4 red and 2 green. Which is according the the manual "Memory Detection Test"-if the memory module is damaged or not installed properly.
Why woudl a memory suddenly not work?
I know I was adjusting bios for this and that....
I think just before this happened.. I adjusted something on agp setting... but what ahs that got to do with memory?
COuld it be the mobo or memory or the video card???
pls help....
My email is [email protected]...
please please help...
and guys in MSI what is your expert opinion? mobo? or memory?
Heeeeeeeeeeeeeeeellllp...
thanks...
Kate x

hi and welcome to this forum.
nice to se a girl here for a change
clear cmos jumper jbat1.
also try safe mode jumper j10 ans j11.
also try to reseat memory and dont trust the dbracket to 100%.
it can show wrong sometimes.
Quote
COuld it be the mobo or memory or the video card???
when you got it running then run http://www.memtest86.com to check memory,
also what psu do you have ?
post max amps on 3.3v 5v and 12v rails.
minimum is 28 35 16.recommended is higher.

MSI K7N2 Delta-ILSR MB Problems, Need Help ASAP!! PLEASE

Ok I just got this motherboard (MSI K7N2 Delta) Yesterday and after getting it setup I began overclocking the Processor (an AMD Athlon XP Barton Mobile 2500+) I was at 11x 215 1.750V Perfectly. I moved to 216 it started to seem unstable so I pushed the VCORE up to 1.775 and tried 217. It couldn't boot so I dropped it back down and decided ok 208 and a 11.5 multi might get me past the 2.4 mark which I was looking for. Well when I changed the Multi. to 11.5 and said save the system just sate as the flashing y for save. I could not change it to n I had already pushed enter So i firgured great and left it alone for a few minutes, nothing so I reset it. Now it refuses to boot/post. It spinds the fans the HD's the Network port is going but I get no picture. I have cleared the CMOS using the jumper I have removed the battery and power for over an hour and I still get nothing. I am assuming this is a BIOS error but I am not sure what to do to fix it. Does anyone here kno maybe, something I have yet to try something I can do? I would hate to RMA it and have to wait on newegg. Hell the thing is a day old. So please any idea's are welcome I have this posted on the Hard Forums as well but I am hopinh this forum may be more popular with getting help as no one is helping over there. Thanks!

Hi,
Cross: Just in case you are doing something wrong there's a clear CMOS guide here, follow it to the letter (and don't forget to put the FSB jumper to SAFE beforehand - there's a note about it in the guide).
How To Clear the CMOS
Your system board or CPU maybe not be dead yet - I had a similar problem with one of my boards and I tried everything - to cut a long story short I eventually got it working!!!
Btw, If you can't boot or get into the BIOS put your other CPU in (clear BIOS again after fitting!), so that you can prove whether your motherboard is working correctly!
Good luck! I'm off ta bed!
Axel

MSI K7N2 Delta-ILSR Dead? Help!

Hey all,
Well, the other day I was on my computer playing a game when my mobo fan started making an odd noise (as if switching rpm), so I took off the side of my case and took a look inside. Everything seemed to be functioning properly, then I switched my cpu fan speed via the pci slot speed control. As I switched from High-Medium-Low, I noticed that the fan actually slowed to the point where I could see the blades spinning, at least for a second or so. I found that rather odd, seeing as how I've never seen a fan (especially a cpu fan) slow to the point that I could see the blades spin. Anyway, a couple of hours later, I shut down and went to sleep.
The next day I had my comp on for about maybe 30mins to an hour or so when suddenly I heard an alarm from the computer speaker, so I was like, ":censored:?" since I had never heard it before. It was evidently the temperature warning, which I had set to 70C. So I shut down within 15 seconds and opened up the side of my case.
I noticed that the cpu fan wasn't moving at all (usually I'd open the case in time to see the spin-down). So I turned the computer back on and the fan didn't budge, so I immediately powered down, assuming that the CPU Fan had died. Later on, I hooked the fan itself up to a free power cord in my sister's computer and booted up, along with the speed controller, flipping from medium to high to low without any problems.
I then did screwed the fan back to the heatsink in my comp and booted up. I went into the bios an noticed that the rpm was 8k, which is way too high for my fan (normally 5k). So i began switching from high, medium, to low once again, then I saw that the rpm reader in the bios went to 0. So I looked back in the side of my case and saw that the cpu fan was once again dead. At this point I concluded that it was the fan and was about to order the Volcano 12.
A day later I placed the fan inside my sister's computer on a free cord, yet again, and yet again, it worked fine.
I once again put it in my computer to test and this time it worked fine, even while switching between speeds. Unfortunately, I then noticed that the mobo fan was not moving, then began to move.
Well, I'm guessing now that it's simply the motherboard that has a short, since both the motherboard fan as well as the cpu fan have randomly been dying the past few days. The motherboard fan; however, has switched rpm many times in the past from 5k to 3k.
It could also be a PSU problem, but I have Antec 400watt psu and it's been working fine for the past 2 years, so I doubt it. I've had the motherboard for a little over a year. I upgraded my cpu from 2200+ to 3000+ in July. That's also when I bought the cpu fan. The motherboard fan began fluctuating in rpm noticeably back in April or May of this year.
Yesterday, I used the computer again and had it on for about 2 hours or so and I had speedfan monitoring the temps and the rpm. The temps stayed relatively stable: 48 cpu, 44 mobo.
But alas, the RPMs were totally [blame me for the swear filter] up. At one point, both the mobo and cpu fan speeds were reading 0, even though both continued to spin within the case and the temps remained the same. Then after 30mins or so, they cpu fan began reading again at 40,000-42,000rpm, which is obviously incorrect, seeing as the fan is rated for around 5k. I got/get the same readings in the bios, both fans reading at 0rpm as they continue to physically spin.
Also, during a number of times that I've started up the comp within the past few days, the motherboard northbridge fan wasn't spinning at all and didn't begin to until a few minutes into my windows session.
Also, I took out the NB fan and noticed a slight crack in the back of it.
I was considering simply just buying the Volcano 12 and the MSI K7N2 Delta2 Platinum rather than RMAing the mobo. Then perhaps an Antec 550W psu, if necessary.
Any ideas what I should replace and in which order? And has anybody else encountered any similar problems with this mobo (at least with the mobo rpm, which has been a prob for about 6months on and off)?
I bought the mobo along with a 2200+ in July of 2003. I upgraded the ram from 256 to 512 in April 2004 (which is around the time I started hearing rpm probs with the mobo fan) and I upgraded the cpu in July of 2004
Many Thanks!
My Specs are as follows:
Windows XP Professional SP1
Antec SX1040B2 File Server Case
400watt Antec PSU
MSI K7N2 Delta-ILSR
AMD Athlon XP 3000+ (2.17GHz)
Thermaltake TR2 M2 HSF
Kingston 256MB of PC2700 DDR-333MHz RAM
Generic 256MB of PC2700 DDR-333MHz RAM
ATI All-In-Wonder 9800 Pro
Sound Blaster Audigy 2ZS Platinum
Pioneer 10x DVD Drive
Sony 8x Double Layer DVD-+RW
Western Digital 120.0GB 7200RPM HD ATA/100
Western Digital 120.0GB 7200RPM HD ATA/100
nForce Ethernet Adapter w/Cable line
Logitech MX500 Optical Mouse
Logitech Elite Keyboard
19" Envision Monitor EN985e
Logitech Z-680 5.1 Speakers

Could be a fluctuating PSU that's breaking down power to the MB. You have a whole lot of components dragging that PSU down. With what you have in your rig I would run either an Antec or Enermax 550W. Best way to be sure is to borrow a PSU or buy one from a store with a good return policy so that you can return it if indeed it turns out to be the MB. If I don't have your board here on my bench to test the only thing I can suggest to you is to swap out components unfortunately.

K7N2 Delta ISLR and XP3200 Woes

Let me share some of my experience with random crashes and lock ups on my main system.
Hopefully some might find it helpful and others might have useful comments to add.
It all started when I decided to upgrade my system. I waited until new technology was announced and then went out and bought the hardware that was knocked off the top spot.
My current system is:
Althon XP3200 Barton
1Gig PC3200 (2x512M)
K7N2 Delta ISLR Bios 7.7
Radeon 9700pro
Antec TruePower 550W PSU
XP Professional
SATA 120G Barracuda
When I first assembled the system I could not, and still cannot, get it to run stable as a XP3200 with a FSB of 200MHz (400MHz) and the memory in dual channel mode. The system wouldn’t boot, would randomly crash, would come up with fatal XP errors.
So after consulting the message boards I was informed it was probably be down to two causes; a inadequate power supply or overheating.
That is when I went out and bought the Antec TruePower 550W PSU. The reason being the CPU temperature was around 47C - 52C (107F - 115F) with ambient around 35C (88F). Not too hot I thought.
Anyway this did not solve the problem so I then decided to change the CPU coolers. I now have a nice collection, Alaska, Aero, Gigabyte and others. Current one on order is SLK-900A with a delta FFB0912EHE fan. But again this did not solve the problem.
I then thought that maybe the ambient inside temperature was too high and therefore pushing the CPU temperature up. To solve this I fitted two hard-drive fans, four 80mm case fans and a PCI exhaust fan. This was on top of the 3 fans already in the system. Still the system would not run. I even took the side panel off and had a 6” mains fan blowing into the case. Still couldn’t make it stable.
I have just ordered a Thermaltake Wingo V8000A case.
So I decided to check out the XP3200 and memory. After playing around I found out that:
1. The memory is fine running dual channel at 400MHz. I ran memtest using my CPU and memory in a friends PC for 12 hours without any problems (Abit board).
2. The system is stable if I drop the FSB to the processor to 166MHz (333MHz). How I am currently run the machine.
3. The system was more stable if I ran the memory in single channel mode.
4. The point it becomes unstable is when the CPU FSB is 192MHz (384Mhz).
5. The problem occurs on another K7N2 Delta ISLR motherboard. Actually exactly the same problem running a different XP3200 and 1Gig.
I have tried all possible combinations in the bios, except Vcore, Vddim voltage levels. Which is my next step. I think I need to up the Vcore at higher frequencies as I believe it may be a bios /motherboard inherent problem.
I hope this might be helpful to some who are experiencing the sample problems.
Couple of things I don’t like about the mother generally a part from the fact I can’t set it up correctly.
1. The decoupling capacitors around the CPU socket are too close. This limits the choice of CPU coolers you can fit.
2. Motherboard components interfere / prevent you from fitting certain cards in the PCI slots. Such as the SPDF adapter that comes with the motherboard.
And does anyone know:
1. What is the maximum temperature I should be seeing for stable operation on a XP3200?
2. Any recommendations on another suitable motherboard? I basically spent all the money I had so if I can’t get it working I’ll bin the motherboard and buy another one.
Oh, why don't I run it at 333MHz? Well then I got a slower system than I started with and it means I admit defeat!

I have this same board with the same BIOS and am also using an Athlon XP 3200+ (with Corsair TWINX1024-3200C2 RAM) and had the same excruciating stability problems. I had tried/tested everything in sight and no stability. Then I found a posting in this forum made a few months back by WebFan (with an XP 3200+ and basically the same RAM), who said he had the same kind of problem. He had only achieved stability when he reduced the FSB setting to 192 MHz (obviously not a coincidence). (Thank you ever so much WebFan.) I reached the heaven of stability by making the same change. Then I started experimenting; I moved the bus speed to 193, still okay. I set the RAM settings to the 3-3-6 2.5 that Corsair says are stable, still okay.
Then, and this I believe is the key step, I installed the lastest set of chipset drivers from nVidia (not the older version provided by MSI). This change subjectively seemed to improve performance noticeably, so I decided to take the big plunge and return the FSB to the rated 200 MHz setting. It's only been three days, but STILL OKAY! Before setting the FSB to 192, I was having all kinds of blue-screen crashes numerous times a day. I haven't had a single one in ten days, three days running at the full 200 MHz.
It seems to me that the board/chipset were not tuned to handle the 3200+. If you look at the description of the board on the MSI global site, it says it's compatible with Athlon XP 3000+ and up. My guess is that only the lastest edition of the drivers, version 4.24/4.27, is up to the job. (I'm not interested in overclocking and so haven't been interested in seeing if I can do better than the rated 200 MHz setting [400 MHz DDR clock speed]. Leave well enough alone, if you ask me.)
Try them; you have nothing to lose but your instability.

Internet Connection Problem on MSI K7N2-Delta-ILSR

Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
Athlon XP 2400+ Overclocked to 2205MHz
2 memory modules of 256MB 400 manufactured by Samsung
TharmalTake Volcano 11
Triplex Xabre 400 PRO with 128MB
Hercules Gamesurrround Fortissimo III 7.1
Microcom InPorte Home modem 56k
Leadtek winfast 2000 (TV/FM radio)
Acard SCSI controller (Acard AEC-6710D) for my scanner
WesternDigital WD800 GB
WesternDigital 15.3gb
Bios ver.7.4
Can anyone help me?

Quote
Originally posted by Roger Wilco
Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
Anyone else in the same boat?
Hi,
Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck
Rob

Data corruption on MSI K7N2 Delta ILSR

Hi all,
Just got my new MSI K7N2 Delta ILSR up and running.
Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum )
While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
Then the overclocking began I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
When using an FSB of 166mhz no data corruption or crc errors.
What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
Help!
gr,
Remco

Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended
Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome
gr,
Remco

FLASH BIOS MSI K7N2 Delta-ILSR ????????

I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
Thank you
My system:
WinXP Pro
MSI K7N2 Delta-ILSR
AMD 2500+
1 GB DR3200
Seagate 160 SATA

http://www.msi.com.tw/html/support/bios/note/ntfs.htm

Msi k7n2 delta ilsr problem

hi i have this configuration on my pc:
antec true control 550 watts
msi k7n2 delta ilsr
kingston hyper x pc3700 2x512 mb
athlon xp 3200+
seagate 120 gb sata 7200.7 hd
ati radeon 9800 pro excalibur ice q
i have 2 problems : the first one is that sometimes windows display me a blue screen with certain problem related to ati2dg.dll i think that problem is beacause the video card so i decided to update the bios , in the live update page from msi says that the bios 7.6 fix a bug with ati vga cards but after flashing and updating to bios v7.6 that blue screen with the same error still appearing so i dont know what else to do to solve the problem and the second one is that when i start any game or make the processor to work a little mostly related with video stuff the case speaker start to beep and the pc lags until he restarts with no reason i really dont know why if u can help me thank you

Foxtrotccs,
In the BIOS try setting the AGP to 4X and disable Sidebanding. Then set the AGP Apeture to 256. See if that helps.
Make sure you are running the lastest nVidia nForce Drivers and the latest ATI Catalyst Drivers
Take Care,
Richard
P.S. There is still a possibility that the Kingston RAM is the problem.

MSI K7N2 Delta ILSR Questions & RAID Promise FastTrak Controller Issue

I have recently rebuilt my system replacing the MSI KT3 with an MSI K7N2 Delta. I have been impressed with the features and stability of the system, however, I have some questions that I hope some of you that have more experience of this board can answer:
1. I am using the AMD Athlon XP 2200 (and all the other components including the Lian Li case) which I was using on the KT3 board. The CPU temperature is around 45 degrees C but on the KT3 it was only 35 degrees C when idle. Any ideas ? The heatsink is definetly mounted properly. The temperature did drop by 10 degrees C when I flashed the
BIOS to fix the known CPU temperature issue but I think its still high.
2. I do not have any serial ATA devices or anything connected to IDE3 channel and during the BIOS boot up I get the message:
"No drives attached to FastTrak Controller. Bios Not installed."
Is this correct ? Should I be getting this message ?
I would like to disable the onboard Promise Controller since it is taking up resources and it slows down the boot speed (although only slightly). The MSI website says that the onboard RAID controller can't be disabled. I think this is poor design. Does anyone know if this is going to be addressed in future BIOS releases ?
3. Which of the USB ports are USB 2.0 and USB 1.1. I thought it was rather strange that only 2 of the 4 ports on the header actually active.
Many thanks for your help.
Rupesh

First off your temp is ok on that board. If you have not loaded the onboard raid driver do so and it is something you have to suffer with on the MSI board. All of your USB ports should run at USB 2.0 and you also should be able enable all of them in the bios.

MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chip

I tried to install 3 of the Crucial Ballistix Tracer (1 Gig Each) in this motherboard (MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chipset) and it will not run stabilly no matter what I tried. Is this a bios conflict with the memory? If so, are there any new bios updates? I have tried cas settings and voltage settings but nothing works. It will how ever run perfectly with only 2 sticks in single channel mode. It will not run same 2 sticks in dual channel mode. Anyone have any ideas? Anyone know of any new motherboards with maybe NFORCE 4 Chipset that support all 3 sticks of this memory and an AGP graphics card? Im thinking of a new motherboard but I still need to have AGP and SATA.
Barton 3200 core proc.
System has ran fine for a solid year until I tried new memory. Please help!

Quote from: freakytiki4u on 07-November-06, 23:42:33
Ok I tried to use relaxed FSB by -10 and relaxed mem timings but still unstable due to the motherboard trying to use dual channel memory. If you can modify the bios to where it will not have the capability of dual channel memory I truly believe it will work. Will u try this for me? I would greatly appreciate it as I am really not ready to spend all the money on new equipemtn when this suits my needs for now.
sure but as i said before this is gona be experimental and risky. Here we go:
MSI K7N2 Delta ILSR Experimental MOD E1(Disable Dual CH ability)
Procedure is automated in best possible safest way to BIOS update.
Prepare a blank diskette in a good condition(newest one etc.)
]execute file under XP will make bootdisk with automated BIOS update procedure. when diskette is ready, reboot PC and boot from FDD(floppy), wait a bit, then you will be asked for final confirmation about BIOS update process, press a key to proceed, after BIOS update is complete, ensure that you got successfully output message from flash program. then power down your PC, remove power cord from the PSU, hit power button several time to drain caps electrify, touch with hands some metal for ES discharge, and Clear CMOS.
pull back power cord, power up your PC, when you see CMOS checksum error,(expected msg) hit F1 to continue to re-build DMI pool data, then reboot and enter in BIOS, LOAD BIOS DEFAULT, and SAFE AND EXIT.
NOTE: Ensure your PC is stable before proceed with BIOS update.
NOTE: Use it at own risk, chance of failure is big, cannot guarantee results and safest as provisional mode which can guarantee it will work stable with features. also cannot test it personally before give you. (don't have mobo anymore)
Using it may end with dead mainboard (BIOS chip re-flash will be required, if somethink goes wrong)

MSI K7N2 Delta-ILSR (MS-6570) BSOD problems grrr

I recently purchased this board and although it is an awesome product, I'm having a problem with BSOD's when I play a game for a certain period of time
Specs:
MSI K7N2 Delta-ILSR (7.6 BIOS)
AMD Athlon XP 2800+ Barton
512MB (2x256MB) Samsung PC-2700 DDR memory (2.5-3-3-6 1T)
MSI 128MB GeForce4 Ti 4200 (4X AGP)
NVIDIA nForce on-board sound
Western Digital 80GB drive w/ 8MB cache
MSI X48 CD/CD-RW/DVD combo drive
Windows XP Professional SP1
PSU:
Turbolink 420watt (came with case)
+3.3V is 28A
+5V is 40A
+12V is 18A
So what happens is I get a STOP error during the game that shows the kmixer.sys driver as the culprit. Sometimes it's accompanied by PAGE_FAULT_IN_NON_PAGED_AREA too. I read somewhere that kmixer.sys has to do with windows audio and that it's a 3rd party driver issue or a memory issue. I'm using the latest NVIDIA 3.13 nForce platform drivers. I ran Memtest lastnight for 12 hours straight and 0 errors. I'm thinking the memory may not be compatible with the board nor dual channel, is this possible? I have also tried several different drivers for both video and chipset including MSI's own and I still get the kmixer.sys BSOD when playing games. My previous motherboard was an MSI KT3 Ultra2-R (MS-6380E) which I had no issues with. Any help would be greatly appreciated. Thank you in advance.
--Update--
I just tried to play a game with audio disabled and it crashed this time with DRIVER_IRQL_NOT_LESS_OR_EQUAL with nv4_mini.sys as the problem. My IRQ table shows some sharing, but device manager shows no conflicts.

Ok I tried running the DTM-CB3 module which is nForce2 approved at 3-4-4-11 2T timings and experienced the same result even at 2.6 and 2.7v. I tried both in dual-channel and same thing happened. However, I downloaded a program called Prime95 and ran the CPU torture test and the system returned a fatal error within the first few minutes. CPU Temp was at 57 C and the warning beep (set to 60C though) sounded intermittentley which is strange. I let it cool down then ran the torture test again and about 5min. later the system either seized completely or the program crashed. IE has also crashed randomly on me. I did this several times, before trying a different FSB/DRAM ratio. So I left the system at 200 FSB and used a 6:5 ratio so my memory was running at DDR333 and processor was a 3200+. I ran Prime95 again and the system locked up just as it did the other times. So after I did this a few times with consistent results. I went back and set the FSB to 166 and tried a 5:6 ratio so the memory was DDR400 and processor was the normal 2800+. I ran it again and to my suprise it passed all the tests and after an hour of this, I tried a game and that was perfectly fine as well. I checked the temps and CPU was only 45 C this time. So I'm thinking the processor can't handle anything above 50C or it's just plain overheating. I ordered a Thermaltake Silent Boost HSF today which is tested up to 3400+ so this should fix my problem. If not, then I'm going to replace the memory with a 512MB Geil PC3200 golden dragon dual-channel kit.

MSI K7N2 Delta ISLR help :(

Similar Messages

Maybe you are looking for