MSI K7N2 DELTA L BSOD Booting to DIsk/XP CDROM

Installed the MB tonight. Cannot boot to existing WINXP home. Get BSOD whel loading. Stop Error 7B. Cannot boot from XP Home CD. Some other BSOD stop error.
Bios pretty much defaults. Disables a few things like serial ports (been disabled on other MB as well).
System has been fine on SoYo Dragon Ultra Black. Installed ECS K7VTA3 yesterday. System worked OK, but decided to go to MSI today. Now, no boot.
Tried changing memory, disconnecting all but boot disk, no luck.
Any ideas?
- webpro

it will never boot if it has another chips sets ide drivers on it
you will have to overinstall at least
post psu max amps as these seem to need a lot of power
3.3 5 and 12v Power Supply Guide

Similar Messages

MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

Hi
i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
unfortuntly i can't boot it. it wont show anything on screen.
i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
all i get is :
blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
cpu: AMD xp 3200+ 400fsb.
i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
i also e-mailed MSI support that question. (2 days ago. no answer yet)
oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
can you help me?

hi guys
here is my PSU specs:
Colors-It 500w-Max Silent ATX Power Supply
Voltage 115/230V
Current 10A/5A
Frequency 60/50Hz
+3.3 +5 +12 -12 -5 +5SB BLK GRN GRY
30A 50A 15A 1.0A 1.0A 2.5A COM P-ON PG
connectors:
ATX-2.03 Connector: 1
ATX-12V Connector: 1
CD-Rom/HD 4 Pin connector: 6
Floppy 4 Pin Connector: 2
Serial ATA Connector : 1
cpu: AMD Athlon XP 3200+
MotherBoard: MSI K7N2 Delta-ILSR More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
Memory: kingstone 512mb pc3200 400MHz x2 More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
i have other brand of memory moduls (micron pc2300) i tried them too. no go.
i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
as i said before, i have pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
but if mobo not showing bios, i can't update bios from floppy.
and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

MSI K7N2 Delta-ILSR (MS-6570) BSOD problems grrr

I recently purchased this board and although it is an awesome product, I'm having a problem with BSOD's when I play a game for a certain period of time
Specs:
MSI K7N2 Delta-ILSR (7.6 BIOS)
AMD Athlon XP 2800+ Barton
512MB (2x256MB) Samsung PC-2700 DDR memory (2.5-3-3-6 1T)
MSI 128MB GeForce4 Ti 4200 (4X AGP)
NVIDIA nForce on-board sound
Western Digital 80GB drive w/ 8MB cache
MSI X48 CD/CD-RW/DVD combo drive
Windows XP Professional SP1
PSU:
Turbolink 420watt (came with case)
+3.3V is 28A
+5V is 40A
+12V is 18A
So what happens is I get a STOP error during the game that shows the kmixer.sys driver as the culprit. Sometimes it's accompanied by PAGE_FAULT_IN_NON_PAGED_AREA too. I read somewhere that kmixer.sys has to do with windows audio and that it's a 3rd party driver issue or a memory issue. I'm using the latest NVIDIA 3.13 nForce platform drivers. I ran Memtest lastnight for 12 hours straight and 0 errors. I'm thinking the memory may not be compatible with the board nor dual channel, is this possible? I have also tried several different drivers for both video and chipset including MSI's own and I still get the kmixer.sys BSOD when playing games. My previous motherboard was an MSI KT3 Ultra2-R (MS-6380E) which I had no issues with. Any help would be greatly appreciated. Thank you in advance.
--Update--
I just tried to play a game with audio disabled and it crashed this time with DRIVER_IRQL_NOT_LESS_OR_EQUAL with nv4_mini.sys as the problem. My IRQ table shows some sharing, but device manager shows no conflicts.

Ok I tried running the DTM-CB3 module which is nForce2 approved at 3-4-4-11 2T timings and experienced the same result even at 2.6 and 2.7v. I tried both in dual-channel and same thing happened. However, I downloaded a program called Prime95 and ran the CPU torture test and the system returned a fatal error within the first few minutes. CPU Temp was at 57 C and the warning beep (set to 60C though) sounded intermittentley which is strange. I let it cool down then ran the torture test again and about 5min. later the system either seized completely or the program crashed. IE has also crashed randomly on me. I did this several times, before trying a different FSB/DRAM ratio. So I left the system at 200 FSB and used a 6:5 ratio so my memory was running at DDR333 and processor was a 3200+. I ran Prime95 again and the system locked up just as it did the other times. So after I did this a few times with consistent results. I went back and set the FSB to 166 and tried a 5:6 ratio so the memory was DDR400 and processor was the normal 2800+. I ran it again and to my suprise it passed all the tests and after an hour of this, I tried a game and that was perfectly fine as well. I checked the temps and CPU was only 45 C this time. So I'm thinking the processor can't handle anything above 50C or it's just plain overheating. I ordered a Thermaltake Silent Boost HSF today which is tested up to 3400+ so this should fix my problem. If not, then I'm going to replace the memory with a 512MB Geil PC3200 golden dragon dual-channel kit.

HD or Booting problem on MSI K7N2 Delta 2 Platinum

Hi all,
Ive a weird issue which i cant figure out myself. I've 2 HD's..lets call them A and B where A = 60Gb (Master) and B = 80Gb (Slave)
It's is like this:
A and B are connected to the primary IDE-slot. A will boot when set as Master and B wont start booting when set as Slave mode (i mean, it wont show/appear in the first hardware (detection) bootscreen of yer BIOS where it says its present or the so called POST-screen), but if I set B as Master only (A turned off) it will boot.
What also happens is if I disconnect the power of drive B..drive A will boot..and while OS is loaded...I turn on the powercable from drive B and reboot..suddenly out of the blue it detects both HD's and reboots like it should do normally...but when i reboot from than..the same thing happens again..(it wont recognize B anymore)
Sumtime it regonizes both drives and sumtime it just won't and sumtimes just 1 drive..
Another thing, when it won't recognize one or sumtime both drives...the POST-screen gets stuck at the name and version of the BIOS...and where it says: 'detecting IDE drives...' when it is at this stage..and I press on the DEL-key for example..it's loading damn too slow..I've to wait about 10min before it enters the BIOS-setup..
I am 100% sure I set the jumper correctly for Master or Slave mode on my HD..I know there's sumthing wrong..but don't know where...Ive changed the jumper with a new one ..switched IDE-cables...switched HD's (set B as Master and A as Slave and vice versa, knowing there is no active partition on B..but only to check if it recognizes the drive)..in all cases..the BIOS settings are set as default!
any1 can help me out with this?
It worked smoothly on my system till i noticed my second MEM bank of my mobo broke (Asus A7N8X-E)..so i had to change it quickly (and went to the store with my warranty to fix this board..it was only 3 months old) ..since I've seen/had enough Asus mobo's in my life I went this time for an MSI which looks better in my opinion...so now i have an MSI K7N2 Delta 2 Platinum..it works fine...except that HD issue mentioned above
any help would be appreciated..thnx in advance!
cheers!

Hi,
I've done that already several times...it doesnt work..any other suggestions?
Now I can boot normally when I disconnect the power of the 2nd HD (or just any HD)...when the os is loaded...I turn back on the power of the 2nd drive and reboot...than it will run/boot/restart etc..normally...this is the only workaround I have at the moment...this only works when the system is turned a long time...
My power supply is 400W..so I don't think Ive any prob with that
cheers

MSI K7N2 DELTA -L (601-6570-020) nFORCE 2 DUAL 400 , RANDOM RESTART PROBLEM (WinXP,Win98)

Machine Specs:
- AMD Athlon XP 2600+ With L2 512 KB (Model 10)
- MSI K7N2 Delta -L nFORCE 2 Ultra 400 (601-670-020) (My AwardBios is updated to v5.7, Using nVIDIA`s O/B Audio and Ethernet Controllers)
- TwinMOS PC3200(CL2.5) 512 MB DDR400 RAM (Desktop Series)
- Samsung SpinPoint (SP0411N) 40 GB 7200 Rpm HDD
- GeForce2 MX400 64MB AGP 4x (Oem Manufacturer)
- Samsung SyncMaster 753s 17" Monitor
- Sony 52x Cd-Rom
- Philips Stereo Headphones
- Windows XP Home Edition Turkish (Service Pack 1 Turkish) , I did all of critical and other updates ,Totally up to date.Device drivers are too...(nForce 3.13 whql International,Forceware 56.72 whql International)
Problem :
- ERROR EVENT : 1003 ERROR NAME : IRQL_NOT_LESS_OR_EQUAL
Original Error Texts:
A problem has been detected & Windows has been shut down to prevent damage to your computer.
IRQL_NOT_LESS_OR_EQUAL
If this is the first time you've seen this Stop error screen, restart the computer. If this screen appears again follow these steps.
Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If the problem continues, disable or remove any newly installed hardware or software.
Disable BIOS memory options such as caching or shadowing.
If you need to use safe mode to remove or disable components restart your computer, Press F8 to select Advanced Start-up options & select Safe Mode.
Technical Information :
*** STOP: 0x0000000A (0x00000004, 0x00000002, 0x00000001, 0x804F1473)
Beginning dump of physical memory
Physical memory dump complete. Contact your system Administrator or technical support group for further assistance.
After restarting manually from the PC. I get the following message
The system has recovered from a serious error.
BCCode : a BCP1 : 00000004 BCP2 : 00000002 BCP3 : 00000000
BCP4 : 804F1ADA OSVer : 5_1_2600 SP : 0_0 Product : 256_1
C:\WINDOWS\Minidump\Mini042202-01.dmp
C:\DOCUME~1\DANIEL~1\LOCALS~1\Temp\WER3.tmp.dir00\sysdata.xml
And when I check EVENT VIEWER
Event Type: Error
Event Source: System Error
Event Category: (102)
Event ID: 1003
Date: 22/04/2002
Time: 5:55:03 PM
User: N/A
Computer: XXX-BOX
Description:
Error code 0000000a, parameter1 00000004, parameter2 00000002, parameter3 00000000, parameter4 804f1ada.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 53 79 73 74 65 6d 20 45 System E
0008: 72 72 6f 72 20 20 45 72 rror Er
0010: 72 6f 72 20 63 6f 64 65 ror code
0018: 20 30 30 30 30 30 30 30 0000000
0020: 61 20 20 50 61 72 61 6d a Param
0028: 65 74 65 72 73 20 30 30 eters 00
0030: 30 30 30 30 30 34 2c 20 000004,
0038: 30 30 30 30 30 30 30 32 00000002
0040: 2c 20 30 30 30 30 30 30 , 000000
0048: 30 30 2c 20 38 30 34 66 00, 804f
0050: 31 61 64 61 1ada
I installed 6 operating systems on my pc (WinXp Home Edition Turkish/English,WinXP Pro Turkish/English,Win98 Turkish/English) and tested it, but every time i meet the same thing (MS Blue Screen Of Death Sux...).I checked the WinXP`s logs and searched for error code`s meaning from microsoft knowledge database. They are saying nothing about this problem but the problem`s root is coming from a bad device driver. It seems to be a generic problem for all operating systems cuz all of them were restarting themselves randomly, before i close "auto-restart on critical errors" option.After i saw some messages on forums , i searched for my RAM maker`s home page then i learned that my RAM is assembled with VIA KT Series and SIS chips & optimized for them. I think nForce is too picky about rams.But i aint sure about where the hell is this problem coming from. If you guys are sure about that is an unsupported ram problem and knew the list of ram marks&models that supported by MSI K7N2 Delta -L ,please help me about this damn problem. Thanks for your help.
Note : I tried Asus Ati Radeon 9200SE 64mb g.adapter (some peoples told me thats about g.adapter), but problem continued.

If I read correctly in your specs I see only 11 Amps on the +12v Rail. Is this correct?
If so, I'd advise a PSU that has at least 18 amps on the +12v Rail, perhaps as low as 16 with the other rails to match as shown currently in your spec.
11 Amps is just way too underpowered for that rig. I am surprised it even boots.
At what point does the BSOD occur?

Internet Connection Problem on MSI K7N2-Delta-ILSR

Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
Athlon XP 2400+ Overclocked to 2205MHz
2 memory modules of 256MB 400 manufactured by Samsung
TharmalTake Volcano 11
Triplex Xabre 400 PRO with 128MB
Hercules Gamesurrround Fortissimo III 7.1
Microcom InPorte Home modem 56k
Leadtek winfast 2000 (TV/FM radio)
Acard SCSI controller (Acard AEC-6710D) for my scanner
WesternDigital WD800 GB
WesternDigital 15.3gb
Bios ver.7.4
Can anyone help me?

Quote
Originally posted by Roger Wilco
Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
Anyone else in the same boat?
Hi,
Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck
Rob

Kate needs HELP!!! MSI K7N2 Delta ILSR

Guys...
pls help me...
I am assembling, yes I know I am a techi girl...., msik7n2 with radeon9600 and 2xCorsair Value Select 256Mb DDR 400Mhz PC3200 mem...(hence 512mb)
I installed everything assembled it... booted and loaded fine for about 3 times...
and suddenly....
>power on
>no video
>no beeps
>after checking hard nothing happens...
>only thing I can tell is that the d bracket is indicating "memory section"
....d-bracket from MSI K7N2 Delta ILSR is 1,3,4 red and 2 green. Which is according the the manual "Memory Detection Test"-if the memory module is damaged or not installed properly.
Why woudl a memory suddenly not work?
I know I was adjusting bios for this and that....
I think just before this happened.. I adjusted something on agp setting... but what ahs that got to do with memory?
COuld it be the mobo or memory or the video card???
pls help....
My email is [email protected]...
please please help...
and guys in MSI what is your expert opinion? mobo? or memory?
Heeeeeeeeeeeeeeeellllp...
thanks...
Kate x

hi and welcome to this forum.
nice to se a girl here for a change
clear cmos jumper jbat1.
also try safe mode jumper j10 ans j11.
also try to reseat memory and dont trust the dbracket to 100%.
it can show wrong sometimes.
Quote
COuld it be the mobo or memory or the video card???
when you got it running then run http://www.memtest86.com to check memory,
also what psu do you have ?
post max amps on 3.3v 5v and 12v rails.
minimum is 28 35 16.recommended is higher.

FLASH BIOS MSI K7N2 Delta-ILSR ????????

I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
Thank you
My system:
WinXP Pro
MSI K7N2 Delta-ILSR
AMD 2500+
1 GB DR3200
Seagate 160 SATA

http://www.msi.com.tw/html/support/bios/note/ntfs.htm

Sudden Restarts MSI K7n2 DELTA ILSR

I've had this setup for about a year now.
Sudden restarts now plague my system, no virus found per NAV 2004, ran processor burn in wizard, SISOFT sandra, on cpu arithmetic and cpu multimedia setting, 100 cycles (no problems) windows memtest ran with no errors via start up disk full cycle of tests.
Have reloaded video drivers,to no avail, this happens about once a week, any ideas????
MSI k7n2 delta ILSR Bios version 7.7
1.5 Gig Micron PC 3200 (512x3) RAM supporting dual channel stock voltage
mixed bag o ram, crucial, micron technology, and, patriot
Athlon xp 2500 stock voltage
SLK 900A heatsink with 80 mm tornado (temps at idle 35-38c) (42 load)
Creative SB Live
Nvidia 256 mb asylum video card GE FORCE USR DATA PCI FAX Modem (V92) 5610b
Hercules 420W PS
All drivers are up to date and windows update run regularly (Win XP Pro SP2)
[/COLOR]

Quote
Originally posted by scooter787b
well for one thing the k7n2 series can only support 2 pc3200 dimms,
are you really sure ?
my motherboard which is rather old now supports 3 pc3200 dimms.
norton antivirus is CRAP.
i stopped using it when i found my harddrive was full of viruses.
try avg6 for example which is free.

MSI K7N2 Delta-ILSR MB Problems, Need Help ASAP!! PLEASE

Ok I just got this motherboard (MSI K7N2 Delta) Yesterday and after getting it setup I began overclocking the Processor (an AMD Athlon XP Barton Mobile 2500+) I was at 11x 215 1.750V Perfectly. I moved to 216 it started to seem unstable so I pushed the VCORE up to 1.775 and tried 217. It couldn't boot so I dropped it back down and decided ok 208 and a 11.5 multi might get me past the 2.4 mark which I was looking for. Well when I changed the Multi. to 11.5 and said save the system just sate as the flashing y for save. I could not change it to n I had already pushed enter So i firgured great and left it alone for a few minutes, nothing so I reset it. Now it refuses to boot/post. It spinds the fans the HD's the Network port is going but I get no picture. I have cleared the CMOS using the jumper I have removed the battery and power for over an hour and I still get nothing. I am assuming this is a BIOS error but I am not sure what to do to fix it. Does anyone here kno maybe, something I have yet to try something I can do? I would hate to RMA it and have to wait on newegg. Hell the thing is a day old. So please any idea's are welcome I have this posted on the Hard Forums as well but I am hopinh this forum may be more popular with getting help as no one is helping over there. Thanks!

Hi,
Cross: Just in case you are doing something wrong there's a clear CMOS guide here, follow it to the letter (and don't forget to put the FSB jumper to SAFE beforehand - there's a note about it in the guide).
How To Clear the CMOS
Your system board or CPU maybe not be dead yet - I had a similar problem with one of my boards and I tried everything - to cut a long story short I eventually got it working!!!
Btw, If you can't boot or get into the BIOS put your other CPU in (clear BIOS again after fitting!), so that you can prove whether your motherboard is working correctly!
Good luck! I'm off ta bed!
Axel

MSI K7N2 Delta ILSR Questions & RAID Promise FastTrak Controller Issue

I have recently rebuilt my system replacing the MSI KT3 with an MSI K7N2 Delta. I have been impressed with the features and stability of the system, however, I have some questions that I hope some of you that have more experience of this board can answer:
1. I am using the AMD Athlon XP 2200 (and all the other components including the Lian Li case) which I was using on the KT3 board. The CPU temperature is around 45 degrees C but on the KT3 it was only 35 degrees C when idle. Any ideas ? The heatsink is definetly mounted properly. The temperature did drop by 10 degrees C when I flashed the
BIOS to fix the known CPU temperature issue but I think its still high.
2. I do not have any serial ATA devices or anything connected to IDE3 channel and during the BIOS boot up I get the message:
"No drives attached to FastTrak Controller. Bios Not installed."
Is this correct ? Should I be getting this message ?
I would like to disable the onboard Promise Controller since it is taking up resources and it slows down the boot speed (although only slightly). The MSI website says that the onboard RAID controller can't be disabled. I think this is poor design. Does anyone know if this is going to be addressed in future BIOS releases ?
3. Which of the USB ports are USB 2.0 and USB 1.1. I thought it was rather strange that only 2 of the 4 ports on the header actually active.
Many thanks for your help.
Rupesh

First off your temp is ok on that board. If you have not loaded the onboard raid driver do so and it is something you have to suffer with on the MSI board. All of your USB ports should run at USB 2.0 and you also should be able enable all of them in the bios.

MSI K7N2 Delta-ILSR Dead? Help!

Hey all,
Well, the other day I was on my computer playing a game when my mobo fan started making an odd noise (as if switching rpm), so I took off the side of my case and took a look inside. Everything seemed to be functioning properly, then I switched my cpu fan speed via the pci slot speed control. As I switched from High-Medium-Low, I noticed that the fan actually slowed to the point where I could see the blades spinning, at least for a second or so. I found that rather odd, seeing as how I've never seen a fan (especially a cpu fan) slow to the point that I could see the blades spin. Anyway, a couple of hours later, I shut down and went to sleep.
The next day I had my comp on for about maybe 30mins to an hour or so when suddenly I heard an alarm from the computer speaker, so I was like, ":censored:?" since I had never heard it before. It was evidently the temperature warning, which I had set to 70C. So I shut down within 15 seconds and opened up the side of my case.
I noticed that the cpu fan wasn't moving at all (usually I'd open the case in time to see the spin-down). So I turned the computer back on and the fan didn't budge, so I immediately powered down, assuming that the CPU Fan had died. Later on, I hooked the fan itself up to a free power cord in my sister's computer and booted up, along with the speed controller, flipping from medium to high to low without any problems.
I then did screwed the fan back to the heatsink in my comp and booted up. I went into the bios an noticed that the rpm was 8k, which is way too high for my fan (normally 5k). So i began switching from high, medium, to low once again, then I saw that the rpm reader in the bios went to 0. So I looked back in the side of my case and saw that the cpu fan was once again dead. At this point I concluded that it was the fan and was about to order the Volcano 12.
A day later I placed the fan inside my sister's computer on a free cord, yet again, and yet again, it worked fine.
I once again put it in my computer to test and this time it worked fine, even while switching between speeds. Unfortunately, I then noticed that the mobo fan was not moving, then began to move.
Well, I'm guessing now that it's simply the motherboard that has a short, since both the motherboard fan as well as the cpu fan have randomly been dying the past few days. The motherboard fan; however, has switched rpm many times in the past from 5k to 3k.
It could also be a PSU problem, but I have Antec 400watt psu and it's been working fine for the past 2 years, so I doubt it. I've had the motherboard for a little over a year. I upgraded my cpu from 2200+ to 3000+ in July. That's also when I bought the cpu fan. The motherboard fan began fluctuating in rpm noticeably back in April or May of this year.
Yesterday, I used the computer again and had it on for about 2 hours or so and I had speedfan monitoring the temps and the rpm. The temps stayed relatively stable: 48 cpu, 44 mobo.
But alas, the RPMs were totally [blame me for the swear filter] up. At one point, both the mobo and cpu fan speeds were reading 0, even though both continued to spin within the case and the temps remained the same. Then after 30mins or so, they cpu fan began reading again at 40,000-42,000rpm, which is obviously incorrect, seeing as the fan is rated for around 5k. I got/get the same readings in the bios, both fans reading at 0rpm as they continue to physically spin.
Also, during a number of times that I've started up the comp within the past few days, the motherboard northbridge fan wasn't spinning at all and didn't begin to until a few minutes into my windows session.
Also, I took out the NB fan and noticed a slight crack in the back of it.
I was considering simply just buying the Volcano 12 and the MSI K7N2 Delta2 Platinum rather than RMAing the mobo. Then perhaps an Antec 550W psu, if necessary.
Any ideas what I should replace and in which order? And has anybody else encountered any similar problems with this mobo (at least with the mobo rpm, which has been a prob for about 6months on and off)?
I bought the mobo along with a 2200+ in July of 2003. I upgraded the ram from 256 to 512 in April 2004 (which is around the time I started hearing rpm probs with the mobo fan) and I upgraded the cpu in July of 2004
Many Thanks!
My Specs are as follows:
Windows XP Professional SP1
Antec SX1040B2 File Server Case
400watt Antec PSU
MSI K7N2 Delta-ILSR
AMD Athlon XP 3000+ (2.17GHz)
Thermaltake TR2 M2 HSF
Kingston 256MB of PC2700 DDR-333MHz RAM
Generic 256MB of PC2700 DDR-333MHz RAM
ATI All-In-Wonder 9800 Pro
Sound Blaster Audigy 2ZS Platinum
Pioneer 10x DVD Drive
Sony 8x Double Layer DVD-+RW
Western Digital 120.0GB 7200RPM HD ATA/100
Western Digital 120.0GB 7200RPM HD ATA/100
nForce Ethernet Adapter w/Cable line
Logitech MX500 Optical Mouse
Logitech Elite Keyboard
19" Envision Monitor EN985e
Logitech Z-680 5.1 Speakers

Could be a fluctuating PSU that's breaking down power to the MB. You have a whole lot of components dragging that PSU down. With what you have in your rig I would run either an Antec or Enermax 550W. Best way to be sure is to borrow a PSU or buy one from a store with a good return policy so that you can return it if indeed it turns out to be the MB. If I don't have your board here on my bench to test the only thing I can suggest to you is to swap out components unfortunately.

MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chip

I tried to install 3 of the Crucial Ballistix Tracer (1 Gig Each) in this motherboard (MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chipset) and it will not run stabilly no matter what I tried. Is this a bios conflict with the memory? If so, are there any new bios updates? I have tried cas settings and voltage settings but nothing works. It will how ever run perfectly with only 2 sticks in single channel mode. It will not run same 2 sticks in dual channel mode. Anyone have any ideas? Anyone know of any new motherboards with maybe NFORCE 4 Chipset that support all 3 sticks of this memory and an AGP graphics card? Im thinking of a new motherboard but I still need to have AGP and SATA.
Barton 3200 core proc.
System has ran fine for a solid year until I tried new memory. Please help!

Quote from: freakytiki4u on 07-November-06, 23:42:33
Ok I tried to use relaxed FSB by -10 and relaxed mem timings but still unstable due to the motherboard trying to use dual channel memory. If you can modify the bios to where it will not have the capability of dual channel memory I truly believe it will work. Will u try this for me? I would greatly appreciate it as I am really not ready to spend all the money on new equipemtn when this suits my needs for now.
sure but as i said before this is gona be experimental and risky. Here we go:
MSI K7N2 Delta ILSR Experimental MOD E1(Disable Dual CH ability)
Procedure is automated in best possible safest way to BIOS update.
Prepare a blank diskette in a good condition(newest one etc.)
]execute file under XP will make bootdisk with automated BIOS update procedure. when diskette is ready, reboot PC and boot from FDD(floppy), wait a bit, then you will be asked for final confirmation about BIOS update process, press a key to proceed, after BIOS update is complete, ensure that you got successfully output message from flash program. then power down your PC, remove power cord from the PSU, hit power button several time to drain caps electrify, touch with hands some metal for ES discharge, and Clear CMOS.
pull back power cord, power up your PC, when you see CMOS checksum error,(expected msg) hit F1 to continue to re-build DMI pool data, then reboot and enter in BIOS, LOAD BIOS DEFAULT, and SAFE AND EXIT.
NOTE: Ensure your PC is stable before proceed with BIOS update.
NOTE: Use it at own risk, chance of failure is big, cannot guarantee results and safest as provisional mode which can guarantee it will work stable with features. also cannot test it personally before give you. (don't have mobo anymore)
Using it may end with dead mainboard (BIOS chip re-flash will be required, if somethink goes wrong)

[MSI K7N2 Delta-ILSR] Trouble

Hello,
I have some serious trouble with my pc, my system specs are:
-Unlocked Amd 2400+ (AXDA2400DKV3C from August 21, 2002)
-Msi K7N2 delta-ilsr
-Palit GeForce FX5900XT
-Std. 512mb pc2700
-Std. 512mb pc3200
-More stuff
The problem is that I can't change the multiplier. If I change the multiplier from 15x (standart) to for example 13x, the system won't boot. Than I have to put a jumper at the 100mhz fsb setting, then I must change the multiplier back to by h/w & save the settings. So I am only able to change the fsb, but not the multiplier
Anywone who know's a solution for this problem?
Thanks,
Sape

Quote
Originally posted by Wonkanoby
http://www.nforcershq.com/forum/viewtopic.php?t=48585
i told how to there
Yes but I would like to be shore
Quote
Originally posted by Tango
How do u know that your CPU is unlocked?
Sounds like to me it is locked because you can change the fsb and not the multiplier.
Because the processor is from 2002, and then it's unlocked

MSI K7N2 Delta ILSR and Serial ATA Drive

I've got a very strange problem....
Yesterday i have installed my new motherboard (MSI K7N2 Delta ILSR) but i have a problem with the SATA feature.
I've got two drives : one 40GB ATA (Western Digital) and one 160GB SATA also from Western Digital.
My SATA drive is recognized by the FastTrak BIOS (v2) but i'm unable to reinstall Windows XP Professional (with SP2 Slipstreamed) because Windows Setup didn't recognize the SATA disk. I have loaded the Promise Serial ATA Drivers at the begin of the installation (F6)...
I have also tried 2 different versions of the Promise SATA Drivers; the one that cames with my motherboard CD, and the most recent from the MSI website. But with both drivers the same result. How can i get my Serial ATA Harddisk get work with this motherboard?
Any help will be appreciated.
Thanks,
Computerfreakje.
PS : My specifications are the following:
MSI K7N2 Delta ILSR (Rev. 7.4)
AMD Athlon XP 2500+
2x 256MB Kingston PC3200 Dual Channel
ATI Radeon 9800 Pro 128mb (R360)
Western Digital 40GB ATA
Western Digital 160GB SATA

Thanks for your reply Richard,
My motherboard didn't came with a floppy (I have bought an bulk version..) I have created a SATA floppy by myself. (I have got the drivers from the motherboard cd..) These drivers are also good, right?
Which type of RAID Array should i create? Because i have only one SATA drive.....
I think the "auto" feature is the easiest way?
Thanks.
Computerfreakje.

MSI K7N2 DELTA L BSOD Booting to DIsk/XP CDROM

Similar Messages

Maybe you are looking for