MSI k8N neo 2 Plat: Wont turn on

I am having a serious problem with my mainboard. After some problems with the system not turning on i removed all the components including the CPU to try and illimnate any dead components stopping it from turning on. Once the board was empty of components i hooked up a PSU - in this state the Mainboard powered on straightaway (its just powers up without putting contact across the power switch pins). Thus i concluded that the CPU might be dead and ordered a new one.
I have the new cpu and put it in to test. Again i am still having the same problem only this time when you connect the psu upto it and put power to the PSU the fans twitch (like they get power and the mainboard goes into standby mode). But it still wont turn on, i havent tried the system with complete GFX and hdd's attached yet. Does anyone have any experience with this issue?
Thanks,
Peter Wright

Well i have actually had the system running before perfectly - its because i use vapour phase cooling, the system was running for over a week (i think i've had it running on both PSU's) - i had to reseat the vapour phase cooling .
It was only after putting the system back together that it stopped functioning. I managed to get it to turn on but it was in like a reset state where all you could tell was the system was booting up to the point before the beep but just looping back to this point - possibly caused by the short on the 2 pins in the IDE socket on the board. but nothing since.

Similar Messages

Quick Question MSI K8N NEO 4 PLAT SLI

Hey guys,i am new to this forums just needed some help, i am about to purchase a:
AMD 64 3000 VENICE
LEDTEK 6600 GT PCI EXRESS GDDR3
CORSAIR VALUESELECT 1GB RAM DUAL CHANNEL
MSI K8N NEO 4 PLAT SLI
EPOWER 450 WATT PSU
i was wondering woud i need to update the bios 1st or will the stock bios that comes with the motherboard will work with the venice. I am getting all these parts from Zip Zoom Fly, accept the PSU. Thanks for your help.

Quote from: Dream_true on 28-June-05, 08:14:40
Only BIOS 1.4 and above support Venice & San Diego. However BIOS 1.4 has shut-down issue with RAID. It is suggested that you let your reseller help you flash BIOS to the latest version 1.5. After flashing BIOS, Loading Optimized defaults is needed of course. Good Luck!
Support new features in that cpuid yes. But that is not the same as you are not able to boot/post your system
with an earlier bios .
I booted up a venice on a K8N Neo2 with an aged 1.3 bios (with no venice SD support) just fine .
If the bios supports 90nm cpu it will post .
New CPUID added means :
Shown on post (display)
And e.g new model spesific features (like e.g SSE3 ) enabled .
Use the CPUID instruction to properly identify the processor.
• Determine the processor type, stepping, and available features by using functions 0000_0001h
and 8000_0001h of the CPUID instruction.
• Boot-up display - The processor name should be displayed according to the processor name string
defined in CPUID Guide for the AMD Athlon™ 64 and AMD Opteron™ Processors, order#
25481.
Chapter 12 , Bios and Kernel developers quide for athlon 64 . 26094.PDF

MSI K8N neo 2 Plat System still to be Built from Scratch!!!

Hi to all,
My first post and it's gonna be lengthy I think!
I am not a gamer ever, most of what I do is Video encoding (mainly this 100% CPU hogging activity) and Graphics manipulation.
Below is a list of what I have to start my build:
Note that I do not overclock ever so please, no reference to this!!!
MSI K8N Neo2 Platinum (7025)
Athlon 64 3500+ 92nm Winchester Core (retail)
Cooler = Zalman CNPS7000B-CU Ultra-Quiet CPU Cooler (think I might have fitting probs with memory slots DIMM's 1+2(G/P) on the MSI Neo2 Plat board, DIMM's 3+4(G/P) might be my only option if I want to stick with this cooler but for fault finding purposes I can always use the stock cooler?)
Corsair TwinXL PC3200 - CMX512-3200XLPRO 400Mhz 2.2.2.5 LL
Antec True Power 550W with SATA supply (X2)
1 X Western Digital 74Gb SATA Raptor HDD (I want this as my C: main boot, no Raid)
2 X Seagate Barracuda 300Gb 7K2rpm SATA HDD (I want these as RAID 0/stripe=performance only)
GPU: On order!
http://www.msi.com.tw/program/products/vga/vga/pro_vga_detail.php?UID=636
Will use my old trustworthy and reliable GeForce 2 Ti 64 Mb card for XP+SP1 instalation only.
1 X 120 Gb 7K2 HDD (IDE 1 Master) (from old set up)
1 X 120 Gb 7k2 HDD (IDE 1 Salve) (from old set up)
1 x PlexWriter 52x/24x/52x CD-ReWriter (IDE 2 Master)
1 X Pioneer DVR-108 Black16x DVD±RW Dual layer (IDE 2 Slave)
PCI = Creative Sound Blaster Audigy 2 Value 7.1 PCI Sound Card - OEM
Case = Lian-Li PC V1100 Black Aluminium Midi-Tower
Everthing is new in this set-up apart from my old IDE HDD's, still in boxes and ready to go ready for your input?
Q1. Quote
Keep in mind that you will need the special drivers to install your SATA Raid drives if you have any. When the windows install starts you need to keep tapping the F6 key to load those drivers from the diskette MSI supplied. "If you are using an Nvidia3 chipset with a single SATA drive and not raiding, you can skip this step, it will automatically be recognized by windows." (Tip Provided by timkessler)
Straight forward if you are using one or the other methods mentioned in Tiresmokes thread Basic Building Tips(which is gr8, thnx for that Tiresmoke). But as above I want my W/D raptor as my C: main boot drive only, no RAID?
Can I use the F6 option at the XP instal and then go on to set up the Raptor drive accordingly - and from there set up my 300Gb Seagates as RAID 0 (Seagates wont be attached till Raptor is set to C: main boot)???
Once I get to this stage I will start asking about board BIOS and Driver details which I dont know as of yet, like I said everything is still boxed.
I thought personally that starting this thread - people wanting to use this board would benefit from a brand new instalation from scratch guide from a relatively newbie point of view?
I know there are alot of issues regarding the boards features, but I thought if I done this in public the relevant problems could be linked as I go along, either with problems or without - depending on the individual experience?
pheeeewww, I said it was gonna be lengthy didnt I?

Quote
Originally posted by Supershanks
On install windows will see 3 drives all sata which is why i suggestd the configuration, i did you dont need to set up your raid array at all as the drives are just going to be data drives.
If you wish you could even install windows without f6 & loading any drivers
Having then got widows installed.
Seperate project to
enable raid in bios, creating the raid & let windows install drivers later.
assuming you have an original windows cd ie pre sp1, the quickest method of installation is to slipstream windows.
Basically you download latest service pack sp1 or sp2 insert your OS cd & run a program which merges the 2 & creates a new OS cd with the SP integrated. Any updates needed then are miimal.
see
Slipstreaming - Autostreamer Neowin - i'ts so easy i've heard grannies can do it
hope this helps
Looks like they moved the AutoStreamer thread, and updated to 1.033---> AutoStreamer 1.0.33

Msi k8n neo 2 plat usb problems

ok just built this rig and having minor difficulties with usb ports. have my mouse pluged into usb port. at first everything was fine, but within seconds of starting windows my mouse will first lag out for a second or two then it will totally die. i plug the mouse into the usb ports in the rea of my computer. after the mouse totally dies i plug it into a diffrent usb port either front or back and the same thing will happen. it will work for five minutes then just totally die. all the drivers are installed ( almost positive, downloaded sp2 and latest drivers from msi site) and i dont know what to do. could it be the mouse or is it the board? please help cause if it is the board i need to rma it as soon as possible b4 my 30 day free shipping period is up, thanks for anyinput u can give me.

Do you have any other USB devices? Are they working OK?
Does your mouse work OK with any other computer?
Without anything else to go on its very difficult to diagnose, but as a guess I would say your mouse is faulty.
Chip

System setup advice for MSI K8N Neo 2 Platinum.

Here is the PC I'm putting together:
Enermax EG465P-VE Noisetaker PSU with 29A on combined 12v rail
5v=30A 3.3v=30A 12V1=18A and 12V2=18A (comb 12v=29A)
MSI K8N Neo 2 Plat
AMD 3000+ winchester Retail box (carefully replacing AMD shin etsu with Artic Silver 5)
WD 80GB 800JB 7200 rpm EIDE HD
OCZ 2 x 256 PC3200 Premier Dual Chan Memory (2.5-3-3-7) (List on MSI website as ok)
Matrox G400 max
adaptec 2930u scsi adapter
Pioneer 303S 6x scsi DVD rom
Umax 1200S scsi scanner
Plextor 24/10/40 EIDE CDRW
External USR robotics serial modem
Microsoft regular keyboard PS2
Logitech regular wheel mouse PS2
regular old 1.44 MB floppy drive
Installing Win XP Pro upgrade (have my 98SE CD)
In the future I will possibly ditch my scsi DVD rom and replace with NEC dual layer burner and replace Plextor CDRW with 52/32/52 CDRW/DVD ROM. For now I'm going with what I have.
No plans to overclock now if ever. Perhaps a small amount later. Maybe 2.0 ghz? Maybe no overclocking at all.
Not a gaming rig really, although I'll try the odd game at low resolution.
So is there anything I should do ahead of time? I am carefully installing the board in the case and everything that goes with it. What sort of configuration setups should I do? Do I flash to a more updated BIOS first? Do I leave onboard things un-activated first? How do I setup my memory? For instance, I may look for the best BIOS to start with and have it ready to use if I have problems. I may also use the nVidia drivers for onboard audio instead of the realtek drivers.
Not looking for all the answers, just feel free to point out any of the obvious which may save me time
thanx in advance for any help

There is a compatibility issue betwen the Matrox G series cards and the MSI Neo Platinum motherboards, which AFAIK, hasn't been solved yet. The problem seems to be a result of changes made in the newer versions of the MSI bios, however you may be stuck if you need a newer bios for the Winchester cpu. You can find out more if you do a search on Matrox in this forum.
Robert

MSI k8N Neo Plat 2...system freeze and crash during h-end gaming...

MSI k8N Neo Plat 2
AMD athlon 64 3800+
Centon 512 MB DDR 3200 x 4
nvidia geforce fx 5700
win xp pro
Creative Audigy 2
Under some graphically intensive situations, during gaming, especially dealing with alot of background visuals, like fire/lava, etc, the system will after a short while of playing either, crash, freeze, reboot, or freeze while a loud screeching nosie emits from my speakers...I have tried updating my graphx card drivers to the most recent and the symptons still persist..Is there something I need to set in BIOS regarding mem timings, I have tried playing around some, but that hasnt worked either...Any help would be greatly appreciated !!!
,

Try raising RAM voltage to 2.7v - 2.8v.
If no go - Run Memtest86 http://www.memtest.org/#downiso
If no go - Try onboard Audio ( disable / remove Audigy2 )

Msi k8n neo plat problems

I have built 2 computers exactly the same.
msi k8n neo plat
512 corsair xms ddr 3200
8og sata maxtor
amd 64 3200
128mb ati 9800 pro
asus cd drive
When i tried to install windows xp pro on both the machines i got the same error. could not copy file. On each try the file was a different one. After hours of trying new things i found that putting the memory in slot 2 on the motherboard solved the problem, windows installed and booted up as norm. When i moved the memory back to slot 1 the computer would not boot.
I have now left the memory in slot 2 but the computer will still crash every hour.
I am sure this is something to do with the memory but not sure what the problem is.
Can anyone help.

Can anybody tell me what i should set the cpu fsb frequency to in the bios.
I just read this in the faq
What is the fsb speed of this cpu?
Depending on which FSB you are asking about: The Athlon 64's have the memory controller built in (which was previously part of the Northbridge on the motherboard) which uses up to 200MHz DDR Memory (400MHz FSB) The HyperTransport link from the CPU to the rest of the motherboard runs up to 800MHz. Just to expand on my answer... The HT link is 800MHz, but it's 16 bit in size (2 bytes worth of data per clock) the total bandwidth of the HyperTransport link is 3.2GB in total - 1.6GB sending data to CPU and 1.6GB receiving data from CPU.

MSI K8N NEO PLAT + CD / DVD-RW Drives

Hi, i have the msi k8n neo plat. I recently had to replace my old mobo due to the old power supply blowing or something. So i got me a 480watt enermax coolergiant psu. Replaced the mobo for a new msi k8n neo plat. Put the mobo in and psu. Working fine and dandy. Now i installed 64bit xp to primary, and ive had it running for for about 2 weeks. Went to install linux to the second hard drive, so i changed the boot order, saved settings and went to load disc...however now my cd and dvd drives dont work, and they dont work in windows either.

Can anybody tell me what i should set the cpu fsb frequency to in the bios.
I just read this in the faq
What is the fsb speed of this cpu?
Depending on which FSB you are asking about: The Athlon 64's have the memory controller built in (which was previously part of the Northbridge on the motherboard) which uses up to 200MHz DDR Memory (400MHz FSB) The HyperTransport link from the CPU to the rest of the motherboard runs up to 800MHz. Just to expand on my answer... The HT link is 800MHz, but it's 16 bit in size (2 bytes worth of data per clock) the total bandwidth of the HyperTransport link is 3.2GB in total - 1.6GB sending data to CPU and 1.6GB receiving data from CPU.

Msi k8n neo plat and audio problem

got me a msi k8n neo plat, great board but have a few minor problems that i have noticed. one is the audio problem i have- when i listen to winamp, and surf, i will loose my winamp connection surfing, and then have to start winamp. is this a bios thing, or nvidia platform or chipset problem?

Hi
Thats the Nvidea board, this is the via board forum. You want forum below this one, as they will be able to help better.
good luck
jocko

Msi k8n neo plat and microsoft ie

getting my msi k8n neo plat board running satisfactory , except for one problem . when i got to amdmb.com, i start surfing the site, and after a minute or 2, i get a microsoft ie error, send the error report to microsoft, and then ie closes. what is the problem , is it with amdmb.com site? its the only site that this problem with ie is present, all other sites i don,t have this problem

just tryed using the browser firefox, and it works great. its just ie that doesn,t work on amd.mb, and only that site. wierd problem, never experienced anything like it before. had run a short memtest , no errors. the 6800gt , msi k8n neo plat and amd 64 3400 work great. get some super madonion benchmarks-all default-1024 x 768 32bit- 22,755. i was hoping for 22,000, but exceeded my expectations. can get into the 23,000 + with overclocking the 6800gt, have had it overclocked at gpu-412, memory 1.12. not sure how much more you can increase the numbers, thinking my gpu is close to the limit at 412.had a problem with windvd, it ended up being a configuration in windvd- had to enable hardware acceleration , bingo- worked great after that. got my corsair xms pc 3200 to work at 6-3-3-2 timings. still getting to know the board, there is definately a learning curve to be delt with on this board, but i am getting it to work better by the day.

Msi k8n neo plat and 3dmark03

with my msi k8n neo plat , bfg 6800gt, and amd 64 3400 clawhammer- i get 11,114 in 3dmark03. seems like i should be getting a higher score-any suggestions.

You appear to have misread my post, read carefully, I said "at clock speeds" not "at stock speeds" which I think is where u misunderstood. I know it's overclocked, but who isn't going to if there is so much headroom? With coolbits you can have higher speeds when running 2d or 3d applications to keep temps low and for longevity of the card.

Overclocking msi k8n neo plat

trying to overclock my msi k8n neo plat and run mad 2001
hardware - amd 64 3400
bfg 6800gt
corsair pc3200
i go into bios and set ram at 400mhz, set agp at 67 mhz. then open center and enter 210 mhz fsb. when i start madonion, it freezes. is it my memory?

Could be a ram incompatibility issue. I have some OCZ pc3500 EL which is great in my other systems, but doesn't work in the Neo without bluescreens and crashes to desktop. It might also be a power related issue. What type of power supply are you using and what is the amperage on the 12v rail? That seems to be pretty important for this board.

Msi k8n neo plat : blue screen

hi
just built a amd 64 3400 with msi k8n neo plat: with xfx 256 geforce nvidia graphic n kinston 512 ddr 400.
but for some reason its giving the blue scree with dumping memory msg on the screen.changes the memory but still got the same problem updated the bios to 1.5 still same thing.
any cue with the problem.
thnks

Duplicate Thread
https://forum-en.msi.com/index.php?threadid=72851

Msi k8n neo plat nforce3 250gb : blue screen

hi
just built a amd 64 3400 with msi k8n neo plat: with xfx 256 geforce nvidia graphic n kinston 512 ddr 400.
but for some reason its giving the blue scree with dumping memory msg on the screen.changes the memory but still got the same problem updated the bios to 1.5 still same thing.
any cue with the problem.
thnks

System restore? You need to find out what's causing the problem and you have too many things connected to it to be able to figure out what it is, always start with a basic system - video, primary hard disk, cd + fdd, no more and nothing else connected. Then when something goes wrong along the way you'll have more chance of narrowing it down if the problem appears.
What you'll want to do now is disable/uninstall/unplug any additional non-system-critical components that you have connected to it such as extra usb slots, printers, scanners and anything else. Keyboard, mouse, video with no sound and see if the problem persists. If it does, try another video driver. If it's fixed then reconnect/enable one device and try again until the problem reappears and you can find out what's causing it -- unless you can speed read that message quickly before it shuts down
Now that I think of it, have you set the OS to not automatically reboot on any errors? That might keep the BSOD up there so you can note it down and hopefully point at the problem instead of going through all the above hassle ^^

MSI K8N Neo Plat edit. and IDE

Can anybody tell me how many IDE units you can run on this motherboard? I do not want to use raid 0 or 1. I have a KT3 ultra - aru at them moment with 6 single IDE units, but now I need to upgrade.
Thanks for any help.

Hi,
you can connect 4 IDE devices and 4 four sata devices on MSI K8N Neo Plat editition.
If it's not enought you can plug an IDE PCI card....

MSI k8N neo 2 Plat: Wont turn on

Similar Messages

Maybe you are looking for