MSI K8N NEO MS-7030 and SpeedFan

Can I use speedfan program to adjust the power supply 's RPM speed ??

Honestly I don't know, never tried.
The P/S would have to have a remote fan lead and be plugged into the motherboard. If you have that setup I don't see why not..

Similar Messages

MSI K8N Neo 2 Platinum and pci

i have a problem with my neo 2:
The mainboard dont recognize my Soundblaster audigy 2 zs.I tried every pci slot with bios 1.3, 1.36 bitpower and 1.4, but nothing.
Some one can help me?
this is my sistem: A64 3500+ winchester | MSI K8N Neo 2 Platinum | OCZ EL PC-3200 DC Plat. Rev. 2 2X512 MB | Sound Blaster Audigy 2 ZS 7.1 | Powercolor X800 XT Platinum Edition | Hitachi 7K250 80GB SATA | Maxtor D740X 40GB ATA | Maxtor DiamondMax Plus 9 40GB ATA

no overclock at moment and the sound card of mb is disabled.
i tried another pci card but no way. Not dedected from sistem.

MSI K8N NEO 2 platinium and ATI X800XL

SYS SPEC
CPU - AMD 3200+
MB - MSI K8N NEO 2 PLATINIUM
AGP -ATI X800XL
PSU- ANTEC TP2 550
HD - SEAGATE 80 GB SATA
DVD - ASUS DVD ROM
RAM-KINGSTON PC 3200 DDR 1 GB Dual channal .
My sys was running fine since 7 months i built this set up . some how it gives me bluescreen when it was on idle
I was using 7.1 ati drivers since it came out . my psu voltages are fine and my agp temp is 44 c idle . Never overclock the system . Cpu temp idle 40 . load 54. I Went to
save mode and clean the driver using dc pro and reboot it comes fine and i again installed the drivers . same
bsod happens again went into save mode opened device manager and see 8 yes 8 readon x800 installed and
having yellow mark on it . after that i reset cmos with battery out for 15 minutes . reformat my drive completely
installed freind ATI 9200 SE . when installing the driver for it. it gave me the error of installing the standard vga
driver before installing the ati driver which i did not understand and quit the setup . SYSTEM runs fine with safe
mode or normal windows xp with no driver installed for agp .Also did reinstall the x800xl and reboot same 8
GPUS installed in device manager . uninstall all of them and reboot again same thing in device manager .Another
thing i have done is to run anti virus on line scanning before HDD format it came out clean .Tryied several versions of drivers including 6.9, 7.1. 5.4 . I never seen this
kind of problem before in any forum as far as i read . HELP ME OUT IF ANY ONE CAN . THANKS

Quote from: ASIF BROHI on 28-February-07, 01:16:41
I reformated the drive two days ago when this problem occurs also used dc pro in safe mode and reboot and install the agp drivers again same problem after that . yup i installed the chipset drivers too ver. 5.10
Did you install the chipset drivers before the vga drivers?

MSI K8N Neo Plat edit. and IDE

Can anybody tell me how many IDE units you can run on this motherboard? I do not want to use raid 0 or 1. I have a KT3 ultra - aru at them moment with 6 single IDE units, but now I need to upgrade.
Thanks for any help.

Hi,
you can connect 4 IDE devices and 4 four sata devices on MSI K8N Neo Plat editition.
If it's not enought you can plug an IDE PCI card....

MSI K8n Neo Platinium ( 7030 NMS ) anb BIOS.

I have a MSI K8n Platinium ( 7030nms )
Recently, I update the bios to the last version, with this BIOS, at more of 220 Mhz to FSB ( A64 3000@2200 Mhz ) system don't start, before the update the system runs perfectly at 2350 Mhz ( 235 FSB ) and unestable at 2400 Mhz ( 240 FSB).
¿ What it's the problem with new bios ?
I tryed flash a old version, the 1.2 or 1.3, but isn't possible, the flash program tell me of a bios protection, and jumper balblabla....
Please help me !

There are plenty of beta verions I'm currently running 1.5B6 very stable.
you can see them on
Syar2003's Bios Link
Quote
What BIOS ver. it's recomended ?
Try this thread to see feedback K8N Neo and Neo2 Bios Collection. *Updated 140 official for Neo2
luck

MSI K8N NEO AGP Clip and XFX 6800 anyone ?

I just got XFX 6800 AGP on my K8N NEO nf3 250GB , when I plug in the card , the clip of the agp slot didn't lock the card at the end of it.
The card is working , should I worry ?

As long as you have the bracket end of the card screwed down tighly into the case & your mobo is secure, I wouldn't worry about it. Unless you just like to move & bounce your box around a lot.
My AGP clip appears to lock down (i.e. it moves into its proper place when the card seats) but it's not even close to being tight.
I can pull my BFG 6800 card right out without touching locking clip after I unscrew the PCI bracket... good thing too, it's a real ba$tard to reach.

Will the geforce 6800 fit in msi k8n neo ms- 7030 ??

please see this picture
http://www.hardwarezone.com/img/data/articles/2004/1247/msi_capacitor_bloc.jpg
http://www.hardwarezone.com/articles/view.php?id=1247&cid=6&pg=12

Might help a tad:
https://forum-en.msi.com/index.php?topic=86098.0

Usb header msi k8n neo ms-7030 ver:1

to anyone who can help! i am trying to hook up usb connections from the cables that came with my case (that are for front usb ports). the problem i am having is that only the top row of pins is/are active. the bottom row won't read or display anything at all. i have tried to go into the device manager and trouble shoot, though to no avail. all drivers are updated or "cannot find a better match." frustrating this is.... i have updated the bios, usb is enabbled in the bios ect, ect, ect...... is there anything else i can do?

ok, i understand do not connect the number 5 or 10 pin and none of them are. all wires are in the correct positions, i have one usb connection taking up one header and the other header is full (one row going to front usb, the other to SOHOUSB 3.5 internal card reader** all drivers installed).

MSI K8N NEO PLATINUM (RAM/HD problem/mobo problem?) [SOLVED]

my setup:
windows xp pro sp2
amd athlon 64 3200+
msi k8n neo plat - 7030 - bios 2.1
x800 xt vid
sound blaster audigy 2
kingston valueram pc3200 2x512 cas 3-3-3-8
ps = antec 430 watt truepower power supply (20 A on 12V)
I dont know if you guys remember my but i created a topic on here a while back about how my keyboard and mouse suddenly stopped working, well that turned out to be that the msi k8n neo platinum just went bad. So i RMA'd it and recently got the replacement board (with latest bios already installed). It worked completely fine for about a day. Well that same day i got it back, i installed a Logitech G7 USB wireless mouse. after i installed it, i began getting numerous windows stop blue screen errrors, even after i removed the mouse from control panel. So i figured i should format because to rule out everything and start fresh. So i did a FULL format and attempted the reinstall windows again. AFTER the format and BEFORE windows attempted the continue installation, i got the same stop error. I figured now this was a hardware problem. So first i tested RAM. I got the latest version of memtest86 and let it run for 4 hours (11 passes) with NO errors at all. Secondly, i got a western digital hard drive diagnostic program to test for failing hard drive and again no problems with that. I still suspected ram so i tried to boot with only 1 stick installed (in first slot), however the PC didnt boot at all (cleared cmos too). So i moved it to the second slot and cleared cmos again and this time it posted but it just hangs at a cursor and does nothing, same thing happened with third slot. I tried this same procedure clearning cmos each time with the second ram stick and got the SAME results. Shouldnt the motherboard boot with only 1 ram stick installed? Did MSI RMA me another bad board? Any help would be appreciated. thanks.

Quote from: russellmrgn on 28-March-06, 10:54:39
Sap147
Can you give us what the D-Bracket was showing ie
R R
G R
As an example this means "Initializing Keyboard Controller"
You will find this information in the manual page 2-23. (On mine) under Hardware Setup
Also can you please do all your tests with the ps2 keyboard and mouse and for now leave your Logitech G7 USB wireless mouse to one side.
Russell
for two sticks of ram = RR
GG
for one stick of ram = GR
GG
as for the g7, it hasnt been plugged in at all, i took it out long ago.. as for the ram, the timing was set to 2T, no overclocking, i will try 2.7 v and let you know, but for the record, it has been running at normal voltage settings for about a year perfectly fine.

MSI K8N Neo 4 CPU cooler is slowing down ?!

Hi everyone and HAPPY NEW YEAR TO ALL AND ALL THE BEST!!!
I have brand new MSI K8N Neo 4 mobo and something strange is going on. CPU cooler on Venice 3000+ s939 in BIOS is rotating on 2200 RPM, but when i start Win XP, Core center and Everest are showing only 1000 RPM. Cool'n'quiet is disabled in bios.
Is there some setting that I did'nt see or what?
Thanks for your help in advance.
Pufta.

Hi!
Thanks Hodgie_ns for your fast reply, but it was not set up in Core Center for Cool'n'quit to slow down, it was on user setting to maximum.
Problem resolved by connecting the CPU cooler on the other connector for SYS FAN for little time, then I connected back to the CPU FAN connector. Since then, it is working on 3000 RPM all the time. Funny?! Wird?! Bug?!
Thanks and go for it!

Help MSI K8n Neo 2 Platinum

Good Day I bought a MSI K8N NEO Platinum recently and have these doubt ! I[m not upgrade the Bios because the system functions perfectly but verified that version 1.2 says Support FSB you 450MHz. What this wants to say? I gain more performance? Another versions described terms : - Update NVPXE version you the 2.03.0469. - Update CBROM version you the 1.47. - Update NVRAID version you the 4.81.
What it would be these terms?
Thanks a lot. Sorry my English

If your board is stable and you like it the way it is, there is no reason to update the bios. You should only update the bios if it pertains to you.
Support 450MHz FSB is probably refering to speeds you can attain with overclocking.
NVPXE is for booting off of the LAN. I doubt you need to worry about this.
CBROM don't know
NVRAID is to update the bios for the RAID, but again if you are having no problems with it there is no need to upgrade.
Good Luck
Jeremy

K8N Neo (MS-7030) problem with Gigabyte 6600

Hi,
I got a problem with my K8N Neo (MS-7030) and Gigabyte 6600 together.
I just tried to upgrade my system with the following components:
PNY 5700LE 128M -> Gigabyte 6600 256M (GV-N66256DP)
Onboard sound -> CreativeLab SB Audigy 2 ZS Gamer
Here is my order of installation:
1. Win XP with SP2
2. Chipset driver 5.10 (5.11 crashed during installation)
3. ForceWare 81.98 (I tried 77.72 from Gigabyte as well)
The system went blank during (3) and never comes back. In the last 3 days, I must repeated the above procedures over 20 times. I tried combinations of diffierent version chipset driver with forceware, but still no luck.
Audigy2 was sitting in the middle PCI before. However, I encounter a few system lockup during the first 10 trials, then I found a post say Audigy 2 should reside in the orange, or the one far away from AGP, PCI slot. Things seems better after this change.
More detail about my system:
MB: K8N Neo (MS-7030) BIOS is the latest version, 1.9.
RAM: Corsair Value 2 x 512MB PC3200
PS: Antec 380W
Video: Gigabyte 6600 256M (GV-N66256DP)
Sound: CreativeLab SB Audigy 2 ZS Gamer
Thanks
Alex

Hi,
My PSU is Antec True3808 (5V/35A 12V/18A 3.3V/28A)
I forgot to mention before. The CPU is AMD Athlon 64 2800+.
Also, I had enough of installation for now. I pulled the new 6600 and put the old 5700LE back in. Now, I installed everything without a problem.
Could it be not compatible? PSU issue? Or something else?
Any suggestion?
I appreciate any help.
Alex

MOVED: MSI K8N Neo Platinum (MS-7030) won't post and just beeps

This topic has been moved to AMD64 nVidia Based board.
MSI K8N Neo Platinum (MS-7030) won't post and just beeps

1)Main Menu - No Post/No Boot problems and fixes - Bios-Central Award Bios Beep Codes + others
2) Memtest86+ As Stated
3) Power Suppy Requirements & Selection
4) Post Specs re Powe supply 3.3v 5v & 12v Amps., Gfx cards Drives etc.,

LiveUpdate broke the bios on a MSI k8n neo v2.0, need bios and recovery files.

LiveUpdate broke the bios on a MSI k8n neo v2.0, it need bios and recovery files. I do not know the serial number. The ERP is 070. Its a "k8n neo v2.0" "ms - 7030 ver: 20c" mainboard. I don't know the previous bios version. The computer prompts for a recovery disk during an AWARD BootBlock BIOS v1.0 initialization.
Thank You.

Here it is
[K8N Neo V2.0 series ==> 601-7030-070/080, BIOS 5.xx]
Sign On: K8N Neo V2.0 Series W7030NMS V5.4 031506 14:55:37

*UPDATED 7/15/04* Complete guide to bioses, drivers, and needed files for the MSI K8N Neo Platinum

Complete newbie's guide to bioses, drivers, and needed files for the MSI K8N Neo Platinum:
Last Updated: Thursday July 15th, 2004
Bioses:
(In order of date released.)
1.1b3 - (Download)
- Pre-1.1, given to reviewers to use in their reviews and benchmarks.
- Less stable, but supposedly you get slightly better overclocks.
1.1 Official - (Download)
1. This is AWARD BIOS release
2. This BIOS fixes the following problems of the previous version:
- Memory always run DDR 200 when install single side DDR on DIMM2 & DIMM3.
- Windows 2000 can't format the RAID IDE HDD when plug in Promise 378 controller.
1.2b5 - (Download)
1.2b7 - (No Download Yet)
1.2b10 - (Download)
- First attempt to fix false temperature readings. Fixes it for some people with Newcastle cores and doesn't fix it for anybody with Clawhammer cores.
1.2b12 - (Download)
- Second attempt to fix false temperature readings. Fixes it for some people with Newcastle cores and some people with Clawhammer cores.
1.3b1 - (Download)
- Another attempt to fix temperature problems?
- Possibly fixes cold boot/power light issues?
1.2 Official - (Download)
1. This is AWARD BIOS release
2. This BIOS fixes the following problems of the previous version:
- System can't resume from S3 sometimes when install USB device.
- Support K8 Sempron CPU.
- Turn off keyboard LED in S3.
--Quick Guide for flashing BIOS, provided by MSI--
1. Create a MS-DOS boot diskette, then copy the the .exe and the bios file to the floppy disk. Both of these files can be found in the package you downloaded.
2. Press "Delete" and go to BIOS setup while computer bootup.
Check BIOS advanced features and see if BIOS flash write control is enabled
(This option must be enabled. If you can not find this setting, it means the BIOS can be
flashed.)
3. Boot from MS-DOS boot diskette and get a:\> prompt.
4. Type "", then press ENTER
5. The flash program will then ask "Do you want to save BIOS?", please press "N" for no. The when you see Press 'Y' to program or 'N' to Exit, please press "Y" to continue.
6. After flashing complete, remove floppy and reset the system .
7. Press DELETE or F1 when prompted at first reboot after flashing.
8. Load BIOS optimized defaults, then save settings and exits.
Drivers & Needed Files:
(Note: All these drivers are for Windows XP.)
Leaked Nvidia nForce3 Chipset Drivers Version 4.40
(Please use at your own risk, these are LEAKED drivers. Password for the .zip file is "ocworkbench rules". Also, you will need to rename the WinXP_2K folder in IDE to either WinXP or Win2K else the installer doesn't pick it up.) Thanks for the link Wonkanoby!
*NEW* Leaked Nvidia nForce3 Chipset Drivers Version 5.03
More leaked drivers? Seems some parts of the drivers are older and some are newer.
1. Windows XP Service Pack 1A (Web Install) -or- Windows XP Service Pack 1A (Full Install)
2. Microsoft DirectX 9.0b (Web Install) -or- Microsoft DirectX 9.0b (Full Install)
3. Nvidia nForce3 Chipset Drivers Version 4.24
4. AMD Athlon 64 Processor Driver Version 1.1.0.14
5. Nvidia Video Card Driver Version 56.72 -or- Omega Nvidia Video Card Driver Version v1.5303
(The Omega drivers are third party drivers optimized for gaming, most prefer these over the standard Nvidia drivers.)
5. ATI Video Card Driver Version 4.7 -or- Omega ATI Video Card Driver Version 2.5.51
(The Omega drivers are third party drivers optimized for gaming, most prefer these over the standard ATI drivers.)
6. Onboard Sound Driver (Realtek AC'97 Audio Codec) Version A3.61
It is HIGHLY reccomended that you install the drivers/needed files in the order listed above. Please note that there are two #5's because you either install one or the other depending on your video card, do not install both of them.
You will come across a problem here though. You can't install the chipset drivers without installing the Windows service pack and DirectX first, but the Windows service pack and DirectX installs need the internet to download files and you won't have working internet until you install the chipset drivers. Here's what I did to get around this. Instead of downloading the web install versions of Windows service pack and DirectX, download the full version and and put them along with all the other drivers on a backup hard drive or burn them to a CD, this way you will have all the drivers you need when it's time to install them and none of them will require the internet to download files.
Another note when installing drivers. Apparently the Nvidia chipset drivers also come with drivers for the onboard sound, but people seem to agree that the Realtek onboard sound drivers are better. When you are installing the Nvidia chipset drivers, just be sure to uncheck the box for sound drivers when it asks you which drivers you would like to install. Now you can safely install the Realtek drivers without any chance of conflicting sound drivers. Thanks for the tip Wonkanoby!

Quote
Originally posted by RLiu818
Quote
Originally posted by Deviation56
Quote
Originally posted by RLiu818
You CAN install the nforce drivers BEFORE installing SP1. The only requirement to install the nforce drivers is DX9.
So is SP1 still recommended to install before the nforce drivers?
The installer still reccomends to install it beforehand for full USB 2.0 functionality... I would have put what you said in there but I wanted to keep it as simple as possible.
oh. IIRC the installer just says USB 2.0 will be fully functional after SP1 is installed. So after you install SP1 you go into device manager and u click update driver and it will auto search and update the driver.
Simplicity-wise, i guess its pretty much equal. It might take less preparation to just copy DX9 full onto a CD and install that first, then nforce driver, then right away you have yoru internet connection.
but i dunno.. i guess i will try it your way this time when my RMA"d board comes.
i will be fomratting and doing a fresh install later on today and will let you know if i come across any problems

MSI K8N NEO MS-7030 and SpeedFan

Similar Messages

Maybe you are looking for